| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
napi->poll can be called with budget 0, e.g. in netpoll scenarios
where the caller only wants to poll TX rings
(poll_one_napi@net/core/netpoll.c).
The below commit changed RX polling from "while" loop to "do {} while",
which caused to ignore the initial budget and handle at least one RX
packet.
This fixes the following warning:
[ 2852.049194] mlx5e_napi_poll+0x0/0x260 [mlx5_core] exceeded budget in poll
[ 2852.049195] ------------[ cut here ]------------
[ 2852.049195] WARNING: CPU: 0 PID: 25691 at net/core/netpoll.c:171 netpoll_poll_dev+0x18a/0x1a0
Fixes: 4b7dfc992514 ("net/mlx5e: Early-return on empty completion queues")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Martin KaFai Lau <kafai@fb.com>
Tested-by: Martin KaFai Lau <kafai@fb.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
After the panic teardown firmware command, health_care detects the error
in PCI bus and calls the mlx5_pci_err_detected. This health_care flow is
no longer needed because the panic teardown firmware command will bring
down the PCI bus communication with the HCA.
The solution is to cancel the health care timer and its pending
workqueue request before sending panic teardown firmware command.
Kernel trace:
mlx5_core 0033:01:00.0: Shutdown was called
mlx5_core 0033:01:00.0: health_care:154:(pid 9304): handling bad device here
mlx5_core 0033:01:00.0: mlx5_handle_bad_state:114:(pid 9304): NIC state 1
mlx5_core 0033:01:00.0: mlx5_pci_err_detected was called
mlx5_core 0033:01:00.0: mlx5_enter_error_state:96:(pid 9304): start
mlx5_3:mlx5_ib_event:3061:(pid 9304): warning: event on port 0
mlx5_core 0033:01:00.0: mlx5_enter_error_state:104:(pid 9304): end
Unable to handle kernel paging request for data at address 0x0000003f
Faulting instruction address: 0xc0080000434b8c80
Fixes: 8812c24d28f4 ('net/mlx5: Add fast unload support in shutdown flow')
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
list_splice_init initializing waiting_events_list after splicing it to
temp list, therefore we should loop over temp list to fire the events.
Fixes: 4ca637a20a52 ("net/mlx5: Delay events till mlx5 interface's add complete for pci resume")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull final power management fixes from Rafael Wysocki:
"These fix a regression in the schedutil cpufreq governor introduced by
a recent change and blacklist Dell XPS13 9360 from using the Low Power
S0 Idle _DSM interface which triggers serious problems on one of these
machines.
Specifics:
- Prevent the schedutil cpufreq governor from using the utilization
of a wrong CPU in some cases which started to happen after one of
the recent changes in it (Chris Redpath).
- Blacklist Dell XPS13 9360 from using the Low Power S0 Idle _DSM
interface as that causes serious issue (related to NVMe) to appear
on one of these machines, even though the other Dells XPS13 9360 in
somewhat different HW configurations behave correctly (Rafael
Wysocki)"
* tag 'pm-final-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Blacklist Low Power S0 Idle _DSM for Dell XPS13 9360
cpufreq: schedutil: Examine the correct CPU when we update util
|
|
Pull networking fixes from David Miller:
1) Fix use-after-free in IPSEC input parsing, desintation address
pointer was loaded before pskb_may_pull() which can change the SKB
data pointers. From Florian Westphal.
2) Stack out-of-bounds read in xfrm_state_find(), from Steffen
Klassert.
3) IPVS state of SKB is not properly reset when moving between
namespaces, from Ye Yin.
4) Fix crash in asix driver suspend and resume, from Andrey Konovalov.
5) Don't deliver ipv6 l2tp tunnel packets to ipv4 l2tp tunnels, and
vice versa, from Guillaume Nault.
6) Fix DSACK undo on non-dup ACKs, from Priyaranjan Jha.
7) Fix regression in bond_xmit_hash()'s behavior after the TCP port
selection changes back in 4.2, from Hangbin Liu.
8) Two divide by zero bugs in USB networking drivers when parsing
descriptors, from Bjorn Mork.
9) Fix bonding slaves being stuck in BOND_LINK_FAIL state, from Jay
Vosburgh.
10) Missing skb_reset_mac_header() in qmi_wwan, from Kristian Evensen.
11) Fix the destruction of tc action object races properly, from Cong
Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (31 commits)
cls_u32: use tcf_exts_get_net() before call_rcu()
cls_tcindex: use tcf_exts_get_net() before call_rcu()
cls_rsvp: use tcf_exts_get_net() before call_rcu()
cls_route: use tcf_exts_get_net() before call_rcu()
cls_matchall: use tcf_exts_get_net() before call_rcu()
cls_fw: use tcf_exts_get_net() before call_rcu()
cls_flower: use tcf_exts_get_net() before call_rcu()
cls_flow: use tcf_exts_get_net() before call_rcu()
cls_cgroup: use tcf_exts_get_net() before call_rcu()
cls_bpf: use tcf_exts_get_net() before call_rcu()
cls_basic: use tcf_exts_get_net() before call_rcu()
net_sched: introduce tcf_exts_get_net() and tcf_exts_put_net()
Revert "net_sched: hold netns refcnt for each action"
net: usb: asix: fill null-ptr-deref in asix_suspend
Revert "net: usb: asix: fill null-ptr-deref in asix_suspend"
qmi_wwan: Add missing skb_reset_mac_header-call
bonding: fix slave stuck in BOND_LINK_FAIL state
qrtr: Move to postcore_initcall
net: qmi_wwan: fix divide by 0 on bad descriptors
net: cdc_ether: fix divide by 0 on bad descriptors
...
|
|
When asix_suspend() is called dev->driver_priv might not have been
assigned a value, so we need to check that it's not NULL.
Similar issue is present in asix_resume(), this patch fixes it as well.
Found by syzkaller.
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
Modules linked in:
CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.14.0-rc4-43422-geccacdd69a8c #400
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
task: ffff88006bb36300 task.stack: ffff88006bba8000
RIP: 0010:asix_suspend+0x76/0xc0 drivers/net/usb/asix_devices.c:629
RSP: 0018:ffff88006bbae718 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff880061ba3b80 RCX: 1ffff1000c34d644
RDX: 0000000000000001 RSI: 0000000000000402 RDI: 0000000000000008
RBP: ffff88006bbae738 R08: 1ffff1000d775cad R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800630a8b40
R13: 0000000000000000 R14: 0000000000000402 R15: ffff880061ba3b80
FS: 0000000000000000(0000) GS:ffff88006c600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ff33cf89000 CR3: 0000000061c0a000 CR4: 00000000000006f0
Call Trace:
usb_suspend_interface drivers/usb/core/driver.c:1209
usb_suspend_both+0x27f/0x7e0 drivers/usb/core/driver.c:1314
usb_runtime_suspend+0x41/0x120 drivers/usb/core/driver.c:1852
__rpm_callback+0x339/0xb60 drivers/base/power/runtime.c:334
rpm_callback+0x106/0x220 drivers/base/power/runtime.c:461
rpm_suspend+0x465/0x1980 drivers/base/power/runtime.c:596
__pm_runtime_suspend+0x11e/0x230 drivers/base/power/runtime.c:1009
pm_runtime_put_sync_autosuspend ./include/linux/pm_runtime.h:251
usb_new_device+0xa37/0x1020 drivers/usb/core/hub.c:2487
hub_port_connect drivers/usb/core/hub.c:4903
hub_port_connect_change drivers/usb/core/hub.c:5009
port_event drivers/usb/core/hub.c:5115
hub_event+0x194d/0x3740 drivers/usb/core/hub.c:5195
process_one_work+0xc7f/0x1db0 kernel/workqueue.c:2119
worker_thread+0x221/0x1850 kernel/workqueue.c:2253
kthread+0x3a1/0x470 kernel/kthread.c:231
ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:431
Code: 8d 7c 24 20 48 89 fa 48 c1 ea 03 80 3c 02 00 75 5b 48 b8 00 00
00 00 00 fc ff df 4d 8b 6c 24 20 49 8d 7d 08 48 89 fa 48 c1 ea 03 <80>
3c 02 00 75 34 4d 8b 6d 08 4d 85 ed 74 0b e8 26 2b 51 fd 4c
RIP: asix_suspend+0x76/0xc0 RSP: ffff88006bbae718
---[ end trace dfc4f5649284342c ]---
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit baedf68a068ca29624f241426843635920f16e1d.
There is an updated version of this fix which covers
the problem more thoroughly.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we receive a packet on a QMI device in raw IP mode, we should call
skb_reset_mac_header() to ensure that skb->mac_header contains a valid
offset in the packet. While it shouldn't really matter, the packets have
no MAC header and the interface is configured as-such, it seems certain
parts of the network stack expects a "good" value in skb->mac_header.
Without the skb_reset_mac_header() call added in this patch, for example
shaping traffic (using tc) triggers the following oops on the first
received packet:
[ 303.642957] skbuff: skb_under_panic: text:8f137918 len:177 put:67 head:8e4b0f00 data:8e4b0eff tail:0x8e4b0fb0 end:0x8e4b1520 dev:wwan0
[ 303.655045] Kernel bug detected[#1]:
[ 303.658622] CPU: 1 PID: 1002 Comm: logd Not tainted 4.9.58 #0
[ 303.664339] task: 8fdf05e0 task.stack: 8f15c000
[ 303.668844] $ 0 : 00000000 00000001 0000007a 00000000
[ 303.674062] $ 4 : 8149a2fc 8149a2fc 8149ce20 00000000
[ 303.679284] $ 8 : 00000030 3878303a 31623465 20303235
[ 303.684510] $12 : ded731e3 2626a277 00000000 03bd0000
[ 303.689747] $16 : 8ef62b40 00000043 8f137918 804db5fc
[ 303.694978] $20 : 00000001 00000004 8fc13800 00000003
[ 303.700215] $24 : 00000001 8024ab10
[ 303.705442] $28 : 8f15c000 8fc19cf0 00000043 802cc920
[ 303.710664] Hi : 00000000
[ 303.713533] Lo : 74e58000
[ 303.716436] epc : 802cc920 skb_panic+0x58/0x5c
[ 303.721046] ra : 802cc920 skb_panic+0x58/0x5c
[ 303.725639] Status: 11007c03 KERNEL EXL IE
[ 303.729823] Cause : 50800024 (ExcCode 09)
[ 303.733817] PrId : 0001992f (MIPS 1004Kc)
[ 303.737892] Modules linked in: rt2800pci rt2800mmio rt2800lib qcserial ppp_async option usb_wwan rt2x00pci rt2x00mmio rt2x00lib rndis_host qmi_wwan ppp_generic nf_nat_pptp nf_conntrack_pptp nf_conntrack_ipv6 mt76x2i
Process logd (pid: 1002, threadinfo=8f15c000, task=8fdf05e0, tls=77b3eee4)
[ 303.962509] Stack : 00000000 80408990 8f137918 000000b1 00000043 8e4b0f00 8e4b0eff 8e4b0fb0
[ 303.970871] 8e4b1520 8fec1800 00000043 802cd2a4 6e000045 00000043 00000000 8ef62000
[ 303.979219] 8eef5d00 8ef62b40 8fea7300 8f137918 00000000 00000000 0002bb01 793e5664
[ 303.987568] 8ef08884 00000001 8fea7300 00000002 8fc19e80 8eef5d00 00000006 00000003
[ 303.995934] 00000000 8030ba90 00000003 77ab3fd0 8149dc80 8004d1bc 8f15c000 8f383700
[ 304.004324] ...
[ 304.006767] Call Trace:
[ 304.009241] [<802cc920>] skb_panic+0x58/0x5c
[ 304.013504] [<802cd2a4>] skb_push+0x78/0x90
[ 304.017783] [<8f137918>] 0x8f137918
[ 304.021269] Code: 00602825 0c02a3b4 24842888 <000c000d> 8c870060 8c8200a0 0007382b 00070336 8c88005c
[ 304.031034]
[ 304.032805] ---[ end trace b778c482b3f0bda9 ]---
[ 304.041384] Kernel panic - not syncing: Fatal exception in interrupt
[ 304.051975] Rebooting in 3 seconds..
While the oops is for a 4.9-kernel, I was able to trigger the same oops with
net-next as of yesterday.
Fixes: 32f7adf633b9 ("net: qmi_wwan: support "raw IP" mode")
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bonding miimon logic has a flaw, in that a failure of the
rtnl_trylock can cause a slave to become permanently stuck in
BOND_LINK_FAIL state.
The sequence of events to cause this is as follows:
1) bond_miimon_inspect finds that a slave's link is down, and so
calls bond_propose_link_state, setting slave->new_link_state to
BOND_LINK_FAIL, then sets slave->new_link to BOND_LINK_DOWN and returns
non-zero.
2) In bond_mii_monitor, the rtnl_trylock fails, and the timer is
rescheduled. No change is committed.
3) bond_miimon_inspect is called again, but this time the slave
from step 1 has recovered. slave->new_link is reset to NOCHANGE, and, as
slave->link was never changed, the switch enters the BOND_LINK_UP case,
and does nothing. The pending BOND_LINK_FAIL state from step 1 remains
pending, as new_link_state is not reset.
4) The state from step 3 persists until another slave changes link
state and causes bond_miimon_inspect to return non-zero. At this point,
the BOND_LINK_FAIL state change on the slave from steps 1-3 is committed,
and the slave will remain stuck in BOND_LINK_FAIL state even though it
is actually link up.
The remedy for this is to initialize new_link_state on each entry
to bond_miimon_inspect, as is already done with new_link.
Fixes: fb9eb899a6dc ("bonding: handle link transition from FAIL to UP correctly")
Reported-by: Alex Sidorenko <alexandre.sidorenko@hpe.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A CDC Ethernet functional descriptor with wMaxSegmentSize = 0 will
cause a divide error in usbnet_probe:
divide error: 0000 [#1] PREEMPT SMP KASAN
Modules linked in:
CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.14.0-rc8-44453-g1fdc1a82c34f #56
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
task: ffff88006bef5c00 task.stack: ffff88006bf60000
RIP: 0010:usbnet_update_max_qlen+0x24d/0x390 drivers/net/usb/usbnet.c:355
RSP: 0018:ffff88006bf67508 EFLAGS: 00010246
RAX: 00000000000163c8 RBX: ffff8800621fce40 RCX: ffff8800621fcf34
RDX: 0000000000000000 RSI: ffffffff837ecb7a RDI: ffff8800621fcf34
RBP: ffff88006bf67520 R08: ffff88006bef5c00 R09: ffffed000c43f881
R10: ffffed000c43f880 R11: ffff8800621fc406 R12: 0000000000000003
R13: ffffffff85c71de0 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88006ca00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffe9c0d6dac CR3: 00000000614f4000 CR4: 00000000000006f0
Call Trace:
usbnet_probe+0x18b5/0x2790 drivers/net/usb/usbnet.c:1783
qmi_wwan_probe+0x133/0x220 drivers/net/usb/qmi_wwan.c:1338
usb_probe_interface+0x324/0x940 drivers/usb/core/driver.c:361
really_probe drivers/base/dd.c:413
driver_probe_device+0x522/0x740 drivers/base/dd.c:557
Fix by simply ignoring the bogus descriptor, as it is optional
for QMI devices anyway.
Fixes: 423ce8caab7e ("net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting dev->hard_mtu to 0 will cause a divide error in
usbnet_probe. Protect against devices with bogus CDC Ethernet
functional descriptors by ignoring a zero wMaxSegmentSize.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 07f4c90062f8 ("tcp/dccp: try to not exhaust ip_local_port_range
in connect()"), we will try to use even ports for connect(). Then if an
application (seen clearly with iperf) opens multiple streams to the same
destination IP and port, each stream will be given an even source port.
So the bonding driver's simple xmit_hash_policy based on layer3+4 addressing
will always hash all these streams to the same interface. And the total
throughput will limited to a single slave.
Change the tcp code will impact the whole tcp behavior, only for bonding
usage. Paolo Abeni suggested fix this by changing the bonding code only,
which should be more reasonable, and less impact.
Fix this by discarding the lowest hash bit because it contains little entropy.
After the fix we can re-balance between slaves.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx5e_execute_l2_action
hn is being kfree'd in mlx5e_del_l2_from_hash and then dereferenced
by accessing hn->ai.addr
Fix this by copying the MAC address into a local variable for its safe use
in all possible execution paths within function mlx5e_execute_l2_action.
Addresses-Coverity-ID: 1417789
Fixes: eeb66cdb6826 ("net/mlx5: Separate between E-Switch and MPFS")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mvpp2 driver can't cope at all with the TX affinities being
changed from userspace, and spit an endless stream of
[ 91.779920] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.779930] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780402] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780406] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780415] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780418] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
rendering the box completely useless (I've measured around 600k
interrupts/s on a 8040 box) once irqbalance kicks in and start
doing its job.
Obviously, the driver was never designed with this in mind. So let's
work around the problem by preventing userspace from interacting
with these interrupts altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 0day bot reports the below failure which happens occasionally, with
their randconfig testing (once every ~100 boots). The Code points at
the private pointer ->driver_data being NULL, which hints at a race of
sorts where the private driver_data descriptor has disappeared by the
time we get to run the workqueue.
So let's check that pointer before we continue with issuing the command
to the drive.
This fix is of the brown paper bag nature but considering that IDE is
long deprecated, let's do that so that random testing which happens to
enable CONFIG_IDE during randconfig builds, doesn't fail because of
this.
Besides, failing the TEST_UNIT_READY command because the drive private
data is gone is something which we could simply do anyway, to denote
that there was a problem communicating with the device.
BUG: unable to handle kernel NULL pointer dereference at 000001c0
IP: cdrom_check_status
*pde = 00000000
Oops: 0000 [#1] SMP
CPU: 1 PID: 155 Comm: kworker/1:2 Not tainted 4.14.0-rc8 #127
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Workqueue: events_freezable_power_ disk_events_workfn
task: 4fe90980 task.stack: 507ac000
EIP: cdrom_check_status+0x2c/0x90
EFLAGS: 00210246 CPU: 1
EAX: 00000000 EBX: 4fefec00 ECX: 00000000 EDX: 00000000
ESI: 00000003 EDI: ffffffff EBP: 467a9340 ESP: 507aded0
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 80050033 CR2: 000001c0 CR3: 06e0f000 CR4: 00000690
Call Trace:
? ide_cdrom_check_events_real
? cdrom_check_events
? disk_check_events
? process_one_work
? process_one_work
? worker_thread
? kthread
? process_one_work
? __kthread_create_on_node
? ret_from_fork
Code: 53 83 ec 14 89 c3 89 d1 be 03 00 00 00 65 a1 14 00 00 00 89 44 24 10 31 c0 8b 43 18 c7 44 24 04 00 00 00 00 c7 04 24 00 00 00 00 <8a> 80 c0 01 00 00 c7 44 24 08 00 00 00 00 83 e0 03 c7 44 24 0c
EIP: cdrom_check_status+0x2c/0x90 SS:ESP: 0068:507aded0
CR2: 00000000000001c0
---[ end trace 2410e586dd8f88b2 ]---
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 8a97712e5314aefe16b3ffb4583a34deaa49de04.
This commit added a call to sysfs_notify() from within
scsi_device_set_state(), which in turn turns out to make libata very
unhappy, because ata_eh_detach_dev() does
spin_lock_irqsave(ap->lock, flags);
..
if (ata_scsi_offline_dev(dev)) {
dev->flags |= ATA_DFLAG_DETACHED;
ap->pflags |= ATA_PFLAG_SCSI_HOTPLUG;
}
and ata_scsi_offline_dev() then does that scsi_device_set_state() to set
it offline.
So now we called sysfs_notify() from within a spinlocked region, which
really doesn't work. The 0day robot reported this as:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:238
because sysfs_notify() ends up calling kernfs_find_and_get_ns() which
then does mutex_lock(&kernfs_mutex)..
The pollability of the device state isn't critical, so revert this all
for now, and maybe we'll do it differently in the future.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
At least one Dell XPS13 9360 is reported to have serious issues with
the Low Power S0 Idle _DSM interface and since this machine model
generally can do ACPI S3 just fine, add a blacklist entry to disable
that interface for Dell XPS13 9360.
Fixes: 8110dd281e15 (ACPI / sleep: EC-based wakeup from suspend-to-idle on recent systems)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196907
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 4.13+ <stable@vger.kernel.org> # 4.13+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Two fixes:
- A PCID related revert that fixes power management and performance
regressions.
- The module loader robustization and sanity check commit is rather
fresh, but it looked like a good idea to apply because of the
hidden data corruption problem such invalid modules could cause"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/module: Detect and skip invalid relocations
Revert "x86/mm: Stop calling leave_mm() in idle code"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Ingo Molnar:
"An irqchip driver init fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-mvebu-gicp: Add missing spin_lock init
|
|
Pull ARM fixes from Russell King:
- omit EFI memory map sorting, which was recently introduced, but
caused problems with the decompressor due to additional sections
being emitted.
- avoid unaligned load fault-generating instructions in the
decompressor by switching to a private unaligned implementation.
- add a symbol into the decompressor to further debug non-boot
situations (ld's documentation is extremely poor for how "." works,
ld doesn't seem to follow its own documentation!)
- parse endian information to sparse
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: add debug ".edata_real" symbol
ARM: 8716/1: pass endianness info to sparse
efi/libstub: arm: omit sorting of the UEFI memory map
ARM: 8715/1: add a private asm/unaligned.h
|
|
This reverts commit 43858b4f25cf0adc5c2ca9cf5ce5fdf2532941e5.
The reason I removed the leave_mm() calls in question is because the
heuristic wasn't needed after that patch. With the original version
of my PCID series, we never flushed a "lazy cpu" (i.e. a CPU running
kernel thread) due a flush on the loaded mm.
Unfortunately, that caused architectural issues, so now I've
reinstated these flushes on non-PCID systems in:
commit b956575bed91 ("x86/mm: Flush more aggressively in lazy TLB mode").
That, in turn, gives us a power management and occasionally
performance regression as compared to old kernels: a process that
goes into a deep idle state on a given CPU and gets its mm flushed
due to activity on a different CPU will wake the idle CPU.
Reinstate the old ugly heuristic: if a CPU goes into ACPI C3 or an
intel_idle state that is likely to cause a TLB flush gets its mm
switched to init_mm before going idle.
FWIW, this heuristic is lousy. Whether we should change CR3 before
idle isn't a good hint except insofar as the performance hit is a bit
lower if the TLB is getting flushed by the idle code anyway. What we
really want to know is whether we anticipate being idle long enough
that the mm is likely to be flushed before we wake up. This is more a
matter of the expected latency than the idle state that gets chosen.
This heuristic also completely fails on systems that don't know
whether the TLB will be flushed (e.g. AMD systems?). OTOH it may be a
bit obsolete anyway -- PCID systems don't presently benefit from this
heuristic at all.
We also shouldn't do this callback from innermost bit of the idle code
due to the RCU nastiness it causes. All the information need is
available before rcu_idle_enter() needs to happen.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 43858b4f25cf "x86/mm: Stop calling leave_mm() in idle code"
Link: http://lkml.kernel.org/r/c513bbd4e653747213e05bc7062de000bf0202a5.1509793738.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When asix_suspend() is called dev->driver_priv might not have been
assigned a value, so we need to check that it's not NULL.
Found by syzkaller.
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
Modules linked in:
CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.14.0-rc4-43422-geccacdd69a8c #400
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
task: ffff88006bb36300 task.stack: ffff88006bba8000
RIP: 0010:asix_suspend+0x76/0xc0 drivers/net/usb/asix_devices.c:629
RSP: 0018:ffff88006bbae718 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff880061ba3b80 RCX: 1ffff1000c34d644
RDX: 0000000000000001 RSI: 0000000000000402 RDI: 0000000000000008
RBP: ffff88006bbae738 R08: 1ffff1000d775cad R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800630a8b40
R13: 0000000000000000 R14: 0000000000000402 R15: ffff880061ba3b80
FS: 0000000000000000(0000) GS:ffff88006c600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ff33cf89000 CR3: 0000000061c0a000 CR4: 00000000000006f0
Call Trace:
usb_suspend_interface drivers/usb/core/driver.c:1209
usb_suspend_both+0x27f/0x7e0 drivers/usb/core/driver.c:1314
usb_runtime_suspend+0x41/0x120 drivers/usb/core/driver.c:1852
__rpm_callback+0x339/0xb60 drivers/base/power/runtime.c:334
rpm_callback+0x106/0x220 drivers/base/power/runtime.c:461
rpm_suspend+0x465/0x1980 drivers/base/power/runtime.c:596
__pm_runtime_suspend+0x11e/0x230 drivers/base/power/runtime.c:1009
pm_runtime_put_sync_autosuspend ./include/linux/pm_runtime.h:251
usb_new_device+0xa37/0x1020 drivers/usb/core/hub.c:2487
hub_port_connect drivers/usb/core/hub.c:4903
hub_port_connect_change drivers/usb/core/hub.c:5009
port_event drivers/usb/core/hub.c:5115
hub_event+0x194d/0x3740 drivers/usb/core/hub.c:5195
process_one_work+0xc7f/0x1db0 kernel/workqueue.c:2119
worker_thread+0x221/0x1850 kernel/workqueue.c:2253
kthread+0x3a1/0x470 kernel/kthread.c:231
ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:431
Code: 8d 7c 24 20 48 89 fa 48 c1 ea 03 80 3c 02 00 75 5b 48 b8 00 00
00 00 00 fc ff df 4d 8b 6c 24 20 49 8d 7d 08 48 89 fa 48 c1 ea 03 <80>
3c 02 00 75 34 4d 8b 6d 08 4d 85 ed 74 0b e8 26 2b 51 fd 4c
RIP: asix_suspend+0x76/0xc0 RSP: ffff88006bbae718
---[ end trace dfc4f5649284342c ]---
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change t4fw_version.h to update latest firmware version
number to 1.16.63.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just a couple of fixups to the sparse-keymap module and the Microchip
AR1021 touchscreen driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: sparse-keymap - send sync event for KE_SW/KE_VSW
Input: ar1021_i2c - set INPUT_PROP_DIRECT
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One fix for USB clks on Uniphier PXs3 SoCs"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: uniphier: fix clock data for PXs3
|
|
Sync events are sent by sparse_keymap_report_entry for normal KEY_*
events, and are generated by several drivers after generating
SW_* events, so sparse_keymap_report_entry should do the same.
Without the sync, events are accumulated in the kernel.
Currently, no driver uses sparse-keymap for SW_* events, but
it is required for the intel-vbtn platform driver to generate
SW_TABLET_MODE events.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
If INPUT_PROP_DIRECT is set, userspace doesn't have to fall back to old
ways of identifying touchscreen devices. Let's add it.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One minor fix in the error leg of the qla2xxx driver (it oopses the
system if we get an error trying to start the internal kernel thread).
The fix is minor because the problem isn't often encountered in the
field (although it can be induced by inserting the module in a low
memory environment)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix oops in qla2x00_probe_one error path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"Fix dw_mmc request timeout issues"
* tag 'mmc-v4.14-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: dw_mmc: Fix the DTO timeout calculation
mmc: dw_mmc: Add locking to the CTO timer
mmc: dw_mmc: Fix the CTO timeout calculation
mmc: dw_mmc: cancel the CTO timer after a voltage switch
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
- one nouveau regression fix
- some amdgpu fixes for stable to fix hangs on some harvested Polaris
GPUs
- a set of KASAN and regression fixes for i915, their CI system seems
to be working pretty well now.
* tag 'drm-fixes-for-v4.14-rc8' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: allow harvesting check for Polaris VCE
drm/amdgpu: return -ENOENT from uvd 6.0 early init for harvesting
drm/i915: Check incoming alignment for unfenced buffers (on i915gm)
drm/nouveau/kms/nv50: use the correct state for base channel notifier setup
drm/i915: Hold rcu_read_lock when iterating over the radixtree (vma idr)
drm/i915: Hold rcu_read_lock when iterating over the radixtree (objects)
drm/i915/edp: read edp display control registers unconditionally
drm/i915: Do not rely on wm preservation for ILK watermarks
drm/i915: Cancel the modeset retry work during modeset cleanup
|
|
Pull networking fixes from David Miller:
"Hopefully this is the last batch of networking fixes for 4.14
Fingers crossed...
1) Fix stmmac to use the proper sized OF property read, from Bhadram
Varka.
2) Fix use after free in net scheduler tc action code, from Cong
Wang.
3) Fix SKB control block mangling in tcp_make_synack().
4) Use proper locking in fib_dump_info(), from Florian Westphal.
5) Fix IPG encodings in systemport driver, from Florian Fainelli.
6) Fix division by zero in NV TCP congestion control module, from
Konstantin Khlebnikov.
7) Fix use after free in nf_reject_ipv4, from Tejaswi Tanikella"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: systemport: Correct IPG length settings
tcp: do not mangle skb->cb[] in tcp_make_synack()
fib: fib_dump_info can no longer use __in_dev_get_rtnl
stmmac: use of_property_read_u32 instead of read_u8
net_sched: hold netns refcnt for each action
net_sched: acquire RTNL in tc_action_net_exit()
net: vrf: correct FRA_L3MDEV encode type
tcp_nv: fix division by zero in tcpnv_acked()
netfilter: nf_reject_ipv4: Fix use-after-free in send_reset
netfilter: nft_set_hash: disable fast_ops for 2-len keys
|
|
MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:
- Have 10 or more patches in mainline authored using an @imgtec.com
email address, or any patches dated within the past year.
- Are still with Imagination but leaving as part of the MIPS business
unit, as determined from an internal email address list.
- Haven't already updated their email address (ie. JamesH) or expressed
a desire to be excluded (ie. Maciej).
- Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
myself.
New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list. An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.
Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Due to a documentation mistake, the IPG length was set to 0x12 while it
should have been 12 (decimal). This would affect short packet (64B
typically) performance since the IPG was bigger than necessary.
Fixes: 44a4524c54af ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Numbers in DT are stored in “cells” which are 32-bits
in size. of_property_read_u8 does not work properly
because of endianness problem.
This causes it to always return 0 with little-endian
architectures.
Fix it by using of_property_read_u32() OF API.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
FRA_L3MDEV is defined as U8, but is being added as a U32 attribute. On
big endian architecture, this results in the l3mdev entry not being
added to the FIB rules.
Fixes: 1aa6c4f6b8cd8 ("net: vrf: Add l3mdev rules on first device create")
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
into drm-fixes
Just two small patches for stable to fix the driver failing to load on polaris
cards with harvested VCE or UVD blocks.
* 'drm-fixes-4.14' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: allow harvesting check for Polaris VCE
drm/amdgpu: return -ENOENT from uvd 6.0 early init for harvesting
|
|
Fixes init failures on Polaris cards with harvested
VCE blocks.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Fixes init failures on polaris cards with harvested UVD.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Fixes for Stable:
- Fix KBL Blank Screen (Jani)
- Fix FIFO Underrun on SNB (Maarten)
Other fixes:
- Fix GPU Hang on i915gm (Chris)
- Fix gem_tiled_pread_pwrite IGT case (Chris)
- Cancel modeset retry work during modeset clean-up (Manasi)
* tag 'drm-intel-fixes-2017-11-01' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Check incoming alignment for unfenced buffers (on i915gm)
drm/i915: Hold rcu_read_lock when iterating over the radixtree (vma idr)
drm/i915: Hold rcu_read_lock when iterating over the radixtree (objects)
drm/i915/edp: read edp display control registers unconditionally
drm/i915: Do not rely on wm preservation for ILK watermarks
drm/i915: Cancel the modeset retry work during modeset cleanup
|
|
Pull block fixes from Jens Axboe:
"A few fixes that should go into this series:
- Regression fix for ide-cd, ensuring that a request is fully
initialized. From Hongxu.
- Ditto fix for virtio_blk, from Bart.
- NVMe fix from Keith, ensuring that we set the right block size on
revalidation. If the block size changed, we'd be in trouble without
it.
- NVMe rdma fix from Sagi, fixing a potential hang while the
controller is being removed"
* 'for-linus' of git://git.kernel.dk/linux-block:
ide:ide-cd: fix kernel panic resulting from missing scsi_req_init
nvme: Fix setting logical block format when revalidating
virtio_blk: Fix an SG_IO regression
nvme-rdma: fix possible hang when issuing commands during ctrl removal
|
|
In case the object has changed tiling between calls to execbuf, we need
to check if the existing offset inside the GTT matches the new tiling
constraint. We even need to do this for "unfenced" tiled objects, where
the 3D commands use an implied fence and so the object still needs to
match the physical fence restrictions on alignment (only required for
gen2 and early gen3).
In commit 2889caa92321 ("drm/i915: Eliminate lots of iterations over
the execobjects array"), the idea was to remove the second guessing and
only set the NEEDS_MAP flag when required. However, the entire check
for an unusable offset for fencing was removed and not just the
secondary check. I.e.
/* avoid costly ping-pong once a batch bo ended up non-mappable */
if (entry->flags & __EXEC_OBJECT_NEEDS_MAP &&
!i915_vma_is_map_and_fenceable(vma))
return !only_mappable_for_reloc(entry->flags);
was entirely removed as the ping-pong between execbuf passes was fixed,
but its primary purpose in forcing unaligned unfenced access to be
rebound was forgotten.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103502
Fixes: 2889caa92321 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031103607.17836-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit 1d033beb20d6d5885587a02a393b6598d766a382)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Pull networking fixes from David Miller:
1) Fix refcounting in xfrm_bundle_lookup() when using a dummy bundle,
from Steffen Klassert.
2) Fix crypto header handling in rx data frames in ath10k driver, from
Vasanthakumar Thiagarajan.
3) Fix use after free of qdisc when we defer tcp_chain_flush() to a
workqueue. From Cong Wang.
4) Fix double free in lapbether driver, from Pan Bian.
5) Sanitize TUNSETSNDBUF values, from Craig Gallek.
6) Fix refcounting when addrconf_permanent_addr() calls
ipv6_del_addr(). From Eric Dumazet.
7) Fix MTU probing bug in TCP that goes back to 2007, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
tcp: fix tcp_mtu_probe() vs highest_sack
ipv6: addrconf: increment ifp refcount before ipv6_del_addr()
tun/tap: sanitize TUNSETSNDBUF input
mlxsw: i2c: Fix buffer increment counter for write transaction
mlxsw: reg: Add high and low temperature thresholds
MAINTAINERS: Remove Yotam from mlxfw
MAINTAINERS: Update Yotam's E-mail
net: hns: set correct return value
net: lapbether: fix double free
bpf: remove SK_REDIRECT from UAPI
net: phy: marvell: Only configure RGMII delays when using RGMII
xfrm: Fix GSO for IPsec with GRE tunnel.
tc-testing: fix arg to ip command: -s -> -n
net_sched: remove tcf_block_put_deferred()
l2tp: hold tunnel in pppol2tp_connect()
Revert "ath10k: fix napi_poll budget overflow"
ath10k: rebuild crypto header in rx data frames
wcn36xx: Remove unnecessary rcu_read_unlock in wcn36xx_bss_info_changed
xfrm: Clear sk_dst_cache when applying per-socket policy.
xfrm: Fix xfrm_dst_cache memleak
|
|
Since we split the scsi_request out of struct request, while the
standard prep_rq_fn builds 10 byte cmds, it missed to invoke
scsi_req_init() to initialize certain fields of a scsi_request
structure (.__cmd[], .cmd, .cmd_len and .sense_len but no other
members of struct scsi_request).
An example panic on virtual machines (qemu/virtualbox) to boot
from IDE cdrom:
...
[ 8.754381] Call Trace:
[ 8.755419] blk_peek_request+0x182/0x2e0
[ 8.755863] blk_fetch_request+0x1c/0x40
[ 8.756148] ? ktime_get+0x40/0xa0
[ 8.756385] do_ide_request+0x37d/0x660
[ 8.756704] ? cfq_group_service_tree_add+0x98/0xc0
[ 8.757011] ? cfq_service_tree_add+0x1e5/0x2c0
[ 8.757313] ? ktime_get+0x40/0xa0
[ 8.757544] __blk_run_queue+0x3d/0x60
[ 8.757837] queue_unplugged+0x2f/0xc0
[ 8.758088] blk_flush_plug_list+0x1f4/0x240
[ 8.758362] blk_finish_plug+0x2c/0x40
...
[ 8.770906] RIP: ide_cdrom_prep_fn+0x63/0x180 RSP: ffff92aec018bae8
[ 8.772329] ---[ end trace 6408481e551a85c9 ]---
...
Fixes: 82ed4db499b8 ("block: split scsi_request out of struct request")
Signed-off-by: Hongxu Jia <hongxu.jia@windriver.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Just like the CTO timeout calculation introduced recently, the DTO
timeout calculation was incorrect. It used "bus_hz" but, as far as I
can tell, it's supposed to use the card clock. Let's account for the
div value, which is documented as 2x the value stored in the register,
or 1 if the register is 0.
NOTE: This was likely not terribly important until commit 16a34574c6ca
("mmc: dw_mmc: remove the quirks flags") landed because "DIV" is
documented on Rockchip SoCs (the ones that used to define the quirk)
to always be 0 or 1. ...and, in fact, it's documented to only be 1
with EMMC in 8-bit DDR52 mode. Thus before the quirk was applied to
everyone it was mostly OK to ignore the DIV value.
I haven't personally observed any problems that are fixed by this
patch but I also haven't tested this anywhere with a DIV other an 0.
AKA: this problem was found simply by code inspection and I have no
failing test cases that are fixed by it. Presumably this could fix
real bugs for someone out there, though.
Fixes: 16a34574c6ca ("mmc: dw_mmc: remove the quirks flags")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Syzkaller found several variants of the lockup below by setting negative
values with the TUNSETSNDBUF ioctl. This patch adds a sanity check
to both the tun and tap versions of this ioctl.
watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [repro:2389]
Modules linked in:
irq event stamp: 329692056
hardirqs last enabled at (329692055): [<ffffffff824b8381>] _raw_spin_unlock_irqrestore+0x31/0x75
hardirqs last disabled at (329692056): [<ffffffff824b9e58>] apic_timer_interrupt+0x98/0xb0
softirqs last enabled at (35659740): [<ffffffff824bc958>] __do_softirq+0x328/0x48c
softirqs last disabled at (35659731): [<ffffffff811c796c>] irq_exit+0xbc/0xd0
CPU: 0 PID: 2389 Comm: repro Not tainted 4.14.0-rc7 #23
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff880009452140 task.stack: ffff880006a20000
RIP: 0010:_raw_spin_lock_irqsave+0x11/0x80
RSP: 0018:ffff880006a27c50 EFLAGS: 00000282 ORIG_RAX: ffffffffffffff10
RAX: ffff880009ac68d0 RBX: ffff880006a27ce0 RCX: 0000000000000000
RDX: 0000000000000001 RSI: ffff880006a27ce0 RDI: ffff880009ac6900
RBP: ffff880006a27c60 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 000000000063ff00 R12: ffff880009ac6900
R13: ffff880006a27cf8 R14: 0000000000000001 R15: ffff880006a27cf8
FS: 00007f4be4838700(0000) GS:ffff88000cc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020101000 CR3: 0000000009616000 CR4: 00000000000006f0
Call Trace:
prepare_to_wait+0x26/0xc0
sock_alloc_send_pskb+0x14e/0x270
? remove_wait_queue+0x60/0x60
tun_get_user+0x2cc/0x19d0
? __tun_get+0x60/0x1b0
tun_chr_write_iter+0x57/0x86
__vfs_write+0x156/0x1e0
vfs_write+0xf7/0x230
SyS_write+0x57/0xd0
entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x7f4be4356df9
RSP: 002b:00007ffc18101c08 EFLAGS: 00000293 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f4be4356df9
RDX: 0000000000000046 RSI: 0000000020101000 RDI: 0000000000000005
RBP: 00007ffc18101c40 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000293 R12: 0000559c75f64780
R13: 00007ffc18101d30 R14: 0000000000000000 R15: 0000000000000000
Fixes: 33dccbb050bb ("tun: Limit amount of queued packets per device")
Fixes: 20d29d7a916a ("net: macvtap driver")
Signed-off-by: Craig Gallek <kraig@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It fixes a problem for the last chunk where 'chunk_size' is smaller than
MLXSW_I2C_BLK_MAX and data is copied to the wrong offset, overriding
previous data.
Fixes: 6882b0aee180 ("mlxsw: Introduce support for I2C bus")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ASIC has the ability to generate events whenever a sensor indicates
the temperature goes above or below its high or low thresholds,
respectively.
In new firmware versions the firmware enforces a minimum of 5
degrees Celsius difference between both thresholds. Make the driver
conform to this requirement.
Note that this is required even when the events are disabled, as in
certain systems interrupts are generated via GPIO based on these
thresholds.
Fixes: 85926f877040 ("mlxsw: reg: Add definition of temperature management registers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function of_parse_phandle() returns a NULL pointer if it cannot
resolve a phandle property to a device_node pointer. In function
hns_nic_dev_probe(), its return value is passed to PTR_ERR to extract
the error code. However, in this case, the extracted error code will
always be zero, which is unexpected.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
