| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Borislav Petkov:
"A totally boring branch this time around: a garden variety of small
fixes all over the place"
* tag 'edac_for_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/amd64: Do not warn when removing instances
EDAC/sifive: Fix return value check in ecc_register()
EDAC/aspeed: Remove unneeded semicolon
EDAC: remove set but not used variable 'ecc_loc'
EDAC: skx_common: downgrade message importance on missing PCI device
EDAC/Kconfig: Fix Kconfig indentation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"core:
- Add support for enable attributes to hwmon core
- Add intrusion templates
pmbus:
- Support for Infineon Multi-phase xdpe122 family controllers
- Support for Intel IMVP9 and AMD 6.25mV modes
- Support for vid mode detection per page bases
- Detect if chip is write protected
- Support for MAX20730, MAX20734, MAX20743, MAX20796, UCD90320,
TPS53688
- Various improvements to ibm-cffps driver
k10temp:
- Support for additional temperature sensors as well as voltage and
current telemetry for Zen CPUs
w83627ehf:
- Remove support for NCT6775, NCT6776 (they have their own driver)
New drivers:
- ADM1177
- MAX31730
- Driver for disk and solid state drives with temperature sensors
Other:
- pwm-fan: stop fan on shutdown"
* tag 'hwmon-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (35 commits)
hwmon: (k10temp) Display up to eight sets of CCD temperatures
hwmon: (k10temp) Add debugfs support
hwmon: (k10temp) Don't show temperature limits on Ryzen (Zen) CPUs
hwmon: (k10temp) Show core and SoC current and voltages on Ryzen CPUs
hwmon: (k10temp) Report temperatures per CPU die
hmon: (k10temp) Convert to use devm_hwmon_device_register_with_info
hwmon: (k10temp) Use bitops
hwmon: (pwm-fan) stop fan on shutdown
MAINTAINERS: add entry for ADM1177 driver
dt-binding: hwmon: Add documentation for ADM1177
hwmon: (adm1177) Add ADM1177 Hot Swap Controller and Digital Power Monitor driver
docs: hwmon: Include 'xdpe12284.rst' into docs
hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers
hwmon: (pmbus/tps53679) Extend device list supported by driver
hwmon: (pmbus/core) Add support for Intel IMVP9 and AMD 6.25mV modes
hwmon: (pmbus/core) Add support for vid mode detection per page bases
hwmon: (pmbus/ibm-cffps) Prevent writing on_off_config with bad data
hwmon: (w83627ehf) Remove set but not used variable 'fan4min'
hwmon: Driver for disk and solid state drives with temperature sensors
hwmon: (pmbus/ibm-cffps) Fix the LED behavior when turned off
...
|
|
Pull tpm updates from Jarkko Sakkinen:
"This adds a new sysfs file for querying TPM major version, which can
be used by the user space the TPM protocol used to communicate with
the chip"
* tag 'tpmdd-next-20200122' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm: Add tpm_version_major sysfs file
tpm: Update mailing list contact information in sysfs-class-tpm
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"The changes are a real mixed bag this time around.
The only scary looking one from the diffstat is the uapi change to
asm-generic/mman-common.h, but this has been acked by Arnd and is
actually just adding a pair of comments in an attempt to prevent
allocation of some PROT values which tend to get used for
arch-specific purposes. We'll be using them for Branch Target
Identification (a CFI-like hardening feature), which is currently
under review on the mailing list.
New architecture features:
- Support for Armv8.5 E0PD, which benefits KASLR in the same way as
KPTI but without the overhead. This allows KPTI to be disabled on
CPUs that are not affected by Meltdown, even is KASLR is enabled.
- Initial support for the Armv8.5 RNG instructions, which claim to
provide access to a high bandwidth, cryptographically secure
hardware random number generator. As well as exposing these to
userspace, we also use them as part of the KASLR seed and to seed
the crng once all CPUs have come online.
- Advertise a bunch of new instructions to userspace, including
support for Data Gathering Hint, Matrix Multiply and 16-bit
floating point.
Kexec:
- Cleanups in preparation for relocating with the MMU enabled
- Support for loading crash dump kernels with kexec_file_load()
Perf and PMU drivers:
- Cleanups and non-critical fixes for a couple of system PMU drivers
FPU-less (aka broken) CPU support:
- Considerable fixes to support CPUs without the FP/SIMD extensions,
including their presence in heterogeneous systems. Good luck
finding a 64-bit userspace that handles this.
Modern assembly function annotations:
- Start migrating our use of ENTRY() and ENDPROC() over to the
new-fangled SYM_{CODE,FUNC}_{START,END} macros, which are intended
to aid debuggers
Kbuild:
- Cleanup detection of LSE support in the assembler by introducing
'as-instr'
- Remove compressed Image files when building clean targets
IP checksumming:
- Implement optimised IPv4 checksumming routine when hardware offload
is not in use. An IPv6 version is in the works, pending testing.
Hardware errata:
- Work around Cortex-A55 erratum #1530923
Shadow call stack:
- Work around some issues with Clang's integrated assembler not
liking our perfectly reasonable assembly code
- Avoid allocating the X18 register, so that it can be used to hold
the shadow call stack pointer in future
ACPI:
- Fix ID count checking in IORT code. This may regress broken
firmware that happened to work with the old implementation, in
which case we'll have to revert it and try something else
- Fix DAIF corruption on return from GHES handler with pseudo-NMIs
Miscellaneous:
- Whitelist some CPUs that are unaffected by Spectre-v2
- Reduce frequency of ASID rollover when KPTI is compiled in but
inactive
- Reserve a couple of arch-specific PROT flags that are already used
by Sparc and PowerPC and are planned for later use with BTI on
arm64
- Preparatory cleanup of our entry assembly code in preparation for
moving more of it into C later on
- Refactoring and cleanup"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (73 commits)
arm64: acpi: fix DAIF manipulation with pNMI
arm64: kconfig: Fix alignment of E0PD help text
arm64: Use v8.5-RNG entropy for KASLR seed
arm64: Implement archrandom.h for ARMv8.5-RNG
arm64: kbuild: remove compressed images on 'make ARCH=arm64 (dist)clean'
arm64: entry: Avoid empty alternatives entries
arm64: Kconfig: select HAVE_FUTEX_CMPXCHG
arm64: csum: Fix pathological zero-length calls
arm64: entry: cleanup sp_el0 manipulation
arm64: entry: cleanup el0 svc handler naming
arm64: entry: mark all entry code as notrace
arm64: assembler: remove smp_dmb macro
arm64: assembler: remove inherit_daif macro
ACPI/IORT: Fix 'Number of IDs' handling in iort_id_map()
mm: Reserve asm-generic prot flags 0x10 and 0x20 for arch use
arm64: Use macros instead of hard-coded constants for MAIR_EL1
arm64: Add KRYO{3,4}XX CPU cores to spectre-v2 safe list
arm64: kernel: avoid x18 in __cpu_soft_restart
arm64: kvm: stop treating register x18 as caller save
arm64/lib: copy_page: avoid x18 register in assembler code
...
|
|
Pull block fix from Jens Axboe:
"Unfortunately this weekend we had a few last minute reports, one was
for block.
The partition disable for zoned devices was overly restrictive, it can
work (and be supported) just fine for host-aware variants.
Here's a fix ensuring that's the case so we don't break existing users
of that"
* tag 'block-5.5-2020-01-26' of git://git.kernel.dk/linux-block:
block: allow partitions on host aware zone devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two last minute fixes, both in drivers.
The fnic one is a highly unlikely condition, but the RDMA one is a
recently introduced regression that causes a kernel warning to trigger
in every RDMA logon, which would be unsightly if it got into the final
release"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: RDMA/isert: Fix a recently introduced regression related to logout
scsi: fnic: do not queue commands during fwreset
|
|
Host-aware SMR drives can be used with the commands to explicitly manage
zone state, but they can also be used as normal disks. In the former
case it makes perfect sense to allow partitions on them, in the latter
it does not, just like for host managed devices. Add a check to
add_partition to allow partitions on host aware devices, but give
up any zone management capabilities in that case, which also catches
the previously missed case of adding a partition vs just scanning it.
Because sd can rescan the attribute at runtime it needs to check if
a disk has partitions, for which a new helper is added to genhd.h.
Fixes: 5eac3eb30c9a ("block: Remove partition support for zoned block devices")
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull networking fixes from David Miller:
1) Off by one in mt76 airtime calculation, from Dan Carpenter.
2) Fix TLV fragment allocation loop condition in iwlwifi, from Luca
Coelho.
3) Don't confirm neigh entries when doing ipsec pmtu updates, from Xu
Wang.
4) More checks to make sure we only send TSO packets to lan78xx chips
that they can actually handle. From James Hughes.
5) Fix ip_tunnel namespace move, from William Dauchy.
6) Fix unintended packet reordering due to cooperation between
listification done by GRO and non-GRO paths. From Maxim
Mikityanskiy.
7) Add Jakub Kicincki formally as networking co-maintainer.
8) Info leak in airo ioctls, from Michael Ellerman.
9) IFLA_MTU attribute needs validation during rtnl_create_link(), from
Eric Dumazet.
10) Use after free during reload in mlxsw, from Ido Schimmel.
11) Dangling pointers are possible in tp->highest_sack, fix from Eric
Dumazet.
12) Missing *pos++ in various networking seq_next handlers, from Vasily
Averin.
13) CHELSIO_GET_MEM operation neds CAP_NET_ADMIN check, from Michael
Ellerman.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (109 commits)
firestream: fix memory leaks
net: cxgb3_main: Add CAP_NET_ADMIN check to CHELSIO_GET_MEM
net: bcmgenet: Use netif_tx_napi_add() for TX NAPI
tipc: change maintainer email address
net: stmmac: platform: fix probe for ACPI devices
net/mlx5e: kTLS, Do not send decrypted-marked SKBs via non-accel path
net/mlx5e: kTLS, Remove redundant posts in TX resync flow
net/mlx5e: kTLS, Fix corner-case checks in TX resync flow
net/mlx5e: Clear VF config when switching modes
net/mlx5: DR, use non preemptible call to get the current cpu number
net/mlx5: E-Switch, Prevent ingress rate configuration of uplink rep
net/mlx5: DR, Enable counter on non-fwd-dest objects
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Fix lowest FDB pool size
net: Fix skb->csum update in inet_proto_csum_replace16().
netfilter: nf_tables: autoload modules from the abort path
netfilter: nf_tables: add __nft_chain_type_get()
netfilter: nf_tables_offload: fix check the chain offload flag
netfilter: conntrack: sctp: use distinct states for new SCTP connections
ipv6_route_seq_next should increase position index
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A couple of fixes have come in that would be good to include in this
release:
- A fix for amount of memory on Beaglebone Black. Surfaced now since
GRUB2 doesn't update memory size in the booted kernel.
- A fix to make SPI interfaces work on am43x-epos-evm.
- Small Kconfig fix for OPTEE (adds a depend on MMU) to avoid build
failures"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1
tee: optee: Fix compilation issue with nommu
ARM: dts: am335x-boneblack-common: fix memory size
|
|
In fs_open(), 'vcc' is allocated through kmalloc() and assigned to
'atm_vcc->dev_data.' In the following execution, if an error occurs, e.g.,
there is no more free channel, an error code EBUSY or ENOMEM will be
returned. However, 'vcc' is not deallocated, leading to memory leaks. Note
that, in normal cases where fs_open() returns 0, 'vcc' will be deallocated
in fs_close(). But, if fs_open() fails, there is no guarantee that
fs_close() will be invoked.
To fix this issue, deallocate 'vcc' before the error code is returned.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fix from Linus Walleij:
"A single fix for the Intel Sunrisepoint pin controller that makes the
interrupts work properly on it"
* tag 'pinctrl-v5.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-01-24
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
Merge conflict: once merge with net-next, a contextual conflict will
appear in drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c
since the code moved in net-next.
To resolve, just delete ALL of the conflicting hunk from net.
So sorry for the small mess ..
For -stable v5.4:
('net/mlx5: Update the list of the PCI supported devices')
('net/mlx5: Fix lowest FDB pool size')
('net/mlx5e: kTLS, Fix corner-case checks in TX resync flow')
('net/mlx5e: kTLS, Do not send decrypted-marked SKBs via non-accel path')
('net/mlx5: Eswitch, Prevent ingress rate configuration of uplink rep')
('net/mlx5e: kTLS, Remove redundant posts in TX resync flow')
('net/mlx5: DR, Enable counter on non-fwd-dest objects')
('net/mlx5: DR, use non preemptible call to get the current cpu number')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cxgb3 driver for "Chelsio T3-based gigabit and 10Gb Ethernet
adapters" implements a custom ioctl as SIOCCHIOCTL/SIOCDEVPRIVATE in
cxgb_extension_ioctl().
One of the subcommands of the ioctl is CHELSIO_GET_MEM, which appears
to read memory directly out of the adapter and return it to userspace.
It's not entirely clear what the contents of the adapter memory
contains, but the assumption is that it shouldn't be accessible to all
users.
So add a CAP_NET_ADMIN check to the CHELSIO_GET_MEM case. Put it after
the is_offload() check, which matches two of the other subcommands in
the same function which also check for is_offload() and CAP_NET_ADMIN.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before commit 7587935cfa11 ("net: bcmgenet: move NAPI initialization to
ring initialization") moved the code, this used to be
netif_tx_napi_add(), but we lost that small semantic change in the
process, restore that.
Fixes: 7587935cfa11 ("net: bcmgenet: move NAPI initialization to ring initialization")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use generic device API to get phy mode to fix probe failure
with ACPI based devices.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- add sanity checks to USB endpoints in various dirvers
- max77650-onkey was missing an OF table which was preventing module
autoloading
- a revert and a different fix for F54 handling in Synaptics dirver
- a fixup for handling register in pm8xxx vibrator driver
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: pm8xxx-vib - fix handling of separate enable register
Input: keyspan-remote - fix control-message timeouts
Input: max77650-onkey - add of_match table
Input: rmi_f54 - read from FIFO in 32 byte blocks
Revert "Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers"
Input: sur40 - fix interface sanity checks
Input: gtco - drop redundant variable reinit
Input: gtco - fix extra-descriptor debug message
Input: gtco - fix endpoint sanity check
Input: aiptek - use descriptors of current altsetting
Input: aiptek - fix endpoint sanity check
Input: pegasus_notetaker - fix endpoint sanity check
Input: sun4i-ts - add a check for devm_thermal_zone_of_sensor_register
Input: evdev - convert kzalloc()/vzalloc() to kvzalloc()
|
|
https://git.linaro.org:/people/jens.wiklander/linux-tee into arm/fixes
Fix OP-TEE compile error with nommu
* tag 'tee-optee-fix2-for-5.5' of https://git.linaro.org:/people/jens.wiklander/linux-tee:
tee: optee: Fix compilation issue with nommu
Link: https://lore.kernel.org/r/20200123101310.GA10320@jax
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
When TCP out-of-order is identified (unexpected tcp seq mismatch), driver
analyzes the packet and decides what handling should it get:
1. go to accelerated path (to be encrypted in HW),
2. go to regular xmit path (send w/o encryption),
3. drop.
Packets marked with skb->decrypted by the TLS stack in the TX flow skips
SW encryption, and rely on the HW offload.
Verify that such packets are never sent un-encrypted on the wire.
Add a WARN to catch such bugs, and prefer dropping the packet in these cases.
Fixes: 46a3ea98074e ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The call to tx_post_resync_params() is done earlier in the flow,
the post of the control WQEs is unnecessarily repeated. Remove it.
Fixes: 700ec4974240 ("net/mlx5e: kTLS, Fix missing SQ edge fill")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
There are the following cases:
1. Packet ends before start marker: bypass offload.
2. Packet starts before start marker and ends after it: drop,
not supported, breaks contract with kernel.
3. packet ends before tls record info starts: drop,
this packet was already acknowledged and its record info
was released.
Add the above as comment in code.
Mind possible wraparounds of the TCP seq, replace the simple comparison
with a call to the TCP before() method.
In addition, remove logic that handles negative sync_len values,
as it became impossible.
Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Fixes: 46a3ea98074e ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently VF in LEGACY mode are not able to go up. Also in OFFLOADS
mode, when switching to it first time, VF can go up independently to
his representor, which is not expected.
Perform clearing of VF config when switching modes and set link state
to AUTO as default value. Also, when switching to OFFLOADS mode set
link state to DOWN, which allow VF link state to be controlled by its
REP.
Fixes: 1ab2068a4c66 ("net/mlx5: Implement vports admin state backup/restore")
Fixes: 556b9d16d3f5 ("net/mlx5: Clear VF's configuration on disabling SRIOV")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use raw_smp_processor_id instead of smp_processor_id() otherwise we will
get the following trace in debug-kernel:
BUG: using smp_processor_id() in preemptible [00000000] code: devlink
caller is dr_create_cq.constprop.2+0x31d/0x970 [mlx5_core]
Call Trace:
dump_stack+0x9a/0xf0
debug_smp_processor_id+0x1f3/0x200
dr_create_cq.constprop.2+0x31d/0x970
genl_family_rcv_msg+0x5fd/0x1170
genl_rcv_msg+0xb8/0x160
netlink_rcv_skb+0x11e/0x340
Fixes: 297cccebdc5a ("net/mlx5: DR, Expose an internal API to issue RDMA operations")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Since the implementation relies on limiting the VF transmit rate to
simulate ingress rate limiting, and since either uplink representor or
ecpf are not associated with a VF, we limit the rate limit configuration
for those ports.
Fixes: fcb64c0f5640 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The current code handles only counters that attached to dest, we still
have the cases where we have counter on non-dest, like over drop etc.
Fixes: 6a48faeeca10 ("net/mlx5: Add direct rule fs_cmd implementation")
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add the upcoming ConnectX-7 device ID.
Fixes: 85327a9c4150 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The pool sizes represent the pool sizes in the fw. when we request
a pool size from fw, it will return the next possible group.
We track how many pools the fw has left and start requesting groups
from the big to the small.
When we start request 4k group, which doesn't exists in fw, fw
wants to allocate the next possible size, 64k, but will fail since
its exhausted. The correct smallest pool size in fw is 128 and not 4k.
Fixes: e52c28024008 ("net/mlx5: E-Switch, Add chains and priorities")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Two fixes:
- Fix NULL-ptr dereference bug in Intel IOMMU driver
- Properly save and restore AMD IOMMU performance counter registers
when testing if they are writable"
* tag 'iommu-fixes-v5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix IOMMU perf counter clobbering during init
iommu/vt-d: Call __dmar_remove_one_dev_info with valid pointer
|
|
Pull drm fixes from Dave Airlie:
"This one has a core mst fix and two i915 fixes. amdgpu just enables
some hw outside experimental.
The panfrost fix is a little bigger than I'd like at this stage but it
fixes a fairly fundamental problem with global shared buffers in that
driver, and since it's confined to that driver and I've taken a look
at it, I think it's fine to get into the tree now, so it can get
stable propagated as well.
core/mst:
- Fix SST branch device handling
amdgpu:
- enable renoir outside experimental
i915:
- Avoid overflow with huge userptr objects
- uAPI fix to correctly handle negative values in
engine->uabi_class/instance (cc: stable)
panfrost:
- Fix mapping of globally visible BO's (Boris)"
* tag 'drm-fixes-2020-01-24' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: remove the experimental flag for renoir
drm/panfrost: Add the panfrost_gem_mapping concept
drm/i915: Align engine->uabi_class/instance with i915_drm.h
drm/i915/userptr: fix size calculation
drm/dp_mst: Handle SST-only branch device case
|
|
init_iommu_perf_ctr() clobbers the register when it checks write access
to IOMMU perf counters and fails to restore when they are writable.
Add save and restore to fix it.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Fixes: 30861ddc9cca4 ("perf/x86/amd: Add IOMMU Performance Counter resource management")
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
It is possible for archdata.iommu to be set to
DEFER_DEVICE_DOMAIN_INFO or DUMMY_DEVICE_DOMAIN_INFO so check for
those values before calling __dmar_remove_one_dev_info. Without a
check it can result in a null pointer dereference. This has been seen
while booting a kdump kernel on an HP dl380 gen9.
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: stable@vger.kernel.org # 5.3+
Cc: linux-kernel@vger.kernel.org
Fixes: ae23bfb68f28 ("iommu/vt-d: Detach domain before using a private one")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a hw_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC host fixes:
- sdhci: Fix minimum clock rate for v3 controllers
- sdhci-tegra: Fix SDR50 tuning override
- sdhci_am654: Fixup tuning issues and support for CQHCI
- sdhci_am654: Remove wrong write protect flag"
* tag 'mmc-v5.5-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci: fix minimum clock rate for v3 controller
mmc: tegra: fix SDR50 tuning override
mmc: sdhci_am654: Fix Command Queuing in AM65x
mmc: sdhci_am654: Reset Command and Data line after tuning
mmc: sdhci_am654: Remove Inverted Write Protect flag
|
|
In HWiNFO, we see support for Tccd1, Tccd3, Tccd5, and Tccd7 temperature
sensors on Zen2 based Threadripper CPUs. Checking register maps on
Threadripper 3970X confirms SMN register addresses and values for those
sensors.
Register values observed in an idle system:
0x059950: 00000000 00000abc 00000000 00000ad8
0x059960: 00000000 00000ade 00000000 00000ae4
Under load:
0x059950: 00000000 00000c02 00000000 00000c14
0x059960: 00000000 00000c30 00000000 00000c22
More analysis shows that EPYC CPUs support up to 8 CCD temperature
sensors. EPYC 7601 supports three CCD temperature sensors. Unlike
Zen2 CPUs, the register space in Zen1 CPUs supports a maximum of four
sensors, so only search for a maximum of four sensors on Zen1 CPUs.
On top of that, in thm_10_0_sh_mask.h in the Linux kernel, we find
definitions for THM_DIE{1-3}_TEMP__VALID_MASK, set to 0x00000800, as well
as matching SMN addresses. This lets us conclude that bit 11 of the
respective registers is a valid bit. With this assumption, the temperature
offset is now 49 degrees C. This conveniently matches the documented
temperature offset for Tdie, again suggesting that above registers indeed
report temperatures sensor values. Assume that bit 11 is indeed a valid
bit, and add support for the additional sensors.
With this patch applied, output from 3970X (idle) looks as follows:
k10temp-pci-00c3
Adapter: PCI adapter
Tdie: +55.9°C
Tctl: +55.9°C
Tccd1: +39.8°C
Tccd3: +43.8°C
Tccd5: +43.8°C
Tccd7: +44.8°C
Tested-by: Michael Larabel <michael@phoronix.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
amd-drm-fixes-5.5-2020-01-23:
amdgpu:
- remove the experimental flag from renoir
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123191424.3849-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Avoid overflow with huge userptr objects
- uAPI fix to correctly handle negative values in
engine->uabi_class/instance (cc: stable)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123135045.GA12584@jlahtine-desk.ger.corp.intel.com
|
|
Show thermal and SVI registers for Family 17h CPUs.
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The maximum Tdie or Tctl is not published for Ryzen CPUs. What is
known, however, is that the traditional value of 70 degrees C is no
longer correct. On top of that, the limit applies to Tctl, not to Tdie.
Displaying it in either context is meaningless, confusing, and wrong.
Stop doing it.
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Ryzen CPUs report core and SoC voltages and currents. Add support
for it to the k10temp driver.
For the time being, only report voltages and currents for Ryzen
CPUs. Threadripper and EPYC appear to use a different mechanism.
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Bernhard Gebetsberger <bernhard.gebetsberger@gmx.at>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Tested-by: Darren Salt <devspam@moreofthesa.me.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Zen2 reports reporting temperatures per CPU die (called Core Complex Dies,
or CCD, by AMD). Add support for it to the k10temp driver.
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Bernhard Gebetsberger <bernhard.gebetsberger@gmx.at>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Tested-by: Darren Salt <devspam@moreofthesa.me.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Convert driver to use devm_hwmon_device_register_with_info to simplify
the code and to reduce its size.
Old size (x86_64):
text data bss dec hex filename
8247 4488 64 12799 31ff drivers/hwmon/k10temp.o
New size:
text data bss dec hex filename
6778 2792 64 9634 25a2 drivers/hwmon/k10temp.o
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Bernhard Gebetsberger <bernhard.gebetsberger@gmx.at>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Tested-by: Darren Salt <devspam@moreofthesa.me.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Using bitops makes bit masks and shifts easier to read.
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Tested-by: Bernhard Gebetsberger <bernhard.gebetsberger@gmx.at>
Tested-by: Holger Kiehl <holger.kiehl@dwd.de>
Tested-by: Michael Larabel <michael@phoronix.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Ken Moffat <zarniwhoop73@googlemail.com>
Tested-by: Darren Salt <devspam@moreofthesa.me.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The pwm-fan driver stops the fan in suspend but leaves the fan on in
shutdown. It seems strange to leave the fan on in shutdown because there
is no use case in my mind and the gpio-fan driver on the other hand stops
in shutdown.
This change turns off the fan in shutdown. If anyone complains then we'll
add an optional property to switch the behavior.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kamil Debski <kamil@wypas.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Link: https://lore.kernel.org/r/1579534344-11694-1-git-send-email-akinobu.mita@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
driver
ADM1177 is a Hot Swap Controller and Digital Power Monitor with
Soft Start Pin.
Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Link: https://lore.kernel.org/r/20200114112159.25998-1-beniamin.bia@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for devices XDPE12254, XDPE12284.
All these device support two pages.
The below lists of VOUT_MODE command readout with their related VID
protocols, Digital to Analog Converter steps, supported by these
devices:
VR12.0 mode, 5-mV DAC - 0x01;
VR12.5 mode, 10-mV DAC - 0x02;
IMVP9 mode, 5-mV DAC - 0x03;
AMD mode 6.25mV - 0x10.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-5-vadimp@mellanox.com
[groeck: Added missing break statement]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Extends driver with support of the additional devices:
Texas Instruments Dual channel DCAP+ multiphase controllers: TPS53688.
Extend Kconfig with added device.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-4-vadimp@mellanox.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Extend "vrm_version" with the type for Intel IMVP9 and AMD 6.25mV VID
modes.
Add calculation for those types.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-3-vadimp@mellanox.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for VID protocol detection per page bases, instead of
detecting it based on "PMBU_VOUT" readout from page 0 for all the pages
supported by particular device.
The reason that some devices allows to configure different VID modes
per page within the same device.
Patch modifies the field "vrm_version" within the structure
"pmbus_driver_info" to be per page array.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-2-vadimp@mellanox.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
If the user write parameters resulted in no bytes being written to the
temporary buffer, then ON_OFF_CONFIG will be written with uninitialized
data. Prevent this by bailing out in this case.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1578411640-16929-1-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
