| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
|
|
This adds a compatible for the high speed UARTs on the StarFive JH7100
RISC-V SoC. Just like the regular uarts we also need to keep the input
clocks at their default rate and rely only on the divisor in the UART.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
|
|
Drop the unnecessary "_sys" infix from the suspend PM ops.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-10-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial drivers should not be dropping characters themselves, but at
least drop the unused 'drop' parameter from the receive handler for now.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop the unnecessary WARN() in case the TTY buffers are ever full in
favour of a rate limited dev_err() which doesn't kill the machine when
panic_on_warn is set.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-8-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The receiver is supposed to be enabled in the startup() callback and not
in set_termios() which is called also during console setup.
This specifically avoids accepting input before the port has been opened
(and interrupts enabled), something which can also break the GENI
firmware (cancel fails and after abort, the "stale" counter handling
appears to be broken so that later input is not processed until twelve
chars have been received).
There also does not appear to be any need to keep the receiver disabled
while updating the port settings.
Since commit 6f3c3cafb115 ("serial: qcom-geni: disable interrupts during
console writes") the calls to manipulate the secondary interrupts, which
were done without holding the port lock, can also lead to the receiver
being left disabled when set_termios() races with the console code (e.g.
when init opens the tty during boot). This can manifest itself as a
serial getty not accepting input.
The calls to stop and start rx in set_termios() can similarly race with
DMA completion and, for example, cause the DMA buffer to be unmapped
twice or the mapping to be leaked.
Fix this by only enabling the receiver during startup and while holding
the port lock to avoid racing with the console code.
Fixes: 6f3c3cafb115 ("serial: qcom-geni: disable interrupts during console writes")
Fixes: 2aaa43c70778 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 6.3
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to wait for the DMA transfer to complete when cancelling the
rx command on stop_rx(). This specifically prevents the DMA completion
interrupt from firing after rx has been restarted, something which can
lead to an IOMMU fault and hosed rx when the interrupt handler unmaps
the DMA buffer for the new command:
qcom_geni_serial 988000.serial: serial engine reports 0 RX bytes in!
arm-smmu 15000000.iommu: FSR = 00000402 [Format=2 TF], SID=0x563
arm-smmu 15000000.iommu: FSYNR0 = 00210013 [S1CBNDX=33 WNR PLVL=3]
Bluetooth: hci0: command 0xfc00 tx timeout
Bluetooth: hci0: Reading QCA version information failed (-110)
Also add the missing state machine reset which is needed in case
cancellation fails.
Fixes: 2aaa43c70778 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable@vger.kernel.org # 6.3
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A commit adding back the stopping of tx on port shutdown failed to add
back the locking which had also been removed by commit e83766334f96
("tty: serial: qcom_geni_serial: No need to stop tx/rx on UART
shutdown").
Holding the port lock is needed to serialise against the console code,
which may update the interrupt enable register and access the port
state.
Fixes: d8aca2f96813 ("tty: serial: qcom-geni-serial: stop operations in progress at shutdown")
Fixes: 947cc4ecc06c ("serial: qcom-geni: fix soft lockup on sw flow control and suspend")
Cc: stable@vger.kernel.org # 6.3
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 35781d8356a2eecaa6074ceeb80ee22e252fcdae.
Hibernation is not supported on Qualcomm platforms with mainline
kernels yet a broken vendor implementation for the GENI serial driver
made it upstream.
This is effectively dead code that cannot be tested and should just be
removed, but if these paths were ever hit for an open non-console port
they would crash the machine as the driver would fail to enable clocks
during restore() (i.e. all ports would have to be closed by drivers and
user space before hibernating the system to avoid this as a comment in
the code hinted at).
The broken implementation also added a random call to enable the
receiver in the port setup code where it does not belong and which
enables the receiver prematurely for console ports.
Fixes: 35781d8356a2 ("tty: serial: qcom-geni-serial: Add support for Hibernation feature")
Cc: stable@vger.kernel.org # 6.2
Cc: Aniket Randive <quic_arandive@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The polled console (KGDB/KDB) implementation must not call port setup
unconditionally as the port may already be in use by the console or a
getty.
Only make sure that the receiver is enabled, but do not enable any
device interrupts.
Fixes: d8851a96ba25 ("tty: serial: qcom-geni-serial: Add a poll_init() function")
Cc: stable@vger.kernel.org # 6.4
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When sending data using DMA at high baudrate (4 Mbdps in local test case) to
a device with small RX buffer which keeps asserting RTS after every received
byte, it is possible that the iMX UART driver would not recognize the falling
edge of RTS input signal and get stuck, unable to transmit any more data.
This condition happens when the following sequence of events occur:
- imx_uart_mctrl_check() is called at some point and takes a snapshot of UART
control signal status into sport->old_status using imx_uart_get_hwmctrl().
The RTSS/TIOCM_CTS bit is of interest here (*).
- DMA transfer occurs, the remote device asserts RTS signal after each byte.
The i.MX UART driver recognizes each such RTS signal change, raises an
interrupt with USR1 register RTSD bit set, which leads to invocation of
__imx_uart_rtsint(), which calls uart_handle_cts_change().
- If the RTS signal is deasserted, uart_handle_cts_change() clears
port->hw_stopped and unblocks the port for further data transfers.
- If the RTS is asserted, uart_handle_cts_change() sets port->hw_stopped
and blocks the port for further data transfers. This may occur as the
last interrupt of a transfer, which means port->hw_stopped remains set
and the port remains blocked (**).
- Any further data transfer attempts will trigger imx_uart_mctrl_check(),
which will read current status of UART control signals by calling
imx_uart_get_hwmctrl() (***) and compare it with sport->old_status .
- If current status differs from sport->old_status for RTS signal,
uart_handle_cts_change() is called and possibly unblocks the port
by clearing port->hw_stopped .
- If current status does not differ from sport->old_status for RTS
signal, no action occurs. This may occur in case prior snapshot (*)
was taken before any transfer so the RTS is deasserted, current
snapshot (***) was taken after a transfer and therefore RTS is
deasserted again, which means current status and sport->old_status
are identical. In case (**) triggered when RTS got asserted, and
made port->hw_stopped set, the port->hw_stopped will remain set
because no change on RTS line is recognized by this driver and
uart_handle_cts_change() is not called from here to unblock the
port->hw_stopped.
Update sport->old_status in __imx_uart_rtsint() accordingly to make
imx_uart_mctrl_check() detect such RTS change. Note that TIOCM_CAR
and TIOCM_RI bits in sport->old_status do not suffer from this problem.
Fixes: ceca629e0b48 ("[ARM] 2971/1: i.MX uart handle rts irq")
Cc: stable <stable@kernel.org>
Reviewed-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20241002184133.19427-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup
of the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART
engine that that chip seems to have. Hopefully it's in a better
state now, but hardware designers still seem to come up with more
ways to make broken UARTS 40+ years after this all should have
finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems"
* tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: samsung: Fix serial rx on Apple A7-A9
tty: serial: samsung: Fix A7-A11 serial earlycon SError
tty: serial: samsung: Use bit manipulation macros for APPLE_S5L_*
tty: rp2: Fix reset with non forgiving PCIe host bridges
serial: 8250_aspeed_vuart: Enable module autoloading
serial: qcom-geni: fix polled console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix console corruption
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix fifo polling timeout
tty: hvc: convert comma to semicolon
mxser: convert comma to semicolon
serial: 8250_bcm2835aux: Fix clock imbalance in PM resume
serial: sc16is7xx: convert bitmask definitions to use BIT() macro
serial: sc16is7xx: fix copy-paste errors in EFR_SWFLOWx_BIT constants
serial: sc16is7xx: remove SC16IS7XX_MSR_DELTA_MASK
serial: xilinx_uartps: Make cdns_rs485_supported static
...
|
|
Apple's older A7-A9 SoCs seems to use bit 3 in UTRSTAT as RXTO, which is
enabled by bit 11 in UCON.
Access these bits in addition to the original RXTO and RXTO enable bits,
to allow serial rx to function on A7-A9 SoCs. This change does not
appear to affect the A10 SoC and up.
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Nick Chan <towinchenmi@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20240911050741.14477-4-towinchenmi@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Apple's earlier SoCs, like A7-A11, requires 32-bit writes for the serial
port. Otherwise, a SError happens when writing to UTXH (+0x20). This only
manifested in earlycon as reg-io-width in the device tree is consulted
for normal serial writes.
Change the iotype of the port to UPIO_MEM32, to allow the serial port to
function on A7-A11 SoCs. This change does not appear to affect Apple M1 and
above.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Tested-by: Janne Grunau <j@jannau.net>
Signed-off-by: Nick Chan <towinchenmi@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20240911050741.14477-3-towinchenmi@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The write to RP2_GLOBAL_CMD followed by an immediate read of
RP2_GLOBAL_CMD in rp2_reset_asic() is intented to flush out the write,
however by then the device is already in reset and cannot respond to a
memory cycle access.
On platforms such as the Raspberry Pi 4 and others using the
pcie-brcmstb.c driver, any memory access to a device that cannot respond
is met with a fatal system error, rather than being substituted with all
1s as is usually the case on PC platforms.
Swapping the delay and the read ensures that the device has finished
resetting before we attempt to read from it.
Fixes: 7d9f49afa451 ("serial: rp2: New driver for Comtrol RocketPort 2 cards")
Cc: stable <stable@kernel.org>
Suggested-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240906225435.707837-1-florian.fainelli@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240903131503.961178-1-liaochen4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The polled UART operations are used by the kernel debugger (KDB, KGDB),
which can interrupt the kernel at any point in time. The current
Qualcomm GENI implementation does not really work when there is on-going
serial output as it inadvertently "hijacks" the current tx command,
which can result in both the initial debugger output being corrupted as
well as the corruption of any on-going serial output (up to 4k
characters) when execution resumes:
0190: abcdefghijklmnopqrstuvwxyz0123456789 0190: abcdefghijklmnopqrstuvwxyz0123456789
0191: abcdefghijklmnop[ 50.825552] sysrq: DEBUG
qrstuvwxyz0123456789 0191: abcdefghijklmnopqrstuvwxyz0123456789
Entering kdb (current=0xffff53510b4cd280, pid 640) on processor 2 due to Keyboard Entry
[2]kdb> go
omlji3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t72r2rp
o9n976k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawavu:t7t8s8s8r2r2q0q0p
o9n9n8ml6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav v u:u:t9t0s4s4rq0p
o9n9n8m8m7l7l6k6k5j5j40q0p p o
o9n9n8m8m7l7l6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t8t9s4s4r4r4q0q0p
Fix this by making sure that the polled output implementation waits for
the tx fifo to drain before cancelling any on-going longer transfers. As
the polled code cannot take any locks, leave the state variables as they
are and instead make sure that the interrupt handler always starts a new
tx command when there is data in the write buffer.
Since the debugger can interrupt the interrupt handler when it is
writing data to the tx fifo, it is currently not possible to fully
prevent losing up to 64 bytes of tty output on resume.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 4.17
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Disable the GENI interrupts during console writes to reduce the risk of
having interrupt handlers spinning on the port lock on other cores for
extended periods of time.
This can, for example, reduce the total amount of time spent in the
interrupt handler during boot of the x1e80100 CRD by up to a factor nine
(e.g. from 274 ms to 30 ms) while the worst case processing time drops
from 19 ms to 8 ms.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-8-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Qualcomm serial console implementation is broken and can lose
characters when the serial port is also used for tty output.
Specifically, the console code only waits for the current tx command to
complete when all data has already been written to the fifo. When there
are on-going longer transfers this often means that console output is
lost when the console code inadvertently "hijacks" the current tx
command instead of starting a new one.
This can, for example, be observed during boot when console output that
should have been interspersed with init output is truncated:
[ 9.462317] qcom-snps-eusb2-hsphy fde000.phy: Registered Qcom-eUSB2 phy
[ OK ] Found device KBG50ZNS256G KIOXIA Wi[ 9.471743ndows.
[ 9.539915] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
Add a new state variable to track how much data has been written to the
fifo and use it to determine when the fifo and shift register are both
empty. This is needed since there is currently no other known way to
determine when the shift register is empty.
This in turn allows the console code to interrupt long transfers without
losing data.
Note that the oops-in-progress case is similarly broken as it does not
cancel any active command and also waits for the wrong status flag when
attempting to drain the fifo (TX_FIFO_NOT_EMPTY_EN is only set when
cancelling a command leaves data in the fifo).
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Fixes: a1fee899e5be ("tty: serial: qcom_geni_serial: Fix softlock")
Fixes: 9e957a155005 ("serial: qcom-geni: Don't cancel/abort if we can't get the port lock")
Cc: stable@vger.kernel.org # 4.17
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-7-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With a small modification the qcom_geni_serial_poll_bit() function
could be used to poll more than just a single bit. Let's generalize
it. We'll make the qcom_geni_serial_poll_bit() into just a wrapper of
the general function.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240610152420.v4.5.Ic6411eab8d9d37acc451705f583fb535cd6dadb2@changeid
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The "offset" passed in should be unsigned since it's always a positive
offset from our memory mapped IO.
The "field" should be u32 since we're anding it with a 32-bit value
read from the device.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240610152420.v4.4.I24a0de52dd7336908df180fa6b698e001f3aff82@changeid
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 663abb1a7a7f ("tty: serial: qcom_geni_serial: Fix UART hang")
addressed an issue with stalled tx after the console code interrupted
the last bytes of a tx command by reenabling the watermark interrupt if
there is data in write buffer. This can however break software flow
control by re-enabling tx after the user has stopped it.
Address the original issue by not clearing the CMD_DONE flag after
polling for command completion. This allows the interrupt handler to
start another transfer when the CMD_DONE interrupt has not been disabled
due to flow control.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Fixes: 663abb1a7a7f ("tty: serial: qcom_geni_serial: Fix UART hang")
Cc: stable@vger.kernel.org # 4.17
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The qcom_geni_serial_poll_bit() can be used to wait for events like
command completion and is supposed to wait for the time it takes to
clear a full fifo before timing out.
As noted by Doug, the current implementation does not account for start,
stop and parity bits when determining the timeout. The helper also does
not currently account for the shift register and the two-word
intermediate transfer register.
A too short timeout can specifically lead to lost characters when
waiting for a transfer to complete as the transfer is cancelled on
timeout.
Instead of determining the poll timeout on every call, store the fifo
timeout when updating it in set_termios() and make sure to take the
shift and intermediate registers into account. Note that serial core has
already added a 20 ms margin to the fifo timeout.
Also note that the current uart_fifo_timeout() interface does
unnecessary calculations on every call and did not exist in earlier
kernels so only store its result once. This facilitates backports too as
earlier kernels can derive the timeout from uport->timeout, which has
since been removed.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 4.17
Reported-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During review Ulf Hansson discovered a clock imbalance in the recently
introduced PM resume code. The driver should enable the clock only in
case it has been disabled in suspend before. In order to make the
conditions easier to read, refactor this into a separate function.
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Closes: https://lore.kernel.org/linux-arm-kernel/CAPDyKFoJh3j8xSeXZ9o031YZLTCDYVA+dgvURuwozjDpU_aauA@mail.gmail.com/
Fixes: 0e1d8780526f ("serial: 8250_bcm2835aux: add PM suspend/resume support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20240818174936.88372-1-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that bit definition comments were cleaned up, convert bitmask
definitions to use BIT() macro for clarity.
Convert SC16IS7XX_IIR_ID_MASK to use GENMASK() macro -
- while at that, realign comments.
Compose SC16IS7XX_LSR_BRK_ERROR_MASK using aforementioned constants,
instead of open-coding it, and remove now unneeded comments.
Signed-off-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/8b45a01e-7cc5-4d53-b467-c6680bc51ef4@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Comments attached to bits 0 and 1 incorrectly referenced bits 2 and 3,
which don't match the datasheet - fix them.
At the same time remove comments for individual constants, as they add
nothing to the definitions themselves.
Signed-off-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/2986a485-935d-4ab2-9a16-4a85288aa15a@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This definition isn't used anywhere anymore, let's delete it.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/91a9aa22-47b7-449a-a7ad-877ce1b6402e@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sparse tool complains as follows:
drivers/tty/serial/xilinx_uartps.c:222:21: warning:
symbol 'cdns_rs485_supported' was not declared. Should it be static?
This symbol is not used outside xilinx_uartps.c, so marks it static.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20240819120107.3884973-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce uart_port_set_cons() as a wrapper to set @cons of a
uart_port. The wrapper sets @cons under the port lock in order
to prevent @cons from disappearing while another context is
holding the port lock. This is necessary for a follow-up
commit relating to the port lock wrappers, which rely on @cons
not changing between lock and unlock.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Tested-by: Théo Lebrun <theo.lebrun@bootlin.com> # EyeQ5, AMBA-PL011
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240820063001.36405-12-john.ogness@linutronix.de
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
suspend"
This reverts commit 68e6939ea9ec3d6579eadeab16060339cdeaf940.
Kevin reported that this causes a crash during suspend on platforms that
dont use PM domains.
Link: https://lore.kernel.org/r/7ha5hgpchq.fsf@baylibre.com
Cc: Thomas Richard <thomas.richard@bootlin.com>
Fixes: 68e6939ea9ec ("serial: 8250_omap: Set the console genpd always on if no console suspend")
Cc: stable <stable@kernel.org>
Reported-by: Kevin Hilman <khilman@kernel.org>
Signed-off-by: Griffin Kroah-Hartman <griffin@kroah.com>
Link: https://lore.kernel.org/r/20240814111747.82371-1-griffin@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Guards can help to make the code more readable. So use it wherever they
do so.
On many places labels and 'ret' locals are eliminated completely.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240808103549.429349-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The definition of the PM operations opens code the existing macro,
replace it with the DEFINE_SIMPLE_DEV_PM_OPS() for setting the driver's
PM routines.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240813081954.1408792-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unify comment style and fix indentation in some cases.
While at it, add that it supports ACPI enumerated non-PNP devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240812154901.1068407-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make it clear that it supports two cases, pure platform device and ACPI.
With this in mind, split serial8250_probe() to two functions and rename
the ACPI case accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240812154901.1068407-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Switch to use new platform_get_mem_or_io() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240812154901.1068407-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Tidy up ACPI ID table:
- remove explicit driver_data initializer
- drop comma in the terminator entry
- use C comment style
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240812154901.1068407-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use has_acpi_companion() as 8250_core does to unify this across
the driver modules.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240812154901.1068407-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't shadow error from serial8250_register_8250_port() and return it as is.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240812154901.1068407-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UPF_IOREMAP is for serial core to map the resource on behalf of the
driver. No need to perform this explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240812154901.1068407-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the wakeup-source property is present, enable wakeup from this
device.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20240807141227.1093006-6-msp@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver sets wakeup enable by default. But not all UARTs are meant to
be wakeup enabled. Change the default to be wakeup capable but not
enabled. The user can enable wakeup when needed.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20240807141227.1093006-5-msp@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If devm_request_irq fails, the code does not cleanup many things that
were setup before. Instead of directly returning ret we should jump to
err.
Fixes: fef4f600319e ("serial: 8250: omap: Fix life cycle issues for interrupt handlers")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20240807141227.1093006-4-msp@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This field seems to be unused for quite some time already. Remove it.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20240807141227.1093006-3-msp@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The interrupt handler routines and helpers are casting the 'void *'
pointer to 'struct exynos_uart_port *' all over the place.
There is no need for that, we can do the casting once and keep passing
the 'struct exynos_uart_port *', simplifying the code and saving a few
lines of code.
No functional changes.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240808-samsung-tty-cleanup-v3-2-494412f49f4b@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 'irq' argument is not used in any of the callees, we can just drop
it and simplify the code.
No functional changes.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240808-samsung-tty-cleanup-v3-1-494412f49f4b@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In RS485 mode, the RTS pin is driven high by hardware when the transmitter
is operating. This behaviour cannot be changed. This means that the driver
should claim that it supports SER_RS485_RTS_ON_SEND and not
SER_RS485_RTS_AFTER_SEND.
Otherwise, when configuring the port with the SER_RS485_RTS_ON_SEND, one
get the following warning:
kern.warning kernel: atmel_usart_serial atmel_usart_serial.2.auto:
ttyS1 (1): invalid RTS setting, using RTS_AFTER_SEND instead
which is contradictory with what's really happening.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Cc: stable <stable@kernel.org>
Tested-by: Alexander Dahl <ada@thorsis.com>
Fixes: af47c491e3c7 ("serial: atmel: Fill in rs485_supported")
Link: https://lore.kernel.org/r/20240808060637.19886-1-othacehe@gnu.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With "earlycon initcall_debug=1 loglevel=8" in bootargs, kernel
sometimes boot hang. It is because normal console still is not ready,
but runtime suspend is called, so early console putchar will hang
in waiting TRDE set in UARTSTAT.
The lpuart driver has auto suspend delay set to 3000ms, but during
uart_add_one_port, a child device serial ctrl will added and probed with
its pm runtime enabled(see serial_ctrl.c).
The runtime suspend call path is:
device_add
|-> bus_probe_device
|->device_initial_probe
|->__device_attach
|-> pm_runtime_get_sync(dev->parent);
|-> pm_request_idle(dev);
|-> pm_runtime_put(dev->parent);
So in the end, before normal console ready, the lpuart get runtime
suspended. And earlycon putchar will hang.
To address the issue, mark last busy just after pm_runtime_enable,
three seconds is long enough to switch from bootconsole to normal
console.
Fixes: 43543e6f539b ("tty: serial: fsl_lpuart: Add runtime pm support")
Cc: stable <stable@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20240808140325.580105-1-peng.fan@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
