| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As we are now enabling full end-to-end flow control to the Thunderbolt
networking driver, in order for it to work properly on second generation
Thunderbolt hardware (Falcon Ridge), we need to add back the workaround
that was removed with commit 53f13319d131 ("thunderbolt: Get rid of E2E
workaround"). However, this time we only apply it for Falcon Ridge
controllers as a form of an additional quirk. For non-Falcon Ridge this
does nothing.
While there fix a typo 'reqister' -> 'register' in the comment.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following what we do for routers already, extend this to XDomain
connections as well. This will show in sysfs whether the link is in USB4
or Thunderbolt mode.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of Thunderbolt and USB changes for 6.0-rc1.
Lots of little things here, nothing major, just constant development
on some new hardware support and cleanups of older drivers. Highlights
are:
- lots of typec changes and improvements for new hardware
- new gadget controller driver
- thunderbolt support for new hardware
- the normal set of new usb-serial device ids and cleanups
- loads of dwc3 controller fixes and improvements
- mtu3 driver updates
- testusb fixes for longtime issues (not many people use this tool it
seems.)
- minor driver fixes and improvements over the USB tree
- chromeos platform driver changes were added and then reverted as
they depened on some typec changes, but the cross-tree merges
caused problems so they will come back later through the platform
tree.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (193 commits)
usb: misc: onboard_usb_hub: Remove duplicated power_on delay
usb: misc: onboard_usb_hub: Add TI USB8041 hub support
usb: misc: onboard_usb_hub: Add reset-gpio support
USB: usbsevseg: convert sysfs snprintf to sysfs_emit
dt-bindings: usb: Add binding for TI USB8041 hub controller
ARM: multi_v7_defconfig: enable USB onboard HUB driver
ARM: dts: stm32: add support for USB2514B onboard hub on stm32mp15xx-dkx
usb: misc: onboard-hub: add support for Microchip USB2514B USB 2.0 hub
dt-bindings: usb: generic-ehci: allow usb-hcd schema properties
usb: typec: ucsi: stm32g0: add bootloader support
usb: typec: ucsi: stm32g0: add support for stm32g0 controller
dt-bindings: usb: typec: add bindings for stm32g0 controller
usb: typec: ucsi: Acknowledge the GET_ERROR_STATUS command completion
usb: cdns3: change place of 'priv_ep' assignment in cdns3_gadget_ep_dequeue(), cdns3_gadget_ep_enable()
usb/chipidea: fix repeated words in comments
usb: renesas-xhci: Do not print any log while fw verif success
usb: typec: retimer: Add missing id check in match callback
USB: xhci: Fix comment typo
usb/typec/tcpm: fix repeated words in comments
usb/musb: fix repeated words in comments
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit updates from Shuah Khan:
"This consists of several fixes and an important feature to discourage
running KUnit tests on production systems. Running tests on a
production system could leave the system in a bad state.
Summary:
- Add a new taint type, TAINT_TEST to signal that a test has been
run.
This should discourage people from running these tests on
production systems, and to make it easier to tell if tests have
been run accidentally (by loading the wrong configuration, etc)
- Several documentation and tool enhancements and fixes"
* tag 'linux-kselftest-kunit-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
Documentation: KUnit: Fix example with compilation error
Documentation: kunit: Add CLI args for kunit_tool
kcsan: test: Add a .kunitconfig to run KCSAN tests
kunit: executor: Fix a memory leak on failure in kunit_filter_tests
clk: explicitly disable CONFIG_UML_PCI_OVER_VIRTIO in .kunitconfig
mmc: sdhci-of-aspeed: test: Use kunit_test_suite() macro
nitro_enclaves: test: Use kunit_test_suite() macro
thunderbolt: test: Use kunit_test_suite() macro
kunit: flatten kunit_suite*** to kunit_suite** in .kunit_test_suites
kunit: unify module and builtin suite definitions
selftest: Taint kernel when test module loaded
module: panic: Taint the kernel when selftest modules load
Documentation: kunit: fix example run_kunit func to allow spaces in args
Documentation: kunit: Cleanup run_wrapper, fix x-ref
kunit: test.h: fix a kernel-doc markup
kunit: tool: Enable virtio/PCI by default on UML
kunit: tool: make --kunitconfig repeatable, blindly concat
kunit: add coverage_uml.config to enable GCOV on UML
kunit: tool: refactor internal kconfig handling, allow overriding
kunit: tool: introduce --qemu_args
...
|
|
The new implementation of kunit_test_suite() for modules no longer
conflicts with module_init, so can now be used by the thunderbolt tests.
Also update the Kconfig entry to enable the test when KUNIT_ALL_TESTS is
enabled.
This means that kunit_tool can now successfully run and parse the test
results with, for example:
./tools/testing/kunit/kunit.py run --arch=x86_64 \
--kconfig_add CONFIG_PCI=y --kconfig_add CONFIG_USB4=y \
'thunderbolt'
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Daniel Latypov <dlatypov@google.com>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Use acpi_find_child_by_adr() to find the child matching a given bus
address instead of tb_acpi_find_port() that walks the list of children
of an ACPI device directly for this purpose and drop the latter.
Apart from simplifying the code, this will help to eliminate the
children list head from struct acpi_device as it is redundant and it
is used in questionable ways in some places (in particular, locking is
needed for walking the list pointed to it safely, but it is often
missing).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
|
|
Delete the redundant word 'the'.
Signed-off-by: Xiang Wangx <wangxiang@cdjrlc.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Intel Raptor Lake has the same integrated Thunderbolt/USB4 controller as
Intel Alder Lake. By default it is still using firmware based connection
manager so we can use most of the Alder Lake flows.
Signed-off-by: George D Sworo <george.d.sworo@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Remove some warnings found by running scripts/kernel-doc,
which is caused by using 'make W=1'.
drivers/thunderbolt/ctl.c:701: warning: expecting prototype for tb_cfg_start().
Prototype was for tb_ctl_start() instead
drivers/thunderbolt/ctl.c:722: warning: expecting prototype for tb_ctrl_stop().
Prototype was for tb_ctl_stop() instead
drivers/thunderbolt/ctl.c:930: warning: expecting prototype for tb_cfg_write().
Prototype was for tb_cfg_write_raw() instead
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Here we configure TMU mode to HiFi uni-directional once DP tunnel
is created. This is due to accuracy requirement for DP tunneling
as appears in CM guide 1.0, section 7.3.2.
Due to Intel hardware limitation, once we changed the TMU mode to HiFi
uni-directional (when DP tunnel exists), we don't change TMU mode back to
normal uni-directional, even if DP tunnel is torn down later.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In this patch we add support for a second low power state of the link: CL1.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle.
We enable it, if both sides of the link support it,
and only for the first hop router (i.e. the first device that connected
to the host router). This is needed for better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In case of uni-directional time sync, TMU handshake is
initiated by upstream router. In case of bi-directional
time sync, TMU handshake is initiated by downstream router.
In order to handle correctly the case of uni-directional mode,
we avoid changing the upstream router's rate to off,
because it might have another downstream router plugged that is set to
uni-directional mode (and we don't want to change its mode).
Instead, we always change downstream router's rate.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Fix few typos in CLx enabling.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Disable CLx before system suspended only if previously was enabled.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We can't enable CLx if it is not supported either by the host or device,
or by the USB4/TBT link (e.g. when an optical cable is used).
We silently ignore CLx enabling in this case.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Intel VT-d driver updates:
- Domain force snooping improvement.
- Cleanups, no intentional functional changes.
- ARM SMMU driver updates:
- Add new Qualcomm device-tree compatible strings
- Add new Nvidia device-tree compatible string for Tegra234
- Fix UAF in SMMUv3 shared virtual addressing code
- Force identity-mapped domains for users of ye olde SMMU legacy
binding
- Minor cleanups
- Fix a BUG_ON in the vfio_iommu_group_notifier:
- Groundwork for upcoming iommufd framework
- Introduction of DMA ownership so that an entire IOMMU group is
either controlled by the kernel or by user-space
- MT8195 and MT8186 support in the Mediatek IOMMU driver
- Make forcing of cache-coherent DMA more coherent between IOMMU
drivers
- Fixes for thunderbolt device DMA protection
- Various smaller fixes and cleanups
* tag 'iommu-updates-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (88 commits)
iommu/amd: Increase timeout waiting for GA log enablement
iommu/s390: Tolerate repeat attach_dev calls
iommu/vt-d: Remove hard coding PGSNP bit in PASID entries
iommu/vt-d: Remove domain_update_iommu_snooping()
iommu/vt-d: Check domain force_snooping against attached devices
iommu/vt-d: Block force-snoop domain attaching if no SC support
iommu/vt-d: Size Page Request Queue to avoid overflow condition
iommu/vt-d: Fold dmar_insert_one_dev_info() into its caller
iommu/vt-d: Change return type of dmar_insert_one_dev_info()
iommu/vt-d: Remove unneeded validity check on dev
iommu/dma: Explicitly sort PCI DMA windows
iommu/dma: Fix iova map result check bug
iommu/mediatek: Fix NULL pointer dereference when printing dev_name
iommu: iommu_group_claim_dma_owner() must always assign a domain
iommu/arm-smmu: Force identity domains for legacy binding
iommu/arm-smmu: Support Tegra234 SMMU
dt-bindings: arm-smmu: Add compatible for Tegra234 SOC
dt-bindings: arm-smmu: Document nvidia,memory-controller property
iommu/arm-smmu-qcom: Add SC8280XP support
dt-bindings: arm-smmu: Add compatible for Qualcomm SC8280XP
...
|
|
Add a KUnit test to check that buffer allocation works also for devices
with no DP adapters.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
For the case of a device without DisplayPort adapters we calculate
incorrectly the amount of buffers. Fix the calculation for this case.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The USB4 Inter-Domain Service specification defines a protocol that can
be used to establish lane bonding between two USB4 domains (hosts). So
far we have not implemented it because the host controller DMA was not
fast enough to be able to go over 20 Gbits/s even if lanes were bonded.
However, starting from Intel Alder Lake CPUs the DMA can go over
20 Gbits/s so now it makes more sense to add this support to the driver.
Because both ends need to negotiate the bonding we add a simple state
machine that tracks the connection state and does the necessary steps
described by the USB4 Inter-Domain Service specification. We only
establish lane bonding when both sides of the link support it. Otherwise
we default to use the single lane. Also this is only done when software
connection manager is used. On systems with firmware based connection
manager, it handles the high-speed tunneling so bonding lanes is
specific to the implementation (Intel firmware based connection manager
does not support lane bonding).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Sometimes when polling for the port after target link width is changed
we get back port locked notification (because the link actually was
reset and then re-trained). Instead of bailing out we can ignore these
when polling for the width change as this is expected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
When bonding lanes over XDomain the host that has "higher" UUID triggers
link re-train for bonding, and the host that has "lower" UUID just waits
for this to happen. To support this split setting the link width and
triggering the actual bonding a separate functions that can be called as
needed.
While there remove duplicated empty line in the kernel-doc comment of
tb_port_lane_bonding_disable().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This should be before tb_wait_for_port() following how the functions in
switch.c are organized.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This is useful when debugging possible issues.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Creating a symlink pointing to the correct USB Type-C
connector for the on-board USB4 ports when they are created.
The link will be created only if the firmware is able to
describe the connection between the port and its connector.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Won Chung <wonchung@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Between me trying to get rid of iommu_present() and Mario wanting to
support the AMD equivalent of DMAR_PLATFORM_OPT_IN, scrutiny has shown
that the iommu_dma_protection attribute is being far too optimistic.
Even if an IOMMU might be present for some PCI segment in the system,
that doesn't necessarily mean it provides translation for the device(s)
we care about. Furthermore, all that DMAR_PLATFORM_OPT_IN really does
is tell us that memory was protected before the kernel was loaded, and
prevent the user from disabling the intel-iommu driver entirely. While
that lets us assume kernel integrity, what matters for actual runtime
DMA protection is whether we trust individual devices, based on the
"external facing" property that we expect firmware to describe for
Thunderbolt ports.
It's proven challenging to determine the appropriate ports accurately
given the variety of possible topologies, so while still not getting a
perfect answer, by putting enough faith in firmware we can at least get
a good bit closer. If we can see that any device near a Thunderbolt NHI
has all the requisites for Kernel DMA Protection, chances are that it
*is* a relevant port, but moreover that implies that firmware is playing
the game overall, so we'll use that to assume that all Thunderbolt ports
should be correctly marked and thus will end up fully protected.
CC: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/b153f208bc9eafab5105bad0358b77366509d2d4.1650878781.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Brad reported that on Apple hardware with Light Ridge or Falcon Ridge
controller, plugging in a chain of Thunderbolt displays (Light Ridge
based controllers) causes all kinds of tearing and flickering. The
reason for this is that on Thunderbolt 1 hardware there is no lane
bonding so we have two independent 10 Gb/s lanes, and currently Linux
tunnels both displays through the lane 1. This makes the displays to
share the 10 Gb/s bandwidth which may not be enough for higher
resolutions.
For this reason make the second tunnel go through the lane 0 instead.
This seems to match what the macOS connection manager is also doing.
Reported-by: Brad Campbell <lists2009@fnarfbargle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
|
|
This is useful when debugging possible issues during tunnel discovery.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
|
|
This makes it consistent with the other logging functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
|
|
Should be 'in' instead of 'bin'. Fix it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
|
|
Replace the NULL checks with the more specific and idiomatic NULL macros.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Daniel Latypov <dlatypov@google.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
To move the list iterator variable into the list_for_each_entry_*()
macro in the future it should be avoided to use the list iterator
variable after the loop body.
To *never* use the list iterator variable after the loop it was
concluded to use a separate iterator variable instead of a
found boolean [1].
This removes the need to use a found variable and simply checking if
the variable was set, can determine if the break/goto was hit.
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
|
|
The structure `tb_eeprom_ctl` is used to show the bits accessed when
reading/writing EEPROM.
As this structure is specified in the USB4 spec as `VSC_CS_4` update
the names and use of members to match the specification. This should not
change anything functionally.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The USB4 1.0 specification outlines the `cap_plug_events` structure as
`VSC_CS_1`. This shows that 4 bits of `VSC_CS_1` are TBT3 compatible in
USB4, but TBT3 controllers also support disabling XHCI.
Update the names and comments to more closely match the specification.
This should not change anything functionally.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The USB4 specification doesn't make any requirements that reading
a device router's DROM is needed for the operation of the device.
Other connection manager solutions don't necessarily read it or gate
the usability of the device on whether it was read.
So make failures when reading the DROM show warnings but not
fail the initialization of the router.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Routers might not have a UID set if the DROM read failed during
initialization previously.
Normally upon resume the UID is re-read to confirm it's the same
device connected.
* If the DROM read failed during init but then succeeded during
resume it could either be a new device or faulty device
* If the DROM read failed during init and also failed during resume
it might be a different device plugged in all together.
Detect this situation and prevent re-using the same configuration in
these cirucmstances.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Currently DROM reads are only retried in the case that parsing failed.
However if the size or CRC fails, then there should also be a retry.
This helps with reading the DROM on TBT3 devices connected to AMD
Yellow Carp which will sometimes fail on the first attempt.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since nvmem_unregister() checks for NULL, no need to repeat in
the caller. Drop duplicate NULL checks.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220220151527.17216-14-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace acpi_bus_get_device() that is going to be dropped with
acpi_fetch_acpi_dev().
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Both Alpine Ridge and Titan Ridge require special flows in order to
activate the internal xHCI controller when there is USB device connected
to the downstream type-C port. This implements the missing flows for
both.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
tb_switch_is_alpine_ridge() is missing device ID for Intel Alpine Ridge
dual port version so add this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Intel Titan Ridge does not disable AUX timers when it gets SET_CONFIG
with SET_LTTPR_MODE set which makes DP tunneling to fail. For this
reason disable LTTPR on Titan Ridge device side.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
While at it, include directly <linux/dma-mapping.h> instead on relying on
indirect inclusion.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Add a module parameter that allows user to completely disable CLx
functionality in case problems are found.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Low power link states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle. The
simplest one being called CL0s. Follow what we already do for USB4
device routers and enable CL0s for Intel Titan Ridge device router too.
This allows better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Rename the VSC capability: TB_VSE_CAP_IECS to TB_VSE_CAP_CP_LP to follow
the Intel devices namings as appear in the datasheet. This capability
is used for controlling CLx (Low Power states of the link).
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Intel Titan Ridge based routers have slightly different flow for time
disruption than USB4 compliant routers. This makes it work on Titan
Ridge too. Needed to enable link low power states on Titan Ridge.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Currently usb4_switch_wait_for_bit() used only in usb4.c Moving to
switch.c to call it from other files. Also change the prefix to "tb_"
to follow to the naming convention.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In this patch we add enabling of CL0s - a low power state of the link.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle. For now,
we add support only for first low power state: CL0s. We enable it, if
both sides of the link support it, and only for the first hop router.
(i.e. the first device that connected to the host router). This is
needed for better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
