summaryrefslogtreecommitdiff
path: root/drivers/spi
AgeCommit message (Collapse)AuthorFilesLines
2009-07-01spi: bitbang bugfix in message setupDavid Brownell1-10/+14
Bugfix to spi_bitbang infrastructure: make sure to always set transfer parameters on the first pass through the message's per-transfer loop. This can matter with drivers that replace the per-word or per-buffer transfer primitives, on busses with multiple SPI devices. Previously, this could have started messages using the settings left after previous messages. The problem was observed when a high speed chip (m25p80 type flash) was running very slowly because a low speed device (avr8 microcontroller) had previously used the bus. Similar faults could have driven the low speed device too fast, or used an unexpected word size. Acked-by: Steven A. Falco <sfalco@harris.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-07-01spi: add spi_master flag wordDavid Brownell1-0/+2
Add a new spi_master.flags word listing constraints relevant to that controller. Define the first constraint bit: a half duplex restriction. Include that constraint in the OMAP1 MicroWire controller driver. Have the mmc_spi host be the first customer of this flag. Its coding relies heavily on full duplex transfers, so it must fail when the underlying controller driver won't perform them. (The spi_write_then_read routine could use it too: use the temporarily-withdrawn full-duplex speedup unless this flag is set, in which case the existing code applies. Similarly, any spi_master implementing only SPI_3WIRE should set the flag.) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-07-01spi: new spi->mode bitsDavid Brownell1-6/+11
Add two new spi_device.mode bits to accomodate more protocol options, and pass them through to usermode drivers: * SPI_NO_CS ... a second 3-wire variant, where the chipselect line is removed instead of a data line; transfers are still full duplex. This obviously has STRONG protocol implications since the chipselect transitions can't be used to synchronize state transitions with the SPI master. * SPI_READY ... defines open drain signal that's pulled low to pause the clock. This defines a 5-wire variant (normal 4-wire SPI plus READY) and two 4-wire variants (READY plus each of the 3-wire flavors). Such hardware flow control can be a big win. There are ADC converters and flash chips that expose READY signals, but not many host controllers support it today. The spi_bitbang code should be changed to use SPI_NO_CS instead of its current nonportable hack. That's a mode most hardware can easily support (unlike SPI_READY). Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: "Paulraj, Sandeep" <s-paulraj@ti.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-20spi_mpc8xxx: s/83xx/8xxx/gAnton Vorontsov3-202/+202
Since we renamed the file, we might want to rename the file internals too. Though we don't bother with changing platform driver name and platform module alias. The stuff is legacy and hopefully we'll remove it soon. Suggested-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-20spi_mpc83xx: rename spi_83xx.c to spi_8xxx.cAnton Vorontsov2-1/+1
The driver handles MPC83xx, MPC85xx and MPC86xx SPI controllers, so rename the file for clarity. Suggested-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Kumar Gala <galak@gate.crashing.org> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-20spi_mpc83xx: remove dead codeAnton Vorontsov1-17/+0
This patch removes #if 0'ed code, and spi_mpc83xx->busy variable that is used by that dead snippet only. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Kumar Gala <galak@gate.crashing.org> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-20spi_mpc83xx: split mpc83xx_spi_work() into two routinesAnton Vorontsov1-55/+60
mpc83xx_spi_work() is quite large, with up to five indentation levels and is quite difficult to read. So, split the function in two parts: 1. mpc83xx_spi_work() now only traverse queued spi messages; 2. mpc83xx_spi_do_one_msg() only manages single messages. There should be no functional changes. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Kumar Gala <galak@gate.crashing.org> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-20spi_mpc83xx: fix checkpatch issuesAnton Vorontsov1-6/+6
Checkpatch is spitting errors when seeing the rename patch, so fix the errors prior to moving. Following errors and warnings were fixed: WARNING: Use #include <linux/io.h> instead of <asm/io.h> #1027: FILE: drivers/spi/spi_mpc8xxx.c:37: +#include <asm/io.h> ERROR: "foo * bar" should be "foo *bar" #1111: FILE: drivers/spi/spi_mpc8xxx.c:121: +static inline void mpc83xx_spi_write_reg(__be32 __iomem * reg, u32 val) ERROR: "foo * bar" should be "foo *bar" #1116: FILE: drivers/spi/spi_mpc8xxx.c:126: +static inline u32 mpc83xx_spi_read_reg(__be32 __iomem * reg) ERROR: "foo * bar" should be "foo *bar" #1125: FILE: drivers/spi/spi_mpc8xxx.c:135: + type * rx = mpc83xx_spi->rx; \ ERROR: "foo * bar" should be "foo *bar" #1135: FILE: drivers/spi/spi_mpc8xxx.c:145: + const type * tx = mpc83xx_spi->tx; \ WARNING: suspect code indent for conditional statements (16, 25) #1504: FILE: drivers/spi/spi_mpc8xxx.c:514: + while (((event = [...] + cpu_relax(); Following warnings were left over, since fixing them will hurt the readability. We'd better fix them by lowering the indentation level by splitting mpc83xx_spi_work function into two parts. WARNING: line over 80 characters #1371: FILE: drivers/spi/spi_mpc8xxx.c:381: + status = mpc83xx_spi_setup_transfer(spi, t); WARNING: line over 80 characters #1392: FILE: drivers/spi/spi_mpc8xxx.c:402: + mpc83xx_spi_chipselect(spi, BITBANG_CS_INACTIVE); Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Kumar Gala <galak@gate.crashing.org> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-20spi_mpc83xx: add small delay after asserting chip-select lineAnton Vorontsov1-1/+3
This is needed for some underlaying GPIO controllers that may be a bit slow, or if chip-select signal need some time to stabilize. For what it's worth, we already have the similar delay for chip-select de-assertion case. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Kumar Gala <galak@gate.crashing.org> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-20spi_mpc83xx: quieten down the "Requested speed is too low" messageAnton Vorontsov1-5/+6
When a platform is running at high frequencies it's not always possible to scale-down a frequency to a requested value, and using mmc_spi driver this leads to the following printk flood during card polling: ... mmc_spi spi32766.0: Requested speed is too low: 400000 Hz. Will use 520828 Hz instead. mmc_spi spi32766.0: Requested speed is too low: 400000 Hz. Will use 520828 Hz instead. ... Fix this by using WARN_ONCE(), it's better than the flood, and also better than turning dev_err() into dev_dbg(), since we actually want to warn that some things may not work correctly. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Kumar Gala <galak@gate.crashing.org> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-20spi_mpc83xx: handle other Freescale processorsAnton Vorontsov1-8/+6
With this patch we'll able to select spi_mpc83xx driver on the MPC86xx platforms. Let the driver depend on FSL_SOC, so we don't have to worry about Kconfig anymore. Also remove the "experimental" dependency, the driver has been tested to work on a various hardware, and surely not experimental anymore. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Kumar Gala <galak@gate.crashing.org> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19spi: fix spi_write_then_read() commentJiri Pirko1-2/+2
Buffer needs not be dma-safe, not rx data length. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19pxa2xx_spi: fix for SPI_CS_HIGHDaniel Ribeiro1-1/+1
Commit a7bb3909b3293d503211d7f6af8ed62c1644b686 ("spi: pxa2xx_spi: introduce chipselect GPIO to simplify the common cases") introduces chipselect GPIO, and configures the CS polarity using SPI_CS_HIGH spi->mode flag. Add SPI_CS_HIGH to the allowed modes. Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19mpc52xx_psc_spi: convert to cs_control callbackAnton Vorontsov1-13/+9
mpc52xx_psc_spi driver is the last user of the legacy activate_cs and deactivate_cs callbacks, so convert the driver to the cs_control hook and remove the legacy callbacks from fsl_spi_platform_data struct. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19spi: move more spi_setup() functionality into coreDavid Brownell15-115/+54
Move some common spi_setup() error checks into the SPI framework from the spi_master controller drivers: - Add a new "mode_bits" field to spi_master - Use that in spi_setup to validate the spi->mode value being requested. Setting this new field is now mandatory for any controller supporting more than vanilla SPI_MODE_0. - Update all spi_master drivers to: * Initialize that field * Remove current spi_setup() checks using that value. This is a net minor code shrink. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19spi: move common spi_setup() functionality into coreDavid Brownell14-56/+60
Start moving some spi_setup() functionality into the SPI core from the various spi_master controller drivers: - Make that function stop being an inline; - Move two common idioms from drivers into that new function: * Default bits_per_word to 8 if that field isn't set * Issue a standardized dev_dbg() message This is a net minor source code shrink, and supports enhancments found in some follow-up patches. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19spi_bfin5xx: limit reaches -1Roel Kluin1-1/+1
bfin_spi_flush() returns limit, which reaches -1 upon timeout. but in function bfin_spi_pump_transfers() it is compared with 0. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Bryan Wu <cooloney@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-17Merge branch 'akpm'Linus Torvalds1-3/+3
* akpm: (182 commits) fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset fbdev: *bfin*: fix __dev{init,exit} markings fbdev: *bfin*: drop unnecessary calls to memset fbdev: bfin-t350mcqb-fb: drop unused local variables fbdev: blackfin has __raw I/O accessors, so use them in fb.h fbdev: s1d13xxxfb: add accelerated bitblt functions tcx: use standard fields for framebuffer physical address and length fbdev: add support for handoff from firmware to hw framebuffers intelfb: fix a bug when changing video timing fbdev: use framebuffer_release() for freeing fb_info structures radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb? s3c-fb: CPUFREQ frequency scaling support s3c-fb: fix resource releasing on error during probing carminefb: fix possible access beyond end of carmine_modedb[] acornfb: remove fb_mmap function mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF mb862xxfb: restrict compliation of platform driver to PPC Samsung SoC Framebuffer driver: add Alpha Channel support atmel-lcdc: fix pixclock upper bound detection offb: use framebuffer_alloc() to allocate fb_info struct ... Manually fix up conflicts due to kmemcheck in mm/slab.c
2009-06-17spi: takes size of a pointer to determine the size of the pointed-to typeRoel Kluin1-3/+3
Do not take the size of a pointer to determine the size of the pointed-to type. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Brownell <david-b@pacbell.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@gate.crashing.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-16Merge branch 'for-linus' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (27 commits) Blackfin: hook up new rt_tgsigqueueinfo syscall Blackfin: improve CLKIN_HZ config default Blackfin: initial support for ftrace grapher Blackfin: initial support for ftrace Blackfin: enable support for LOCKDEP Blackfin: add preliminary support for STACKTRACE Blackfin: move custom sections into sections.h Blackfin: punt unused/wrong mutex-dec.h Blackfin: add support for irqflags Blackfin: add support for bzip2/lzma compressed kernel images Blackfin: convert Kconfig style to def_bool Blackfin: bf548-ezkit: update smsc911x resources Blackfin: update aedos-ipipe code to upstream 1.10-00 Blackfin: bf537-stamp: update ADP5520 resources Blackfin: bf518f-ezbrd: fix SPI CS for SPI flash Blackfin: define SPI IRQ in board resources Blackfin: do not configure the UART early if on wrong processor Blackfin: fix deadlock in SMP IPI handler Blackfin: fix flag storage for irq funcs Blackfin: push down exception oops checking ...
2009-06-15Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds4-1/+1878
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits) MAINTAINERS: EB110ATX is not ebsa110 MAINTAINERS: update Eric Miao's email address and status fb: add support of LCD display controller on pxa168/910 (base layer) [ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN [ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines [ARM] 5544/1: Trust PrimeCell resource sizes [ARM] pxa/sharpsl_pm: cleanup of gpio-related code. [ARM] pxa/sharpsl_pm: drop set_irq_type calls [ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one [ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific [ARM] sa1100: remove unused collie_pm.c [ARM] pxa: fix the conflicting non-static declarations of global_gpios[] [ARM] 5550/1: Add default configure file for w90p910 platform [ARM] 5549/1: Add clock api for w90p910 platform. [ARM] 5548/1: Add gpio api for w90p910 platform [ARM] 5551/1: Add multi-function pin api for w90p910 platform. [ARM] Make ARM_VIC_NR depend on ARM_VIC [ARM] 5546/1: ARM PL022 SSP/SPI driver v3 ARM: OMAP4: SMP: Update defconfig for OMAP4430 ARM: OMAP4: SMP: Enable SMP support for OMAP4430 ...
2009-06-13Blackfin: rename bfin_addr_dcachable to bfin_addr_dcacheableJie Zhang1-2/+2
The latter naming convention is much more common. Signed-off-by: Jie Zhang <jie.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-11Merge branch for-rmk-devel of git://aeryn.fluff.org.uk/bjdooks/linux into develRussell King1-0/+1
2009-06-11[ARM] 5546/1: ARM PL022 SSP/SPI driver v3Linus Walleij3-0/+1876
This adds a driver for the ARM PL022 PrimeCell SSP/SPI driver found in the U300 platforms as well as in some ARM reference hardware, and in a modified version on the Nomadik board. Reviewed-by: Alessandro Rubini <rubini-list@gnudd.com> Reviewed-by: Russell King <linux@arm.linux.org.uk> Reviewed-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-05-24Merge branch 'ixp4xx' of ↵Russell King1-0/+3
git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6 into devel
2009-05-21microblaze: Kconfig: Enable drivers for MicroblazeMichal Simek1-1/+1
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-05-18[ARM] S3C24XX: GPIO: Move gpio functions out of <mach/hardware.h>Ben Dooks1-0/+1
Move all the gpio functions out of <mach/hardware.h> as this file is for defining the generic IO base addresses for the kernel IO calls. Make a new header <mach/gpio-fns.h> to take this and include it via the chain from <linux/gpio.h> which is what most of these files should be using (and will be changed as soon as possible). Note, this does make minor changes to some drivers but should not mess up any pending merges. CC: Richard Purdie <rpurdie@rpsys.net> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> CC: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-05-13pxa2xx_spi: prevent panic case setup() failsDaniel Ribeiro1-0/+3
setup() may fail before ctldata is set, causing a kernel panic on cleanup(). Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-05-07[ARM] Remove arch-imx from build systemSascha Hauer1-1/+1
arch-imx is superseeded by the MXC architecture support. This patch removes arch-imx from the build system. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-04-22spi: pxa2xx: limit reaches -1Roel Kluin1-3/+3
On line 944 the return value of flush() is considered as a boolean, but limit reaches -1 upon timeout which evaluates to true. On 540, 594, 720 the same occurs for wait_ssp_rx_stall() On 536 the same occurs for wait_dma_channel_stop() Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Eric Miao <eric.miao@marvell.com> Cc: David Brownell <david-b@pacbell.net> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-22pxa2xx_spi: restore DRCMR on resumeDaniel Ribeiro1-0/+7
If DMA is enabled, any spi_sync call after suspend/resume would block forever, because DRCMR is lost on suspend. This patch restores DRCMR to the same values set by probe. Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-15Merge branch 'fix' of ↵Russell King1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6
2009-04-14spi: spi_write_then_read() bugfixesDavid Brownell1-8/+14
The "simplify spi_write_then_read()" patch included two regressions from the 2.6.27 behaviors: - The data it wrote out during the (full duplex) read side of the transfer was not zeroed. - It fails completely on half duplex hardware, such as Microwire and most "3-wire" SPI variants. So, revert that patch. A revised version should be submitted at some point, which can get the speedup on standard hardware (full duplex) without breaking on less-capable half-duplex stuff. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: <stable@kernel.org> [2.6.28.x, 2.6.29.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-13[ARM] pxa: fix typo of cs_deassert() in pxa2xx-spi.cDaniel Ribeiro1-1/+1
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
2009-04-07spi_imx: set spi_master.dma_alignment = 4Mike Rapoport1-0/+2
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Cc: Bryan Wu <bryan.wu@analog.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07pxa2xx_spi: set spi_master.dma_alignment = 8Mike Rapoport1-0/+2
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Cc: Bryan Wu <bryan.wu@analog.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07spi_bfin5xx: remove unused IS_DMA_ALIGNED macroMike Rapoport1-2/+0
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Cc: Bryan Wu <bryan.wu@analog.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07spi: pxa2xx_spi: introduce chipselect GPIO to simplify the common casesEric Miao1-18/+78
Most SPI peripherals use GPIOs as their chip selects, introduce .gpio_cs for this. Signed-off-by: Eric Miao <eric.miao@marvell.com> Cc: David Brownell <david-b@pacbell.net> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07spi: limit reaches -1, tested 0Roel Kluin1-1/+2
With a postfix decrement limit will reach -1 rather than 0, so the warning will not be issued. Also, add a cpu_relax() into the busy-wait loop. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Mariusz Ceier <mceier@gmail.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: Make mmc_spi driver work on BlackfinWolfgang Muees1-142/+108
1. Rewrite of the non-dma data transfer functions to use only ONE mode of TIMOD (TIMOD=0x1). With TIMOD=0, it was not possible to set the TX bit pattern. So the TDBR = 0xFFFF inside the read calls won't work. 2. Clear SPI_RDBR before reading and before duplex transfer. Otherwise the garbage data in RDBR will get read. Since mmc_spi uses a lot of duplex transfers, this is the main cause of mmc_spi failure. 3. Poll RXS for transfer completion. Polling SPIF or TXS cannot guarantee transfer completion. This may interrupt a transfer before it is finished. Also this may leave garbage data in buffer and affect next transfer. [Yi Li <yi.li@analog.com>: add a field "u16 idle_tx_val" in "struct bfin5xx_spi_chip" to specify the value to transmit if no TX value is supplied.] Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Signed-off-by: Yi Li <yi.li@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: Add GPIO controlled SPI Slave Select supportMichael Hennerich1-8/+32
Add support for GPIO controlled SPI Chip Selects. To make use of this feature, set chip_select = 0 and add a proper cs_gpio to your controller_data. struct spi_board_info .chip_select = 0 struct bfin5xx_spi_chip .cs_gpio = GPIO_P### There are various SPI devices that require SPI MODE_0, and need to have the Chip Selects asserted during the entire transfer. Consider using SPI_MODE_3 (SPI_CPHA | SPI_CPOL) if your device allows it. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: fix NULL pointer crashMike Frysinger1-0/+3
Fix NULL pointer crash when cleaning up from invalid platform resources Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: use bfin_spi_ prefix on all functionsMike Frysinger1-111/+112
Do this because when things crash, we get simple names like "setup" and "start_queue" which is pretty difficult to trace back to the real thing: the spi driver Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: fix bug - correct usage of struct spi_transfer.cs_changeYi Li1-9/+8
According to comments in linux/spi/spi.h: * All SPI transfers start with the relevant chipselect active. Normally * it stays selected until after the last transfer in a message. Drivers * can affect the chipselect signal using cs_change. * * (i) If the transfer isn't the last one in the message, this flag is * used to make the chipselect briefly go inactive in the middle of the * message. Toggling chipselect in this way may be needed to terminate * a chip command, letting a single spi_message perform all of group of * chip transactions together. * * (ii) When the transfer is the last one in the message, the chip may * stay selected until the next transfer. On multi-device SPI busses * with nothing blocking messages going to other devices, this is just * a performance hint; starting a message to another device deselects * this one. But in other cases, this can be used to ensure correctness. * Some devices need protocol transactions to be built from a series of * spi_message submissions, where the content of one message is determined * by the results of previous messages and where the whole transaction * ends when the chipselect goes intactive. Signed-off-by: Yi Li <yi.li@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: fix bug - spi controller driver does not ↵Yi Li1-3/+2
assert/deassert CS correctly This bug can be observed when two SPI devices are sharing the spi bus: One device is set as SPI CS 7, another one is using SPI CS 4. In spi_bfin5xx.c: cs_active(), cs_deactive() are used to control SPI_FLG register. From the debug bellow: cs_active: flag: 0x7f91, chip->flag: 0x7f80, cs: 7 cs_active: flag: 0xef91, chip->flag: 0xef10, cs: 4 When device A (cs_7) activate CS 7, SPI_FLG is set as 0x7f91 (however, SPI_FLG should be set as 0x7f80, or 0x6f91 if in broadcast mode). Due to some HW bug (very possibly), if SPI_FLG is set as 0x7f91, SPISSEL7 is asserted, however SPISSEL4 will be asserted too (I can see this using the scope). This is unreasonable according to HRM. Signed-off-by: Yi Li <yi.li@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: tweak magic spi dma sequence to get it working on BF54xMike Frysinger1-1/+2
Without this change, SPI DMA is not reliably under stress tests. Obiviously it's a hardware issue which is not addressed by any document. Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: add timeout while waiting for SPIF in dma irq handlerMike Frysinger1-1/+11
The "while" endless loop will cause the system hang if hardware error, so we add timeout control to make the system alive. Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: get dma working for SPI flashesMike Frysinger1-10/+16
When using a BF533-STAMP here with a W25X10 SPI flash. It works fine when enable_dma is disabled, but doesn't work at all when turning DMA on. We get just 0xff bytes back when trying to read the device. Change the code around so that it programs the SPI first and then enables DMA, it seems to work a lot better ... Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: SPI slave select code cleanupMike Frysinger1-3/+1
- remove duplicated definition MAX_SPI_SSEL - remove unnecessary array size Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07Blackfin SPI Driver: use the properl BIT_CTL_xxx definesMike Frysinger1-3/+3
use the properl BIT_CTL_... defines rather than the internal driv er CFG_SPI_... defines Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-11-25 15:56:56 +0300