| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit ef222f551e7c4e2008fc442ffc9edcd1a7fd8f63 upstream.
While performing certain power-off sequences, PCI drivers are called to
suspend and resume their underlying devices through PCI PM (power
management) interface. However the hardware does not support PCI PM
suspend/resume operations so system wide suspend/resume leads to bad MFW
(management firmware) state which causes various follow-up errors in driver
when communicating with the device/firmware.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding system
to go into suspended/standby mode.
Fixes: 61d8658b4a43 ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.")
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230807093725.46829-1-njavali@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1516ee035df32115197cd93ae3619dba7b020986 upstream.
While performing certain power-off sequences, PCI drivers are called to
suspend and resume their underlying devices through PCI PM (power
management) interface. However the hardware does not support PCI PM
suspend/resume operations so system wide suspend/resume leads to bad MFW
(management firmware) state which causes various follow-up errors in driver
when communicating with the device/firmware.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding system
to go into suspended/standby mode.
Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230807093725.46829-2-njavali@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a43b07a87835660f91d88a4db11abfea8c523b7 upstream.
fnic_clean_pending_aborts() was returning a non-zero value irrespective of
failure or success. This caused the caller of this function to assume that
the device reset had failed, even though it would succeed in most cases. As
a consequence, a successful device reset would escalate to host reset.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Tested-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20230727193919.2519-1-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 04b5b5cb0136ce970333a9c6cec7e46adba1ea3a upstream.
If device_add() returns error, the name allocated by dev_set_name() needs
be freed. As the comment of device_add() says, put_device() should be used
to decrease the reference count in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanp().
Fixes: ee959b00c335 ("SCSI: convert struct class_device to struct device")
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Link: https://lore.kernel.org/r/20230803020230.226903-1-wangzhu9@huawei.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41320b18a0e0dfb236dba4edb9be12dba1878156 upstream.
If device_add() returns error, the name allocated by dev_set_name() needs
be freed. As the comment of device_add() says, put_device() should be used
to give up the reference in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanp().
Fixes: c8806b6c9e82 ("snic: driver for Cisco SCSI HBA")
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Acked-by: Narsimhulu Musini <nmusini@cisco.com>
Link: https://lore.kernel.org/r/20230801111421.63651-1-wangzhu9@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8366d1f1249a0d0bba41d0bd1298d63e5d34c7f7 upstream.
Add a check for the command slot value to avoid dereferencing a NULL
pointer.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Co-developed-by: Vladimir Telezhnikov <vtelezhnikov@astralinux.ru>
Signed-off-by: Vladimir Telezhnikov <vtelezhnikov@astralinux.ru>
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Link: https://lore.kernel.org/r/20230728123521.18293-1-adiupina@astralinux.ru
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 175544ad48cbf56affeef2a679c6a4d4fb1e2881 upstream.
Hyper-V provides the ability to connect Fibre Channel LUNs to the host
system and present them in a guest VM as a SCSI device. I/O to the vFC
device is handled by the storvsc driver. The storvsc driver includes a
partial integration with the FC transport implemented in the generic
portion of the Linux SCSI subsystem so that FC attributes can be displayed
in /sys. However, the partial integration means that some aspects of vFC
don't work properly. Unfortunately, a full and correct integration isn't
practical because of limitations in what Hyper-V provides to the guest.
In particular, in the context of Hyper-V storvsc, the FC transport timeout
function fc_eh_timed_out() causes a kernel panic because it can't find the
rport and dereferences a NULL pointer. The original patch that added the
call from storvsc_eh_timed_out() to fc_eh_timed_out() is faulty in this
regard.
In many cases a timeout is due to a transient condition, so the situation
can be improved by just continuing to wait like with other I/O requests
issued by storvsc, and avoiding the guaranteed panic. For a permanent
failure, continuing to wait may result in a hung thread instead of a panic,
which again may be better.
So fix the panic by removing the storvsc call to fc_eh_timed_out(). This
allows storvsc to keep waiting for a response. The change has been tested
by users who experienced a panic in fc_eh_timed_out() due to transient
timeouts, and it solves their problem.
In the future we may want to deprecate the vFC functionality in storvsc
since it can't be fully fixed. But it has current users for whom it is
working well enough, so it should probably stay for a while longer.
Fixes: 3930d7309807 ("scsi: storvsc: use default I/O timeout handler for FC devices")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1690606764-79669-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9426d3cef5000824e5f24f80ed5f42fb935f2488 upstream.
(lightly modified commit message mostly by Linus Torvalds)
The parsing code for /proc/scsi/scsi is disgusting and broken. We should
have just used 'sscanf()' or something simple like that, but the logic may
actually predate our kernel sscanf library routine for all I know. It
certainly predates both git and BK histories.
And we can't change it to be something sane like that now, because the
string matching at the start is done case-insensitively, and the separator
parsing between numbers isn't done at all, so *any* separator will work,
including a possible terminating NUL character.
This interface is root-only, and entirely for legacy use, so there is
absolutely no point in trying to tighten up the parsing. Because any
separator has traditionally worked, it's entirely possible that people have
used random characters rather than the suggested space.
So don't bother to try to pretty it up, and let's just make a minimal patch
that can be back-ported and we can forget about this whole sorry thing for
another two decades.
Just make it at least not read past the end of the supplied data.
Link: https://lore.kernel.org/linux-scsi/b570f5fe-cb7c-863a-6ed9-f6774c219b88@cybernetics.com/
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin K Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <jejb@linux.ibm.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: stable@kernel.org
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Martin K Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 010c1e1c5741365dbbf44a5a5bb9f30192875c4c upstream.
The Hyper-V host is queried to get the max transfer size that it supports,
and this value is used to set max_sectors for the synthetic SCSI
controller. However, this max transfer size may be too large for virtual
Fibre Channel devices, which are limited to 512 Kbytes. If a larger
transfer size is used with a vFC device, Hyper-V always returns an error,
and storvsc logs a message like this where the SRB status and SCSI status
are both zero:
hv_storvsc <GUID>: tag#197 cmd 0x8a status: scsi 0x0 srb 0x0 hv 0xc0000001
Add logic to limit the max transfer size to 512 Kbytes for vFC devices.
Fixes: 1d3e0980782f ("scsi: storvsc: Correct reporting of Hyper-V I/O size limits")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1689887102-32806-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 339020091e246e708c1381acf74c5f8e3fe4d2b5 upstream.
This loop will exit successfully when "found" is false or in the failure
case it times out with "wait_iter" set to -1. The test for timeouts is
impossible as is.
Fixes: b843adde8d49 ("scsi: qla2xxx: Fix mem access after free")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/cea5a62f-b873-4347-8f8e-c67527ced8d2@kili.mountain
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 20fce500b232b970e40312a9c97e7f3b6d7a709c upstream.
System crash when qla2x00_start_sp(sp) returns error code EGAIN and wake_up
gets called for uninitialized wait queue sp->nvme_ls_waitq.
qla2xxx [0000:37:00.1]-2121:5: Returning existing qpair of ffff8ae2c0513400 for idx=0
qla2xxx [0000:37:00.1]-700e:5: qla2x00_start_sp failed = 11
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
Hardware name: HPE ProLiant DL360 Gen10/ProLiant DL360 Gen10, BIOS U32 09/03/2021
Workqueue: nvme-wq nvme_fc_connect_ctrl_work [nvme_fc]
RIP: 0010:__wake_up_common+0x4c/0x190
RSP: 0018:ffff95f3e0cb7cd0 EFLAGS: 00010086
RAX: 0000000000000000 RBX: ffff8b08d3b26328 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000003 RDI: ffff8b08d3b26320
RBP: 0000000000000001 R08: 0000000000000000 R09: ffffffffffffffe8
R10: 0000000000000000 R11: ffff95f3e0cb7a60 R12: ffff95f3e0cb7d20
R13: 0000000000000003 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8b2fdf6c0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000002f1e410002 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
__wake_up_common_lock+0x7c/0xc0
qla_nvme_ls_req+0x355/0x4c0 [qla2xxx]
? __nvme_fc_send_ls_req+0x260/0x380 [nvme_fc]
? nvme_fc_send_ls_req.constprop.42+0x1a/0x45 [nvme_fc]
? nvme_fc_connect_ctrl_work.cold.63+0x1e3/0xa7d [nvme_fc]
Remove unused nvme_ls_waitq wait queue. nvme_ls_waitq logic was removed
previously in the commits tagged Fixed: below.
Fixes: 219d27d7147e ("scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands")
Fixes: 5621b0dd7453 ("scsi: qla2xxx: Simpify unregistration of FC-NVMe local/remote ports")
Cc: stable@vger.kernel.org
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230615074633.12721-1-njavali@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 00eca15319d9ce8c31cdf22f32a3467775423df4 upstream.
Klocwork tool reported pointer 'rport' returned from call to function
fc_bsg_to_rport() may be NULL and will be dereferenced.
Add a fix to validate rport before dereferencing.
Cc: stable@vger.kernel.org
Signed-off-by: Shreyas Deodhar <sdeodhar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230607113843.37185-7-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b1b9d3825df4c757d653d0b1df66f084835db9c3 upstream.
Klocwork reported array 'port_dstate_str' of size 10 may use index value(s)
10..15.
Add a fix to correct the index of array.
Cc: stable@vger.kernel.org
Signed-off-by: Bikash Hazarika <bhazarika@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230607113843.37185-8-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit af73f23a27206ffb3c477cac75b5fcf03410556e upstream.
Klocwork reported warning of rport maybe NULL and will be dereferenced.
rport returned by call to fc_bsg_to_rport() could be NULL and dereferenced.
Check valid rport returned by fc_bsg_to_rport().
Cc: stable@vger.kernel.org
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230607113843.37185-5-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 464ea494a40c6e3e0e8f91dd325408aaf21515ba upstream.
Klocwork tool reported 'cur_dsd' may be dereferenced. Add fix to validate
pointer before dereferencing the pointer.
Cc: stable@vger.kernel.org
Signed-off-by: Bikash Hazarika <bhazarika@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230607113843.37185-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b68710a8094fdffe8dd4f7a82c82649f479bb453 upstream.
Klocwork warning: Buffer Overflow - Array Index Out of Bounds
Driver uses fc_els_flogi to calculate size of buffer. The actual buffer is
nested inside of fc_els_flogi which is smaller.
Replace structure name to allow proper size calculation.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230607113843.37185-6-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6b504d06976fe4a61cc05dedc68b84fadb397f77 upstream.
Klocwork reported warning of NULL pointer may be dereferenced. The routine
exits when sa_ctl is NULL and fcport is allocated after the exit call thus
causing NULL fcport pointer to dereference at the time of exit.
To avoid fcport pointer dereference, exit the routine when sa_ctl is NULL.
Cc: stable@vger.kernel.org
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230607113843.37185-4-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d721b591b95cf3f290f8a7cbe90aa2ee0368388d upstream.
Klocwork reports array 'vha->host_str' of size 16 may use index value(s)
16..19. Use snprintf() instead of sprintf().
Cc: stable@vger.kernel.org
Co-developed-by: Bikash Hazarika <bhazarika@marvell.com>
Signed-off-by: Bikash Hazarika <bhazarika@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230607113843.37185-2-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b843adde8d490934d042fbe9e3e46697cb3a64d2 upstream.
System crash, where driver is accessing scsi layer's
memory (scsi_cmnd->device->host) to search for a well known internal
pointer (vha). The scsi_cmnd was released back to upper layer which
could be freed, but the driver is still accessing it.
7 [ffffa8e8d2c3f8d0] page_fault at ffffffff86c010fe
[exception RIP: __qla2x00_eh_wait_for_pending_commands+240]
RIP: ffffffffc0642350 RSP: ffffa8e8d2c3f988 RFLAGS: 00010286
RAX: 0000000000000165 RBX: 0000000000000002 RCX: 00000000000036d8
RDX: 0000000000000000 RSI: ffff9c5c56535188 RDI: 0000000000000286
RBP: ffff9c5bf7aa4a58 R8: ffff9c589aecdb70 R9: 00000000000003d1
R10: 0000000000000001 R11: 0000000000380000 R12: ffff9c5c5392bc78
R13: ffff9c57044ff5c0 R14: ffff9c56b5a3aa00 R15: 00000000000006db
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
8 [ffffa8e8d2c3f9c8] qla2x00_eh_wait_for_pending_commands at ffffffffc0646dd5 [qla2xxx]
9 [ffffa8e8d2c3fa00] __qla2x00_async_tm_cmd at ffffffffc0658094 [qla2xxx]
Remove access of freed memory. Currently the driver was checking to see if
scsi_done was called by seeing if the sp->type has changed. Instead,
check to see if the command has left the oustanding_cmds[] array as
sign of scsi_done was called.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230428075339.32551-6-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fc0cba0c7be8261a1625098bd1d695077ec621c9 upstream.
System crash due to use after free.
Current code allows terminate_rport_io to exit before making
sure all IOs has returned. For FCP-2 device, IO's can hang
on in HW because driver has not tear down the session in FW at
first sign of cable pull. When dev_loss_tmo timer pops,
terminate_rport_io is called and upper layer is about to
free various resources. Terminate_rport_io trigger qla to do
the final cleanup, but the cleanup might not be fast enough where it
leave qla still holding on to the same resource.
Wait for IO's to return to upper layer before resources are freed.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230428075339.32551-7-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9ae615c5bfd37bd091772969b1153de5335ea986 upstream.
Task management command hangs where a side
band chip reset failed to nudge the TMF
from it's current send path.
Add additional error check to block TMF
from entering during chip reset and along
the TMF path to cause it to bail out, skip
over abort of marker.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230428075339.32551-5-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6a87679626b51b53fbb6be417ad8eb083030b617 upstream.
Task management command failed with status 2Ch which is
a result of too many task management commands sent
to the same target. Hence limit task management commands
to 8 per target.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304271952.NKNmoFzv-lkp@intel.com/
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230428075339.32551-4-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9803fb5d27597ea98f2e05b0b6cfc48ae808458e upstream.
Task management cmd failed with status 30h which means
FW is not able to finish processing one task management
before another task management for the same lun.
Hence add wait for completion of marker to space it out.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304271802.uCZfwQC1-lkp@intel.com/
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230428075339.32551-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com <mailto:himanshu.madhani@oracle.com>>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d90171dd0da50212f5950cc708240831e82f2f91 upstream.
Add queue flush for task management command, before
placing it on the wire.
Do IO flush for all Request Q's.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304271702.GpIL391S-lkp@intel.com/
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230428075339.32551-2-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com <mailto:himanshu.madhani@oracle.com>>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
lpfc_nlp_not_used()
commit 97f975823f8196d970bd795087b514271214677a upstream.
Smatch detected a double free path because lpfc_nlp_not_used() releases an
ndlp object before reaching lpfc_nlp_put() at the end of
lpfc_cmpl_els_logo_acc().
Remove the outdated lpfc_nlp_not_used() routine. In
lpfc_mbx_cmpl_ns_reg_login(), replace the call with lpfc_nlp_put(). In
lpfc_cmpl_els_logo_acc(), replace the call with lpfc_unreg_rpi() and keep
the lpfc_nlp_put() at the end of the routine. If ndlp's rpi was
registered, then lpfc_unreg_rpi()'s completion routine performs the final
ndlp clean up after lpfc_nlp_put() is called from lpfc_cmpl_els_logo_acc().
Otherwise if ndlp has no rpi registered, the lpfc_nlp_put() at the end of
lpfc_cmpl_els_logo_acc() is the final ndlp clean up.
Fixes: 4430f7fd09ec ("scsi: lpfc: Rework locations of ndlp reference taking")
Cc: <stable@vger.kernel.org> # v5.11+
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/all/Y3OefhyyJNKH%2Fiaf@kili/
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20230417191558.83100-3-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f762326b2baa86ae647e2ba6832bc87e238f68ad upstream.
Copy the sense data to internal driver buffer when the firmware completes
any SCSI I/O command sent through admin queue with sense data for further
use.
Fixes: 506bc1a0d6ba ("scsi: mpi3mr: Add support for MPT commands")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20230531184025.3803-1-sumit.saxena@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e579b007eff3ff8d29d59d16214cd85fb9e573f7 ]
This should be negative -EAGAIN instead of positive. The callers treat
non-zero error codes the same so it doesn't really impact runtime beyond
some trivial differences to debug output.
Fixes: 80676d054e5a ("scsi: qla2xxx: Fix session cleanup hang")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/49866d28-4cfe-47b0-842b-78f110e61aab@moroto.mountain
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9914a3d033d3e1d836a43e93e9738e7dd44a096a ]
When NPIV ports are zoned to devices that support both initiator and target
mode, a remote device's initiated PRLI results in unintended final kref
clean up of the device's ndlp structure. This disrupts NPIV ports'
discovery for target devices that support both initiator and target mode.
Modify the NPIV lpfc_drop_node clause such that we allow the ndlp to live
so long as it was in NLP_STE_PLOGI_ISSUE, NLP_STE_REG_LOGIN_ISSUE, or
NLP_STE_PRLI_ISSUE nlp_state. This allows lpfc's issued PRLI completion
routine to determine if the final kref clean up should execute rather than
a remote device's issued PRLI.
Fixes: db651ec22524 ("scsi: lpfc: Correct used_rpi count when devloss tmo fires with no recovery")
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20230523183206.7728-5-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2e2fe5ac695a00ab03cab4db1f4d6be07168ed9d ]
Smatch complains that:
tw_probe() warn: missing error code 'retval'
This patch adds error checking to tw_probe() to handle initialization
failure. If tw_reset_sequence() function returns a non-zero value, the
function will return -EINVAL to indicate initialization failure.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Yuchen Yang <u202114568@hust.edu.cn>
Link: https://lore.kernel.org/r/20230505141259.7730-1-u202114568@hust.edu.cn
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f025312b089474a54e4859f3453771314d9e3d4f ]
Smatch reported:
drivers/scsi/qedf/qedf_main.c:3056 qedf_alloc_global_queues()
warn: missing unwind goto?
At this point in the function, nothing has been allocated so we can return
directly. In particular the "qedf->global_queues" have not been allocated
so calling qedf_free_global_queues() will lead to a NULL dereference when
we check if (!gl[i]) and "gl" is NULL.
Fixes: 61d8658b4a43 ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.")
Signed-off-by: Jinhong Zhu <jinhongzhu@hust.edu.cn>
Link: https://lore.kernel.org/r/20230502140022.2852-1-jinhongzhu@hust.edu.cn
Reviewed-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a9a3629592ab7442a2e9d40281420b51c453ea9b upstream.
struct MPI2_RAID_SCSI_IO_REQUEST ends with a single SGL, but expects to
copy multiple. Add a flexible array member so the compiler can reason about
the size of the memcpy(). This will avoid the run-time false positive
warning:
memcpy: detected field-spanning write (size 128) of single field "&r1_cmd->io_request->SGL" at drivers/scsi/megaraid/megaraid_sas_fusion.c:3326 (size 16)
This change results in no binary output differences.
Reported-by: Holger Kiehl <Holger.Kiehl@dwd.de>
Link: https://lore.kernel.org/all/88de8faa-56c4-693d-2d3-67152ee72057@diagnostix.dwd.de/
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: megaraidlinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Link: https://lore.kernel.org/r/20230106053153.never.999-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Holger Kiehl <Holger.Kiehl@dwd.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d074ce231772c66e648a61f6bd2245e7129d1f5 upstream.
gcc 13 may assign another type to enumeration constants than gcc 12. Split
the large enum at the top of source file stex.c such that the type of the
constants used in time expressions is changed back to the same type chosen
by gcc 12. This patch suppresses compiler warnings like this one:
In file included from ./include/linux/bitops.h:7,
from ./include/linux/kernel.h:22,
from drivers/scsi/stex.c:13:
drivers/scsi/stex.c: In function ‘stex_common_handshake’:
./include/linux/typecheck.h:12:25: error: comparison of distinct pointer types lacks a cast [-Werror]
12 | (void)(&__dummy == &__dummy2); \
| ^~
./include/linux/jiffies.h:106:10: note: in expansion of macro ‘typecheck’
106 | typecheck(unsigned long, b) && \
| ^~~~~~~~~
drivers/scsi/stex.c:1035:29: note: in expansion of macro ‘time_after’
1035 | if (time_after(jiffies, before + MU_MAX_DELAY * HZ)) {
| ^~~~~~~~~~
See also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107405.
Cc: stable@vger.kernel.org
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230529195034.3077-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 09e797c8641f6ad435c33ae24c223351197ea29a ]
If scsi_dispatch_cmd() failed, the SCSI command was not sent to the target,
scsi_queue_rq() would return BLK_STS_RESOURCE and the related request would
be requeued. The timeout of this request would not fire, no one would
increase iodone_cnt.
The above flow would result the iodone_cnt smaller than iorequest_cnt. So
decrease the iorequest_cnt if dispatch failed to workaround the issue.
Signed-off-by: Wenchao Hao <haowenchao2@huawei.com>
Reported-by: Ming Lei <ming.lei@redhat.com>
Closes: https://lore.kernel.org/r/ZF+zB+bB7iqe0wGd@ovpn-8-17.pek2.redhat.com
Link: https://lore.kernel.org/r/20230515070156.1790181-3-haowenchao2@huawei.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4e81a6cba517cb33584308a331f14f5e3fec369b ]
In a SCSI request, storvsc pre-allocates space for up to
MAX_PAGE_BUFFER_COUNT physical frame numbers to be passed to Hyper-V. If
the size of the I/O request requires more PFNs, a separate memory area of
exactly the correct size is dynamically allocated.
But when the pre-allocated area is used, current code always passes
MAX_PAGE_BUFFER_COUNT PFNs to Hyper-V, even if fewer are needed. While
this doesn't break anything because the additional PFNs are always zero,
more bytes than necessary are copied into the VMBus channel ring buffer.
This takes CPU cycles and wastes space in the ring buffer. For a typical 4
Kbyte I/O that requires only a single PFN, 248 unnecessary bytes are
copied.
Fix this by setting the payload_sz based on the actual number of PFNs
required, not the size of the pre-allocated space.
Reported-by: John Starks <jostarks@microsoft.com>
Fixes: 8f43710543ef ("scsi: storvsc: Support PAGE_SIZE larger than 4K")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1684171241-16209-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit db651ec22524eb8f9c854fbb4d9acd5d7e5be9e4 ]
A fabric controller can sometimes send an RDP request right before a link
down event. Because of this outstanding RDP request, the driver does not
remove the last reference count on its ndlp causing a potential leak of RPI
resources when devloss tmo fires.
In lpfc_cmpl_els_rsp(), modify the NPIV clause to always allow the
lpfc_drop_node() routine to execute when not registered with SCSI
transport.
This relaxes the contraint that an NPIV ndlp must be in a specific state in
order to call lpfc_drop node. Logic is revised such that the
lpfc_drop_node() routine is always called to ensure the last ndlp decrement
occurs.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20230301231626.9621-7-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c6087b82a9146826564a55c5ca0164cac40348f5 ]
A static code analysis tool flagged the possibility of buffer overflow when
using copy_from_user() for a debugfs entry.
Currently, it is possible that copy_from_user() copies more bytes than what
would fit in the mybuf char array. Add a min() restriction check between
sizeof(mybuf) - 1 and nbytes passed from the userspace buffer to protect
against buffer overflow.
Link: https://lore.kernel.org/r/20230301231626.9621-2-justintee8345@gmail.com
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c5749639f2d0a1f6cbe187d05f70c2e7c544d748 ]
In qedi_probe() we call __qedi_probe() which initializes
&qedi->recovery_work with qedi_recovery_handler() and
&qedi->board_disable_work with qedi_board_disable_work().
When qedi_schedule_recovery_handler() is called, schedule_delayed_work()
will finally start the work.
In qedi_remove(), which is called to remove the driver, the following
sequence may be observed:
Fix this by finishing the work before cleanup in qedi_remove().
CPU0 CPU1
|qedi_recovery_handler
qedi_remove |
__qedi_remove |
iscsi_host_free |
scsi_host_put |
//free shost |
|iscsi_host_for_each_session
|//use qedi->shost
Cancel recovery_work and board_disable_work in __qedi_remove().
Fixes: 4b1068f5d74b ("scsi: qedi: Add MFW error recovery process")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Link: https://lore.kernel.org/r/20230413033422.28003-1-zyytlz.wz@163.com
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a67aad57d9aee41180aff36e54cb72fe4b8d5a5a upstream.
Grab the ATA port lock in sas_ata_device_link_abort() before calling
ata_link_abort() as outlined in this function's locking requirements.
Fixes: 44112922674b ("scsi: libsas: Add sas_ata_device_link_abort()")
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 91a0c0c1413239d0548b5aac4c82f38f6d53a91e ]
When if_type equals zero and pci_resource_start(pdev, PCI_64BIT_BAR4)
returns false, drbl_regs_memmap_p is not remapped. This passes a NULL
pointer to iounmap(), which can trigger a WARN() on certain arches.
When if_type equals six and pci_resource_start(pdev, PCI_64BIT_BAR4)
returns true, drbl_regs_memmap_p may has been remapped and
ctrl_regs_memmap_p is not remapped. This is a resource leak and passes a
NULL pointer to iounmap().
To fix these issues, we need to add null checks before iounmap(), and
change some goto labels.
Fixes: 1351e69fc6db ("scsi: lpfc: Add push-to-adapter support to sli4")
Signed-off-by: Shuchang Li <lishuchang@hust.edu.cn>
Link: https://lore.kernel.org/r/20230404072133.1022-1-lishuchang@hust.edu.cn
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bb544224da77b96b2c11a13872bf91ede1e015be ]
If an NCQ error occurs when the IPTT is valid and slot->abort flag is set
in completion path, sas_task_abort() will be called to abort only one NCQ
command now, and the host would be set to SHOST_RECOVERY state. But this
may not kick-off EH Immediately until other outstanding QCs timeouts. As a
result, the host may remain in the SHOST_RECOVERY state for up to 30
seconds, such as follows:
[7972317.645234] hisi_sas_v3_hw 0000:74:04.0: erroneous completion iptt=3264 task=00000000466116b8 dev id=2 sas_addr=0x5000000000000502 CQ hdr: 0x1883 0x20cc0 0x40000 0x20420000 Error info: 0x0 0x0 0x200000 0x0
[7972341.508264] sas: Enter sas_scsi_recover_host busy: 32 failed: 32
[7972341.984731] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 32 tries: 1
All NCQ commands that are in the queue should be aborted when an NCQ error
occurs in this scenario.
Fixes: 05d91b557af9 ("scsi: hisi_sas: Directly trigger SCSI error handling for completion errors")
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1679283265-115066-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 44112922674b94a7d699dfff6307fc830018df7c ]
Similar to how AHCI handles NCQ errors in ahci_error_intr() ->
ata_port_abort() -> ata_do_link_abort(), add an NCQ error handler for LLDDs
to call to initiate a link abort.
This will mark all outstanding QCs as failed and kick-off EH.
Note:
A "force reset" argument is added for drivers which require the ATA error
handling to always reset the device.
A driver may require this feature for when SATA device per-SCSI cmnd
resources are only released during reset for ATA EH. As such, we need an
option to force reset to be done, regardless of what any EH autopsy
decides.
The SATA device FIS fields are set to indicate a device error from
ata_eh_analyze_tf().
Suggested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Suggested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1665998435-199946-2-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com> # pm80xx
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: bb544224da77 ("scsi: hisi_sas: Handle NCQ error when IPTT is valid")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 75cb113cd43f06aaf4f1bda0069cfd5b98e909eb ]
When cmdid == CMDID_INT_CMDS, the 'cmds' pointer is NULL but is
dereferenced below.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0f2bb84d2a68 ("[SCSI] megaraid: simplify internal command handling")
Signed-off-by: Danila Chernetsov <listdansp@mail.ru>
Link: https://lore.kernel.org/r/20230317175109.18585-1-listdansp@mail.ru
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a3d27dfdcfc27ac3f46de5391bb6d24f04af7941 ]
The driver is exiting from the fault watchdog thread if it sees the 0xF002
(Soft reset in progress) fault code.
If the driver initiates the soft reset, then the driver restarts the
watchdog at the end of the soft reset completion. However, if the soft
reset is initiated by the firmware asynchronously, then the driver will
never restart the watchdog and never re-initialize the controller after the
asynchronous soft reset completion.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20230331122317.11391-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f0aa59a33d2ac2267d260fe21eaf92500df8e7b4 ]
Some USB-SATA adapters have broken behavior when an unsupported VPD page is
probed: Depending on the VPD page number, a 4-byte header with a valid VPD
page number but with a 0 length is returned. Currently, scsi_vpd_inquiry()
only checks that the page number is valid to determine if the page is
valid, which results in receiving only the 4-byte header for the
non-existent page. This error manifests itself very often with page 0xb9
for the Concurrent Positioning Ranges detection done by sd_read_cpr(),
resulting in the following error message:
sd 0:0:0:0: [sda] Invalid Concurrent Positioning Ranges VPD page
Prevent such misleading error message by adding a check in
scsi_vpd_inquiry() to verify that the page length is not 0.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Link: https://lore.kernel.org/r/20230322022211.116327-1-damien.lemoal@opensource.wdc.com
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0808ed6ebbc292222ca069d339744870f6d801da ]
If crash_dump_buf is not allocated then crash dump can't be available.
Replace logical 'and' with 'or'.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20230324135249.9733-1-thenzl@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c8e22b7a1694bb8d025ea636816472739d859145 upstream.
This reverts commit 3fe97ff3d949 ("scsi: ses: Don't attach if enclosure
has no components") and introduces proper handling of case where there are
no detected secondary components, but primary component (enumerated in
num_enclosures) does exist. That fix was originally proposed by Ding Hui
<dinghui@sangfor.com.cn>.
Completely ignoring devices that have one primary enclosure and no
secondary one results in ses_intf_add() bailing completely
scsi 2:0:0:254: enclosure has no enumerated components
scsi 2:0:0:254: Failed to bind enclosure -12ven in valid configurations such
even on valid configurations with 1 primary and 0 secondary enclosures as
below:
# sg_ses /dev/sg0
3PARdata SES 3321
Supported diagnostic pages:
Supported Diagnostic Pages [sdp] [0x0]
Configuration (SES) [cf] [0x1]
Short Enclosure Status (SES) [ses] [0x8]
# sg_ses -p cf /dev/sg0
3PARdata SES 3321
Configuration diagnostic page:
number of secondary subenclosures: 0
generation code: 0x0
enclosure descriptor list
Subenclosure identifier: 0 [primary]
relative ES process id: 0, number of ES processes: 1
number of type descriptor headers: 1
enclosure logical identifier (hex): 20000002ac02068d
enclosure vendor: 3PARdata product: VV rev: 3321
type descriptor header and text list
Element type: Unspecified, subenclosure id: 0
number of possible elements: 1
The changelog for the original fix follows
=====
We can get a crash when disconnecting the iSCSI session,
the call trace like this:
[ffff00002a00fb70] kfree at ffff00000830e224
[ffff00002a00fba0] ses_intf_remove at ffff000001f200e4
[ffff00002a00fbd0] device_del at ffff0000086b6a98
[ffff00002a00fc50] device_unregister at ffff0000086b6d58
[ffff00002a00fc70] __scsi_remove_device at ffff00000870608c
[ffff00002a00fca0] scsi_remove_device at ffff000008706134
[ffff00002a00fcc0] __scsi_remove_target at ffff0000087062e4
[ffff00002a00fd10] scsi_remove_target at ffff0000087064c0
[ffff00002a00fd70] __iscsi_unbind_session at ffff000001c872c4
[ffff00002a00fdb0] process_one_work at ffff00000810f35c
[ffff00002a00fe00] worker_thread at ffff00000810f648
[ffff00002a00fe70] kthread at ffff000008116e98
In ses_intf_add, components count could be 0, and kcalloc 0 size scomp,
but not saved in edev->component[i].scratch
In this situation, edev->component[0].scratch is an invalid pointer,
when kfree it in ses_intf_remove_enclosure, a crash like above would happen
The call trace also could be other random cases when kfree cannot catch
the invalid pointer
We should not use edev->component[] array when the components count is 0
We also need check index when use edev->component[] array in
ses_enclosure_data_process
=====
Reported-by: Michal Kolar <mich.k@seznam.cz>
Originally-by: Ding Hui <dinghui@sangfor.com.cn>
Cc: stable@vger.kernel.org
Fixes: 3fe97ff3d949 ("scsi: ses: Don't attach if enclosure has no components")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2304042122270.29760@cbobk.fhfr.pm
Tested-by: Michal Kolar <mich.k@seznam.cz>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 48b19b79cfa37b1e50da3b5a8af529f994c08901 ]
The validity of sock should be checked before assignment to avoid incorrect
values. Commit 57569c37f0ad ("scsi: iscsi: iscsi_tcp: Fix null-ptr-deref
while calling getpeername()") introduced this change which may lead to
inconsistent values of tcp_sw_conn->sendpage and conn->datadgst_en.
Fix the issue by moving the position of the assignment.
Fixes: 57569c37f0ad ("scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername()")
Signed-off-by: Zhong Jinghua <zhongjinghua@huawei.com>
Link: https://lore.kernel.org/r/20230329071739.2175268-1-zhongjinghua@huaweicloud.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 85ade4010e13ef152ea925c74d94253db92e5428 ]
There is a memory leak reported by kmemleak:
unreferenced object 0xffffc900003f0000 (size 12288):
comm "modprobe", pid 19117, jiffies 4299751452 (age 42490.264s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000629261a8>] __vmalloc_node_range+0xe56/0x1110
[<0000000001906886>] __vmalloc_node+0xbd/0x150
[<000000005bb4dc34>] vmalloc+0x25/0x30
[<00000000a2dc1194>] qla2x00_create_host+0x7a0/0xe30 [qla2xxx]
[<0000000062b14b47>] qla2x00_probe_one+0x2eb8/0xd160 [qla2xxx]
[<00000000641ccc04>] local_pci_probe+0xeb/0x1a0
The root cause is traced to an error-handling path in qla2x00_probe_one()
when the adapter "base_vha" initialize failed. The fab_scan_rp "scan.l" is
used to record the port information and it is allocated in
qla2x00_create_host(). However, it is not released in the error handling
path "probe_failed".
Fix this by freeing the memory of "scan.l" when an error occurs in the
adapter initialization process.
Fixes: a4239945b8ad ("scsi: qla2xxx: Add switch command to simplify fabric discovery")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230325110004.363898-1-lizetao1@huawei.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d684a7a26f7d2c7122a4581ac966ed64e88fb29c ]
_base_allocate_sense_dma_pool() already prints out the sense pool
information, so don't print it a second time after calling it in
_base_allocate_memory_pools(). In addition the version in
_base_allocate_memory_pools() was using the wrong size value, sz, which was
last assigned when doing some nvme calculations instead of sense_sz to
determine the pool size in kilobytes.
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Fixes: 970ac2bb70e7 ("scsi: mpt3sas: Force sense buffer allocations to be within same 4 GB region")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20230324193204.567932-1-jsnitsel@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2309df27111a51734cb9240b4d3c25f2f3c6ab06 ]
When a physical disk is attached directly "without JBOD MAP support" (see
megasas_get_tm_devhandle()) then there is no real error handling in the
driver. Return FAILED instead of SUCCESS.
Fixes: 18365b138508 ("megaraid_sas: Task management support")
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20230324150134.14696-1-thenzl@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
