| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 2e7e9c0c1ec05f18d320ecc8a31eec59d2af1af9 ]
NVMe Asynchronous Event Request commands have no command timeout value per
specifications.
Set WQE option to allow a reduced FLUSH polling rate for I/O error
detection specifically for nvme_admin_async_event commands.
Link: https://lore.kernel.org/r/20220603174329.63777-9-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 24e1f056677eefe834d5dcf61905cce857ca4b19 upstream.
Refactoring and consolidation of abort paths:
- lpfc_sli4_abort_fcp_cmpl() and lpfc_sli_abort_fcp_cmpl() are combined
into a single generic lpfc_sli_abort_fcp_cmpl() routine. Thus, remove
extraneous lpfc_sli4_abort_fcp_cmpl() prototype declaration.
- lpfc_nvme_abort_fcreq_cmpl() abort completion routine is called with a
mismatched argument type. This may result in misleading log message
content. Update to the correct argument type of lpfc_iocbq instead of
lpfc_wcqe_complete. The lpfc_wcqe_complete should be derived from the
lpfc_iocbq structure.
Link: https://lore.kernel.org/r/20220603174329.63777-3-jsmart2021@gmail.com
Fixes: 31a59f75702f ("scsi: lpfc: SLI path split: Refactor Abort paths")
Cc: <stable@vger.kernel.org> # v5.18
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When injecting EEH errors the port is getting hung up waiting on the node
list to empty, message number 0233. The driver is stuck at this point and
also can't unload. The driver makes transport remoteport delete calls which
try to abort I/O's, but the EEH daemon has already called the driver to
detach and the detachment has set the global FC_UNLOADING flag. There are
several code paths that will avoid I/O cleanup if the FC_UNLOADING flag is
set, resulting in transports waiting for I/O while the driver is waiting on
transports to clean up.
Additionally, during study of the list, a locking issue was found in
lpfc_sli_abort_iocb_ring that could corrupt the list.
A special case was added to the lpfc_cleanup() routine to call
lpfc_sli_flush_rings() if the driver is FC_UNLOADING and if the pci-slot
is offline (e.g. EEH).
The SLI4 part of lpfc_sli_abort_iocb_ring() is changed to use the
ring_lock. Also added code to cancel the I/Os if the pci-slot is offline
and added checks and returns for the FC_UNLOADING and HBA_IOQ_FLUSH flags
to prevent trying to send an I/O that we cannot handle.
Link: https://lore.kernel.org/r/20220317032737.45308-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Following EEH errors, the driver can crash or hang when deleting the
localport or when attempting to unload.
The EEH handlers in the driver did not notify the NVMe-FC transport before
tearing the driver down. This was delayed until the resume steps. This
worked for SCSI because lpfc_block_scsi() would notify the
scsi_fc_transport that the target was not available but it would not clean
up all the references to the ndlp.
The SLI3 prep for dev reset handler did the lpfc_offline_prep() and
lpfc_offline() calls to get the port stopped before restarting. The SLI4
version of the prep for dev reset just destroyed the queues and did not
stop NVMe from continuing. Also because the port was not really stopped
the localport destroy would hang because the transport was still waiting
for I/O. Additionally, a devloss tmo can fire and post events to a stopped
worker thread creating another hang condition.
lpfc_sli4_prep_dev_for_reset() is modified to call lpfc_offline_prep() and
lpfc_offline() rather than just lpfc_scsi_dev_block() to ensure both SCSI
and NVMe transports are notified to block I/O to the driver.
Logic is added to devloss handler and worker thread to clean up ndlp
references and quiesce appropriately.
Link: https://lore.kernel.org/r/20220317032737.45308-2-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update copyrights to 2022 for files modified in the 14.2.0.0 patch set.
Link: https://lore.kernel.org/r/20220225022308.16486-18-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch refactors the Abort paths to use SLI-4 as the primary interface.
- Introduce generic lpfc_sli_prep_abort_xri jump table routine
- Consolidate lpfc_sli4_issue_abort_iotag and lpfc_sli_issue_abort_iotag
into a single generic lpfc_sli_issue_abort_iotag routine
- Consolidate lpfc_sli4_abort_fcp_cmpl and lpfc_sli_abort_fcp_cmpl into a
single generic lpfc_sli_abort_fcp_cmpl routine
- Remove unused routine lpfc_get_iocb_from_iocbq
- Conversion away from using SLI-3 iocb structures to set/access fields in
common routines. Use the new generic get/set routines that were added.
This move changes code from indirect structure references to using local
variables with the generic routines.
- Refactor routines when setting non-generic fields, to have both SLI3 and
SLI4 specific sections. This replaces the set-as-SLI3 then translate to
SLI4 behavior of the past.
Link: https://lore.kernel.org/r/20220225022308.16486-15-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, SLI3 and SLI4 data paths use the same lpfc_iocbq structure.
This is a "common" structure but many of the components refer to sli-rev
specific entities which can lead the developer astray as to what they
actually mean, should be set to, or when they should be used.
This first patch prepares the lpfc_iocbq structure so that elements common
to both SLI3 and SLI4 data paths are more appropriately named, making it
clear they apply generically.
Fieldnames based on 'iocb' (sli3) or 'wqe' (sli4) which are actually
generic to the paths are renamed to 'cmd':
- iocb_flag is renamed to cmd_flag
- lpfc_vmid_iocb_tag is renamed to lpfc_vmid_tag
- fabric_iocb_cmpl is renamed to fabric_cmd_cmpl
- wait_iocb_cmpl is renamed to wait_cmd_cmpl
- iocb_cmpl and wqe_cmpl are combined and renamed to cmd_cmpl
- rsvd2 member is renamed to num_bdes due to pre-existing usage
The structure name itself will retain the iocb reference as changing to a
more relevant "job" or "cmd" title induces many hundreds of line changes
for only a name change.
lpfc_post_buffer is also renamed to lpfc_sli3_post_buffer to indicate use
in the SLI3 path only.
Link: https://lore.kernel.org/r/20220225022308.16486-2-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Merge the 5.15/scsi-fixes branch into the staging tree to resolve UFS
conflict reported by sfr.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The PBDE feature, setting payload buffer address explicitly in the WQE so
it doesn't have to be fetched from the SGL, only makes sense when there is
a single buffer for the I/O. When there are multiple buffers it actually
hurts performance as the SGL subsequently has to be fetched.
Rework the SGL logic to only use PBDE when a single buffer.
Link: https://lore.kernel.org/r/20210910233159.115896-14-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Injecting errors on the PCI slot while the driver is handling NVMe I/O will
cause crashes and hangs.
There are several rather difficult scenarios occurring. The main issue is
that the adapter can report a PCI error before or simultaneously to the PCI
subsystem reporting the error. Both paths have different entry points and
currently there is no interlock between them. Thus multiple teardown paths
are competing and all heck breaks loose.
Complicating things is the NVMs path. To a large degree, I/O was able to be
shutdown for a full FC port on the SCSI stack. But on NVMe, there isn't a
similar call. At best, it works on a per-controller basis, but even at the
controller level, it's a controller "reset" call. All of which means I/O is
still flowing on different CPUs with reset paths expecting hw access
(mailbox commands) to execute properly.
The following modifications are made:
- A new flag is set in PCI error entrypoints so the driver can track being
called by that path.
- An interlock is added in the SLI hw error path and the PCI error path
such that only one of the paths proceeds with the teardown logic.
- RPI cleanup is patched such that RPIs are marked unregistered w/o mbx
cmds in cases of hw error.
- If entering the SLI port re-init calls, a case where SLI error teardown
was quick and beat the PCI calls now reporting error, check whether the
SLI port is still live on the PCI bus.
- In the PCI reset code to bring the adapter back, recheck the IRQ
settings. Different checks for SLI3 vs SLI4.
- In I/O completions, that may be called as part of the cleanup or
underway just before the hw error, check the state of the adapter. If
in error, shortcut handling that would expect further adapter
completions as the hw error won't be sending them.
- In routines waiting on I/O completions, which may have been in progress
prior to the hw error, detect the device is being torn down and abort
from their waits and just give up. This points to a larger issue in the
driver on ref-counting for data structures, as it doesn't have
ref-counting on q and port structures. We'll do this fix for now as it
would be a major rework to be done differently.
- Fix the NVMe cleanup to simulate NVMe I/O completions if I/O is being
failed back due to hw error.
- In I/O buf allocation, done at the start of new I/Os, check hw state and
fail if hw error.
Link: https://lore.kernel.org/r/20210910233159.115896-10-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In a rarely executed path, FLOGI failure, there is a refcounting error. If
FLOGI completed with an error, typically a timeout, the initial completion
handler would remove the job reference. However, the job completion isn't
the actual end of the job/exchange as the timeout usually initiates an
ABTS, and upon that ABTS completion, a final completion is sent. The driver
removes the reference again in the final completion. Thus the imbalance.
In the buggy cases, if there was a link bounce while the delayed response
is outstanding, the fport node may be referenced again but there was no
additional reference as it is already present. The delayed completion then
occurs and removes the last reference freeing the node and causing issues
in the link up processed that is using the node.
Fix this scenario by removing the snippet that removed the reference in the
initial FLOGI completion. The bad snippet was poorly trying to identify the
FLOGI as OK to do so by realizing the node was not registered with either
SCSI or NVMe transport.
Link: https://lore.kernel.org/r/20210910233159.115896-3-jsmart2021@gmail.com
Fixes: 618e2ee146d4 ("scsi: lpfc: Fix FLOGI failure due to accessing a freed node")
Cc: <stable@vger.kernel.org> # v5.13+
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The Kernel test robot flagged the following warning:
".../lpfc_init.c:7788:35: error: 'struct lpfc_sli4_hba' has no member
named 'c_stat'"
Reviewing this issue highlighted that one of the recent patches caused the
driver to no longer compile cleanly if CONFIG_DEBUG_FS is not set.
Correct the different areas that are failing to compile.
Link: https://lore.kernel.org/r/20210908050927.37275-1-jsmart2021@gmail.com
Fixes: 02243836ad6f ("scsi: lpfc: Add support for the CM framework")
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Build-tested-by: Nathan Chancellor <nathan@kernel.org>
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Complete the enablement of the cm framework feature in the adapter. Perform
the following:
- Detect the presence of the congestion management framework feature.
When the cm framework is present:
- Issue the SET_FEATURE command to enable the feature.
- Register the cm statistics buffer with the adapter.
- Read the cm enablement buffer to determine the cm framework state for cm
management.
When cm management is enabled:
- Monitor all FPIN and congestion signalling events, incrementing
counters.
- Regularly sync with the adapter to communicate congestion events and to
receive an rx request limit.
- Monitor requests for rx data and ensure that no more than the
adapter prescribed limit is issued on the link. If the limit is
exceeded, SCSI and/or NVMe traffic is temporarily suspended.
- Maintain the minute, hourly, daily statistics buffer.
- Monitor for congestion enablement change events, causing a reread of the
enablement buffer and acting on any change in enablement.
And:
- Add teardown logic, including buffer deregistration, on adapter
detachment or reset.
Link: https://lore.kernel.org/r/20210816162901.121235-10-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
On an RSCN event, the nodes specified in RSCN payload and in MAPPED state
are moved to NPR state in order to revalidate the login. This triggers an
immediate unregister from SCSI/NVMe backend. The assumption is that the
node may be missing. The re-registration with the backend happens after
either relogin (PLOGI/PRLI; if ADISC is disabled or login truly lost) or
when ADISC completes successfully (rediscover with ADISC enabled).
However, the NVMe-FC standard provides for an RSCN to be triggered when
the remote port supports a discovery controller and there was a change
of discovery log content. As the remote port typically also supports
storage subsystems, this unregister causes all storage controller
connections to fail and require reconnect.
Correct by reworking the code to ensure that the unregistration only occurs
when a login state is truly terminated, thereby leaving the NVMe storage
controllers in place.
The changes made are:
- Retain node state in ADISC_ISSUE when scheduling ADISC ELS retry.
- Do not clear wwpn/wwnn values upon ADISC failure.
- Move MAPPED nodes to NPR during RSCN processing, but do not unregister
with transport. On GIDFT completion, identify missing nodes (not marked
NLP_NPR_2B_DISC) and unregister them.
- Perform unregistration for nodes that will go through ADISC processing
if ADISC completion fails.
- Successful ADISC completion will move node back to MAPPED state.
Link: https://lore.kernel.org/r/20210707184351.67872-16-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When processing an NVMe ERSP IU which didn't match the optimized CQE-only
path, the status was being left to the WQE status. WQE status is non-zero
as it is indicating a non-optimized completion that needs to be handled by
the driver.
Fix by clearing the status field when falling into the non-optimized
case. Log message added to track optimized vs non-optimized debug.
Link: https://lore.kernel.org/r/20210514195559.119853-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Code inspection showed lpfc was using three different pointer formats when
logging discovery object pointers.
Standardize the pointer format to x%px.
Note: %px use is limited to discovery objects in order to aid core
analysis.
Link: https://lore.kernel.org/r/20210412013127.2387-14-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvme.c:2021: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_create_localport'
Link: https://lore.kernel.org/r/20210312094738.2207817-16-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For the files modified in 2021 via the 12.8.0.7 and 12.8.0.8 patch sets,
update the copyright for 2021.
Link: https://lore.kernel.org/r/20210301171821.3427-23-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, ibmvfc,
qla2xxx, hisi_sas, pm80xx) plus the removal of the gdth driver (which
is bound to cause conflicts with a trivial change somewhere).
The only big major rework of note is the one from Hannes trying to
clean up our result handling code in the drivers to make it
consistent"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (194 commits)
scsi: MAINTAINERS: Adjust to reflect gdth scsi driver removal
scsi: ufs: Give clk scaling min gear a value
scsi: lpfc: Fix 'physical' typos
scsi: megaraid_mbox: Fix spelling of 'allocated'
scsi: qla2xxx: Simplify the calculation of variables
scsi: message: fusion: Fix 'physical' typos
scsi: target: core: Change ASCQ for residual write
scsi: target: core: Signal WRITE residuals
scsi: target: core: Set residuals for 4Kn devices
scsi: hisi_sas: Add trace FIFO debugfs support
scsi: hisi_sas: Flush workqueue in hisi_sas_v3_remove()
scsi: hisi_sas: Enable debugfs support by default
scsi: hisi_sas: Don't check .nr_hw_queues in hisi_sas_task_prep()
scsi: hisi_sas: Remove deferred probe check in hisi_sas_v2_probe()
scsi: lpfc: Add auto select on IRQ_POLL
scsi: ncr53c8xx: Fix typos
scsi: lpfc: Fix ancient double free
scsi: qla2xxx: Fix some memory corruption
scsi: qla2xxx: Remove redundant NULL check
scsi: megaraid: Fix ifnullfree.cocci warnings
...
|
|
In testing, in a configuration with Redfish and native NVMe multipath when
an EEH is injected, a kernel oops is being encountered:
(unreliable)
lpfc_nvme_ls_req+0x328/0x720 [lpfc]
__nvme_fc_send_ls_req.constprop.13+0x1d8/0x3d0 [nvme_fc]
nvme_fc_create_association+0x224/0xd10 [nvme_fc]
nvme_fc_reset_ctrl_work+0x110/0x154 [nvme_fc]
process_one_work+0x304/0x5d
the NBMe transport is issuing a Disconnect LS request, which the driver
receives and tries to post but the work queue used by the driver is already
being torn down by the eeh.
Fix by validating the validity of the work queue before proceeding with the
LS transmit.
Link: https://lore.kernel.org/r/20210127221601.84878-1-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Several errors have occurred where the adapter stops or fails but does not
raise the register values for the driver to detect failure. Thus driver is
unaware of the failure. The failure typically results in I/O timeouts, the
I/O timeout handler failing (after several seconds), and the error handler
escalating recovery policy and resulting in more errors. Eventually, the
driver is in a position where things have spiraled and it can't do recovery
because other recovery ops are still outstanding and it becomes unusable.
Resolve the situation by having the I/O timeout handler (actually a els,
SCSI I/O, NVMe ls, or NVMe I/O timeout), in addition to aborting the I/O,
perform a mailbox command and look for a response from the hardware. If
the mailbox command fails, it will mark the adapter offline and then invoke
the adapter reset handler to clean up.
The new I/O timeout test will be limited to a test every 5s. If there are
multiple I/O timeouts concurrently, only the 1st I/O timeout will generate
the mailbox command. Further testing will only occur once a timeout occurs
after a 5s delay from the last mailbox command has expired.
Link: https://lore.kernel.org/r/20210104180240.46824-14-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If a mailbox command times out, the SLI port is deemed in error and the
port is reset. The HBA cleanup is not returning I/Os to the NVMe layer
before the port is unregistered. This is due to the HBA being marked
offline (!SLI_ACTIVE) and cleanup being done by the mailbox timeout handler
rather than an general adapter reset routine. The mailbox timeout handler
mailbox handler only cleaned up SCSI I/Os.
Fix by reworking the mailbox handler to:
- After handling the mailbox error, detect the board is already in
failure (may be due to another error), and leave cleanup to the
other handler.
- If the mailbox command timeout is initial detector of the port error,
continue with the board cleanup and marking the adapter offline
(!SLI_ACTIVE). Remove the SCSI-only I/O cleanup routine. The generic
reset adapter routine that is subsequently invoked, will clean up the
I/Os.
- Have the reset adapter routine flush all NVMe and SCSI I/Os if the
adapter has been marked failed (!SLI_ACTIVE).
- Rework the NVMe I/O terminate routine to take a status code to fail the
I/O with and update so that cleaned up I/O calls the wqe completion
routine. Currently it is bypassing the wqe cleanup and calling the NVMe
I/O completion directly. The wqe completion routine will take care of
data structure and node cleanup then call the NVMe I/O completion
handler.
Link: https://lore.kernel.org/r/20210104180240.46824-11-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When lpfc generates a GEN_REQUEST wqe for the nvme LS (such as Create
Association), the timeout is set to R_A_TOV without regard to the timeout
value supplied by the nvme-fc transport. The driver should be setting the
timeout to the value passed into the routine. Additionally the caller
should be setting the timeout value to the value in the ls request set by
the nvme transport. Instead, it unconditionally is setting it to a driver
defined value. So the driver actually overrode the value twice.
Fix by using the timeout provided to the routine, and for the caller, set
the timeout to the ls request timeout value.
Link: https://lore.kernel.org/r/20210104180240.46824-6-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update Copyright in files changed by the 12.8.0.6 patch set to 2020
Link: https://lore.kernel.org/r/20201115192646.12977-18-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch reworks the abort interfaces such that SLI-3 retains the
iocb-based formatting and completions and SLI-4 now uses native WQEs and
completion routines.
The following changes are made:
- The code is refactored from a confusing 2 routine sequence of
xx_abort_iotag_issue(), which creates/formats and abort cmd, and
xx_issue_abort_tag(), which then issues and handles the completion of
the abort cmd - into a single interface of xx_issue_abort_iotag(). The
new interface will determine whether SLI-3 or SLI-4 and then call the
appropriate handler. A completion handler can now be specified to
address the differences in completion handling. Note: original code is
all iocb based, with SLI-4 converting to SLI-3 for the SCSI/ELS path,
and NVMe natively using wqes.
- The SLI-3 side is refactored:
The older iocb-base lpfc_sli_issue_abort_iotag() routine is combined
with the logic of lpfc_sli_abort_iotag_issue() as well as the
iocb-specific code in lpfc_abort_handler() and lpfc_sli_abort_iocb() to
create the new single SLI-3 abort routine that formats and issues the
iocb.
- The SLI-4 side is refactored and added to:
The native WQE abort code in NVMe is moved to the new SLI-4
issue_abort_iotag() routine. Items in SCSI that set fields not set by
NVMe is migrated into the new routine. Thus the routine supports NVMe
and SCSI initiators. The nvmet block (target) formats the abort slightly
different (like the old NVMe initiator) thus it has its own prep routine
stolen from NVMe initiator and it retains the current code it has for
issuing the WQE (does not use the commonized routine the initiators
do). SLI-4 completion handlers were also added.
- lpfc_abort_handler now becomes a wrapper that determines whether
SLI-3 or SLI-4 and calls the proper abort handler.
Link: https://lore.kernel.org/r/20201115192646.12977-16-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver is currently using SLI-4 WQE templates only for NVMe. Refactor
the template and the placement of the service routine so that it can be
used by both SCSI and NVMe.
Link: https://lore.kernel.org/r/20201115192646.12977-12-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation of reworking the driver to use a native SLI-4 WQE interface
for the SCSI and NVMe I/O paths, start by commonizing the WQE exchange type
and command type attributes.
While adjusting these options also noted the variance in the pbde field.
Fix this by setting templates to 0 and in NVMe, which explicitly uses this
option, setting the value.
Link: https://lore.kernel.org/r/20201115192646.12977-11-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently the discovery layers within the driver use the SCSI midlayer
host_lock to access node-specific structures. This can contend with the I/O
path and is too coarse of a lock.
Rework the driver so that it uses a lock specific to the remote port node
structure when accessing the structure contents. A few of the changes
brought out spots were some slightly reorganized routines worked better.
Link: https://lore.kernel.org/r/20201115192646.12977-6-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Due to bug history and code review, the node reference counting approach in
the driver isn't implemented consistently with how the scsi and nvme
transport perform registrations and unregistrations and their callbacks.
This resulted in many bad/stale node pointers.
Reword the driver so that reference handling is performed as follows:
- The initial node reference is taken on structure allocation
- Take a reference on any add/register call to the transport
- Remove a reference on any delete/unregister call to the transport
- After the node has fully removed from both the SCSI and NVMEe transports
(dev_loss_callbacks have called back) call the discovery engine
DEVICE_RM event which will remove the final reference and release the
node structure.
- Alter dev_loss handling when a vport or base port is unloading.
- Remove the put_node handling - no longer needed.
- Rewrite the vport_delete handling on reference counts. Part of this
effort was driven from the FDISC not registering with the transport and
disrupting the model for node reference counting.
- Deleted lpfc_nlp_remove. Pushed it's remaining ops into
lpfc_nlp_release.
- Several other small code cleanups.
Link: https://lore.kernel.org/r/20201115192646.12977-5-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Now that the driver has gone to a normal ref interface (with no odd logic)
the discovery logic needs to be updated to reworked so that it properly
takes references when it should and give them up when it should.
Rework the driver for the following get/put model:
- Move gets to just before an I/O is issued. Add gets for places where an
I/O was issued without one.
- Ensure that failures from lpfc_nlp_get() are handled by the driver.
- Check and fix the placement of lpfc_nlp_puts relative to io completions.
Note: some of these paths may not release the reference on the exact io
completion as the reference is held as the code takes another step in
the discovery thread and which may cause another io to be issued.
- Rearrange some code for error processing and calling lpfc_nlp_put.
- Fix some places of incorrect reference freeing that was causing the
premature releasing of the structure.
- Nvmet plogi handling performs unreg_rpi's. The reference counts were
unbalanced resulting in premature node removal. In some cases this
caused loss of node discovery. Corrected the reftaking around nvmet
plogis.
Nodes that experience devloss now get released from the node list now that
there is a proper reference taking.
Link: https://lore.kernel.org/r/20201115192646.12977-3-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When a remote port is disconnected and disappears, its node structure
(ndlp) stays allocated and on a vport node list. While on the list it can
be matched, thus requires validation checks on state to be added in
numerous code paths. If the node comes back, its possible for there to be
multiple node structures for the same device on the vport node list. There
is no reason to keep the node structure around after it is no longer in
existence, and the current implementation creates problems for itself
(multiple nodes) and lots of unnecessary code for state validation.
Additionally, the reference taking on the node structure didn't follow the
normal model used by the kernel kref api. It included lots of odd logic to
match state with reference count. The combination of this odd logic plus
the way it was implicitly used in the discovery engine made its reference
taking implementation suspect and extremely hard to follow.
Change the driver such that the reference taking routines are now normal
ref increments/decrements and callout on refcount=0.
With this in place, the rework can be done such that the node structure is
fully removed and deallocated when the remote port no longer exists and all
references are removed. This removal logic, and the basic ref counting are
intrically tied, thus in a single patch.
Link: https://lore.kernel.org/r/20201115192646.12977-2-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvme.c: In function ‘lpfc_nvme_ls_abort’:
drivers/scsi/lpfc/lpfc_nvme.c:943:19: warning: variable ‘phba’ set but not used [-Wunused-but-set-variable]
drivers/scsi/lpfc/lpfc_nvme.c:256: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_create_queue'
drivers/scsi/lpfc/lpfc_nvme.c:804: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:804: warning: Excess function parameter 'nvme_rport' description in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:1312: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1312: warning: Excess function parameter 'lpfcn_cmd' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1416: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1416: warning: Excess function parameter 'lpfcn_cmd' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1594: warning: bad line: indicated in @lpfc_nvme_rport.
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1605: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1852: warning: Function parameter or member 'abts_cmpl' not described in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1852: warning: Excess function parameter 'rspiocb' description in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1888: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:2089: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2089: warning: Function parameter or member 'idx' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2089: warning: Function parameter or member 'expedite' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2193: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_create_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2326: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2326: warning: Excess function parameter 'pnvme' description in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2544: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_rescan_port'
drivers/scsi/lpfc/lpfc_nvme.c:2544: warning: Function parameter or member 'ndlp' not described in 'lpfc_nvme_rescan_port'
Link: https://lore.kernel.org/r/20201102142359.561122-13-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvme.c: In function ‘lpfc_nvme_ls_abort’:
drivers/scsi/lpfc/lpfc_nvme.c:943:19: warning: variable ‘phba’ set but not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20201102142359.561122-11-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The following call trace was seen during HBA reset testing:
BUG: scheduling while atomic: swapper/2/0/0x10000100
...
Call Trace:
dump_stack+0x19/0x1b
__schedule_bug+0x64/0x72
__schedule+0x782/0x840
__cond_resched+0x26/0x30
_cond_resched+0x3a/0x50
mempool_alloc+0xa0/0x170
lpfc_unreg_rpi+0x151/0x630 [lpfc]
lpfc_sli_abts_recover_port+0x171/0x190 [lpfc]
lpfc_sli4_abts_err_handler+0xb2/0x1f0 [lpfc]
lpfc_sli4_io_xri_aborted+0x256/0x300 [lpfc]
lpfc_sli4_sp_handle_abort_xri_wcqe.isra.51+0xa3/0x190 [lpfc]
lpfc_sli4_fp_handle_cqe+0x89/0x4d0 [lpfc]
__lpfc_sli4_process_cq+0xdb/0x2e0 [lpfc]
__lpfc_sli4_hba_process_cq+0x41/0x100 [lpfc]
lpfc_cq_poll_hdler+0x1a/0x30 [lpfc]
irq_poll_softirq+0xc7/0x100
__do_softirq+0xf5/0x280
call_softirq+0x1c/0x30
do_softirq+0x65/0xa0
irq_exit+0x105/0x110
do_IRQ+0x56/0xf0
common_interrupt+0x16a/0x16a
With the conversion to blk_io_poll for better interrupt latency in normal
cases, it introduced this code path, executed when I/O aborts or logouts
are seen, which attempts to allocate memory for a mailbox command to be
issued. The allocation is GFP_KERNEL, thus it could attempt to sleep.
Fix by creating a work element that performs the event handling for the
remote port. This will have the mailbox commands and other items performed
in the work element, not the irq. A much better method as the "irq" routine
does not stall while performing all this deep handling code.
Ensure that allocation failures are handled and send LOGO on failure.
Additionally, enlarge the mailbox memory pool to reduce the possibility of
additional allocation in this path.
Link: https://lore.kernel.org/r/20201020202719.54726-3-james.smart@broadcom.com
Fixes: 317aeb83c92b ("scsi: lpfc: Add blk_io_poll support for latency improvment")
Cc: <stable@vger.kernel.org> # v5.9+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Either due to API slippage before the driver was mainlined or copy/paste
errors.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/lpfc/lpfc_nvme.c:254: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_create_queue'
drivers/scsi/lpfc/lpfc_nvme.c:254: warning: Function parameter or member 'qsize' not described in 'lpfc_nvme_create_queue'
drivers/scsi/lpfc/lpfc_nvme.c:254: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_create_queue'
drivers/scsi/lpfc/lpfc_nvme.c:311: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_delete_queue'
drivers/scsi/lpfc/lpfc_nvme.c:311: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_delete_queue'
drivers/scsi/lpfc/lpfc_nvme.c:689: warning: Function parameter or member 'gen_req_cmp' not described in '__lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Function parameter or member 'pnvme_lsreq' not described in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:801: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_ls_req'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Function parameter or member 'pnvme_lsreq' not described in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:937: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_ls_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Function parameter or member 'phba' not described in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Function parameter or member 'pwqeIn' not described in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Function parameter or member 'wcqe' not described in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1075: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_io_cmd_wqe_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Function parameter or member 'pnode' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Function parameter or member 'cstat' not described in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1313: warning: Excess function parameter 'hw_queue_handle' description in 'lpfc_nvme_prep_io_cmd'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Function parameter or member 'lpfc_ncmd' not described in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1420: warning: Excess function parameter 'hw_queue_handle' description in 'lpfc_nvme_prep_io_dma'
drivers/scsi/lpfc/lpfc_nvme.c:1598: warning: bad line: indicated in @lpfc_nvme_rport.
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1609: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_io_submit'
drivers/scsi/lpfc/lpfc_nvme.c:1856: warning: Function parameter or member 'abts_cmpl' not described in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1856: warning: Excess function parameter 'rspiocb' description in 'lpfc_nvme_abort_fcreq_cmpl'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Function parameter or member 'pnvme_lport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Function parameter or member 'pnvme_rport' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Function parameter or member 'pnvme_fcreq' not described in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Excess function parameter 'lpfc_pnvme' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Excess function parameter 'lpfc_nvme_lport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Excess function parameter 'lpfc_nvme_rport' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:1892: warning: Excess function parameter 'lpfc_nvme_fcreq' description in 'lpfc_nvme_fcp_abort'
drivers/scsi/lpfc/lpfc_nvme.c:2093: warning: Function parameter or member 'ndlp' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2093: warning: Function parameter or member 'idx' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2093: warning: Function parameter or member 'expedite' not described in 'lpfc_get_nvme_buf'
drivers/scsi/lpfc/lpfc_nvme.c:2197: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_create_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2330: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2330: warning: Excess function parameter 'pnvme' description in 'lpfc_nvme_destroy_localport'
drivers/scsi/lpfc/lpfc_nvme.c:2543: warning: Function parameter or member 'vport' not described in 'lpfc_nvme_rescan_port'
drivers/scsi/lpfc/lpfc_nvme.c:2543: warning: Function parameter or member 'ndlp' not described in 'lpfc_nvme_rescan_port'
Link: https://lore.kernel.org/r/20200713080001.128044-21-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
nvme-fc allows the driver to specify a default devloss_tmo value when
registering the remote port. The lpfc driver is currently not doing so,
although it is implementing a driver internal node loss value of 30s which
also is used on the SCSI FC remote port. As no devloss_tmo is set, the
nvme-fc transport defaults to 60s. So there are competing timers.
Additionally, due to the competing timers, it is possible the NVMe rport is
removed but the SCSI rport remains. It is possible that the SCSI FC rport,
which was registered for the NVMe port even if it doesn't utilize the SCSI
protocol, had been tuned to not match either the 60s (nvme-fc default) or
30s (lldd default), it gets out of whack. The lldd will defer to the SCSI
FC rport as long as the SCSI FC rport has not had its devloss_tmo expire.
Correct the situation by specifying a default devloss_tmo to the nvme-fc
transport when registering the rport. Take the value from the SCSI FC
rport if it exists, otherwise use the driver default.
Link: https://lore.kernel.org/r/20200714211412.11773-1-jsmart2021@gmail.com
Tested-by: Martin George <Martin.George@netapp.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The current logging methods typically end up requesting a reproduction with
a different logging level set to figure out what happened. This was mainly
by design to not clutter the kernel log messages with things that were
typically not interesting and the messages themselves could cause other
issues.
When looking to make a better system, it was seen that in many cases when
more data was wanted was when another message, usually at KERN_ERR level,
was logged. And in most cases, what the additional logging that was then
enabled was typically. Most of these areas fell into the discovery machine.
Based on this summary, the following design has been put in place: The
driver will maintain an internal log (256 elements of 256 bytes). The
"additional logging" messages that are usually enabled in a reproduction
will be changed to now log all the time to the internal log. A new logging
level is defined - LOG_TRACE_EVENT. When this level is set (it is not by
default) and a message marked as KERN_ERR is logged, all the messages in
the internal log will be dumped to the kernel log before the KERN_ERR
message is logged.
There is a timestamp on each message added to the internal log. However,
this timestamp is not converted to wall time when logged. The value of the
timestamp is solely to give a crude time reference for the messages.
Link: https://lore.kernel.org/r/20200630215001.70793-14-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
:This series consists of the usual driver updates (qla2xxx, ufs, zfcp,
target, scsi_debug, lpfc, qedi, qedf, hisi_sas, mpt3sas) plus a host
of other minor updates.
There are no major core changes in this series apart from a
refactoring in scsi_lib.c"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (207 commits)
scsi: ufs: ti-j721e-ufs: Fix unwinding of pm_runtime changes
scsi: cxgb3i: Fix some leaks in init_act_open()
scsi: ibmvscsi: Make some functions static
scsi: iscsi: Fix deadlock on recovery path during GFP_IO reclaim
scsi: ufs: Fix WriteBooster flush during runtime suspend
scsi: ufs: Fix index of attributes query for WriteBooster feature
scsi: ufs: Allow WriteBooster on UFS 2.2 devices
scsi: ufs: Remove unnecessary memset for dev_info
scsi: ufs-qcom: Fix scheduling while atomic issue
scsi: mpt3sas: Fix reply queue count in non RDPQ mode
scsi: lpfc: Fix lpfc_nodelist leak when processing unsolicited event
scsi: target: tcmu: Fix a use after free in tcmu_check_expired_queue_cmd()
scsi: vhost: Notify TCM about the maximum sg entries supported per command
scsi: qla2xxx: Remove return value from qla_nvme_ls()
scsi: qla2xxx: Remove an unused function
scsi: iscsi: Register sysfs for iscsi workqueue
scsi: scsi_debug: Parser tables and code interaction
scsi: core: Refactor scsi_mq_setup_tags function
scsi: core: Fix incorrect usage of shost_for_each_device
scsi: qla2xxx: Fix endianness annotations in source files
...
|
|
A static checker reported the following issue:
drivers/scsi/lpfc/lpfc_nvmet.c:1366 lpfc_nvmet_ls_abort()
warn: 'ret' can be either negative or positive
The comment indicates a non-zero value indicates error in the
form of -Exxx, but the code is returning "1".
Fix the code to return -EINVAL to be compliant to comment.
Fixes: e96a22b0b7c2 ("lpfc: Refactor Send LS Abort support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Now that common helpers exist, add the ability to receive NVME LS requests
to the driver. New requests will be delivered to the transport by
nvme_fc_rcv_ls_req().
In order to complete the LS, add support for Send LS Response and send
LS response completion handling to the driver.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Send LS Abort support is needed when Send LS Request is supported.
Currently, the ability to abort an NVME LS request is limited to the nvme
(host) side of the driver. In preparation of both the nvme and nvmet sides
supporting Send LS Abort, rework the existing ls_req abort routines such
that there is common code that can be used by both sides.
While refactoring it was seen the logic in the abort routine was incorrect.
It attempted to abort all NVME LS's on the indicated port. As such, the
routine was reworked to abort only the NVME LS request that was specified.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently, the ability to send an NVME LS request is limited to the nvme
(host) side of the driver. In preparation of both the nvme and nvmet sides
support Send LS Request, rework the existing send ls_req and ls_req
completion routines such that there is common code that can be used by
both sides.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In preparation for supporting both intiator mode and target mode
receiving NVME LS's, commonize the existing NVME LS request receive
handling found in the base driver and in the nvmet side.
Using the original lpfc_nvmet_unsol_ls_event() and
lpfc_nvme_unsol_ls_buffer() routines as a templates, commonize the
reception of an NVME LS request. The common routine will validate the LS
request, that it was received from a logged-in node, and allocate a
lpfc_async_xchg_ctx that is used to manage the LS request. The role of
the port is then inspected to determine which handler is to receive the
LS - nvme or nvmet. As such, the nvmet handler is tied back in. A handler
is created in nvme and is stubbed out.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A lot of files in lpfc include nvme headers, building up relationships that
require a file to change for its headers when there is no other change
necessary. It would be better to localize the nvme headers.
There is also no need for separate nvme (initiator) and nvmet (tgt)
header files.
Refactor the inclusion of nvme headers so that all nvme items are
included by lpfc_nvme.h
Merge lpfc_nvmet.h into lpfc_nvme.h so that there is a single header used
by both the nvme and nvmet sides. This prepares for structure sharing
between the two roles. Prep to add shared function prototypes for upcoming
shared routines.
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The lldd rebinds the ndlp with rport during a nvme rport registration (via
nvme_fc_register_remoteport). If rport & ndlp pointers are same as the
previous one, the lldd will re-use the ndlp and rport association without
re-initialization. This assumption is incorrect. The lldd should be
ignorant of whether the returned rport pointer is new or not, and should
always assume it is new.
Remove the re-binding code, always assumes that rport pointer received from
transport is a new pointer.
Link: https://lore.kernel.org/r/20200501214310.91713-4-jsmart2021@gmail.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During code reviews several instances of duplicate module unloading checks
were found.
Remove the duplicate checks.
Link: https://lore.kernel.org/r/20200421203354.49420-1-jsmart2021@gmail.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull more SCSI updates from James Bottomley:
"This is a batch of changes that didn't make it in the initial pull
request because the lpfc series had to be rebased to redo an incorrect
split.
It's basically driver updates to lpfc, target, bnx2fc and ufs with the
rest being minor updates except the sr_block_release one which fixes a
use after free introduced by the removal of the global mutex in the
first patch set"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (35 commits)
scsi: core: Add DID_ALLOC_FAILURE and DID_MEDIUM_ERROR to hostbyte_table
scsi: ufs: Use ufshcd_config_pwr_mode() when scaling gear
scsi: bnx2fc: fix boolreturn.cocci warnings
scsi: zfcp: use fallthrough;
scsi: aacraid: do not overwrite retval in aac_reset_adapter()
scsi: sr: Fix sr_block_release()
scsi: aic7xxx: Remove more FreeBSD-specific code
scsi: mpt3sas: Fix kernel panic observed on soft HBA unplug
scsi: ufs: set device as active power mode after resetting device
scsi: iscsi: Report unbind session event when the target has been removed
scsi: lpfc: Change default SCSI LUN QD to 64
scsi: libfc: rport state move to PLOGI if all PRLI retry exhausted
scsi: libfc: If PRLI rejected, move rport to PLOGI state
scsi: bnx2fc: Update the driver version to 2.12.13
scsi: bnx2fc: Fix SCSI command completion after cleanup is posted
scsi: bnx2fc: Process the RQE with CQE in interrupt context
scsi: target: use the stack for XCOPY passthrough cmds
scsi: target: increase XCOPY I/O size
scsi: target: avoid per-loop XCOPY buffer allocations
scsi: target: drop xcopy DISK BLOCK LENGTH debug
...
|
|
The original patch was to resolve the lldd being able to be unloaded
while being used to talk to the boot device of the system. However, the
end result of the original patch is that any driver unload while a nvme
controller is live via the lldd is now being prohibited. Given the module
reference, the module teardown routine can't be called, thus there's no
way, other than manual actions to terminate the controllers.
Fixes: 863fbae929c7 ("nvme_fc: add module to ops template to allow module references")
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Currently driver ktime stats, measuring code paths, is NVME-specific.
Convert the stats routines such that the code paths are generic, providing
status for NVME and SCSI. Added ktime stat calls in SCSI queuecommand and
cmpl routines.
Link: https://lore.kernel.org/r/20200322181304.37655-11-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
