summaryrefslogtreecommitdiff
path: root/drivers/rtc/rtc-pcf85063.c
AgeCommit message (Collapse)AuthorFilesLines
2019-04-04rtc: pcf85063: add RTC_VL_READ/RTC_VL_CLR supportAlexandre Belloni1-0/+35
Allow reading the oscillator status bit. Also allow clearing it even if that makes little sense and can't be done in a race free way. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-04rtc: pcf85063: add offset correction supportAlexandre Belloni1-1/+57
The PCF850363 has an offset correction with two modes: With mode 0, the correction is triggered once every two hours and then correction pulses are applied once per minute until the programmed correction values have been implemented. This gives a step of 4.34 ppm. With mode 1, the correction is triggered once every four minutes and then correction pulses are applied once per second up to a maximum of 60 pulses. When correction values greater than 60 pulses are used, additional correction pulses are made in the 59 th second. This gives a step of 4.069 ppm. Use the correction closest to the requested value. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-04rtc: pcf85063: add nvram supportAlexandre Belloni1-0/+24
The pcf85063 has one byte of nvram. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-04rtc: pcf85063: add Micro Crystal RV8263 supportAlexandre Belloni1-4/+28
The Micro Crystal RV8263 has the same IC as the pcf85063 but has an on board crystal. This means that the CAP_SEL bit has to be cleared so the correct capacitance is selected for the crystal. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-04rtc: pcf85063: add alarm supportAlexandre Belloni1-0/+121
Add support for the alarms. The match on the weekday is not used as it it not necessarily properly set. The tested RTC shows a behaviour where setting an alarm on the second right after an alarm that fired is not working, probably because of the circuit that ensures an alarm only fires once. This is why uie_unsupported is set. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-04rtc: pcf85063: differentiate pcf85063a and pcf85063tpAlexandre Belloni1-6/+27
As stated in a comment pcf85063a and pcf85063tp don't have the same number of registers. Especially, pcf85063tp doesn't have alarm support. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-04rtc: pcf85063: switch to regmapAlexandre Belloni1-93/+61
Switch to regmap to simplify register accesses and remove the need for pcf85063_stop_clock/pcf85063_start_clock. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-04rtc: pcf85063: set rangeAlexandre Belloni1-3/+2
This is a standard BCD RTC that will fail in 2100. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-04rtc: pcf85063: convert to devm_rtc_allocate_deviceAlexandre Belloni1-6/+6
This allows further improvement of the driver. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-04rtc: pcf85063: remove bogus i2c functionality checkAlexandre Belloni1-3/+0
Only smbus reads and write are done in the driver, plain i2c functionality is not required. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-04rtc: pcf85063: convert to SPDX identifierAlexandre Belloni1-6/+1
Use SPDX-License-Identifier instead of a verbose license text. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-04-04rtc: pcf85063: switch to probe_newAlexandre Belloni1-10/+2
struct i2c_device_id argument of probe() is not used, so use probe_new() instead. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-03-02rtc: pcf85063: remove dead codeAlexey Roslyakov1-7/+0
Some of defines are not in use since 7b5768486a910532885f01b9d2dad4818c8b3be1. Remove it to make the code easier to read and understand. Signed-off-by: Alexey Roslyakov <alexey.roslyakov@gmail.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-01-22rtc: pcf85063: set xtal load capacitance from DTSam Ravnborg1-0/+39
Add support for specifying the xtal load capacitance in the DT node. The pcf85063 supports xtal load capacitance of 7pF or 12.5pF. If the rtc has the wrong configuration the time will drift several hours/week. The driver use the default value 7pF. The DT may specify either 7000fF or 12500fF. (The DT uses femto Farad to avoid decimal numbers). Other values are warned and the driver uses the default value. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Urs Fässler <urs.fassler@bbv.ch> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-07-28rtc: pcf85063: preserve control register value between stop and startAlvin Šipraga1-10/+11
Fix a bug that caused the Control_1 register to get zeroed whenever the RTC time is set. The problem occurred between stopping and starting the RTC clock, wherein the return value of a successful I2C write function would get written to the register. Also update variables of the start and stop functions to be more consistent with the rest of the driver. Signed-off-by: Alvin Šipraga <alvin@airtame.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-03-17rtc: pcf85063: fix clearing bits in pcf85063_start_clockMichael McCormick1-1/+1
Bit clear operation was missing ~ Signed-off-by: Michael McCormick <michael.mccormick@enatel.net> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-03-17rtc: pcf85063: remove useless indirectionAlexandre Belloni1-12/+4
pcf85063_get_datetime and pcf85063_set_datetime are only used after casting dev to an i2c_client. Remove that useless indirection. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-03-17rtc: pcf85063: stop validating rtc_time in .read_timeAlexandre Belloni1-1/+1
The RTC core is always calling rtc_valid_tm after the read_time callback. It is not necessary to call it before returning from the callback. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2016-11-05rtc: pcf85063: do not register a RTC device if chip is not presentMirza Krak1-0/+7
Add a sanity check to see if chip is present. If we can not communicate with the chip there is no point in registering a RTC device. Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-07-19rtc: pcf85063: Add support for the PCF85063A deviceChris DeBruin1-9/+38
The current rtc-pcf85063 driver only supports the PCF85063TP device. Using the existing driver on a PCF85063A will result in the time being set correctly into the RTC, but the RTC is held in the stopped state. Therefore, the time will no longer advance and no error is indicated. The PCF85063A device has a bigger memory map than the PCF85063TP. The existing driver make use of an address rollover condition, but the rollover point is different in the two devices. Signed-off-by: Chris DeBruin <cdeb5783@gmail.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-07-19rtc: pcf85063: fix year rangeAlexandre Belloni1-7/+5
The year range is not validated properly As the driver has been mainlined in 2014, it is not an issue to stop handling dates between 1970 and 2000 with the benefit of handling dates up to 2100. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-03-14rtc: pcf85063: remove struct pcf85063Alexandre Belloni1-17/+5
No members of struct pcf85063 are used anymore, remove the whole structure. Reviewed-by: Juergen Borleis <jbe@pengutronix.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-03-14rtc: pcf85063: remove useless DRV_VERSIONAlexandre Belloni1-5/+0
Since the driver is mainlined there is no use for a separate version number. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-03-14rtc: pcf85063: remove useless century handlingAlexandre Belloni1-7/+0
pcf85063_get_datetime() tries to handle a century bit but that bit is not documented and the final value is never used anywhere else in the kernel. Reviewed-by: Juergen Borleis <jbe@pengutronix.de> Tested-by: Ulrich Ölmann <u.oelmann@pengutronix.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-03-14rtc: pcf85063: fix time/date settingJuergen Borleis1-23/+55
When setting a new time/date the RTC's clock must be stopped first, in order to write the time/date registers in an atomic manner. So, this change stops the clock first and then writes the time/date registers and the clock control register (to re-enable the clock) in one turn. Signed-off-by: Juergen Borleis <jbe@pengutronix.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-03-14rtc: pcf85063: fix time/date readingJuergen Borleis1-0/+7
Check if the RTC signals an invalid time/date (due to a battery power loss for example). In this case ignore the time/date until it is really set again. Signed-off-by: Juergen Borleis <jbe@pengutronix.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-03-14rtc: pcf85063: simplify code to read the current timeJuergen Borleis1-26/+21
By using i2c_smbus_read_i2c_block_data() the code is now much simpler. While at it: when reading the RTC's seconds register, all time/date registers are frozen until the RTC's year register is read. So it is important to read all time/date registers in one turn to not lose a second event. Make it more clear why the read must happen in this way. Signed-off-by: Juergen Borleis <jbe@pengutronix.de> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-11-08rtc: pcf85063: return an error when date is invalidAlexandre Belloni1-7/+1
Return an error when the date is invalid as the policy should be implemented there. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-09-05rtc: Drop owner assignment from i2c_driverKrzysztof Kozlowski1-1/+0
i2c_driver does not need to set an owner because i2c_register_driver() will set it. Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2014-08-09rtc: add pcf85063 supportSøren Andersen1-0/+204
Add support for the pcf85063 rtc chip. [akpm@linux-foundation.org: fix comment typo, tweak conding style] Signed-off-by: Soeren Andersen <san@rosetechnology.dk> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-11-08 10:04:09 +0300