| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This round contains a couple of new drivers for the Marvell Berlin
family of SoCs, various SoCs from Renesas and Broadcom as well as the
backlight PWM present on MediaTek SoCs.
Further existing drivers are extended to support a wider range of
hardware.
The remaining patches are minor fixes and cleanups across the board.
Note that one of the patches included in this pull request is against
arch/unicore32. I've included it here because I couldn't get a
response from Guan Xuetao and I consider the change low-risk.
Equivalent patches have been merged and tested in Samsung and PXA
trees. The goal is to finally get rid of legacy code paths that have
repeatedly been causing headaches"
* tag 'pwm/for-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (24 commits)
pwm: sunxi: Fix whitespace issue
pwm: sysfs: Make use of the DEVICE_ATTR_[RW][WO] macro's
pwm: sysfs: Remove unnecessary temporary variable
unicore32: nb0916: Use PWM lookup table
pwm: pwm-rcar: Revise the device tree binding document about compatible
pwm: Return -ENODEV if no PWM lookup match is found
pwm: sun4i: Add support for PWM controller on sun5i SoCs
pwm: Set enable state properly on failed call to enable
pwm: lpss: Add support for runtime PM
pwm: lpss: Add more Intel Broxton IDs
pwm: lpss: Support all four PWMs on Intel Broxton
pwm: lpss: Add support for multiple PWMs
pwm-pca9685: enable ACPI device found on Galileo Gen2
pwm: Add MediaTek display PWM driver support
dt-bindings: pwm: Add MediaTek display PWM bindings
pwm: tipwmss: Enable on TI DRA7x and AM437x
pwm: atmel-hlcdc: add sama5d2 SoC support.
pwm: Add Broadcom BCM7038 PWM controller support
Documentation: dt: add Broadcom BCM7038 PWM controller binding
pwm: Add support for R-Car PWM Timer
...
|
|
This patch changes no code, it just fixes the whitespacing. Operators
should be separated from operands by a single space.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
For the npwm property the PWM sysfs interface already made use of the
DEVICE_ATTR_RO macro. This patch expands this to the other sysfs
properties so that the code base is concise and makes use of this
helpful macro.
This has the advantage of slightly reducing the code size, improving
readability and no longer using magic values for permissions.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Use the result of pwm_is_enabled() directly instead of storing it in a
temporary variable.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
When looking up a PWM using the lookup table, assume that all entries
will have been added already, so failure to find a match means that no
corresponding entry has been registered.
This fixes an issue where -EPROBE_DEFER would be returned if the PWM
lookup table is empty. After this fix, -EPROBE_DEFER is reserved for
situations where no provider has yet registered for a matching entry.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM controller on sun5i SoCs is identical to the one found on sun7i
SoCs. On the A13 package only one of the 2 pins is routed to the outside,
so only advertise one PWM channel there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The pwm_enable() function didn't clear the enabled bit if a call to the
driver's ->enable() callback returned an error. The result was that the
state of the PWM core was wrong. Clearing the bit when enable returns
an error ensures the state is properly set.
Tested-by: Jonathan Richardson <jonathar@broadcom.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
[thierry.reding@gmail.com: add missing kerneldoc for the lock]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
To be able to save some power when PWM is not in use, add support for
runtime PM for this driver. This also allows the platform to transition to
low power S0ix states when the system is idle.
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add more Intel Broxton ACPI and PCI IDs to the driver supported devices
list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Intel Broxton has similar PWM than Intel Braswell but instead of one it has
four PWMs included in one PCI/ACPI device. This patch adds support for all
the four PWMs and changes the PCI part of the driver to use
'pwm_lpss_bxt_info' instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
New Intel SoCs such as Broxton will have four PWMs per PCI (or ACPI)
device. Each PWM has 1k of register space allocated from the parent device.
Add support for this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
There is a chip connected to i2c bus on Intel Galileo Gen2 board. Enable it via
ACPI ID INT3492.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add display PWM driver support to modify backlight for MT8173 and
MT6595. The PWM has one channel to control the brightness of the
display. When the (high_width / period) is closer to 1, the screen
is brighter; otherwise, it is darker.
Signed-off-by: YH Huang <yh.huang@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
TIPWMSS is present on TI's DRA7x and AM437x SoCs. Enable its usage.
Instead of adding each SoC individually, use the more generic symbol
ARCH_OMAP2PLUS instead.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add sama5d2 hlcdc backlight PWM support. This chip doesn't have to deal with an
errata, so it's a simple addition of the mfd compatible string.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add support for the BCM7038-style PWM controller found in all BCM7xxx STB SoCs.
This controller has a hardcoded 2 channels per controller, and cascades a
variable frequency generator on top of a fixed frequency generator which offers
a range of a 148ns period all the way to ~622ms periods.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Commit dca1a4b5ff6e ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.
Get and use the slow clock as it is necessary for the timer counters.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
|
|
This patch adds support for R-Car SoCs PWM Timer. The PWM timer of
R-Car H2 has 7 channels. So, we can use the channels if we describe
device tree nodes.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add a PWM controller driver for the Marvell Berlin SoCs. This PWM
controller has 4 channels.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
This platform driver has a OF device ID table but the OF module alias
information is not created so module autoloading won't work.
This patch adds the missing MODULE_DEVICE_TABLE() for OF to export that
information so modules have the correct aliases built-in and autoloading
works correctly.
A longer explanation by Javier Canillas can be found here:
https://lkml.org/lkml/2015/7/30/519
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces the beginnings of a new API that's
based around the concept of states that can be atomically applied.
Drivers go to various lengths to implement something similar, which
indicates that the core should really be providing the necessary
framework.
On top of that, there is a bit of cleanup as well as improved
kerneldoc and integration into the device-drivers DocBook.
Regarding drivers there is a new one for the NXP LPC18xx family of
SoCs and a couple of fixes for existing drivers (pca9685, Broadcom
Kona and Atmel HLCDC)"
* tag 'pwm/for-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
ARM: at91: pwm: atmel-hlcdc: Add at91sam9n12 errata
pwm: Add NXP LPC18xx PWM/SCT DT binding documentation
pwm: NXP LPC18xx PWM/SCT driver
pwm-pca9685: Support changing the output frequency
pwm-pca9685: Fix several driver bugs
pwm: kona: Modify settings application sequence
pwm: pca9685: Drop owner assignment
pwm: Add to device-drivers documentation
pwm: Clean up kerneldoc
pwm: Remove useless whitespace
pwm: sysfs: Remove unnecessary padding
pwm: sysfs: Properly convert from enum to string
pwm: Make use of pwm_get_xxx() helpers where appropriate
pwm: Add pwm_get_polarity() helper function
pwm: Constify PWM device where possible
pwm: Add the pwm_is_enabled() helper
|
|
The errata for HLCDC PWM of at91sam9n12 are the same as for at91sam9x5.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
This commit adds support for NXP LPC18xx PWM/SCT.
NXP LPC SoCs family, which includes LPC18xx/LPC43xx, provides a State
Configurable Timer (SCT) which can be configured as a Pulse Width
Modulator. Other SoCs in that family may share the same hardware.
The PWM supports a total of 16 channels, but only 15 can be simultaneously
requested. There's only one period, global to all the channels, thus PWM
driver will refuse setting different values to it, unless there's only one
channel requested.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
[thierry.reding@gmail.com: remove excessive padding of fields]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Previously, period_ns and duty_ns were only used to determine the
ratio of ON and OFF time, the default frequency of 200 Hz was never
changed.
The PCA9685 however is capable of changing the PWM output frequency,
which is expected when changing the period.
This patch configures the prescaler accordingly, using the formula
and notes provided in the PCA9685 datasheet.
Bounds checking for the minimum and maximum frequencies, last updated
in revision v.4 of said datasheet, is also added.
The prescaler is only touched if the period changed, because we have to
put the chip into sleep mode to unlock the prescale register.
If it is changed, the PWM output frequency changes for all outputs,
because there is one prescaler per chip. This is documented in the
PCA9685 datasheet and in the comments.
If the duty cycle is not changed at the same time as the period, then
we restart the PWM output using the duty cycle to period ratio from
before the period change.
When using LEDs for example, previously set brightness levels stay the
same when the frequency changes.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Problems:
- When duty_ns == period_ns, the full OFF bit was not cleared and the
PWM output of the PCA9685 stayed off.
- When duty_ns == period_ns and the catch-all channel was used, the
ALL_LED_OFF_L register was not cleared.
- The full ON bit was not cleared when setting the OFF time, therefore
the exact OFF time was ignored when setting a duty_ns < period_ns
Solution: Clear both OFF registers when setting full ON and clear the
full ON bit when changing the OFF registers.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Update the driver so that settings are applied in accordance with the
most recent version of the hardware spec. The revised sequence clears
the trigger bit, waits 400ns, writes settings, sets the trigger bit,
and waits another 400ns. This corrects an issue where occasionally a
requested change was not properly reflected in the PWM output.
Reviewed-by: Arun Ramamurthy <arunrama@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Clean up kerneldoc in preparation for including the PWM documentation in
DocBook.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Remove useless tabs used for padding in structure definitions as well as
some blank lines.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Padding initializers so that assignment operators align is bound to lead
to inconsistencies or churn. Single spaces around the assignment is just
fine.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The current code will check for polarity in a boolean way. While it is
correct that polarity is either normal or inversed, make it more obvious
that it's an enumeration by using a switch statement and explicit
matches on the enumeration values.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The Crystalcove PMIC provides three PWM signals and this driver exports
one of them on the BYT platform which is used to control backlight for
DSI panel. This is platform device implementation of the drivers/mfd
cell device for CRC PMIC.
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Use the pwm_get_xxx() helpers instead of directly accessing the fields
in struct pwm_device. This will allow us to smoothly move to the atomic
update approach.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Some PWM drivers are testing the PWMF_ENABLED flag. Create a helper
function to hide the logic behind enabled test. This will allow us to
smoothly move from the current approach to an atomic PWM update
approach.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This has a couple of fixes for Atmel, Samsung and Broadcom drivers.
Some preparatory patches for more upcoming Intel work is included as
well"
* tag 'pwm/for-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: lpss: pci: Add support for Broxton platform
pwm: bcm-kona: Don't set polarity in probe
pwm: Add pwmchip_add_with_polarity() API
pwm: atmel: Fix incorrect CDTY value after disabling
pwm: atmel: Fix incorrect CDTY value after enabling
pwm: samsung: Use MODULE_DEVICE_TABLE() to include OF modalias
pwm: Add support to remove registered consumer lookup tables
|
|
Add PCI device IDs for Broxton platform.
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Omit setting the polarity to normal during probe and instead use the new
pwmchip_add_with_polarity() function to register a PWM chip with inverse
polarity by default for all channels to reflect the hardware default.
Signed-off-by: Arun Ramamurthy <arunrama@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
[thierry.reding@gmail.com: use pwmchip_add_with_polarity()]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add a new function to register a PWM chip with channels that have their
initial polarity as specified by an additional parameter. This benefits
drivers of controllers that by default operate with inversed polarity
by removing the need to modify the polarity during initialization.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
[thierry.reding@gmail.com: export pwmchip_add_with_polarity()]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
pwm-leds calls .config() and .disable() in a row. This exhibits that it
may happen that the channel gets disabled before CDTY has been updated
with CUPD. The issue gets quite worse with long periods. So, ensure that
at least one period has past before disabling the channel by polling
ISR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Gaël PORTAY <gael.portay@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
CUPD is not flushed before enabling the channel so it will update
CDTY/CPRD just after one period. So we always set CUPD, even when the
channel is not enabled.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
If the pwm-samsung driver is built as a module, modalias information is
not filled so the module is not autoloaded. Use the MODULE_DEVICE_TABLE()
macro to export the OF device ID so the module contains that information.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM hardware on Pistachio platform has a maximum timebase steps
value to 255. To fix it, let's introduce a compatible-specific
data structure to contain the SoC-specific details and use it to
specify a maximum timebase.
Also, let's limit the minimum timebase to 16 steps, to allow a sane
range of duty cycle steps.
Fixes: 277bb6a29e00 ("pwm: Imagination Technologies PWM DAC driver")
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
In case some drivers are unloading, they can remove lookup tables which
they had registered during their load time to avoid redundant entries if
loaded again.
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
For platforms that don't support DT, some early MFD modules can register
lookup tables. Remove the __init annotation so that this works. This is
similar to gpio_add_lookup_table() which allows late additions.
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
When disabling the Samsung PWM the output state remains at the level it
was at the end of a PWM cycle. In other words, calling pwm_disable()
when at 100% duty cycle will keep the output active, while at all other
settings the output will go/stay inactive. On top of that the Samsung
PWM settings are double-buffered, which means the new settings only get
applied at the start of a new PWM cycle.
This results in a race if the PWM is at 100% duty cycle and a driver
calls:
pwm_config(pwm, 0, period);
pwm_disable(pwm);
In this case the PWMs output will unexpectedly stay active, unless a new
PWM cycle happened to start between the register writes in pwm_config()
and pwm_disable(). As far as I can tell this is a regression introduced
by 3bdf878, before that a call to pwm_config() would call
pwm_samsung_enable() which, while heavy-handed, made sure the expected
settings were live.
To resolve this, while not re-introducing the issues 3bdf878 (flickering
as the PWM got reset while in a PWM cycle) fixed, only force an update
of the settings when at 100% duty cycle, which shouldn't have any
noticeable effect on the output but is enough to ensure the behaviour is
as expected on disable.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The driver computes which clock divider it sould be using from the
requested period. This computation assumes that the link between the
register value and the actual divider value is raising 2 to the power of
the registry value.
div = 1 << regvalue
This is true only for the first 5 values out of 8. Next values are 64,
256 and, 1024 - instead of 32, 64, 128.
This affects only the users requesting a period > 0.04369s.
Replace the computation with a look-up table.
Signed-off-by: Gaetan Hug <ghug@induct.be>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
sama5d4 SoC also has an errata on the HLCDC PWM. It is the same as the
sama5d3 that is forbidding the use of div1 prescaler.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Instead of using the literal value for the number of nanoseconds per
second, use the macro instead to increase readability.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The of_node_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
