| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The N56VB laptop has a round button located on the left side above the
keyboard. Map it to F13 since it does not have any predeterminated
purpose.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
To discover core-power capability, some new mailbox commands are added. Allow
those commands to execute.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add support for new Mellanox system types of basic class VMOD0010,
containing new Mellanox systems equipped with new switch device
Spectrum 3 (32x400GbE/64x200G/128x100G Ethernet switch).
These are the Top of the Rack 1U/2U/4U systems, equipped with
Mellanox Comex card and with the switch board with Mellanox Spectrum-3
device.
This class of devices can be equipped with two PS units for 1U/2U or
with four PS units for 4U systems.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add support for capability register, which contains information about
the number of PS units equipped on the system and about minimum I2C
frequency supported by the all system's I2C devices.
Utilization of this register allows to avoid necessity of providing new
system description, in case it differs in number of PS units or in
minimal I2C frequency.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add support for new Mellanox system types of basic class VMOD0009,
containing Mellanox systems equipped with the switch devices
Spectrum 1 (32x100GbE Ethernet switch) and Switch-IB/Switch-IB2
(36x100Gbe InfiniBand switch).
These are the Top of the Rack system, equipped with Mellanox Comex
card.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Separate assignment for systems mux configuration based on system type,
instead of setting the same configuration for the all.
The motivation is to allow introduction of new systems types with the
different mux topology.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add new attributes for "next-generation" type systems:
- Reset cause indication, when system reset has been caused by the
platform reset request through CPLD, by AC power failure,
by software power off request through CPLD. by signal asserted by SOC
through ACPI register. It introduces more reset causes, which can
be monitored after the reboots.
- Setting and removing system VPD (EEPROM) hardware write protection.
It allows to access VPD during production cycle and prevents VPD
corruption on system in field.
- Voltage regulator devices configuration update status and version. It
allows to monitor configuration update status and current active
version for such sort of devices.
- PCIe ASIC reset disable - when set ASIC will go down upon PCIe
root complex reset, otherwise ASIC will stay up during PCIe root
complex reset.
- System configuration Ids to provide system static topology
identification, like system's static I2C topology, number and type of
FPGA devices within the system and so on.
Add the existing attribute for "iio" bank selection for system type
"msn21xx".
All the above attributes are exposed through "sysfs" by "mlxreg-io"
driver.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Remove redundant semicolons at the end of few functions.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Some server users set limits on the uncore frequency using MSR 620H, while
running latency sensitive workloads. Here uncore frequency controls
RING/LLC(last-level cache) clocks.
But MSR control is not always possible from the user space, so this driver
provides a sysfs interface to set max and min frequency limits. This MSR
620H is a die scoped in multi-die system or package scoped in non multi-die
systems.
When this driver is loaded, a new directory is created under
/sys/devices/system/cpu.
For example on a two package Skylake server:
$cd /sys/devices/system/cpu/intel_uncore_frequency
$ls
package_00_die_00 package_01_die_00
$ls package_00_die_00
max_freq_khz min_freq_khz initial_max_freq_khz
initial_min_freq_khz
$grep . *
max_freq_khz:2400000
min_freq_khz:1200000
initial_max_freq_khz:2400000
initial_min_freq_khz:1200000
Here, initial_max_freq_khz and initial_min_freq_khz are read only
attributes to show power up or initial values of max and min frequencies
respectively. Other attributes are read-write, so that users can modify.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Some of ASUS laptops like UX431FL keyboard backlight cannot be set to
brightness 0. According to ASUS' information, the brightness should be
0x80 ~ 0x83. This patch fixes it by following the logic.
Fixes: e9809c0b9670 ("asus-wmi: add keyboard backlight support")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Fix ambiguous spelling in the comments.
While here, update two lines to fit one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The timeout loop look more naturally when done like
unsigned long timeout = ...;
...
do {
...
if (cond)
return %OK;
sleep(...);
} while (time_before(timeout));
...print timeout error...
return %ERROR;
It also saves LOCs. Convert the driver to this format of timeout loop.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
ASUS TUF FX705DY/FX505DY starts in silent mode and under heavy
CPU load it overheats and drops CPU frequency to 399MHz and stays
at it until reboot [1]. Set throttle thermal policy to default
to avoid overheating and throttlig.
[1] Link: https://bugzilla.kernel.org/show_bug.cgi?id=203733
Signed-off-by: Leonid Maksymchuk <leonmaxx@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Throttle thermal policy ACPI device is used to control CPU cooling and
throttling. This patch adds sysfs entry for setting current mode and
Fn+F5 hotkey that switches to next.
Policy modes:
* 0x00 - default
* 0x01 - overboost
* 0x02 - silent
Signed-off-by: Leonid Maksymchuk <leonmaxx@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
1. Put on one line PROPERTY_ENTRY_STRING("firmware-name", ...) lines. In most
cases this doesn't over the limit, the rest is pretty much obvious from
reading point of view.
2. Put on one line DMI_MATCH() parameters, we already have over the limit lines.
3. Reduce indentation of function parameters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add touchscreen info for the PiPO W11 tablet.
Signed-off-by: Tim Josten <timjosten@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Adding new CML CPU model ID into platform driver support list.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Allow the user to configure the fan to turn on / speed-up at lower
thresholds then before (20 degrees Celcius as minimum instead of 40) and
likewise also allow the user to delay the fan speeding-up till the
temperature hits 90 degrees Celcius (was 70).
Cc: Jason Anderson <jasona.594@gmail.com>
Reported-by: Jason Anderson <jasona.594@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Use our default values when wrong module-parameters are given, instead of
refusing to load. Refusing to load leaves the fan at the BIOS default
setting, which is "Off". The CPU's thermal throttling should protect the
system from damage, but not-loading is really not the best fallback in this
case.
This commit fixes this by re-setting module-parameter values to their
defaults if they are out of range, instead of failing the probe with
-EINVAL.
Cc: stable@vger.kernel.org
Cc: Jason Anderson <jasona.594@gmail.com>
Reported-by: Jason Anderson <jasona.594@gmail.com>
Fixes: 594ce6db326e ("platform/x86: GPD pocket fan: Use a min-speed of 2 while charging")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
This patch corrects the SPDX License Identifier style in
header files related to x86 Platform Specific Drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
kstrtou32_from_user()
kstrtou32_from_user() may return different error codes on certain
circumstances. Respect all possible values.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Fix spelling of MHz unit in a comment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
There are two problematic places where indentation is not good to a reader
and maintainer. Fix them here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
There is a function which is solely used for DebugFS interface,
do not build it otherwise.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
kstrtou32_from_user() may return different error codes on certain
circumstances. Respect all possible values.
While here, move it out of the lock: there is no data access that lock guards.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
While here, drop initialized but unused ssram_base_addr and ssram_size members.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add Intel Elkhart Lake to the list of the platforms that driver supports
for the PMC device.
Just like Ice Lake and Tiger Lake, Elkhart Lake can also reuse all the
Cannon Lake PCH IPs. Also, it uses the same PCH IPs of Tiger Lake, no
additional effort is needed to enable but to simply reuse them.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: David E. Box <david.e.box@intel.com>
Cc: Rajneesh Bhardwaj <irenic.rajneesh@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add Intel Tiger Lake to the list of the platforms that driver supports
for the PMC device.
Just like Ice Lake, Tiger Lake can also reuse all the Cannon Lake PCH
IPs. Since Tiger Lake has almost the same number of PCH IPs as Ice Lake,
reuse Ice Lake's PPFEAR_NUM_ENTRIES instead of defining a new macro.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: David E. Box <david.e.box@intel.com>
Cc: Rajneesh Bhardwaj <irenic.rajneesh@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
pch_ip_power_gating_status conditional
Check if the platform supports and only then add a debugfs entry for PCH
IP power gating status.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: David E. Box <david.e.box@intel.com>
Cc: Rajneesh Bhardwaj <irenic.rajneesh@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The current implementation of intel_pmc_core driver allows to reuse, but does
not reflect the exact number and names of IPs for a newer platform which
does not necessarily support all the IPs in the entries. The names and
number of these IPs might differ from its previous platforms. The number
of PCH IPs per platform is calculated based on PPFEAR_NUM_ENTRIES
defined, where each entry represents a bucket (8 bits). The platform can
support 'n' entries, but not necessarily all 'n * 8' IPs.
Create platform dependent bitmap structures to specify the exact number,
names of IPs while reusing the existing IPs.
The changes in this patch are preparatory to accommodate future SoCs
that might reuse the CNL/ICL PCH IPs, and to reflect the exact number of
IPs with its names.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: David E. Box <david.e.box@intel.com>
Cc: Rajneesh Bhardwaj <irenic.rajneesh@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
There is no need to assign NULL or 0 in the static structures explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
It is common practice to place a comma after the last entry in an
initialized array to avoid the need to add one in future patches that
extend the array. But when the last element is a termination marker, the
comma could be harmful. Any new entries must be added before the
terminator (and the comma would prevent the compiler from issuing a
warning about an entry after the terminator).
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: David E. Box <david.e.box@intel.com>
Cc: Rajneesh Bhardwaj <irenic.rajneesh@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Mainly does:
- capitalize gpio and bios to GPIO and BIOS
- capitalize beginning of comments
- add periods in multi-line comments
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
GPIO stuff on APUv4 seems to be the same as on APUv2, so we just
need to match on DMI data.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The mapping entry has to hold the GPIO line index instead of
controller's register number.
Fixes: 5037d4ddda31 ("platform/x86: pcengines-apuv2: wire up simswitch gpio as led")
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The CONNECT X300 uses the PMC clock for on-board components and gets
stuck during boot if the clock is disabled. Therefore, add this
device to the critical systems list.
Tested on CONNECT X300.
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Signed-off-by: Michael Haener <michael.haener@siemens.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
At least on the HP Envy x360 15-cp0xxx model the WMI interface
for HPWMI_FEATURE2_QUERY requires an outsize of at least 128 bytes,
otherwise it fails with an error code 5 (HPWMI_RET_INVALID_PARAMETERS):
Dec 06 00:59:38 kernel: hp_wmi: query 0xd returned error 0x5
We do not care about the contents of the buffer, we just want to know
if the HPWMI_FEATURE2_QUERY command is supported.
This commits bumps the buffer size, fixing the error.
Fixes: 8a1513b4932 ("hp-wmi: limit hotkey enable")
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1520703
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Tiger Lake has a new unique ACPI device ID for the Intel HID event
filter device that needs to be added to the intel-hid driver to
support it.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
[ rjw: Subject and changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Now that static device properties allow defining reference properties
together with all other types of properties, instead of managing them
separately, let's adjust the driver.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull Documentation updates from Jonathan Corbet:
"Here are the main documentation changes for 5.5:
- Various kerneldoc script enhancements.
- More RST conversions; those are slowing down as we run out of
things to convert, but we're a ways from done still.
- Dan's "maintainer profile entry" work landed at last. Now we just
need to get maintainers to fill in the profiles...
- A reworking of the parallel build setup to work better with a
variety of systems (and to not take over huge systems entirely in
particular).
- The MAINTAINERS file is now converted to RST during the build.
Hopefully nobody ever tries to print this thing, or they will need
to load a lot of paper.
- A script and documentation making it easy for maintainers to add
Link: tags at commit time.
Also included is the removal of a bunch of spurious CR characters"
* tag 'docs-5.5a' of git://git.lwn.net/linux: (91 commits)
docs: remove a bunch of stray CRs
docs: fix up the maintainer profile document
libnvdimm, MAINTAINERS: Maintainer Entry Profile
Maintainer Handbook: Maintainer Entry Profile
MAINTAINERS: Reclaim the P: tag for Maintainer Entry Profile
docs, parallelism: Rearrange how jobserver reservations are made
docs, parallelism: Do not leak blocking mode to other readers
docs, parallelism: Fix failure path and add comment
Documentation: Remove bootmem_debug from kernel-parameters.txt
Documentation: security: core.rst: fix warnings
Documentation/process/howto/kokr: Update for 4.x -> 5.x versioning
Documentation/translation: Use Korean for Korean translation title
docs/memory-barriers.txt: Remove remaining references to mmiowb()
docs/memory-barriers.txt/kokr: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt/kokr: Fix style, spacing and grammar in I/O section
Documentation/kokr: Kill all references to mmiowb()
docs/memory-barriers.txt/kokr: Rewrite "KERNEL I/O BARRIER EFFECTS" section
docs: Add initial documentation for devfreq
Documentation: Document how to get links with git am
docs: Add request_irq() documentation
...
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- New bootctl driver for Mellanox BlueField SoC.
- New driver to support System76 laptops.
- Temperature monitoring and fan control on Acer Aspire 7551 is now
supported.
- Previously the Huawei driver handled only hotkeys. After the
conversion to WMI it has been expanded to support newer laptop
models.
- Big refactoring of intel-speed-select tools allows to use it on Intel
CascadeLake-N systems.
- Touchscreen support for ezpad 6 m4 and Schneider SCT101CTM tablets
- Miscellaneous clean ups and fixes here and there.
* tag 'platform-drivers-x86-v5.5-1' of git://git.infradead.org/linux-platform-drivers-x86: (59 commits)
platform/x86: hp-wmi: Fix ACPI errors caused by passing 0 as input size
platform/x86: hp-wmi: Fix ACPI errors caused by too small buffer
platform/x86: intel_pmc_core: Add Comet Lake (CML) platform support to intel_pmc_core driver
platform/x86: intel_pmc_core: Fix the SoC naming inconsistency
platform/mellanox: Fix Kconfig indentation
tools/power/x86/intel-speed-select: Display TRL buckets for just base config level
tools/power/x86/intel-speed-select: Ignore missing config level
platform/x86: touchscreen_dmi: Add info for the ezpad 6 m4 tablet
tools/power/x86/intel-speed-select: Increment version
tools/power/x86/intel-speed-select: Use core count for base-freq mask
tools/power/x86/intel-speed-select: Support platform with limited Intel(R) Speed Select
tools/power/x86/intel-speed-select: Use Frequency weight for CLOS
tools/power/x86/intel-speed-select: Make CLOS frequency in MHz
tools/power/x86/intel-speed-select: Use mailbox for CLOS_PM_QOS_CONFIG
tools/power/x86/intel-speed-select: Auto mode for CLX
tools/power/x86/intel-speed-select: Correct CLX-N frequency units
tools/power/x86/intel-speed-select: Change display of "avx" to "avx2"
tools/power/x86/intel-speed-select: Extend command set for perf-profile
Add touchscreen platform data for the Schneider SCT101CTM tablet
platform/x86: intel_int0002_vgpio: Pass irqchip when adding gpiochip
...
|
|
git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Allow to print symbolic error names via new %pe modifier.
- Use pr_warn() instead of the remaining pr_warning() calls. Fix
formatting of the related lines.
- Add VSPRINTF entry to MAINTAINERS.
* tag 'printk-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk: (32 commits)
checkpatch: don't warn about new vsprintf pointer extension '%pe'
MAINTAINERS: Add VSPRINTF
tools lib api: Renaming pr_warning to pr_warn
ASoC: samsung: Use pr_warn instead of pr_warning
lib: cpu_rmap: Use pr_warn instead of pr_warning
trace: Use pr_warn instead of pr_warning
dma-debug: Use pr_warn instead of pr_warning
vgacon: Use pr_warn instead of pr_warning
fs: afs: Use pr_warn instead of pr_warning
sh/intc: Use pr_warn instead of pr_warning
scsi: Use pr_warn instead of pr_warning
platform/x86: intel_oaktrail: Use pr_warn instead of pr_warning
platform/x86: asus-laptop: Use pr_warn instead of pr_warning
platform/x86: eeepc-laptop: Use pr_warn instead of pr_warning
oprofile: Use pr_warn instead of pr_warning
of: Use pr_warn instead of pr_warning
macintosh: Use pr_warn instead of pr_warning
idsn: Use pr_warn instead of pr_warning
ide: Use pr_warn instead of pr_warning
crypto: n2: Use pr_warn instead of pr_warning
...
|
|
The AML code implementing the WMI methods creates a variable length
field to hold the input data we pass like this:
CreateDWordField (Arg1, 0x0C, DSZI)
Local5 = DSZI /* \HWMC.DSZI */
CreateField (Arg1, 0x80, (Local5 * 0x08), DAIN)
If we pass 0 as bios_args.datasize argument then (Local5 * 0x08)
is 0 which results in these errors:
[ 71.973305] ACPI BIOS Error (bug): Attempt to CreateField of length zero (20190816/dsopcode-133)
[ 71.973332] ACPI Error: Aborting method \HWMC due to previous error (AE_AML_OPERAND_VALUE) (20190816/psparse-529)
[ 71.973413] ACPI Error: Aborting method \_SB.WMID.WMAA due to previous error (AE_AML_OPERAND_VALUE) (20190816/psparse-529)
And in our HPWMI_WIRELESS2_QUERY calls always failing. for read commands
like HPWMI_WIRELESS2_QUERY the DSZI value is not used / checked, except for
read commands where extra input is needed to specify exactly what to read.
So for HPWMI_WIRELESS2_QUERY we can safely pass the size of the expected
output as insize to hp_wmi_perform_query(), as we are already doing for all
other HPWMI_READ commands we send. Doing so fixes these errors.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=197007
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201981
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1520703
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The HP WMI calls may take up to 128 bytes of data as input, and
the AML methods implementing the WMI calls, declare a couple of fields for
accessing input in different sizes, specifycally the HWMC method contains:
CreateField (Arg1, 0x80, 0x0400, D128)
Even though we do not use any of the WMI command-types which need a buffer
of this size, the APCI interpreter still tries to create it as it is
declared in generoc code at the top of the HWMC method which runs before
the code looks at which command-type is requested.
This results in many of these errors on many different HP laptop models:
[ 14.459261] ACPI Error: Field [D128] at 1152 exceeds Buffer [NULL] size 160 (bits) (20170303/dsopcode-236)
[ 14.459268] ACPI Error: Method parse/execution failed [\HWMC] (Node ffff8edcc61507f8), AE_AML_BUFFER_LIMIT (20170303/psparse-543)
[ 14.459279] ACPI Error: Method parse/execution failed [\_SB.WMID.WMAA] (Node ffff8edcc61523c0), AE_AML_BUFFER_LIMIT (20170303/psparse-543)
This commit increases the size of the data element of the bios_args struct
to 128 bytes fixing these errors.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=197007
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201981
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1520703
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
intel_pmc_core driver
Add Comet Lake to the list of the platforms that intel_pmc_core driver
supports for pmc_core device.
Just like Ice Lake, Comet Lake can also reuse all the Cannon Lake PCH
IPs. No additional effort is needed to enable but to simply reuse them.
Cc: Mario Limonciello <mario.limonciello@dell.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: David E. Box <david.e.box@intel.com>
Cc: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Intel's SoCs follow a naming convention which spells out the SoC name as
two words instead of one word (E.g: Cannon Lake vs Cannonlake). Thus fix
the naming inconsistency across the intel_pmc_core driver, so future
SoCs can follow the naming consistency as below.
Cometlake -> Comet Lake
Tigerlake -> Tiger Lake
Elkhartlake -> Elkhart Lake
Cc: Mario Limonciello <mario.limonciello@dell.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: David E. Box <david.e.box@intel.com>
Cc: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add touchscreen info for the Jumper EZpad 6 m4 tablet.
Reported-and-tested-by: youling257 <youling257@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
I need to pick up the independent changes made to
Documentation/core-api/memory-allocation.rst to be able to merge further
work without creating a total mess.
|
