summaryrefslogtreecommitdiff
path: root/drivers/phy/ti
AgeCommit message (Collapse)AuthorFilesLines
2020-01-18phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESSHongbo Yao1-0/+1
If CONFIG_OF_ADDRESS is not set and COMPILE_TEST=y, the following error is seen while building phy-j721e-wiz.c drivers/phy/ti/phy-j721e-wiz.o: In function `wiz_remove': phy-j721e-wiz.c:(.text+0x1a): undefined reference to `of_platform_device_destroy' Fix the config dependency for PHY_J721E_WIZ here. Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 091876cc355d ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC") Signed-off-by: Hongbo Yao <yaohongbo@huawei.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Link: https://lore.kernel.org/r/20200117212310.2864-1-kishon@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-17phy: ti: j721e-wiz: Fix return value check in wiz_probe()Wei Yongjun1-1/+1
In case of error, the function devm_ioremap() returns NULL pointer not ERR_PTR(). The IS_ERR() test in the return value check should be replaced with NULL test. Fixes: 091876cc355d ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-14phy: ti: j721e-wiz: Manage typec-gpio-dirRoger Quadros1-0/+61
Based on this GPIO state we need to configure LN10 bit to swap lane0 and lane1 if required (flipped connector). Type-C companions typically need some time after the cable is plugged before and before they reflect the correct status of Type-C plug orientation on the DIR line. Type-C Spec specifies CC attachment debounce time (tCCDebounce) of 100 ms (min) to 200 ms (max). Use the DT property to figure out if we need to add delay or not before sampling the Type-C DIR line. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Jyri Sarha <jsarha@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-14phy: Enable compile testing for some of driversKrzysztof Kozlowski1-2/+2
Some of the phy drivers can be compile tested to increase build coverage. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2020-01-14phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoCKishon Vijay Abraham I3-0/+914
Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES wrapper used to configure some of the input signals to the SERDES. It is used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures three clock selects (pll0, pll1, dig), two divider clocks and supports resets for each of the lanes. [jsarha@ti.com: Add support for Torrent(10G) SERDES wrapper] Signed-off-by: Jyri Sarha <jsarha@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-12-20phy: ti-pipe3: make clk operations symmetric in probe and removeChuhong Yuan1-11/+7
The driver calls clk_prepare_enable in probe but the corresponding clk_disable_unprepare() is in ti_pipe3_disable_clocks(). Move clk_disable_unprepare() to remove to make them symmetric. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-11-27Merge tag 'char-misc-5.5-rc1' of ↵Linus Torvalds2-4/+1
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the big set of char/misc and other driver patches for 5.5-rc1 Loads of different things in here, this feels like the catch-all of driver subsystems these days. Full details are in the shortlog, but nothing major overall, just lots of driver updates and additions. All of these have been in linux-next for a while with no reported issues" * tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits) char: Fix Kconfig indentation, continued habanalabs: add more protection of device during reset habanalabs: flush EQ workers in hard reset habanalabs: make the reset code more consistent habanalabs: expose reset counters via existing INFO IOCTL habanalabs: make code more concise habanalabs: use defines for F/W files habanalabs: remove prints on successful device initialization habanalabs: remove unnecessary checks habanalabs: invalidate MMU cache only once habanalabs: skip VA block list update in reset flow habanalabs: optimize MMU unmap habanalabs: prevent read/write from/to the device during hard reset habanalabs: split MMU properties to PCI/DRAM habanalabs: re-factor MMU masks and documentation habanalabs: type specific MMU cache invalidation habanalabs: re-factor memory module code habanalabs: export uapi defines to user-space habanalabs: don't print error when queues are full habanalabs: increase max jobs number to 512 ...
2019-11-20phy: ti: phy-gmii-sel: dependency from ti cpsw-switchdev driverGrygorii Strashko1-2/+2
Add dependency from TI_CPSW_SWITCHDEV. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-25phy: ti: gmii-sel: fix mac tx internal delay for rgmii-rxidGrygorii Strashko1-1/+1
Now phy-gmii-sel will disable MAC TX internal delay for PHY interface mode "rgmii-rxid" which is incorrect. Hence, fix it by enabling MAC TX internal delay in the case of "rgmii-rxid" mode. Fixes: 92b58b34741f ("phy: ti: introduce phy-gmii-sel driver") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-10-25phy: ti: dm816x: remove set but not used variable 'phy_data'YueHaibing1-3/+0
Fixes gcc '-Wunused-but-set-variable' warning: drivers/phy/ti/phy-dm816x-usb.c:192:29: warning: variable phy_data set but not used [-Wunused-but-set-variable] It is never used, so can be removed. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-09-21Merge tag 'clk-for-linus' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux Pull clk updates from Stephen Boyd: "We have a small collection of core framework updates this time, mostly around clk registration by clk providers and debugfs "nice to haves" for rate constraints. I'll highlight that we're now setting the clk_init_data pointer inside struct clk_hw to NULL during clk_register(), which may break some drivers that thought they could use that pointer during normal operations. That change has been sitting in next for a while now but maybe something is still broken. We'l see. Other than that the core framework changes aren't invasive and they're fixing bugs, simplifying, and making things better. On the clk driver side we got the usual addition of new SoC support, new features for existing drivers, and bug fixes scattered throughout. The biggest diffstat is the Amlogic driver that gained CPU clk support in addition to migrating to the new way of specifying clk parents. After that the Qualcomm, i.MX, Mediatek, and Rockchip clk drivers got support for various new SoCs and clock controllers from those vendors. Core: - Drop NULL checks in clk debugfs - Add min/max rates to clk debugfs - Set clk_init_data pointer inside clk_hw to NULL after registration - Make clk_bulk_get_all() return an 'id' corresponding to clock-names - Evict parents from parent cache when they're unregistered New Drivers: - Add clock driver for i.MX8MN SoCs - Support aspeed AST2600 SoCs - Support for Mediatek MT6779 SoCs - Support qcom SM8150 GCC and RPMh clks - Support qcom QCS404 WCSS clks - Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807) - Addition of clock driver for Rockchip rk3308 SoCs Updates: - Add regulator support to the cdce925 clk driver - Add support for Raspberry Pi 4 bcm2711 SoCs - Add SDIO gate support to aspeed driver - Add missing of_node_put() calls in various clk drivers - Migrate Amlogic driver to new clock parent description method - Add DVFS support to Amlogic Meson g12 - Add Amlogic Meson g12a reset support to the axg audio clock controller - Add sm1 support to the Amlogic Meson g12a clock controller - Switch i.MX8MM clock driver to platform driver - Add Hifi4 DSP related clocks for i.MX8QXP SoC - Fix Audio PLL setting and parent clock for USB - Misc i.MX8 clock driver improvements and corrections - Set floor ops for Qualcomm SD clks so that rounding works - Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1 - Enable the Allwinner V3 SoC and fix the i2s clock for H6" * tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits) clk: Drop !clk checks in debugfs dumping clk: imx: imx8mn: fix pll mux bit clk: imx: imx8mm: fix pll mux bit clk: imx: clk-pll14xx: unbypass PLL by default clk: imx: pll14xx: avoid glitch when set rate clk: mvebu: ap80x: add AP807 clock support clk: mvebu: ap806: Prepare the introduction of AP807 clock support clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver clk: mvebu: ap806: be more explicit on what SaR is clk: mvebu: ap80x-cpu: add AP807 CPU clock support clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock dt-bindings: ap806: Document AP807 clock compatible dt-bindings: ap80x: Document AP807 CPU clock compatible clk: sprd: add missing kfree clk: at91: allow 24 Mhz clock as input for PLL clk: Make clk_bulk_get_all() return a valid "id" clk: actions: Fix factor clk struct member access clk: qcom: rcg: Return failure for RCG update clk: remove extra ---help--- tags in Kconfig clk: add include guard to clk-conf.h ...
2019-08-26phy: ti: am654-serdes: fix an use-after-free in serdes_am654_clk_register()Wen Yang1-11/+22
The regmap_node variable is still being used in the syscon_node_to_regmap() call after the of_node_put() call, which may result in use-after-free. Fixes: 71e2f5c5c224 ("phy: ti: Add a new SERDES driver for TI's AM654x SoC") Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Roger Quadros <rogerq@ti.com> Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-08-16phy: ti: am654-serdes: Don't reference clk_init_data after registrationStephen Boyd1-2/+2
A future patch is going to change semantics of clk_register() so that clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid referencing this member here so that we don't run into NULL pointer exceptions. Cc: Roger Quadros <rogerq@ti.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Link: https://lkml.kernel.org/r/20190731193517.237136-9-sboyd@kernel.org Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-07-01Merge tag 'phy-for-5.3' of ↵Greg Kroah-Hartman1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next phy: for 5.3 *) Add a new PHY driver for Qualcomm PCIe2 PHY *) Add a new PHY driver for Mixel DPHY present in i.MX8 *) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that PHY enable failed *) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to calling a sleeping function from invalid context *) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to imbalance powered flag *) Fix .cocci and sparse warnings Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> * tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: phy: qcom-qmp: Raise qcom_qmp_phy_enable() polling delay phy: meson-g12a-usb3-pcie: disable locking for cr_regmap phy: Add driver for mixel mipi dphy found on NXP's i.MX8 SoCs dt-bindings: phy: Add documentation for mixel dphy dt-bindings: phy-pxa-usb: add bindings phy: renesas: rcar-gen3-usb2: fix imbalance powered flag phy: qcom-qmp: Drop useless msm8998_pciephy_cfg setting phy: qcom-qmp: Correct READY_STATUS poll break condition phy: ti: am654-serdes: Make serdes_am654_xlate() static phy: usb: phy-brcm-usb: Fix platform_no_drv_owner.cocci warnings phy: samsung: Use struct_size() in devm_kzalloc() phy: qcom: Add Qualcomm PCIe2 PHY driver dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
2019-06-21phy: ti: am654-serdes: Make serdes_am654_xlate() staticYueHaibing1-2/+2
Fix sparse warning: drivers/phy/ti/phy-am654-serdes.c:250:12: warning: symbol 'serdes_am654_xlate' was not declared. Should it be static? Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-06-19treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner1-4/+1
Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 285Thomas Gleixner1-9/+1
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation version 2 of the license this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 100 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Alexios Zavras <alexios.zavras@intel.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157Thomas Gleixner3-33/+3
Based on 3 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version [author] [kishon] [vijay] [abraham] [i] [kishon]@[ti] [com] this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version [author] [graeme] [gregory] [gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i] [kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema] [hk] [hemahk]@[ti] [com] this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 1105 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Richard Fontana <rfontana@redhat.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-24treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 61Thomas Gleixner1-14/+1
Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation inc 675 mass ave cambridge ma 02139 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 441 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc) Reviewed-by: Richard Fontana <rfontana@redhat.com> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner1-0/+1
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-08Merge tag 'usb-5.2-rc1' of ↵Linus Torvalds4-97/+936
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB/PHY updates from Greg KH: "Here is the big set of USB and PHY driver patches for 5.2-rc1 There is the usual set of: - USB gadget updates - PHY driver updates and additions - USB serial driver updates and fixes - typec updates and new chips supported - mtu3 driver updates - xhci driver updates - other tiny driver updates Nothing really interesting, just constant forward progress. All of these have been in linux-next for a while with no reported issues. The usb-gadget and usb-serial trees were merged a bit "late", but both of them had been in linux-next before they got merged here last Friday" * tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (206 commits) USB: serial: f81232: implement break control USB: serial: f81232: add high baud rate support USB: serial: f81232: clear overrun flag USB: serial: f81232: fix interrupt worker not stop usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA usb: dwc3: Fix default lpm_nyet_threshold value usb: dwc3: debug: Print GET_STATUS(device) tracepoint usb: dwc3: Do core validation early on probe usb: dwc3: gadget: Set lpm_capable usb: gadget: atmel: tie wake lock to running clock usb: gadget: atmel: support USB suspend usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask dwc2: gadget: Fix completed transfer size calculation in DDMA usb: dwc2: Set lpm mode parameters depend on HW configuration usb: dwc2: Fix channel disable flow usb: dwc2: Set actual frame number for completed ISOC transfer usb: gadget: do not use __constant_cpu_to_le16 usb: dwc2: gadget: Increase descriptors count for ISOC's usb: introduce usb_ep_type_string() function usb: dwc3: move synchronize_irq() out of the spinlock protected block ...
2019-04-17phy: ti: am654-serdes: Support all clksel valuesRoger Quadros1-49/+83
Add support to select all 16 CLKSEL combinations that are shown in "SerDes Reference Clock Distribution" in AM65 TRM. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-04-17phy: ti: Add a new SERDES driver for TI's AM654x SoCKishon Vijay Abraham I3-0/+637
Add a new SERDES driver for TI's AM654x SoC which configures the SERDES only for PCIe. Support fo USB3 will be added later. SERDES in am654x has three input clocks (left input, externel reference clock and right input) and two output clocks (left output and right output) in addition to a PLL mux clock which the SERDES uses for Clock Multiplier Unit (CMU refclock). The PLL mux clock can select from one of the three input clocks. The right output can select between left input and external reference clock while the left output can select between the right input and external reference clock. The driver has support to select PLL mux and left/right output mux as specified in device tree. [rogerq@ti.com: Fix boot lockup caused by accessing a structure member (hw->init) allocated in stack of probe() and accessed in get_parent] [rogerq@ti.com: Fix "Failed to find the parent" warnings] Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-04-17phy: ti-pipe3: Fix PCIe power up sequenceRoger Quadros1-6/+6
TRM [1] mentions that we need to power up PCIESS_PHY_TX and PCIESS_PHY_RX before configuring PCIe_PHY_RX SCP settings. See "Table 26-81. PCIePHY Subsystem Low-Level Programming Sequence". [1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-04-17phy: ti-pipe3: Fix SATA & USB PHY power up sequenceRoger Quadros1-14/+30
As per "Table 26-7. SATA PHY Subsystem Low-Level Programming Sequence" in TRM [1] we need to turn on SATA_PHY_TX before SATA_PHY_RX. [1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-04-17phy: ti-pipe3: improve DPLL stability for SATA & USBRoger Quadros1-42/+173
For increased DPLL stability use the settings recommended in the TRM [1] for PHY_RX registers for SATA and USB. For SATA we need to use spread spectrum settings even though we don't have spread spectrum enabled. The suggested non-spread spectrum settings don't work. [1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-04-17phy: ti-pipe3: Introduce mode property in driver dataRoger Quadros1-36/+57
Introduce a mode property in the driver data so that we don't have to keep using "of_device_is_compatible()" throughtout the driver. No functional change. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-04-17phy: ti-pipe3: fix missing bit-wise or operator when assigning valColin Ian King1-1/+1
There seems to be a missing bit-wise or operator when setting val, fix this by adding it in. Fixes: 2796ceb0c18a ("phy: ti-pipe3: Update pcie phy settings") Cc: stable@vger.kernel.org # v4.19+ Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-04-17phy: ti: usb2: fix OMAP_CONTROL_PHY dependencyArnd Bergmann1-1/+1
With randconfig build testing on arm64, we can run into a configuration that has CONFIG_OMAP_CONTROL_PHY=m and CONFIG_OMAP_USB2=y, which in turn causes a link failure: drivers/phy/ti/phy-omap-usb2.o: In function `omap_usb_phy_power': phy-omap-usb2.c:(.text+0x17c): undefined reference to `omap_control_phy_power' I could not come up with a good way to correctly describe the relation of the two symbols, but if we just select CONFIG_OMAP_CONTROL_PHY during compile testing, we can no longer run into the broken configuration. Fixes: 6777cee3a872 ("phy: ti: usb2: Add support for AM654 USB2 PHY") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-04-17phy: phy-twl4030-usb: Fix cable state handlingTony Lindgren1-22/+13
With the recent regulator changes I noticed new warnings on doing rmmod of phy-twl4030-usb: WARNING: CPU: 0 PID: 1080 at drivers/regulator/core.c:2046 _regulator_put ... Turns out we can currently miss disconnect at least for cases where status is 0 and linkstat is 0. And in that case doing rmmod phy-twl4030-usb will produce the regulator_put() warning. This is because the missed disconnect causes unbalanced PM runtime calls and the regulators will be on exit. Let's fix the issue by using an atomic flag for the cable state to make sure that PM runtime won't get out of sync with the cable state. That way we can also simplify the code a bit. Note that we can also drop the old comments, those relate to issues that the battery charger driver and musb driver is dealing with rather than the USB PHY driver. Cc: NeilBrown <neilb@suse.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-02-12Merge tag 'phy-for-5.1' of ↵Greg Kroah-Hartman2-45/+66
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next Kishon writes: phy: for 5.1 *) Add a new driver to support Armada 3700 COMPHY IP (supports SATA, USB3, PCIe) *) Add a new driver to support Armada UTMI PHY *) Add a new driver to support Cadence D-PHY *) Extend omap-usb2 PHY driver to be used for AM654 USB2 PHY *) Extend qcom-qmp PHY driver to be used for UFS PHY and USB3 PHY in Qualcomm MSM8998 *) Extend qcom-qusb2 PHY driver to support QUSB2 PHY in Qualcomm MSM8998 *) Remove module specific code that is present for drivers that can be only built-in *) Allow Freescale IMX8MQ USB to be used for multiple SoCs and not just i.MX8MQ *) Cleanups such as switch to SPDX identifier, use readl_poll_timeout macro, remove unused headers etc., Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> * tag 'phy-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (32 commits) phy: qcom-qmp: Add QMP UFS PHY support for msm8998 dt-bindings: phy-qcom-qmp: Add qcom,msm8998-qmp-ufs-phy phy: bcm-sr-pcie: Change operation when PIPEMUX=1 phy: Add Cadence D-PHY support dt-bindings: phy: Move the Cadence D-PHY bindings phy: dphy: Clarify lanes parameter documentation phy: dphy: Change units of wakeup and init parameters phy: dphy: Remove unused header MAINTAINERS: phy: fill Armada 3700 PHY drivers entry dt-bindings: phy: mvebu-utmi: add UTMI PHY bindings phy: add A3700 UTMI PHY driver MAINTAINERS: phy: add entry for Armada 3700 COMPHY driver dt-bindings: phy: mvebu-comphy: extend the file to describe a3700 bindings phy: add A3700 COMPHY support phy: mvebu-cp110-comphy: fix port check in ->xlate() phy: armada375-usb2: switch to SPDX license identifier phy: make phy-armada375-usb2 explicitly non-modular phy: make phy-mvebu-sata explicitly non-modular phy: make phy-core explicitly non-modular phy: qcom-qusb2: Add QUSB2 PHY support for msm8998 ...
2019-02-07phy: ti: usb2: Add support for AM654 USB2 PHYRoger Quadros2-2/+19
Add support for the USB2 PHY on the AM654 SoC. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-02-07phy: ti: Don't depend on OMAP_OCP2SCPRoger Quadros1-2/+0
TI_PIPE3 and OMAP_USB2 don't depend on OMAP_OCP2SCP for build. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-02-07phy: ti: usb2: Fix logic on -EPROBE_DEFERRoger Quadros1-41/+47
If clk_get() returns -EPROBE_DEFER then we should just return instead of falling back to old clock name. Use clk_prepare_enable() and clk_disable_unprepare() instead of splitting up prepare/unprepare from enable/disable. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-01-26Merge tag 'usb-5.0-rc4' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB/PHY fixes from Greg KH: "Here are a number of small USB and PHY driver fixes for 5.0-rc4. Nothing major at all, just the usual selection of USB gadget bugfixes, some new USB serial driver ids, some SPDX fixes, and some PHY driver fixes for reported issues. All of these have been in linux-next for a while with no reported issues" * tag 'usb-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: USB: serial: keyspan_usa: add proper SPDX lines for .h files USB: EHCI: ehci-mv: add MODULE_DEVICE_TABLE USB: leds: fix regression in usbport led trigger usb: chipidea: fix static checker warning for NULL pointer MAINTAINERS: email address update in MAINTAINERS entries USB: usbip: delete README file USB: serial: pl2303: add new PID to support PL2303TB usb: dwc2: gadget: Fix Remote Wakeup interrupt bit clearing phy: ath79-usb: Fix the main reset name to match the DT binding phy: ath79-usb: Fix the power on error path phy: fix build breakage: add PHY_MODE_SATA phy: ti: ensure priv is not null before dereferencing it USB: serial: ftdi_sio: fix GPIO not working in autosuspend usb: gadget: Potential NULL dereference on allocation error usb: dwc3: gadget: Fix the uninitialized link_state when udc starts usb: dwc3: gadget: Clear req->needs_extra_trb flag on cleanup usb: dwc3: gadget: synchronize_irq dwc irq in suspend USB: serial: simple: add Motorola Tetra TPG2200 device id
2019-01-16phy: ti: ensure priv is not null before dereferencing itColin Ian King1-2/+2
Currently priv is being dereferenced before priv is being null checked. Fix this by moving the null check on priv before the dereference. Detected by CoverityScan, CID#1476018 ("Dereference before null check") Fixes: 92b58b34741f ("phy: ti: introduce phy-gmii-sel driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2019-01-07phy: ti: Fix compilation failures without REGMAPJason Gunthorpe1-0/+1
This driver requires regmap or the compile fails: drivers/phy/ti/phy-gmii-sel.c:43:27: error: array type has incomplete element type ‘struct reg_field’ const struct reg_field (*regfields)[PHY_GMII_SEL_LAST]; Add it to kconfig. Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-12phy: ti: fix semicolon.cocci warningskbuild test robot1-1/+1
drivers/phy/ti/phy-gmii-sel.c:91:2-3: Unneeded semicolon Remove unneeded semicolon. Generated by: scripts/coccinelle/misc/semicolon.cocci Fixes: 1811851f4e73 ("phy: ti: introduce phy-gmii-sel driver") CC: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-12-12phy: ti: introduce phy-gmii-sel driverGrygorii Strashko3-0/+360
TI am335x/am437x/dra7(am5)/dm814x CPSW3G Ethernet Subsystem supports two 10/100/1000 Ethernet ports with selectable G/MII, RMII, and RGMII interfaces. The interface mode is selected by configuring the MII mode selection register(s) (GMII_SEL) in the System Control Module chapter (SCM). GMII_SEL register(s) and bit fields placement in SCM are different between SoCs while fields meaning is the same. Historically CPSW external Port's interface mode selection configuration was introduced using custom API and driver cpsw-phy-sel.c. This leads to unnecessary driver, DT binding and custom API support effort. This patch introduces CPSW Port's PHY Interface Mode selection Driver (phy-gmii-sel) which implements standard Linux PHY interface and used as a replacement for TI's specific driver cpsw-phy-sel.c and corresponding custom API. Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-12-12phy: core: rework phy_set_mode to accept phy mode and submodeGrygorii Strashko2-2/+3
Currently the attempt to add support for Ethernet interface mode PHY (MII/GMII/RGMII) will lead to the necessity of extending enum phy_mode and duplicate there values from phy_interface_t enum (or introduce more PHY callbacks) [1]. Both approaches are ineffective and would lead to fast bloating of enum phy_mode or struct phy_ops in the process of adding more PHYs for different subsystems which will make them unmaintainable. As discussed in [1] the solution could be to introduce dual level PHYs mode configuration - PHY mode and PHY submode. The PHY mode will define generic PHY type (subsystem - PCIE/ETHERNET/USB_) while the PHY submode - subsystem specific interface mode. The last is usually already defined in corresponding subsystem headers (phy_interface_t for Ethernet, enum usb_device_speed for USB). This patch is cumulative change which refactors PHY framework code to support dual level PHYs mode configuration - PHY mode and PHY submode. It extends .set_mode() callback to support additional parameter "int submode" and converts all corresponding PHY drivers to support new .set_mode() callback declaration. The new extended PHY API int phy_set_mode_ext(struct phy *phy, enum phy_mode mode, int submode) is introduced to support dual level PHYs mode configuration and existing phy_set_mode() API is converted to macros, so PHY framework consumers do not need to be changed (~21 matches). [1] http://lkml.kernel.org/r/d63588f6-9ab0-848a-5ad4-8073143bd95d@ti.com Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-09-25phy: phy-twl4030-usb: fix denied runtime accessAndreas Kemnade1-0/+29
When runtime is not enabled, pm_runtime_get_sync() returns -EACCESS, the counter will be incremented but the resume callback not called, so enumeration and charging will not start properly. To avoid that happen, disable irq on suspend and recheck on resume. Practically this happens when the device is woken up from suspend by plugging in usb. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-02-19ARM: da8xx: use platform data for CFGCHIP syscon regmapDavid Lechner1-3/+5
This converts from using a platform device for the CFGCHIP syscon regmap to using platform data to pass the regmap to consumers. A lazy getter function is used so that the regmap will only be created if it is actually used. This function will also be used in the clock init when we convert to the common clock framework. The USB PHY driver is currently the only consumer. This driver is updated to use platform data to get the CFGCHIP regmap instead of syscon_regmap_lookup_by_pdevname(). Signed-off-by: David Lechner <david@lechnology.com> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2018-02-12phy: da8xx-usb: rename clock con_idsDavid Lechner1-4/+4
This renames the clock con_ids in the DA8XX USB PHY driver as well as the matching names in the mach clock registration code. This is in preparation for using device tree clocks where these names will become part of the device tree bindings. The new names more closely match the names used in the USB clock diagram in the SoC TRM. Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: David Lechner <david@lechnology.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2017-11-14Merge tag 'usb-4.15-rc1' of ↵Linus Torvalds1-1/+100
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB/PHY updates from Greg KH: "Here is the big set of USB and PHY driver updates for 4.15-rc1. There is the usual amount of gadget and xhci driver updates, along with phy and chipidea enhancements. There's also a lot of SPDX tags and license boilerplate cleanups as well, which provide some churn in the diffstat. Other major thing is the typec code that moved out of staging and into the "real" part of the drivers/usb/ tree, which was nice to see happen. All of these have been in linux-next with no reported issues for a while" * tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits) usb: gadget: f_fs: Fix use-after-free in ffs_free_inst USB: usbfs: compute urb->actual_length for isochronous usb: core: message: remember to reset 'ret' to 0 when necessary USB: typec: Remove remaining redundant license text USB: typec: add SPDX identifiers to some files USB: renesas_usbhs: rcar?.h: add SPDX tags USB: chipidea: ci_hdrc_tegra.c: add SPDX line USB: host: xhci-debugfs: add SPDX lines USB: add SPDX identifiers to all remaining Makefiles usb: host: isp1362-hcd: remove a couple of redundant assignments USB: adutux: remove redundant variable minor usb: core: add a new usb_get_ptm_status() helper usb: core: add a 'type' parameter to usb_get_status() usb: core: introduce a new usb_get_std_status() helper usb: core: rename usb_get_status() 'type' argument to 'recip' usb: core: add Status Type definitions USB: gadget: Remove redundant license text USB: gadget: function: Remove redundant license text USB: gadget: udc: Remove redundant license text USB: gadget: legacy: Remove redundant license text ...
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman1-0/+1
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-23phy: ti-pipe3: Update pcie phy settingsKishon Vijay Abraham I1-1/+100
Update the PCIe phy settings based on new settings available in AM572x Technical Reference Manual[1] Revision I, revised April 2017 in Table 26-62 "Preferred PCIe_PHY_RX SCP Register Settings". [1] http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf Cc: Vignesh R <vigneshr@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> [nsekhar@ti.com: commit message updates] Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2017-09-07Merge tag 'mfd-next-4.14' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd Pull MFD updates from Lee Jones: "New Drivers - RK805 Power Management IC (PMIC) - ROHM BD9571MWV-M MFD Power Management IC (PMIC) - Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs New Device Support: - Add support for HiSilicon Hi6421v530 to hi6421-pmic-core - Add support for X-Powers AXP806 to axp20x - Add support for X-Powers AXP813 to axp20x - Add support for Intel Sunrise Point LPSS to intel-lpss-pci New Functionality: - Amend API to provide register layout; atmel-smc Fix-ups: - DT re-work; omap, nokia - Header file location change {I2C => MFD}; dm355evm_msp, tps65010 - Fix chip ID formatting issue(s); rk808 - Optionally register touchscreen devices; da9052-core - Documentation improvements; twl-core - Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi - Drop unnecessary static declaration; max8925-i2c - Kconfig changes (missing deps and remove module support) - Slim down oversized licence statement; hi6421-pmic-core - Use managed resources (devm_*); lp87565 - Supply proper error checking/handling; t7l66xb Bug Fixes: - Fix counter duplication issue; da9052-core - Fix potential NULL deference issue; max8998 - Leave SPI-NOR write-protection bit alone; lpc_ich - Ensure device is put into reset during suspend; intel-lpss - Correct register offset variable size; omap-usb-tll" * tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits) mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT dt-bindings: mfd: Add bindings for ZII RAVE devices mfd: omap-usb-tll: Fix register offsets mfd: da9052: Constify spi_device_id mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend mfd: da9055: Constify i2c_device_id mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices mfd: t7l66xb: Handle return value of clk_prepare_enable mfd: Add ROHM BD9571MWV-M PMIC DT bindings mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool mfd: lp87565: Convert to use devm_mfd_add_devices() mfd: Add support for TPS68470 device mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell mfd: syscon: atmel-smc: Add helper to retrieve register layout mfd: axp20x: Use correct platform device ID for many PEK dt-bindings: mfd: axp20x: Introduce bindings for AXP813 mfd: axp20x: Add support for AXP813 PMIC dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips mfd: Add ROHM BD9571MWV-M MFD PMIC driver ...
2017-09-04mfd: twl: Move header file out of I2C realmWolfram Sang1-1/+1
include/linux/i2c is not for client devices. Move the header file to a more appropriate location. Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Acked-by: Jonathan Cameron <jic23@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-08-22phy: phy-twl4030-usb: silence an uninitialized variable warningDan Carpenter1-1/+1
The "check" variable isn't necessarily initialized when we print it out in the debugging messages. It's a pretty haphazard affair and it doesn't matter very much what we initialize "check" to. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2017-08-20phy: ti-pipe3: Use TRM recommended settings for SATA DPLLRoger Quadros1-5/+5
The AM572x Technical Reference Manual, SPRUHZ6H, Revised November 2016 [1], shows recommended settings for the SATA DPLL in Table 26-8. DPLL CLKDCOLDO Recommended Settings. Use those settings in the driver. The TRM does not show a value for 20MHz SYS_CLK so we use something close to the 26MHz setting. [1] - http://www.ti.com/lit/ug/spruhz6h/spruhz6h.pdf Signed-off-by: Roger Quadros <rogerq@ti.com> [nsekhar@ti.com: add exact TRM version to commit text] Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-16 12:00:20 +0300