| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
RZ/G2L has separate channel specific IRQs for transmit and error
interrupts. But the IRQ handler processes both channels, even if there
no interrupt occurred on one of the channels.
This patch fixes the issue by passing a channel specific context
parameter instead of global one for the IRQ register and the IRQ
handler, it just handles the channel which is triggered the interrupt.
Fixes: 76e9353a80e9 ("can: rcar_canfd: Add support for RZ/G2L family")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20221025155657.1426948-3-biju.das.jz@bp.renesas.com
Cc: stable@vger.kernel.org
[mkl: adjust commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
FIFO receive
We are seeing an IRQ storm on the global receive IRQ line under heavy
CAN bus load conditions with both CAN channels enabled.
Conditions:
The global receive IRQ line is shared between can0 and can1, either of
the channels can trigger interrupt while the other channel's IRQ line
is disabled (RFIE).
When global a receive IRQ interrupt occurs, we mask the interrupt in
the IRQ handler. Clearing and unmasking of the interrupt is happening
in rx_poll(). There is a race condition where rx_poll() unmasks the
interrupt, but the next IRQ handler does not mask the IRQ due to
NAPIF_STATE_MISSED flag (e.g.: can0 RX FIFO interrupt is disabled and
can1 is triggering RX interrupt, the delay in rx_poll() processing
results in setting NAPIF_STATE_MISSED flag) leading to an IRQ storm.
This patch fixes the issue by checking IRQ active and enabled before
handling the IRQ on a particular channel.
Fixes: dd3bd23eb438 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20221025155657.1426948-2-biju.das.jz@bp.renesas.com
Cc: stable@vger.kernel.org
[mkl: adjust commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
kvaser_usb uses completions to signal when a response event is received
for outgoing commands.
However, it uses init_completion() to reinitialize the start_comp and
stop_comp completions before sending the start/stop commands.
In case the device sends the corresponding response just before the
actual command is sent, complete() may be called concurrently with
init_completion() which is not safe.
This might be triggerable even with a properly functioning device by
stopping the interface (CMD_STOP_CHIP) just after it goes bus-off (which
also causes the driver to send CMD_STOP_CHIP when restart-ms is off),
but that was not tested.
Fix the issue by using reinit_completion() instead.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The phylib callback is called after MAC driver's own resume callback is
called. For AVE driver, after resuming immediately, PHY state machine is
in PHY_NOLINK because there is a time lag from link-down to link-up due to
autoneg. The result is WARN_ON() dump in mdio_bus_phy_resume().
Since ave_resume() itself calls phy_resume(), AVE driver should manage
PHY PM. To indicate that MAC driver manages PHY PM, set
phydev->mac_managed_pm to true to avoid the unnecessary phylib call and
add missing phy_init_hw() to ave_resume().
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221024072227.24769-1-hayashi.kunihiko@socionext.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ave_open() in ave_resume() executes __phy_resume() via phy_start(), so no
need to call phy_resume() explicitly. Remove it.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221024072314.24969-1-hayashi.kunihiko@socionext.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using 'ethtool -d […]' on an i.MX6UL leads to a kernel crash:
Unhandled fault: external abort on non-linefetch (0x1008) at […]
due to this SoC has less registers in its FEC implementation compared to other
i.MX6 variants. Thus, a run-time decision is required to avoid access to
non-existing registers.
Fixes: a51d3ab50702 ("net: fec: use a more proper compatible string for i.MX6UL type device")
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221024080552.21004-1-jbe@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-10-25
The 1st patch adds a missing cleanup call in the error path of the
probe function in mpc5xxx glue code for the mscan driver.
The 2nd patch adds a missing cleanup call in the error path of the
probe function of the mcp251x driver.
* tag 'linux-can-fixes-for-6.1-20221025' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251x: mcp251x_can_probe(): add missing unregister_candev() in error path
can: mscan: mpc5xxx: mpc5xxx_can_probe(): add missing put_clock() in error path
====================
Link: https://lore.kernel.org/r/20221026075520.1502520-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
state is deferenced earlier in the function, the NULL check
is pointless. Since we don't have any crash reports presumably
it's safe to assume state is not NULL.
Fixes: f392a1846489 ("net: phylink: provide phylink_validate_mask_caps() helper")
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20221025185126.1720553-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan-next
Stefan Schmidt says:
====================
==
One of the biggest cycles for ieee802154 in a long time. We are landing the
first pieces of a big enhancements in managing PAN's. We might have another pull
request ready for this cycle later on, but I want to get this one out first.
Miquel Raynal added support for sending frames synchronously as a dependency
to handle MLME commands. Also introducing more filtering levels to match with
the needs of a device when scanning or operating as a pan coordinator.
To support development and testing the hwsim driver for ieee802154 was also
enhanced for the new filtering levels and to update the PIB attributes.
Alexander Aring fixed quite a few bugs spotted during reviewing changes. He
also added support for TRAC in the atusb driver to have better failure
handling if the firmware provides the needed information.
Jilin Yuan fixed a comment with a repeated word in it.
==================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
this is a pull request of 29 patches for net-next/master.
The first patch is by Daniel S. Trevitz and adds documentation for
switchable termination resistors.
Zhang Changzhong's patch fixes a debug output in the j13939 stack.
Oliver Hartkopp finally removes the pch_can driver, which is
superseded by the generic c_can driver.
Gustavo A. R. Silva replaces a zero-length array with
DECLARE_FLEX_ARRAY() in the ucan driver.
Kees Cook's patch removes a no longer needed silencing of
"-Warray-bounds" warnings for the kvaser_usb driver.
The next 2 patches target the m_can driver. The first is by me cleans
up the LEC error handling, the second is by Vivek Yadav and extends
the LEC error handling to the data phase of CAN-FD frames.
The next 9 patches all target the gs_usb driver. The first 5 patches
are by me and improve the Kconfig prompt and help text, set
netdev->dev_id to distinguish multi CAN channel devices, allow
loopback and listen only at the same time, and clean up the
gs_can_open() function a bit. The remaining 4 patches are by Jeroen
Hofstee and add support for 2 new features: Bus Error Reporting and
Get State.
Jimmy Assarsson and Anssi Hannula contribute 10 patches for the
kvaser_usb driver. They first add Listen Only and Bus Error Reporting
support, handle CMD_ERROR_EVENT errors, improve CAN state handling,
restart events, and configuration of the bit timing parameters.
Another patch by me which fixes the indention in the m_can driver.
A patch by Dongliang Mu cleans up the ucan_disconnect() function in
the ucan driver.
The last patch by Biju Das is for the rcan_canfd driver and cleans up
the reset handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace devm_reset_control_get_exclusive->devm_reset_control_
get_optional_exclusive so that we can avoid unnecessary
SoC specific check in probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/20221025155657.1426948-4-biju.das.jz@bp.renesas.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
From API pairing, change unregister_netdev() to unregister_candev()
since the registration function is register_candev(). Actually, they
are the same.
Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/all/20221024110033.727542-1-dzm91@hust.edu.cn
[mkl: adjust subject + commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver uses indent-with-tab for defines. Replace spaces after
IR_ERR_BUS_31X with tab for consistent indention.
Link: https://lore.kernel.org/all/20221024185544.68240-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
parameters in do_set_{,data}_bittiming
The device will respond with a CMD_ERROR_EVENT command, with error_code
KVASER_USB_{LEAF,HYDRA}_ERROR_EVENT_PARAM, if the CMD_SET_BUSPARAMS_REQ
contains invalid bittiming parameters.
However, this command does not contain any channel reference.
To check if the CMD_SET_BUSPARAMS_REQ was successful, redback and compare
the requested bittiming parameters with the device reported parameters.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Co-developed-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-12-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add struct kvaser_usb_busparams containing the busparameters used in
CMD_{SET,GET}_BUSPARAMS* commands.
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-11-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When auto-restart is enabled, the kvaser_usb_leaf driver considers
transition from any state >= CAN_STATE_BUS_OFF as a bus-off recovery
event (restart).
However, these events may occur at interface startup time before
kvaser_usb_open() has set the state to CAN_STATE_ERROR_ACTIVE, causing
restarts counter to increase and CAN_ERR_RESTARTED to be sent despite no
actual restart having occurred.
Fix that by making the auto-restart condition checks more strict so that
they only trigger when the interface was actually in the BUS_OFF state.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-10-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
With 0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 it was observed
that if the device was bus-off when stopped, at next start (either via
interface down/up or manual bus-off restart) the initial
CMD_CHIP_STATE_EVENT received just after CMD_START_CHIP_REPLY will have
the M16C_STATE_BUS_OFF bit still set, causing the interface to
immediately go bus-off again.
The bit seems to internally clear quickly afterwards but we do not get
another CMD_CHIP_STATE_EVENT.
Fix the issue by ignoring any initial bus-off state until we see at
least one bus-on state. Also, poll the state periodically until that
occurs.
It is possible we lose one actual immediately occurring bus-off event
here in which case the HW will auto-recover and we see the recovery
event. We will then catch the next bus-off event, if any.
This issue did not reproduce with 0bfd:0017 Kvaser Memorator
Professional HS/HS FW 2.0.50.
Fixes: 71873a9b38d1 ("can: kvaser_usb: Add support for more Kvaser Leaf v2 devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-9-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 sends a
CMD_CHIP_STATE_EVENT indicating bus-off after stopping the device,
causing a stopped device to appear as CAN_STATE_BUS_OFF instead of
CAN_STATE_STOPPED.
Fix that by not handling error events on stopped devices.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-8-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The tested 0bfd:0017 Kvaser Memorator Professional HS/HS FW 2.0.50 and
0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 do not seem to send
any unsolicited events when error counters decrease or when the device
transitions from ERROR_PASSIVE to ERROR_ACTIVE (or WARNING).
This causes the interface to e.g. indefinitely stay in the ERROR_PASSIVE
state.
Fix that by asking for chip state (inc. counters) event every 0.5 secs
when error counters are non-zero.
Since there are non-error-counter devices, also always poll in
ERROR_PASSIVE even if the counters show zero.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-7-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
kvaser_usb_leaf_rx_error_update_can_state() sets error state according
to error counters when the hardware does not indicate a specific state
directly.
However, this is currently gated behind a check for
M16C_STATE_BUS_ERROR which does not always seem to be set when error
counters are increasing, and may not be set when error counters are
decreasing.
This causes the CAN_STATE_ERROR_WARNING state to not be set in some
cases even when appropriate.
Change the code to set error state from counters even without
M16C_STATE_BUS_ERROR.
The Error-Passive case seems superfluous as it is already set via
M16C_STATE_BUS_PASSIVE flag above, but it is kept for now.
Tested with 0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The device will send an error event command, to indicate certain errors.
This indicates a misbehaving driver, and should never occur.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Co-developed-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
{leaf,usbcan}_cmd_can_error_event
Prepare for handling CMD_ERROR_EVENT. Rename struct
{leaf,usbcan}_cmd_error_event to {leaf,usbcan}_cmd_can_error_event.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-4-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Use the CMD_GET_CAPABILITIES_REQ command to query the device for certain
capabilities. We are only interested in LISTENONLY mode and wither the
device reports CAN error counters.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
IPA v3.1 doesn't support the IDLE_INDICATION_CFG register, this was
causing a harmless splat in ipa_idle_indication_cfg(), add a version
check to prevent trying to fetch this register on v3.1
Fixes: 6a244b75cfab ("net: ipa: introduce ipa_reg()")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Tested-by: Jami Kettunen <jami.kettunen@somainline.org>
Link: https://lore.kernel.org/r/20221024234850.4049778-1-caleb.connolly@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The resource group limits for IPA v3.1 mistakenly used 6 bit wide mask
values, when the hardware actually uses 8. Out of range values were
silently ignored before, so the IPA worked as expected. However the
new generalised register definitions introduce stricter checking here,
they now cause some splats and result in the value 0 being written
instead. Fix the limit bitmask widths so that the correct values can be
written.
Fixes: 1c418c4a929c ("net: ipa: define resource group/type IPA register fields")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Tested-by: Jami Kettunen <jami.kettunen@somainline.org>
Link: https://lore.kernel.org/r/20221024210336.4014983-2-caleb.connolly@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some resource limits on IPA v3.5.1 have their max values set to
255, this causes a few splats in ipa_reg_encode and prevents the
IPA from booting properly. The limits are all 6 bits wide so
adjust the max values to 63.
Fixes: 1c418c4a929c ("net: ipa: define resource group/type IPA register fields")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20221024210336.4014983-1-caleb.connolly@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Variable tx_use is just being incremented and it's never used
anywhere else. The variable and the increment are redundant so
remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221024143501.2163720-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release()
while unbinding device.
Fixes: 8ca86fd83eae ("net: Micrel KSZ8841/2 PCI Ethernet driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221024131338.2848959-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Variable num_entries is just being incremented and it's never used
anywhere else. The variable and the increment are redundant so
remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221024125951.2155434-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set max_mtu/min_mtu directly to avoid making the validity judgment
when set mtu, because the judgment is made in net/core: dev_validate_mtu,
so to simplify the code.
Signed-off-by: caihuoqing <cai.huoqing@linux.dev>
Link: https://lore.kernel.org/r/20221024103349.4494-1-cai.huoqing@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix setting bits for specific flow_type for GLQF_HASH_INSET register.
In previous version all of the bits were set only in hena register, while
in inset only one bit was set. In order for this working correctly on all
types of cards these bits needs to be set correctly for both hena and inset
registers.
Fixes: eb0dd6e4a3b3 ("i40e: Allow RSS Hash set with less than four parameters")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a reset was triggered on one VF with i40e_reset_vf
global PF state __I40E_VF_DISABLE was set on a PF until
the reset finished. If immediately after triggering reset
on one VF there is a request to reset on another
it will cause a hang on VF side because VF will be notified
of incoming reset but the reset will never happen because
of this global state, we will get such error message:
[ +4.890195] iavf 0000:86:02.1: Never saw reset
and VF will hang waiting for the reset to be triggered.
Fix this by introducing new VF state I40E_VF_STATE_RESETTING
that will be set on a VF if it is currently resetting instead of
the global __I40E_VF_DISABLE PF state.
Fixes: 3ba9bcb4b68f ("i40e: add locking around VF reset")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When enabling flow type for RSS hash via ethtool:
ethtool -N $pf rx-flow-hash tcp4|tcp6|udp4|udp6 s|d
the driver would fail to setup this setting on X722
device since it was using the mask on the register
dedicated for X710 devices.
Apply a different mask on the register when setting the
RSS hash for the X722 device.
When displaying the flow types enabled via ethtool:
ethtool -n $pf rx-flow-hash tcp4|tcp6|udp4|udp6
the driver would print wrong values for X722 device.
Fix this issue by testing masks for X722 device in
i40e_get_rss_hash_opts function.
Fixes: eb0dd6e4a3b3 ("i40e: Allow RSS Hash set with less than four parameters")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for MDI-X status and configuration for KSZ9131 chips
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add pause get and set functions
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Round up allocations with kmalloc_size_roundup() so that build_skb()'s
use of ksize() is always accurate and no special handling of the memory
is needed by KASAN, UBSAN_BOUNDS, nor FORTIFY_SOURCE.
Cc: Rasesh Mody <rmody@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221022021004.gonna.489-kees@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Verify that the sizes of the routing and filter table memory regions
are valid as part of memory initialization, rather than waiting for
table initialization. The main reason to do this is that upcoming
patches use these memory region sizes to determine the number of
entries in these tables, and we'll want to know these sizes are good
sooner.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
What ipa_table_valid() (and ipa_table_valid_one(), which it calls)
does is ensure that the memory regions that hold routing and filter
tables have reasonable size. Specifically, it checks that the size
of a region is sufficient (or rather, exactly the right size) to
hold the maximum number of entries supported by the driver. (There
is an additional check that's erroneous, but in practice it is never
reached.)
Recently ipa_table_mem_valid() was added, which is called by
ipa_table_init(). That function verifies that all table memory
regions are of sufficient size, and requires hashed tables to have
zero size if hashing is not supported. It only ensures the filter
table is large enough to hold the number of endpoints that support
filtering, but that is adequate.
Therefore everything that ipa_table_valid() does is redundant, so
get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, ipa_cmd_data_valid() is called by ipa_mem_config().
Nothing it does requires access to hardware though, so it can be
done during the init phase of IPA driver startup.
Create a new function ipa_cmd_init(), whose purpose is to do early
initialization related to IPA immediate commands. It will call the
build-time validation function, then will make the two calls made
previously by ipa_cmd_data_valid(). This make ipa_cmd_data_valid()
unnecessary, so get rid of it.
Rename ipa_cmd_header_valid() to be ipa_cmd_header_init_local_valid(),
so its name is clearer about which IPA immediate command it is
associated with.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We currently verify the table size and offset fit in the immediate
command fields that must encode them in ipa_table_valid_one(). We
can now make this check earlier, in ipa_table_mem_valid().
The non-hashed IPv4 filter and route tables will always exist, and
their sizes will match the IPv6 tables, as well as the hashed tables
(if supported). So it's sufficient to verify the offset and size of
the IPv4 non-hashed tables fit into these fields.
Rename the function ipa_cmd_table_init_valid(), to reinforce that
it is the TABLE_INIT immediate command fields we're checking.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add checks in ipa_table_init() to ensure the memory regions defined
for IPA filter and routing tables are valid.
For routing tables, the checks ensure:
- The non-hashed IPv4 and IPv6 routing tables are defined
- The non-hashed IPv4 and IPv6 routing tables are the same size
- The number entries in the non-hashed IPv4 routing table is enough
to hold the number entries available to the modem, plus at least
one usable by the AP.
For filter tables, the checks ensure:
- The non-hashed IPv4 and IPv6 filter tables are defined
- The non-hashed IPv4 and IPv6 filter tables are the same size
- The number entries in the non-hashed IPv4 filter table is enough
to hold the endpoint bitmap, plus an entry for each defined
endpoint that supports filtering.
In addition, for both routing and filter tables:
- If hashing isn't supported (IPA v4.2), hashed tables are zero size
- If hashing *is* supported, all hashed tables are the same size as
their non-hashed counterparts.
When validating the size of routing tables, require the AP to have
at least one entry (in addition to those used by the modem).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There's no need to ensure table memory regions fit within the
IPA-local memory range. And there's no need to ensure the modem
header memory region is in range either. These are verified for all
memory regions in ipa_mem_size_valid(), once we have settled on the
size of IPA memory.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The entries in each IPA routing table are divided between the modem
and the AP. The modem always gets some number of entries located at
the base of the table; the AP gets all those that follow.
There's no reason to think the modem will use anything different
from the first entries in a routing table, so:
- Get rid of IPA_ROUTE_MODEM_MIN (just assume it's 0)
- Get rid of IPA_ROUTE_AP_MIN (just assume it's IPA_ROUTE_MODEM_COUNT)
And finally:
- Open-code IPA_ROUTE_AP_COUNT and remove its definition
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
RK3588(s) can have multiple gmac controllers.
Re-use rk3568 logic to distinguish them.
Fixes: 2f2b60a0ec28 ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20221021172422.88534-1-sebastian.reichel@collabora.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch uses TC skbedit queue_mapping action to support
forwarding packets to a device queue. Such filters with action
forward to queue will be the highest priority switch filter in
HW.
Example:
$ tc filter add dev ens4f0 protocol ip ingress flower\
dst_ip 192.168.1.12 ip_proto tcp dst_port 5001\
action skbedit queue_mapping 5 skip_sw
The above command adds an ingress filter, incoming packets
qualifying the match will be accepted into queue 5. The queue
number is in decimal format.
Refactored ice_add_tc_flower_adv_fltr() to consolidate code with
action FWD_TO_VSI and FWD_TO QUEUE.
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In mcp251x_can_probe(), if mcp251x_gpio_setup() fails, it forgets to
unregister the CAN device.
Fix this by unregistering can device in mcp251x_can_probe().
Fixes: 2d52dabbef60 ("can: mcp251x: add GPIO support")
Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/all/20221024090256.717236-1-dzm91@hust.edu.cn
[mkl: adjust label]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The commit 1149108e2fbf ("can: mscan: improve clock API use") only
adds put_clock() in mpc5xxx_can_remove() function, forgetting to add
put_clock() in the error handling code.
Fix this bug by adding put_clock() in the error handling code.
Fixes: 1149108e2fbf ("can: mscan: improve clock API use")
Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/all/20221024133828.35881-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Since we no longer mis-detect high-power mode with the DM7052 module,
we no longer need the hack in sfp_module_enable_high_power(), and can
now switch this to use sfp_modify_u8().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a helper to modify bits in a single byte in memory space, and use
it when updating the soft tx-disable flag in the module.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide a named definition for the power level select bit in the
extended status register, rather than using BIT(0) in the code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
