summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2021-04-15ice: refactor interrupt moderation writesJesse Brandeburg5-104/+112
Introduce several new helpers for writing ITR and GLINT_RATE registers, and refactor the code calling them. This resulted in removal of several duplicate functions and rolled a bunch of simple code back into the calling routines. In particular this removes some code that was doing both a store and a set in a helper function, which seems better done as separate tasks in the caller (and generally takes less lines of code even with a tiny bit of repetition). Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-04-15ice: Add new VSI states to track netdev alloc/registrationAnirudh Venkataramanan3-6/+22
Add two new VSI states, one to track if a netdev for the VSI has been allocated and the other to track if the netdev has been registered. Call unregister_netdev/free_netdev only when the corresponding state bits are set. Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-04-15ice: Drop leading underscores in enum ice_pf_stateAnirudh Venkataramanan8-187/+187
Remove the leading underscores in enum ice_pf_state. This is not really communicating anything and is unnecessary. No functional change. Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-04-15ice: use kernel definitions for IANA protocol ports and ether-typesBruce Allan4-8/+8
The well-known IANA protocol port 3260 (iscsi-target 0x0cbc) and the ether-types 0x8906 (ETH_P_FCOE) and 0x8914 (ETH_P_FIP) are already defined in kernel header files. Use those definitions instead of open-coding the same. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-04-15net/mlx5e: fix ingress_ifindex check in mlx5e_flower_parse_metawenxu1-0/+3
In the nft_offload there is the mate flow_dissector with no ingress_ifindex but with ingress_iftype that only be used in the software. So if the mask of ingress_ifindex in meta is 0, this meta check should be bypass. Fixes: 6d65bc64e232 ("net/mlx5e: Add mlx5e_flower_parse_meta support") Signed-off-by: wenxu <wenxu@ucloud.cn> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-15net/mlx5e: Fix setting of RS FEC modeAya Levin1-19/+4
Change register setting from bit number to bit mask. Fixes: b5ede32d3329 ("net/mlx5e: Add support for FEC modes based on 50G per lane links") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-15net/mlx5: Fix setting of devlink traps in switchdev modeAya Levin1-0/+5
Prevent setting of devlink traps on the uplink while in switchdev mode. In this mode, it is the SW switch responsibility to handle both packets with a mismatch in destination MAC or VLAN ID. Therefore, there are no flow steering tables to trap undesirable packets and driver crashes upon setting a trap. Fixes: 241dc159391f ("net/mlx5: Notify on trap action by blocking event") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-15Merge tag 'linux-can-next-for-5.13-20210414' of ↵David S. Miller1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2021-04-14 this is a pull request of a single patch for net-next/master. Vincent Mailhol's patch fixes a NULL pointer dereference when handling error frames in the etas_es58x driver, which has been added in the previous PR. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15Merge tag 'mlx5-updates-2021-04-13' of ↵David S. Miller24-776/+961
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5-updates-2021-04-13 mlx5 core and netdev driver updates 1) E-Switch updates from Parav, 1.1) Devlink parameter to control mlx5 metadata enablement for E-Switch 1.2) Trivial cleanups for E-Switch code 1.3) Dynamically allocate vport steering namespaces only when required 2) From Jianbo, Use variably sized data structures for Software steering 3) Several minor cleanups ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15Merge branch '10GbE' of ↵David S. Miller2-3/+15
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2021-04-14 This series contains updates to ixgbe and ice drivers. Alex Duyck fixes a NULL pointer dereference for ixgbe. Yongxin Liu fixes an unbalanced enable/disable which was causing a call trace with suspend for ixgbe. Colin King fixes a potential infinite loop for ice. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15Revert "net: stmmac: re-init rx buffers when mac resume back"Thierry Reding1-83/+1
This reverts commit 9c63faaa931e443e7abbbee9de0169f1d4710546, which introduces a suspend/resume regression on Jetson TX2 boards that can be reproduced every time. Given that the issue that this was supposed to fix only occurs very sporadically the safest course of action is to revert before v5.12 and then we can have another go at fixing the more rare issue in the next release (and perhaps backport it if necessary). The root cause of the observed problem seems to be that when the system is suspended, some packets are still in transit. When the descriptors for these buffers are cleared on resume, the descriptors become invalid and cause a fatal bus error. Link: https://lore.kernel.org/r/708edb92-a5df-ecc4-3126-5ab36707e275@nvidia.com/ Reported-by: Jonathan Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15net: enetc: fetch MAC address from device treeMichael Walle1-16/+49
Normally, the bootloader will already initialize the MAC address registers of the ENETC and the driver will just use them or generate a random one, if it is not initialized. Add a new way to provide the MAC address: via device tree. Besides the usual 'mac-address' property, there is also the possibility to fetch it via a NVMEM provider. The sl28 board stores the MAC address in the SPI NOR flash OTP region. Having this will allow linux to fetch the MAC address from there without being dependent on the bootloader. No in-tree boards have the device tree properties set, thus for these, this is a no-op. Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15cavium/liquidio: Fix duplicate argumentWan Jiabing1-1/+1
Fix the following coccicheck warning: ./drivers/net/ethernet/cavium/liquidio/cn66xx_regs.h:413:6-28: duplicated argument to & or | The CN6XXX_INTR_M1UPB0_ERR here is duplicate. Here should be CN6XXX_INTR_M1UNB0_ERR. Signed-off-by: Wan Jiabing <wanjiabing@vivo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14net: macb: fix the restore of cmp registersClaudiu Beznea1-1/+1
Commit a14d273ba159 ("net: macb: restore cmp registers on resume path") introduces the restore of CMP registers on resume path. In case the IP doesn't support type 2 screeners (zero on DCFG8 register) the struct macb::rx_fs_list::list is not initialized and thus the list_for_each_entry(item, &bp->rx_fs_list.list, list) loop introduced in commit a14d273ba159 ("net: macb: restore cmp registers on resume path") will access an uninitialized list leading to crash. Thus, initialize the struct macb::rx_fs_list::list without taking into account if the IP supports type 2 screeners or not. Fixes: a14d273ba159 ("net: macb: restore cmp registers on resume path") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14sfc: Remove duplicate argumentWan Jiabing1-1/+0
Fix the following coccicheck warning: ./drivers/net/ethernet/sfc/enum.h:80:7-28: duplicated argument to | Signed-off-by: Wan Jiabing <wanjiabing@vivo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14vrf: fix a comment about loopback deviceNicolas Dichtel1-6/+4
This is a leftover of the below commit. Fixes: 4f04256c983a ("net: vrf: Drop local rtable and rt6_info") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14ibmvnic: remove duplicate napi_schedule call in open functionLijun Pan1-5/+0
Remove the unnecessary napi_schedule() call in __ibmvnic_open() since interrupt_rx() calls napi_schedule_prep/__napi_schedule during every receive interrupt. Fixes: ed651a10875f ("ibmvnic: Updated reset handling") Signed-off-by: Lijun Pan <lijunp213@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14ibmvnic: remove duplicate napi_schedule call in do_reset functionLijun Pan1-5/+1
During adapter reset, do_reset/do_hard_reset calls ibmvnic_open(), which will calls napi_schedule if previous state is VNIC_CLOSED (i.e, the reset case, and "ifconfig down" case). So there is no need for do_reset to call napi_schedule again at the end of the function though napi_schedule will neglect the request if napi is already scheduled. Fixes: ed651a10875f ("ibmvnic: Updated reset handling") Signed-off-by: Lijun Pan <lijunp213@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14ibmvnic: avoid calling napi_disable() twiceLijun Pan1-2/+1
__ibmvnic_open calls napi_disable without checking whether NAPI polling has already been disabled or not. This could cause napi_disable being called twice, which could generate deadlock. For example, the first napi_disable will spin until NAPI_STATE_SCHED is cleared by napi_complete_done, then set it again. When napi_disable is called the second time, it will loop infinitely because no dev->poll will be running to clear NAPI_STATE_SCHED. To prevent above scenario from happening, call ibmvnic_napi_disable() which checks if napi is disabled or not before calling napi_disable. Fixes: bfc32f297337 ("ibmvnic: Move resource initialization to its own routine") Suggested-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: Lijun Pan <lijunp213@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14r8169: don't advertise pause in jumbo modeHeiner Kallweit1-2/+7
It has been reported [0] that using pause frames in jumbo mode impacts performance. There's no available chip documentation, but vendor drivers r8168 and r8125 don't advertise pause in jumbo mode. So let's do the same, according to Roman it fixes the issue. [0] https://bugzilla.kernel.org/show_bug.cgi?id=212617 Fixes: 9cf9b84cc701 ("r8169: make use of phy_set_asym_pause") Reported-by: Roman Mamedov <rm+bko@romanrm.net> Tested-by: Roman Mamedov <rm+bko@romanrm.net> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14r8169: add support for pause ethtool opsHeiner Kallweit1-0/+28
This adds support for the [g|s]et_pauseparam ethtool ops. It considers that the chip doesn't support pause frame use in jumbo mode. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14Merge branch '10GbE' of ↵David S. Miller4-8/+5
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue Tony Nguyen says: ==================== 10GbE Intel Wired LAN Driver Updates 2021-04-13 This series contains updates to ixgbe and ixgbevf driver. Jostar Yang adds support for BCM54616s PHY for ixgbe. Chen Lin removes an unused function pointer for ixgbe and ixgbevf. Bhaskar Chowdhury fixes a typo in ixgbe. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14net: stmmac: Add support for external trigger timestampingTan Tee Min7-1/+99
The Synopsis MAC controller supports auxiliary snapshot feature that allows user to store a snapshot of the system time based on an external event. This patch add supports to the above mentioned feature. Users will be able to triggered capturing the time snapshot from user-space using application such as testptp or any other applications that uses the PTP_EXTTS_REQUEST ioctl request. Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Tan Tee Min <tee.min.tan@intel.com> Co-developed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14net: phy: marvell-88x2222: swap 1G/10G modes on autonegIvan Bornyakov1-28/+89
Setting 10G without autonegotiation is invalid according to phy_ethtool_ksettings_set(). Thus, we need to set it during autonegotiation. If 1G autonegotiation can't complete for quite a time, but there is signal in line, switch line interface type to 10GBase-R, if supported, in hope for link to be established. And vice versa. If 10GBase-R link can't be established for quite a time, and autonegotiation is enabled, and there is signal in line, switch line interface type to appropriate 1G mode, i.e. 1000Base-X or SGMII, if supported. Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14net: phy: marvell-88x2222: move read_status after config_anegIvan Bornyakov1-98/+98
No functional changes, just move read link status routines below autonegotiation configuration to make future functional changes more distinct. Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14net: phy: marvell-88x2222: check that link is operationalIvan Bornyakov1-0/+43
Some SFP modules uses RX_LOS for link indication. In such cases link will be always up, even without cable connected. RX_LOS changes will trigger link_up()/link_down() upstream operations. Thus, check that SFP link is operational before actual read link status. If there is no SFP cage connected to the tranciever, check only PMD Recieve Signal Detect register. Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-14net/mlx5e: Fix RQ creation flow for queues which doesn't support XDPAya Levin1-2/+3
Allow to create an RQ which is not registered as an XDP RQ. For example: the trap-RQ doesn't register as an XDP RQ. Fixes: 869c5f926247 ("net/mlx5e: Generalize open RQ") Signed-off-by: Aya Levin <ayal@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: Replace spaces with tab at the start of a lineWenpeng Liang1-1/+1
There should be no spaces at the start of the line. Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com> Signed-off-by: Weihang Li <liweihang@huawei.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: Remove return statement exist at the end of void functionWenpeng Liang3-4/+0
void function return statements are not generally useful. Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com> Signed-off-by: Weihang Li <liweihang@huawei.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: Add a blank line after declarationsWenpeng Liang2-2/+3
There should be a blank lines after declarations. Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com> Signed-off-by: Weihang Li <liweihang@huawei.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: Fix bit-wise and with zeroColin Ian King1-1/+1
The bit-wise and of the action field with MLX5_ACCEL_ESP_ACTION_DECRYPT is incorrect as MLX5_ACCEL_ESP_ACTION_DECRYPT is zero and not intended to be a bit-flag. Fix this by using the == operator as was originally intended. Addresses-Coverity: ("Logically dead code") Fixes: 7dfee4b1d79e ("net/mlx5: IPsec, Refactor SA handle creation and destruction") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: DR, Alloc cmd buffer with kvzalloc() instead of kzalloc()Roi Dayan2-5/+5
The cmd size is 8K so use kvzalloc(). Signed-off-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: DR, Use variably sized data structures for different actionsJianbo Liu4-159/+199
mlx5dr_action is a generally used data structure, and there is an union for different types of actions in it. The size of mlx5dr_action is about 72 bytes, but for those actions with fewer fields, most of the allocated memory is wasted. Remove this union, and mlx5dr_action becomes a generic action header. Then actions are dynamically allocated with needed memory, the data for each action is stored right after the header. Signed-off-by: Jianbo Liu <jianbol@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: SF, Reuse stored hardware function idParav Pandit1-3/+2
SF's hardware function id is already stored in mlx5_sf. Reuse it, instead of querying the hw table. Signed-off-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: SF, Use device pointer directlyParav Pandit1-8/+8
At many places in the code, device pointer is directly available. Make use of it, instead of accessing it from the table. Signed-off-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: E-Switch, Initialize eswitch acls ns when eswitch is enabledParav Pandit3-55/+93
Currently eswitch flow steering (FS) namespace of vport's ingress and egress ACL are enabled when FS layer is initialized. This is done even when eswitch is diabled. This demands that total eswitch ports to be known to FS layer without eswitch in use. Given the FS core is not dependent on eswitch, make namespace init and cleanup routines as helper routines to be invoked only when eswitch is needed. With this change, ingress and egress ACL namespaces are created only when eswitch legacy/offloads mode is enabled. Signed-off-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: E-Switch, Move legacy code to a individual fileParav Pandit5-507/+539
Currently eswitch offers two modes. Legacy and offloads. Offloads code is already in its own file eswitch_offloads.c However eswitch.c contains the eswitch legacy code and common infrastructure code. To enable future extensions and to better manage generic common eswitch infrastructure code, move the legacy code to its own legacy.c file. Signed-off-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: E-Switch, Convert a macro to a helper routineParav Pandit2-17/+20
Convert ESW_ALLOWED macro to a helper routine so that it can be used in other eswitch files. Signed-off-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: E-Switch Make cleanup sequence mirror of initParav Pandit1-2/+1
Make cleanup sequence mirror of init sequence for cleaning up reps and freeing vports. Also when reps initialization fails, there is no need to perform reps cleanup. Signed-off-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: E-Switch, Make vport number u16Parav Pandit2-2/+3
Vport number is 16-bit field in hardware. Make it u16. Move location of vport in the structure so that it reduces a hole in the structure. Signed-off-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: E-Switch, Skip querying SF enabled bitsParav Pandit1-6/+0
With vhca events, SF state is queried through the VHCA events. Device no longer expects SF bitmap in the query eswitch functions command. Hence, remove it to simplify the code. Signed-off-by: Parav Pandit <parav@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-04-14net/mlx5: E-Switch, let user to enable disable metadataParav Pandit4-7/+88
Currently each packet inserted in eswitch is tagged with a internal metadata to indicate source vport. Metadata tagging is not always needed. Metadata insertion is needed for multi-port RoCE, failover between representors and stacked devices. In many other cases, metadata enablement is not needed. Metadata insertion slows down the packet processing rate of the E-switch when it is in switchdev mode. Below table show performance gain with metadata disabled for VXLAN offload rules in both SMFS and DMFS steering mode on ConnectX-5 device. ---------------------------------------------- | steering | metadata | pkt size | rx pps | | mode | | | (million) | ---------------------------------------------- | smfs | disabled | 128Bytes | 42 | ---------------------------------------------- | smfs | enabled | 128Bytes | 36 | ---------------------------------------------- | dmfs | disabled | 128Bytes | 42 | ---------------------------------------------- | dmfs | enabled | 128Bytes | 36 | ---------------------------------------------- Hence, allow user to disable metadata using driver specific devlink parameter. Metadata setting of the eswitch is applicable only for the switchdev mode. Example to show and disable metadata before changing eswitch mode: $ devlink dev param show pci/0000:06:00.0 name esw_port_metadata pci/0000:06:00.0: name esw_port_metadata type driver-specific values: cmode runtime value true $ devlink dev param set pci/0000:06:00.0 \ name esw_port_metadata value false cmode runtime $ devlink dev eswitch set pci/0000:06:00.0 mode switchdev Signed-off-by: Parav Pandit <parav@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Vu Pham <vuhuong@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> --- changelog: v1->v2: - added performance numbers in commit log - updated commit log and documentation for switchdev mode - added explicit note on when user can disable metadata in documentation
2021-04-14iwlwifi: dbg: disable ini debug in 9000 family and belowMukesh Sisodiya1-2/+3
Yoyo based debug is not applicable to old devices. As init debug is enabled by default in the driver, it needs to be disabled to work the old debug mechanism in old devices. Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com> Fixes: b0d8d2c27007 ("iwlwifi: yoyo: enable yoyo by default") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210411132130.805401a1b8ec.I30db38184a418cfc1c5ca1a305cc14a52501d415@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2021-04-14iwlwifi: pcie: Change ma product string nameMatti Gottlieb3-5/+5
Change ma product string name to the correct name, and to reflect the CRF and not the CNV. Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210411132130.c05b4c55540f.I8dd0361b033f63658999ba53640949701b048f17@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2021-04-14iwlwifi: fw: print out trigger delay when collecting dataJohannes Berg1-1/+3
It can be confusing to see "Collecting data: ..." followed by that not actually happening immediately so print out the delay in that message. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210411132130.5bd095dc579a.Id1f3b746ac61497951638ba7ce70fc4b63dd87d1@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2021-04-14iwlwifi: trans/pcie: defer transport initialisationJohannes Berg3-39/+57
In a few PCIe devices we may have to swap out the configuration after we allocate/initialise some parts of the device because we only know the correct one after reading some registers. This causes some things such as the byte-count table allocations to be incorrect, since the configuration is swapped for one with a bigger queue size. Fix this by initialising most of the transport much later, only after the configuration has finally been determined. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210411132130.8f5db97db1e4.Ic622da559b586a04ca536a0ec49ed5ecf03a9354@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2021-04-14iwlwifi: bump FW API to 63 for AX devicesLuca Coelho1-1/+1
Start supporting API version 63 for AX devices. Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210411132130.a588a9dacd98.Ie4f96b8988c2cbd5f096ee64d0eb0f4829d55aee@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2021-04-14iwlwifi: mvm: don't WARN if we can't remove a time eventEmmanuel Grumbach1-2/+2
It is not very useful to WARN if we can't send a host command The firmware is likely in a bad situation and the fact that we didn't send the host command has an impact on the firmware only, not on the driver. The driver could clean up all its state. Don't WARN in this case, but just leave a smaller note. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210411132130.0324abc169c8.I4f9b769bc38d68f8ed43f77d2cd75e8f1993e964@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2021-04-14iwlwifi: mvm: don't disconnect immediately if we don't hear beacons after CSAEmmanuel Grumbach1-1/+12
When we switch channel, we may miss a few beacons on the new channel. Don't disconnect if the time event for the switch ends before we hear the beacons. Note that this is relevant only for old devices that still use the TIME_EVENT firmware API for channel switch. The check that we hear a beacon before the time event ends was meant to be used for the association time event and not for the channel switch time event. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210411132130.3d710091a0bd.I37a161ffdfb099a10080fbdc3b70a4deb76952e2@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2021-04-14iwlwifi: rs-fw: don't support stbc for HE 160Mordechay Goodstein1-12/+8
Our HE doesn't support it so never set HE 160 stbc Fixes: 3e467b8e4cf4 ("iwlwifi: rs-fw: enable STBC in he correctly") Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210411124418.550fd1903eb7.I8ddbc2f87044a5ef78d916c9c59be797811a1b7f@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-10-03 10:11:50 +0300