summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2018-01-26mt76: retry rx polling as long as there is budget leftFelix Fietkau1-3/+7
Sending frames to mac80211 needs time, which could allow for more rx packets to end up in the DMA ring. Retry polling until there are no more frames left. Improves rx latency under load. Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-26net: vrf: Add support for sends to local broadcast addressDavid Ahern1-2/+3
Sukumar reported that sends to the local broadcast address (255.255.255.255) are broken. Check for the address in vrf driver and do not redirect to the VRF device - similar to multicast packets. With this change sockets can use SO_BINDTODEVICE to specify an egress interface and receive responses. Note: the egress interface can not be a VRF device but needs to be the enslaved device. https://bugzilla.kernel.org/show_bug.cgi?id=198521 Reported-by: Sukumar Gopalakrishnan <sukumarg1973@gmail.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26r8169: fix memory corruption on retrieval of hardware statistics.Francois Romieu1-7/+2
Hardware statistics retrieval hurts in tight invocation loops. Avoid extraneous write and enforce strict ordering of writes targeted to the tally counters dump area address registers. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Tested-by: Oliver Freyermuth <o.freyermuth@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26mlxsw: use tc_cls_can_offload_and_chain0()Jakub Kicinski1-4/+2
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case ethtool tc offload flag is not set or chain unsupported. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26i40e: use tc_cls_can_offload_and_chain0()Jakub Kicinski1-5/+3
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case ethtool tc offload flag is not set or chain unsupported. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26ixgbe: use tc_cls_can_offload_and_chain0()Jakub Kicinski1-4/+1
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case ethtool tc offload flag is not set or chain unsupported. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26bnxt: use tc_cls_can_offload_and_chain0()Jakub Kicinski3-5/+4
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case ethtool tc offload flag is not set or chain unsupported. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26mlx5: use tc_cls_can_offload_and_chain0()Jakub Kicinski2-8/+2
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case ethtool tc offload flag is not set or chain unsupported. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26cxgb4: use tc_cls_can_offload_and_chain0()Jakub Kicinski1-7/+1
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case ethtool tc offload flag is not set or chain unsupported. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26nfp: use tc_cls_can_offload_and_chain0()Jakub Kicinski2-7/+4
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case ethtool tc offload flag is not set or chain unsupported. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26netdevsim: use tc_cls_can_offload_and_chain0()Jakub Kicinski1-4/+1
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case ethtool tc offload flag is not set or chain unsupported. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26qed: code indent should use tabs where possibleRohit Visavalia1-5/+5
Issue found by checkpatch. Signed-off-by: Rohit Visavalia <rohit.visavalia@softnautics.com> Acked-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26be2net: networking block comments don't use an empty /* lineRohit Visavalia1-2/+1
Resolved Warning: networking block comments don't use an empty /* line, use /* Comment... Issue found by checkpatch. Signed-off-by: Rohit Visavalia <rohit.visavalia@softnautics.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26cxgb4: fix possible deadlockGanesh Goudar1-10/+10
t4_wr_mbox_meat_timeout() can be called from both softirq context and process context, hence protect the mbox with spin_lock_bh() instead of simple spin_lock() Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26net: don't call update_pmtu unconditionallyNicolas Dichtel2-6/+4
Some dst_ops (e.g. md_dst_ops)) doesn't set this handler. It may result to: "BUG: unable to handle kernel NULL pointer dereference at (null)" Let's add a helper to check if update_pmtu is available before calling it. Fixes: 52a589d51f10 ("geneve: update skb dst pmtu on tx path") Fixes: a93bf0ff4490 ("vxlan: update skb dst pmtu on tx path") CC: Roman Kapl <code@rkapl.cz> CC: Xin Long <lucien.xin@gmail.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26sfc: support Medford2 frequency adjustment formatLaurence Evans1-14/+31
Support increased precision frequency adjustment format (FP44) used by Medford2 adapters. Signed-off-by: Laurence Evans <levans@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26sfc: support second + quarter ns time format for receive datapathEdward Cree1-33/+106
The time_format that we stash in the PTP data structure is never referenced, so we can remove it. Instead, store the information needed to interpret sync event timestamps. Also rolls in a couple of other related minor PTP fixes. Based on patches by Bert Kenward <bkenward@solarflare.com> and Laurence Evans <levans@solarflare.com>. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26sfc: support separate PTP and general timestampingLaurence Evans1-15/+43
Support MC_CMD_PTP_OUT_GET_TIMESTAMP_CORRECTIONS_V2. Extract general timestamp corrections in addition to PTP corrections. Apply receive timestamp corrections for general datapath receive timestamping, and correspondingly for transmit. Signed-off-by: Laurence Evans <levans@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26sfc: simplify RX datapath timestampingLaurence Evans1-8/+5
Use timestamp conversion function with correction to avoid duplicate correction handling. Signed-off-by: Laurence Evans <levans@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26sfc: only advertise TX timestamping if we have the license for itMartin Habets2-1/+16
We check the license for TX hardware timestamping capability. The PTP probe will have enabled PTP sync events from the adapter. If later, at TX queue init, it turns out we do not have the license, we don't need the sync events either. Signed-off-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26sfc: on 8000 series use TX queues for TX timestampsEdward Cree6-13/+54
For this we create and use one or more new TX queues on the PTP channel, and enable sync events for it. Based on a patch by Martin Habets <mhabets@solarflare.com>. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26sfc: MAC TX timestamp handling on the 8000 seriesMartin Habets2-2/+46
TX timestamps on 8000 series are supplied from the MAC. This timestamp is only 48 bits long. The high order bits from the last time sync event are used for the top 16 bits. Signed-off-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26sfc: only enable TX timestamping if the adapter is licensed for itMartin Habets2-0/+29
If we try to enable the feature and do not have the license for it, the MCPU will refuse and fail our TX queue init. Signed-off-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26sfc: use main datapath for HW timestamps if availableMartin Habets2-15/+42
We can now transmit SKBs in 2 ways: 1. Via the MC (for the 7XXX series and earlier), using efx_ptp_xmit_skb_mc(). 2. Via the TX queues on the dedicated PTP channel (8XXX series and later), using efx_ptp_xmit_skb_queue(). The PTP worker thread uses the method set up at probe time. It never checked the return code from the old efx_ptp_xmit_skb(), so it now returns void. We increment the TX dropped counter of the device if the transmit fails. As a result of the probe per channel the remove gets called multiple times. Clean up efx->ptp_data properly to avoid the 2nd call blowing up. Signed-off-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26sfc: add function to determine which TX timestamping method to useMartin Habets2-0/+11
Use MC capability MC_CMD_GET_CAPABILITIES_V2_OUT_TX_MAC_TIMESTAMPING to detect whether the NIC supports timestamping packets sent out the main datapath. Signed-off-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26sfc: handle TX timestamps in the normal data pathMartin Habets5-9/+119
Before this work, TX timestamping is done by sending each SKB to the MC. On the 8000 series (Medford1) we have high speed timestamping via the MAC, which means we can use normal TX queues for this without a significant drop in bandwidth. On the X2000 series (Medford2) support for transmitting via the MC is removed, so the new way must be used. This patch enables timestamping on a TX queue, if requested. It also enhances TX event handling to process the extra completion events, and puts the time in the SKB. Signed-off-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-26sfc: remove tx and MCDI handling from NAPI budget considerationBert Kenward2-30/+7
The NAPI budget is only for RX processing work, not other work such as TX or MCDI completion handling. Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-25Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo14-89/+752
ath.git patches for 4.16. Major changes: wil6210 * add PCI device id for Talyn * support flashless device ath9k * improve RSSI/signal accuracy on AR9003 series
2018-01-25rtlwifi: btcoex: Fix some static warnings from SparsePing-Ke Shih2-25/+15
Add 'static' or declaration to resolve the warnings, and remove two unused functions halbtc_set_macreg() and halbtc_get_macreg() exposed when they were made static. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25wcn36xx: release DMA memory in case of errorRamon Fried1-6/+40
wcn36xx_dxe_init() doesn't check for the return value of wcn36xx_dxe_init_descs(), release the resources in case an error ocurred. Signed-off-by: Ramon Fried <rfried@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25ath9k: Display calibration data piers in debugfsWojciech Dubowik1-1/+63
Display per frequency calibration data in dump_modal debugfs entry including reference power, voltage, tx temperature and noise floor. Example of chain 0 of OEM card (dump from modal_eeprom): Chain 0 Freq ref volt temp nf_Cal nf_Pow rx_temp 5180 -30 0 137 0 0 0 5320 -24 0 137 0 0 0 5500 -15 0 137 0 0 0 5620 -10 0 137 0 0 0 5700 -15 0 137 0 0 0 5745 -16 0 135 0 0 0 5785 -19 0 136 0 0 0 5825 -22 0 136 0 0 0 Example of a card with calibrated noise floor. Chain 0 Freq ref volt temp nf_Cal nf_Pow rx_temp 4890 -49 0 128 -107 -97 124 5100 -23 0 128 -101 -96 124 5180 -18 0 128 -101 -96 124 5300 -12 0 128 -102 -97 124 5500 -9 0 128 -101 -97 125 5640 -17 0 128 -101 -98 124 5785 -25 0 128 -101 -98 124 5940 -33 0 128 -106 -99 124 Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25ath9k: Use calibrated noise floor value when availableWojciech Dubowik1-14/+24
AR9003 series allows to calibrate noise floor for different frequency bins. Once it's done it's possible to get more accurate rssi/signal values over whole frequency band at a given temperature. The RSSI/signal accuracy reported by calibrated RF cards improves from 6 to up to 2dB. This could be interesting for application which require good signal accuracy like roaming or mesh protocols. Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25ath9k: Read noise floor calibration data from eepromWojciech Dubowik3-8/+67
AR9003 devices can have calibrated noise floor values which can be used instead of hard coded one. Read them from eeprom and save interpolated value in nf limits for the current channel. Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25ath9k: Alternative EEPROM size for AR9003Wojciech Dubowik1-0/+6
AR9003 factory calibration allows to use bigger EEPROM than standard 1k without changing the default layout. Allow probing of EEPROM at alternative address if initial check for default fails. The original ar9003 eeprom ops are still be used. Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25wil6210: support parsing brd file address from fw fileMaya Erez4-11/+184
In order to allow using the same brd file across different 11ad chips, the address for loading the brd file should be part of the FW file, instead of the brd file. The brd file is expected to include only one section. To allow backward compatibility the driver reads the address from the brd file in case it is not included in the FW file. Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25wil6210: enlarge FW mac_rgf_ext section for Sparrow D0Lior David3-3/+18
Sparrow D0 chips have slightly larger mac_rgf_ext section in order to support extra features such as multiple virtual interfaces. Signed-off-by: Lior David <liord@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25wil6210: fix random failure to bring network interface upLior David5-2/+138
Currently when we want to bring the interface up, we first reset the device which causes the boot loader to run. Then we halt the device CPU, load FW image and resume the device CPU. There are some boot loader versions which perform redundant memory accesses even when idle. Halting the device CPU while boot loader access memory can cause the device memory controller to get stuck, the FW will fail to load and the network interface will not come up. For such boot loaders implement a workaround where we freeze the boot loader before halting the device CPU, so it will not perform any memory accesses. Signed-off-by: Lior David <liord@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25wil6210: configure OTP HW vectors in SW reset flowMaya Erez2-0/+26
OTP HW vectors values are different for 40MHz and 330MHz AHB clocks. In SW reset flow, the host driver sets the clock frequency to 40MHz. In order to allow reading from the OTP, the host driver should configure the OTP HW vectors with the values that fits this clock frequency. Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25wil6210: support flashless deviceDedy Lansky3-29/+87
Talyn device supports boot without flash. Driver detects flashless device and in this case waits for ready indication from HW machine (instead of bootloader ready indication). Also in this case, MAC address is retrieved from OTP. Signed-off-by: Dedy Lansky <dlansky@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25wil6210: add support for Talyn AHB address mapMaya Erez4-17/+92
Talyn memory has changed, areas were increased and shifted to new locations. Use the appropriate address map according to the device JTAG ID. Signed-off-by: Dedy Lansky <dlansky@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25wil6210: recognize Talyn JTAG IDMaya Erez2-0/+7
Add Talyn JTAG ID to the list of valid IDs and identify this device as Talyn. Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25wil6210: add Talyn PCIe device IDMaya Erez1-0/+2
PCIe device ID has changed in Talyn. Add this ID to wil6210_pcie_ids list to allow recognition of Talyn device. Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25ath9k: discard undersized packetsFelix Fietkau1-2/+2
Sometimes the hardware will push small packets that trigger a WARN_ON in mac80211. Discard them early to avoid this issue. Reported-by: Stijn Tintel <stijn@linux-ipv6.be> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-01-25Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller7-29/+37
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-25net/ibm/emac: wrong bit is used for STA control register writeIvan Mikhaylov1-1/+1
STA control register has areas of mode and opcodes for opeations. 18 bit is using for mode selection, where 0 is old MIO/MDIO access method and 1 is indirect access mode. 19-20 bits are using for setting up read/write operation(STA opcodes). In current state 'read' is set into old MIO/MDIO mode with 19 bit and write operation is set into 18 bit which is mode selection, not a write operation. To correlate write with read we set it into 20 bit. All those bit operations are MSB 0 based. Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-25net/ibm/emac: add 8192 rx/tx fifo sizeIvan Mikhaylov2-0/+8
emac4syn chips has availability to use 8192 rx/tx fifo buffer sizes, in current state if we set it up in dts 8192 as example, we will get only 2048 which may impact on network speed. Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-25Merge branch '100GbE' of ↵David S. Miller3-17/+43
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue Jeff Kirsher says: ==================== 100GbE Intel Wired LAN Driver Updates 2018-01-24 This series contains updates to fm10k only. Alex fixes MACVLAN offload for fm10k, where we were not seeing unicast packets being received because we did not correctly configure the default VLAN ID for the port and defaulting to 0. Jake cleans up unnecessary parenthesis in a couple of "if" statements. Fixed the driver to stop adding VLAN 0 into the VLAN table, since it would cause the VLAN table to be inconsistent between the PF and VF. Also fixed an issue where we were assuming that VLAN 1 is enabled when the default VLAN ID is not set, so resolve by not requesting any filters for the default_vid if it has not yet been assigned. Ngai fixes an issue which was generating a dmesg regarding unbale to kill a particular VLAN ID for the device. This is due to ndo_vlan_rx_kill_vid() exits with an error and the handler for this ndo is fm10k_update_vid() which exits prematurely under PF VLAN management. So to resolve, we must check the VLAN update action type before exiting fm10k_update_vid(), and act appropriately based on the action type. Also corrected code comment typos. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-25fm10k: clarify action when updating the VLAN tableNgai-Mint Kwan1-1/+3
Clarify the comment for when entering promiscuous mode that we update the VLAN table. Add a comment distinguishing the case where we're exiting promiscuous mode and need to clear the entire VLAN table. Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@gmail.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-01-25fm10k: correct typo in fm10k_pf.cNgai-Mint Kwan1-1/+1
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-01-25fm10k: don't assume VLAN 1 is enabledJacob Keller1-5/+3
Since commit 856dfd69e84f ("fm10k: Fix multicast mode synch issues", 2016-03-03) we've incorrectly assumed that VLAN 1 is enabled when the default VID is not set. This occurs because we check the default_vid and if it's zero, start several loops over the active_vlans bitmask at 1, instead of checking to ensure that that bit is active. This happened because of commit d9ff3ee8efe9 ("fm10k: Add support for VLAN 0 w/o default VLAN", 2014-08-07) which mistakenly assumed that we should send requests for MAC and VLAN filters with VLAN 0 when the default_vid isn't set. However, the switch generally considers this an invalid configuration, so the only time we'd have a default_vid of 0 is when the switch is down. Instead, lets just not request any filters for the default_vid if it's not yet been assigned. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-30 23:45:19 +0300