| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add support for mcan bit timing and control mode according to bosch mcan IP
version 3.3.0. The mcan version read from the Core Release field of CREL
register would be 33. Accordingly the properties are to be set for mcan v3.3.0
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/1606366302-5520-1-git-send-email-pankj.sharma@samsung.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
At lest the revision 3.3.0 of the bosch m_can IP core specifies that valid
register values for "Nominal Time segment after sample point (NTSEG2)" are from
1 to 127. As the hardware uses a value of one more than the programmed value,
mean tseg2_min is 2.
This patch fixes the tseg2_min value accordingly.
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Mario Huettel <mario.huettel@gmx.net>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Link: https://lore.kernel.org/r/20201124190751.3972238-1-mkl@pengutronix.de
Fixes: b03cfc5bb0e1 ("can: m_can: Enable M_CAN version dependent initialization")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
request_threaded_irq()'s flags
The threaded IRQ handler is used for the tcan4x5x driver only. The IRQ pin of
the tcan4x5x controller is active low, so better not use IRQF_TRIGGER_FALLING
when requesting the IRQ. As this can result in missing interrupts.
Further, if the device tree specified the interrupt as "IRQ_TYPE_LEVEL_LOW",
unloading and reloading of the driver results in the following error during
ifup:
| irq: type mismatch, failed to map hwirq-31 for gpio@20a8000!
| tcan4x5x spi1.1: m_can device registered (irq=0, version=32)
| tcan4x5x spi1.1 can2: TCAN4X5X successfully initialized.
| tcan4x5x spi1.1 can2: failed to request interrupt
This patch fixes the problem by removing the IRQF_TRIGGER_FALLING from the
request_threaded_irq().
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Cc: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/20201127093548.509253-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When eswitch manager is running on ECPF, host PF should be treated
as non eswitch manager port, similar to other VF vports.
Fail to do so, results in firmware treating PF's vport as ECPF
vport for eswitch ACL tables.
Non zero check to figure out if a given vport is other vport or not
is not sufficient becase PF vport number = 0 on ECPF.
Hence, create esw acl tables with an attribute of other vport.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently ECPF enables external host PF too early in the initialization
sequence for Ethernet links when ECPF is eswitch manager.
Due to this, when external host PF driver is loaded, host PF's HCA CAP has
inner_ip_version supported by NIC RX flow table.
This capability is later updated by firmware after ECPF driver enables
ENCAP/DECAP as eswitch manager.
This results into a timing race condition, where CREATE_TIR command
fails with a below syndrome on host PF.
mlx5_cmd_check:775:(pid 510): CREATE_TIR(0x900) op_mod(0x0) failed,
status bad parameter(0x3), syndrome (0x562b00)
Hence, enable the external host PF after necessary eswitch and per vport
initialization is completed.
Continue to enable host PF when eswitch manager capability is off for a
ECPF.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
To match the hardware spec, rename peer_pf to host_pf.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Export
mlx5_create_flow_table()
mlx5_create_flow_group()
mlx5_destroy_flow_group().
These symbols are required by the VDPA implementation to create rules
that consume VDPA specific traffic.
We do not deal with putting the prototypes in a header file since they
already exist in include/linux/mlx5/fs.h.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add the upcoming BlueField-3 device ID.
Signed-off-by: Meir Lichtinger <meirl@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mlx5 command init and cleanup routines are internal to mlx5_core driver.
Hence, avoid exporting them and move their definition to mlx5_core
driver's internal file mlx5_core.h
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add misc4 match params to enable matching on prog_sample_fields.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This is to allow passing misc4 match param from userspace when
function like ib_flow_matcher_create is called.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The flow sampler object is a new destination type. Add a new member
for the flow destination.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This patch add a check to the mcp251xfd_probe() function to bail out and give
the user a proper error message if no IRQ is specified. Otherwise the driver
will probe just fine but ifup will fail with a meaningless "RTNETLINK answers:
Invalid argument" error message.
Link: https://lore.kernel.org/r/20201123113522.3820052-1-mkl@pengutronix.de
Reported-by: Niels Petter <petter@ka-long.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The firmware on the original USB2CAN by Geschwister Schneider Technologie
Entwicklungs- und Vertriebs UG exchanges all data between the host and the
device in host byte order. This is done with the struct
gs_host_config::byte_order member, which is sent first to indicate the desired
byte order.
The widely used open source firmware candleLight doesn't support this feature
and exchanges the data in little endian byte order. This breaks if a device
with candleLight firmware is used on big endianess systems.
To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which
is a transparent cookie) are converted to __le32.
Cc: Maximilian Schneider <max@schneidersoft.net>
Cc: Hubert Denkmair <hubert@denkmair.de>
Reported-by: Michael Rausch <mr@netadair.de>
Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2020-11-24
This series contains updates to i40e and igbvf drivers.
Marek removes a redundant assignment for i40e.
Stefan Assmann corrects reporting of VF link speed for i40e.
Karen revises a couple of error messages to warnings for igbvf as they
could be misinterpreted as issues when they are not.
v2: Dropped PTP patch as it's being updated.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igbvf: Refactor traces
i40e: report correct VF link speed when link state is set to enable
i40e: remove redundant assignment
====================
Link: https://lore.kernel.org/r/20201124165245.2844118-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the underlying read operation failed we would end up writing stale
data to the supplied buffer. This would end up with the last
successfully read value repeating. Fix this by only writing the data
when we know the read was good. This will mean that failed values will
return 0xffff.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MV88E6097 presents the serdes interrupts for ports 8 and 9 via the
Switch Global 2 registers. There is no additional layer of
enablinh/disabling the serdes interrupts like other mv88e6xxx switches.
Even though most of the serdes behaviour is the same as the MV88E6185
that chip does not provide interrupts for serdes events so unlike
earlier commits the functions added here are specific to the MV88E6097.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement serdes_power, serdes_get_lane and serdes_pcs_get_state ops for
the MV88E6097/6095/6185 so that ports 8 & 9 can be supported as serdes
ports and directly connected to other network interfaces or to SFPs
without a PHY.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a port is configured with 'managed = "in-band-status"' switch chips
like the 88E6390 need to propagate the SERDES link state to the MAC
because the link state is not correctly detected. This causes problems
on the 88E6185/88E6097 where the link partner won't see link state
changes because we're forcing the link.
To address this introduce a new device specific op port_sync_link() and
push the logic from mv88e6xxx_mac_link_up() into that. Provide an
implementation for the 88E6185 like devices which doesn't force the
link.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This should be done in the device driver instead of the device tree.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This should be done in the device driver instead of the device tree.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The dsa.yaml device tree binding allows "ethernet-ports" (preferred) and
"ports".
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently lock gets freed only if timeout expires, but missed a
case when HW returns failure and goes for cleanup.
Fixes: efca3878a5fb ("ch_ktls: Issue if connection offload fails")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Link: https://lore.kernel.org/r/20201125072626.10861-1-rohitm@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These are only used as input arguments to qmi_handle_init() which
accepts const pointers to both qmi_ops and qmi_msg_handler. Make them
const to allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201122234031.33432-2-rikard.falkeborn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The tc-taprio base time indicates the beginning of the tc-taprio
schedule, which is cyclic by definition (where the length of the cycle
in nanoseconds is called the cycle time). The base time is a 64-bit PTP
time in the TAI domain.
Logically, the base-time should be a future time. But that imposes some
restrictions to user space, which has to retrieve the current PTP time
from the NIC first, then calculate a base time that will still be larger
than the base time by the time the kernel driver programs this value
into the hardware. Actually ensuring that the programmed base time is in
the future is still a problem even if the kernel alone deals with this.
Luckily, the enetc hardware already advances a base-time that is in the
past into a congruent time in the immediate future, according to the
same formula that can be found in the software implementation of taprio
(in taprio_get_start_time):
/* Schedule the start time for the beginning of the next
* cycle.
*/
n = div64_s64(ktime_sub_ns(now, base), cycle);
*start = ktime_add_ns(base, (n + 1) * cycle);
There's only one problem: the driver doesn't let the hardware do that.
It interferes with the base-time passed from user space, by special-casing
the situation when the base-time is zero, and replaces that with the
current PTP time. This changes the intended effective base-time of the
schedule, which will in the end have a different phase offset than if
the base-time of 0.000000000 was to be advanced by an integer multiple
of the cycle-time.
Fixes: 34c6adf1977b ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201124220259.3027991-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The rtl8211f supports downshift and before commit 5502b218e001
("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
the read-back of register MII_CTRL1000 was used to detect the
negotiated link speed.
The code added in commit d445dff2df60 ("net: phy: realtek: read
actual speed to detect downshift") is working fine also for this
phy and it's trivial re-using it to restore the downshift
detection on rtl8211f.
Add the phy specific read_status() pointing to the existing
function rtlgen_read_status().
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Link: https://lore.kernel.org/r/478f871a-583d-01f1-9cc5-2eea56d8c2a7@huawei.com
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Link: https://lore.kernel.org/r/20201124230756.887925-1-antonio.borneo@st.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use recently introduced PTP_MSGTYPE_SYNC and PTP_MSGTYPE_DELAY_REQ
defines instead of a driver internal enumeration.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use recently introduced PTP wide defines instead of a driver internal
enumeration.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Cc: Petr Machata <petrm@mellanox.com>
Cc: Jiri Pirko <jiri@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace use of magic number with recently introduced define.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 757926247836 ("net: stmmac: add flexible PPS to dwmac
4.10a") was intended to modify the struct dwmac410_ops, but it got
somehow badly merged and modified the struct dwmac4_ops.
Revert the modification in struct dwmac4_ops and re-apply it
properly in struct dwmac410_ops.
Fixes: 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a")
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20201124223729.886992-1-antonio.borneo@st.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that all the PHY drivers have been migrated to directly implement
the generic .handle_interrupt() callback for a seamless support of
shared IRQs and all the .config_inter() implementations clear any
pending interrupts, we can safely remove the two callbacks.
With this patch, phylib has a proper support for shared IRQs (and not
just for multi-PHY devices. A PHY driver must implement both the
.handle_interrupt() and .config_intr() callbacks for the IRQs to be
actually used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Also, add a comment describing the multiple step interrupt
acknoledgement process.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Mathias Kresin <dev@kresin.me>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Mathias Kresin <dev@kresin.me>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Based on the discussion with Sukadev Bhattiprolu and Dany Madden,
we believe that checking adapter->resetting bit is preferred
since RESETTING state flag is not as strict as resetting bit.
RESETTING state flag is removed since it is verbose now.
Fixes: 7d7195a026ba ("ibmvnic: Do not process device remove during device reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
crq->msgs could be NULL if the previous reset did not complete after
freeing crq->msgs. Check for NULL before dereferencing them.
Snippet of call trace:
...
ibmvnic 30000003 env3 (unregistering): Releasing sub-CRQ
ibmvnic 30000003 env3 (unregistering): Releasing CRQ
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc0000000000c1a30
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: ibmvnic(E-) rpadlpar_io rpaphp xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables xsk_diag tcp_diag udp_diag tun raw_diag inet_diag unix_diag bridge af_packet_diag netlink_diag stp llc rfkill sunrpc pseries_rng xts vmx_crypto uio_pdrv_genirq uio binfmt_misc ip_tables xfs libcrc32c sd_mod t10_pi sg ibmvscsi ibmveth scsi_transport_srp dm_mirror dm_region_hash dm_log dm_mod [last unloaded: ibmvnic]
CPU: 20 PID: 8426 Comm: kworker/20:0 Tainted: G E 5.10.0-rc1+ #12
Workqueue: events __ibmvnic_reset [ibmvnic]
NIP: c0000000000c1a30 LR: c008000001b00c18 CTR: 0000000000000400
REGS: c00000000d05b7a0 TRAP: 0380 Tainted: G E (5.10.0-rc1+)
MSR: 800000000280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 44002480 XER: 20040000
CFAR: c0000000000c19ec IRQMASK: 0
GPR00: 0000000000000400 c00000000d05ba30 c008000001b17c00 0000000000000000
GPR04: 0000000000000000 0000000000000000 0000000000000000 00000000000001e2
GPR08: 000000000001f400 ffffffffffffd950 0000000000000000 c008000001b0b280
GPR12: c0000000000c19c8 c00000001ec72e00 c00000000019a778 c00000002647b440
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000006 0000000000000001 0000000000000003 0000000000000002
GPR24: 0000000000001000 c008000001b0d570 0000000000000005 c00000007ab5d550
GPR28: c00000007ab5c000 c000000032fcf848 c00000007ab5cc00 c000000032fcf800
NIP [c0000000000c1a30] memset+0x68/0x104
LR [c008000001b00c18] ibmvnic_reset_crq+0x70/0x110 [ibmvnic]
Call Trace:
[c00000000d05ba30] [0000000000000800] 0x800 (unreliable)
[c00000000d05bab0] [c008000001b0a930] do_reset.isra.40+0x224/0x634 [ibmvnic]
[c00000000d05bb80] [c008000001b08574] __ibmvnic_reset+0x17c/0x3c0 [ibmvnic]
[c00000000d05bc50] [c00000000018d9ac] process_one_work+0x2cc/0x800
[c00000000d05bd20] [c00000000018df58] worker_thread+0x78/0x520
[c00000000d05bdb0] [c00000000019a934] kthread+0x1c4/0x1d0
[c00000000d05be20] [c00000000000d5d0] ret_from_kernel_thread+0x5c/0x6c
Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
adapter->tx_scrq and adapter->rx_scrq could be NULL if the previous reset
did not complete after freeing sub crqs. Check for NULL before
dereferencing them.
Snippet of call trace:
ibmvnic 30000006 env6: Releasing sub-CRQ
ibmvnic 30000006 env6: Releasing CRQ
...
ibmvnic 30000006 env6: Got Control IP offload Response
ibmvnic 30000006 env6: Re-setting tx_scrq[0]
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc008000003dea7cc
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: rpadlpar_io rpaphp xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables xsk_diag tcp_diag udp_diag raw_diag inet_diag unix_diag af_packet_diag netlink_diag tun bridge stp llc rfkill sunrpc pseries_rng xts vmx_crypto uio_pdrv_genirq uio binfmt_misc ip_tables xfs libcrc32c sd_mod t10_pi sg ibmvscsi ibmvnic ibmveth scsi_transport_srp dm_mirror dm_region_hash dm_log dm_mod
CPU: 80 PID: 1856 Comm: kworker/80:2 Tainted: G W 5.8.0+ #4
Workqueue: events __ibmvnic_reset [ibmvnic]
NIP: c008000003dea7cc LR: c008000003dea7bc CTR: 0000000000000000
REGS: c0000007ef7db860 TRAP: 0380 Tainted: G W (5.8.0+)
MSR: 800000000280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 28002422 XER: 0000000d
CFAR: c000000000bd9520 IRQMASK: 0
GPR00: c008000003dea7bc c0000007ef7dbaf0 c008000003df7400 c0000007fa26ec00
GPR04: c0000007fcd0d008 c0000007fcd96350 0000000000000027 c0000007fcd0d010
GPR08: 0000000000000023 0000000000000000 0000000000000000 0000000000000000
GPR12: 0000000000002000 c00000001ec18e00 c0000000001982f8 c0000007bad6e840
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 fffffffffffffef7
GPR24: 0000000000000402 c0000007fa26f3a8 0000000000000003 c00000016f8ec048
GPR28: 0000000000000000 0000000000000000 0000000000000000 c0000007fa26ec00
NIP [c008000003dea7cc] ibmvnic_reset_init+0x15c/0x258 [ibmvnic]
LR [c008000003dea7bc] ibmvnic_reset_init+0x14c/0x258 [ibmvnic]
Call Trace:
[c0000007ef7dbaf0] [c008000003dea7bc] ibmvnic_reset_init+0x14c/0x258 [ibmvnic] (unreliable)
[c0000007ef7dbb80] [c008000003de8860] __ibmvnic_reset+0x408/0x970 [ibmvnic]
[c0000007ef7dbc50] [c00000000018b7cc] process_one_work+0x2cc/0x800
[c0000007ef7dbd20] [c00000000018bd78] worker_thread+0x78/0x520
[c0000007ef7dbdb0] [c0000000001984c4] kthread+0x1d4/0x1e0
[c0000007ef7dbe20] [c00000000000cea8] ret_from_kernel_thread+0x5c/0x74
Fixes: 57a49436f4e8 ("ibmvnic: Reset sub-crqs during driver reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver's ISR sends a 'software interrupt' event to the probe()
thread using the following method:
- probe(): write 0 to flag, enable s/w interrupt
- probe(): poll on flag, relax using usleep_range()
- ISR : write 1 to flag
Replace with wake_up() / wait_event_timeout(). Besides being easier
to get right, this abstraction has better timing and memory
consistency properties.
Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # lan7430
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201123191529.14908-2-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For no apparent reason, this function reads the INT_STS register, and
checks if the software interrupt bit is set. These things have already
been carried out by this function's only caller.
Clean up by removing the redundant code.
Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # lan7430
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201123191529.14908-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
