summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2021-07-28net/mlx5e: RX, Avoid possible data corruption when relaxed ordering and LRO ↵Tariq Toukan1-1/+10
combined When HW aggregates packets for an LRO session, it writes the payload of two consecutive packets of a flow contiguously, so that they usually share a cacheline. The first byte of a packet's payload is written immediately after the last byte of the preceding packet. In this flow, there are two consecutive write requests to the shared cacheline: 1. Regular write for the earlier packet. 2. Read-modify-write for the following packet. In case of relaxed-ordering on, these two writes might be re-ordered. Using the end padding optimization (to avoid partial write for the last cacheline of a packet) becomes problematic if the two writes occur out-of-order, as the padding would overwrite payload that belongs to the following packet, causing data corruption. Avoid this by disabling the end padding optimization when both LRO and relaxed-ordering are enabled. Fixes: 17347d5430c4 ("net/mlx5e: Add support for PCI relaxed ordering") Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-07-28net/mlx5: E-Switch, handle devcom events only for ports on the same deviceRoi Dayan2-4/+4
This is the same check as LAG mode checks if to enable lag. This will fix adding peer miss rules if lag is not supported and even an incorrect rules in socket direct mode. Also fix the incorrect comment on mlx5_get_next_phys_dev() as flow #1 doesn't exists. Fixes: ac004b832128 ("net/mlx5e: E-Switch, Add peer miss rules") Signed-off-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-07-28net/mlx5: E-Switch, Set destination vport vhca id only when merged eswitch ↵Maor Dickman1-3/+4
is supported Destination vport vhca id is valid flag is set only merged eswitch isn't supported. Change destination vport vhca id value to be set also only when merged eswitch is supported. Fixes: e4ad91f23f10 ("net/mlx5e: Split offloaded eswitch TC rules for port mirroring") Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-07-28net/mlx5e: Disable Rx ntuple offload for uplink representorMaor Dickman1-9/+20
Rx ntuple offload is not supported in switchdev mode. Tryng to enable it cause kernel panic. BUG: kernel NULL pointer dereference, address: 0000000000000008 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 80000001065a5067 P4D 80000001065a5067 PUD 106594067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 7 PID: 1089 Comm: ethtool Not tainted 5.13.0-rc7_for_upstream_min_debug_2021_06_23_16_44 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:mlx5e_arfs_enable+0x70/0xd0 [mlx5_core] Code: 44 24 10 00 00 00 00 48 c7 44 24 18 00 00 00 00 49 63 c4 48 89 e2 44 89 e6 48 69 c0 20 08 00 00 48 89 ef 48 03 85 68 ac 00 00 <48> 8b 40 08 48 89 44 24 08 e8 d2 aa fd ff 48 83 05 82 96 18 00 01 RSP: 0018:ffff8881047679e0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000004000000000 RCX: 0000004000000000 RDX: ffff8881047679e0 RSI: 0000000000000000 RDI: ffff888115100880 RBP: ffff888115100880 R08: ffffffffa00f6cb0 R09: ffff888104767a18 R10: ffff8881151000a0 R11: ffff888109479540 R12: 0000000000000000 R13: ffff888104767bb8 R14: ffff888115100000 R15: ffff8881151000a0 FS: 00007f41a64ab740(0000) GS:ffff8882f5dc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 0000000104cbc005 CR4: 0000000000370ea0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: set_feature_arfs+0x1e/0x40 [mlx5_core] mlx5e_handle_feature+0x43/0xa0 [mlx5_core] mlx5e_set_features+0x139/0x1b0 [mlx5_core] __netdev_update_features+0x2b3/0xaf0 ethnl_set_features+0x176/0x3a0 ? __nla_parse+0x22/0x30 genl_family_rcv_msg_doit+0xe2/0x140 genl_rcv_msg+0xde/0x1d0 ? features_reply_size+0xe0/0xe0 ? genl_get_cmd+0xd0/0xd0 netlink_rcv_skb+0x4e/0xf0 genl_rcv+0x24/0x40 netlink_unicast+0x1f6/0x2b0 netlink_sendmsg+0x225/0x450 sock_sendmsg+0x33/0x40 __sys_sendto+0xd4/0x120 ? __sys_recvmsg+0x4e/0x90 ? exc_page_fault+0x219/0x740 __x64_sys_sendto+0x25/0x30 do_syscall_64+0x3f/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f41a65b0cba Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 76 c3 0f 1f 44 00 00 55 48 83 ec 30 44 89 4c RSP: 002b:00007ffd8d688358 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00000000010f42a0 RCX: 00007f41a65b0cba RDX: 0000000000000058 RSI: 00000000010f43b0 RDI: 0000000000000003 RBP: 000000000047ae60 R08: 00007f41a667c000 R09: 000000000000000c R10: 0000000000000000 R11: 0000000000000246 R12: 00000000010f4340 R13: 00000000010f4350 R14: 00007ffd8d688400 R15: 00000000010f42a0 Modules linked in: mlx5_vdpa vhost_iotlb vdpa xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 br_netfilter rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad ib_ipoib rdma_cm iw_cm ib_cm mlx5_ib ib_uverbs ib_core overlay mlx5_core ptp pps_core fuse CR2: 0000000000000008 ---[ end trace c66523f2aba94b43 ]--- Fixes: 7a9fb35e8c3a ("net/mlx5e: Do not reload ethernet ports when changing eswitch mode") Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-07-28net/mlx5: Fix flow table chainingMaor Gottlieb1-4/+6
Fix a bug when flow table is created in priority that already has other flow tables as shown in the below diagram. If the new flow table (FT-B) has the lowest level in the priority, we need to connect the flow tables from the previous priority (p0) to this new table. In addition when this flow table is destroyed (FT-B), we need to connect the flow tables from the previous priority (p0) to the next level flow table (FT-C) in the same priority of the destroyed table (if exists). --------- |root_ns| --------- | -------------------------------- | | | ---------- ---------- --------- |p(prio)-x| | p-y | | p-n | ---------- ---------- --------- | | ---------------- ------------------ |ns(e.g bypass)| |ns(e.g. kernel) | ---------------- ------------------ | | | ------- ------ ---- | p0 | | p1 | |p2| ------- ------ ---- | | \ -------- ------- ------ | FT-A | |FT-B | |FT-C| -------- ------- ------ Fixes: f90edfd279f3 ("net/mlx5_core: Connect flow tables") Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-07-28net: ipa: don't suspend endpoints if setup not completeAlex Elder1-8/+11
Until we complete the setup stage of initialization, GSI is not initialized and therefore endpoints aren't usable. So avoid suspending endpoints during system suspend unless setup is complete. Clear the setup_complete flag at the top of ipa_teardown() to reflect the fact that things are no longer in setup state. Get rid of a misplaced (and superfluous) comment. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-28net: ipa: add a clock reference for netdev operationsAlex Elder1-1/+8
The IPA network device can be opened at any time, and an opened network device can be stopped any time. Both of these callback functions require access to the hardware, and therefore they need the IPA clock to be operational. Take an IPA clock reference in both the ->open and ->stop callback functions, dropping the reference when they are done accessing hardware. The ->start_xmit callback requires a little different handling, and that will be added separately. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-28net: ipa: add clock reference for remoteproc SSRAlex Elder1-0/+5
The remoteproc SSR callback function for the modem requires hardware access when handling a modem crash or shutdown. Take and later release an IPA clock reference in ipa_modem_crashed(), to ensure the hardware is operational. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-28net: ipa: get another clock for ipa_setup()Alex Elder1-0/+5
Two places call ipa_setup(). The first, ipa_probe(), holds an IPA clock reference when calling ipa_setup() (if the AP is responsible for IPA firmware loading). But if the modem is loading IPA firmware, ipa_smp2p_modem_setup_ready_isr() calls ipa_setup() after the modem has signaled the hardware is ready. This can happen at any time, and there is no guarantee the hardware is active. Have ipa_smp2p_modem_setup() take an IPA clock reference before it calls ipa_setup(), and release it once setup is complete. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-28net: ipa: get clock in ipa_probe()Alex Elder1-3/+15
Any entry point that leads to IPA hardware access must ensure the hardware is operational (clocked). Currently we ensure this by taking an extra clock reference during setup that is not released until we receive a system suspend request. But this extra reference will soon go away. When the platform driver ->probe function is called, we first need hardware access in ipa_config(). Although ipa_config() takes an IPA clock reference, it the special reference taken to prevent suspending the hardware. Have ipa_probe() take a reference before calling ipa_config(), so that the "no-suspend" reference can eventually go away. Drop this reference before ipa_probe() returns. Similarly, the driver ->remove function can be called at any time. Take an IPA clock reference at the beginning of that function, and drop it again after the deconfig stage has completed (at which point hardware access is no longer needed). Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27net: ipa: kill ipa_interrupt_process_all()Alex Elder1-13/+5
Now that ipa_isr_thread() is a simple wrapper that gets a clock reference around ipa_interrupt_process_all(), get rid of the called function and just open-code it in ipa_isr_thread(). Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27net: ipa: get rid of some unneeded IPA interrupt codeAlex Elder1-16/+1
The pending IPA interrupts are checked by ipa_isr_thread(), and interrupts are processed only if an enabled interrupt has a condition pending. But ipa_interrupt_process_all() now makes the same check, so the one in ipa_isr_thread() can just be skipped. Also in ipa_isr_thread(), any interrupt conditions pending which are not enabled are cleared. Here too, ipa_interrupt_process_all() now clears such excess interrupt conditions, so ipa_isr_thread() doesn't have to. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27net: ipa: clear disabled IPA interrupt conditionsAlex Elder1-3/+14
We ignore any IPA interrupt that has no handler. If any interrupt conditions without a handler exist when an IPA interrupt occurs, clear those conditions. Add a debug message to report which ones are being cleared. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27net: ipa: make IPA interrupt handler threaded onlyAlex Elder1-18/+11
When the IPA interrupt handler runs, the IPA core clock must already be operational, and the interconnect providing access by the AP to IPA config space must be enabled too. Currently we ensure this by taking a top-level "stay awake" IPA clock reference, but that will soon go away. In preparation for that, move all handling for the IPA IRQ into the thread function. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27net: hns3: change the method of obtaining default ptp cycleYufeng Mo2-9/+37
The ptp cycle is related to the hardware, so it may cause compatibility issues if a fixed value is used in driver. Therefore, the method of obtaining this value is changed to read from the register rather than use a fixed value in driver. Fixes: 0bf5eb788512 ("net: hns3: add support for PTP") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27ionic: add function tag to debug stringShannon Nelson1-2/+2
Prefix the log output with the function string as in other debug messages. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27ionic: enable rxhash only with multiple queuesShannon Nelson1-1/+3
If there's only one queue, there is no need to enable the rxhashing. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27ionic: block some ethtool operations when fw in resetShannon Nelson1-0/+21
There are a few things that we can't safely do when the fw is resetting, as the driver may be in the middle of rebuilding queue structures. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27ionic: remove unneeded comp union fieldsShannon Nelson1-2/+0
We don't use these fields, so remove them from the definition. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27ionic: increment num-vfs before configureShannon Nelson1-1/+1
Add the new VF to our internal count before we start configuring it. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27ionic: use fewer inits on the buf_info structShannon Nelson1-16/+11
Based on Alex's review notes on [1], we don't need to write to the buf_info elements as often, and can tighten up how they are used. Also, use prefetchw() to warm up the page struct for a later get_page(). [1] https://lore.kernel.org/netdev/CAKgT0UfyjoAN7LTnq0NMZfXRv4v7iTCPyAb9pVr3qWMhop_BVw@mail.gmail.com/ Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27ionic: init reconfig err to 0Shannon Nelson1-3/+10
Initialize err to 0 instead of ENOMEM, and specifically set err to ENOMEM in the devm_kcalloc() failure cases. Also, add an error message to the end of reconfig. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27ionic: print firmware version on identifyShannon Nelson1-0/+2
Print the version of the DSC firmware seen when we do a fresh ident check. Because the FW can be updated by the external orchestration system, this helps us track that FW has been updated on the DSC. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27ionic: monitor fw status generationShannon Nelson3-3/+31
The top 4 bits of the fw_status in dev_info_regs is reserved for the status generation. This generation number is an arbitrary value defined when firmware starts up. If the FW is killed/crashed/stopped and then restarted, it will create a different generation number. With this mechanism, the host driver can detect that the FW has crashed and restarted, and the driver can then take steps to re-initialize its connection. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27ionic: minimize resources when under kdumpShannon Nelson1-2/+19
When running in a small kdump kernel, we can play nice and minimize our resource use to help make sure that kdump is successful in its mission. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27net: bonding: move ioctl handling to private ndo operationArnd Bergmann1-1/+1
All other user triggered operations are gone from ndo_ioctl, so move the SIOCBOND family into a custom operation as well. The .ndo_ioctl() helper is no longer called by the dev_ioctl.c code now, but there are still a few definitions in obsolete wireless drivers as well as the appletalk and ieee802154 layers to call SIOCSIFADDR/SIOCGIFADDR helpers from inside the kernel. Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27net: split out ndo_siowandev ioctlArnd Bergmann22-229/+165
In order to further reduce the scope of ndo_do_ioctl(), move out the SIOCWANDEV handling into a new network device operation function. Adjust the prototype to only pass the if_settings sub-structure in place of the ifreq, and remove the redundant 'cmd' argument in the process. Cc: Krzysztof Halasa <khc@pm.waw.pl> Cc: "Jan \"Yenya\" Kasprzak" <kas@fi.muni.cz> Cc: Kevin Curtis <kevin.curtis@farsite.co.uk> Cc: Zhao Qiang <qiang.zhao@nxp.com> Cc: Martin Schiller <ms@dev.tdt.de> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: linux-x25@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27dev_ioctl: split out ndo_eth_ioctlArnd Bergmann160-190/+206
Most users of ndo_do_ioctl are ethernet drivers that implement the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP. Separate these from the few drivers that use ndo_do_ioctl to implement SIOCBOND, SIOCBR and SIOCWANDEV commands. This is a purely cosmetic change intended to help readers find their way through the implementation. Cc: Doug Ledford <dledford@redhat.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Vladimir Oltean <olteanv@gmail.com> Cc: Leon Romanovsky <leon@kernel.org> Cc: linux-rdma@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27wan: cosa: remove dead cosa_net_ioctl() functionArnd Bergmann1-14/+1
The ndo_do_ioctl callback is never called with the COSAIO* commands, so this is never used. Call the hdlc_ioctl function directly instead. Any user space code that relied on this function working as intended has never worked in a mainline kernel since before linux-1.0. Cc: "Jan \"Yenya\" Kasprzak" <kas@fi.muni.cz> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27wan: use ndo_siocdevprivateArnd Bergmann8-56/+117
The wan drivers each support some custom SIOCDEVPRIVATE ioctls, plus the common SIOCWANDEV command. Split these so the ioctl callback only deals with SIOCWANDEV and the rest is handled by ndo_siocdevprivate. It might make sense to also split out SIOCWANDEV into a separate callback in order to eventually remove ndo_do_ioctl entirely. Cc: Krzysztof Halasa <khc@pm.waw.pl> Cc: Kevin Curtis <kevin.curtis@farsite.co.uk> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27ppp: use ndo_siocdevprivateArnd Bergmann1-3/+3
ppp has a custom statistics interface using SIOCDEVPRIVATE ioctl commands that works correctly in compat mode. Convert it to use ndo_siocdevprivate as a cleanup. Cc: Paul Mackerras <paulus@samba.org> Cc: linux-ppp@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27sb1000: use ndo_siocdevprivateArnd Bergmann1-9/+11
The private sb1000 ioctl commands all work correctly in compat mode. Change the to ndo_siocdevprivate as a cleanup. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27hippi: use ndo_siocdevprivateArnd Bergmann2-6/+8
The rr_ioctl uses private ioctl commands that correctly pass all data through ifr_data, which works fine in compat mode. Change it to use ndo_siocdevprivate as a cleanup. Cc: Jes Sorensen <jes@trained-monkey.org> Cc: linux-hippi@sunsite.dk Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27airo: use ndo_siocdevprivateArnd Bergmann1-7/+8
The airo driver overloads SIOCDEVPRIVATE ioctls with another set based on SIOCIWFIRSTPRIV. Only the first ones actually work (also in compat mode) as the others do not get passed down any more. Change it over to ndo_siocdevprivate for clarification. Cc: Kalle Valo <kvalo@codeaurora.org> Cc: linux-wireless@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27hamradio: use ndo_siocdevprivateArnd Bergmann9-60/+64
hamradio uses a set of private ioctls that do seem to work correctly in compat mode, as they only rely on the ifr_data pointer. Move them over to the ndo_siocdevprivate callback as a cleanup. Cc: Thomas Sailer <t.sailer@alumni.ethz.ch> Cc: Joerg Reuter <jreuter@yaina.de> Cc: Jean-Paul Roubelat <jpr@f6fbb.org> Cc: linux-hams@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27cxgb3: use ndo_siocdevprivateArnd Bergmann1-4/+8
cxgb3 has a private multiplexor that works correctly in compat mode, split out the siocdevprivate callback from do_ioctl for simplification. Cc: Raju Rangoju <rajur@chelsio.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27slip/plip: use ndo_siocdevprivateArnd Bergmann2-7/+18
slip and plip both use a couple of SIOCDEVPRIVATE ioctl commands that overload the ifreq layout in a way that is incompatible with compat mode. Convert to use ndo_siocdevprivate to allow passing the data this way, but return an error in compat mode anyway because the private structure is still incompatible. This could be fixed as well to make compat work properly. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27net: usb: use ndo_siocdevprivateArnd Bergmann2-4/+6
The pegasus and rtl8150 drivers use SIOCDEVPRIVATE ioctls to access their MII registers, in place of the normal commands. This is broken for all compat ioctls today. Change to ndo_siocdevprivate to fix it. Cc: Petko Manolov <petkan@nucleusys.com> Cc: linux-usb@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27fddi: use ndo_siocdevprivateArnd Bergmann1-7/+12
The skfddi driver has a private ioctl and passes the data correctly through ifr_data, but the use of a pointer in s_skfp_ioctl is broken in compat mode. Change the driver to use ndo_siocdevprivate and disallow calling it in compat mode until a conversion handler is added. Cc: "Maciej W. Rozycki" <macro@orcam.me.uk> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27eql: use ndo_siocdevprivateArnd Bergmann1-9/+15
The private ioctls in eql pass the arguments correctly through ifr_data, but the slaving_request_t and slave_config_t structures are incompatible with compat mode and need special conversion code in the driver. Convert to siocdevprivate for now, and return an error when called in compat mode. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27tehuti: use ndo_siocdevprivateArnd Bergmann1-13/+5
Tehuti only implements private ioctl commands, and implements them by overriding the ifreq layout, which is broken in compat mode. Move it to the ndo_siocdevprivate callback in order to fix this. Cc: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27hamachi: use ndo_siocdevprivateArnd Bergmann1-25/+38
hamachi has one command that overloads the ifreq argument and requires a conversion to ndo_siocdevprivate in order to make compat mode work, so split it from ndo_ioctl. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27appletalk: use ndo_siocdevprivateArnd Bergmann1-6/+10
appletalk has three SIOCDEVPRIVATE ioctl commands that are broken in compat mode because the passed structure contains a pointer. Change it over to ndo_siocdevprivate for consistency and make it return an error when called in compat mode. This could be fixed if there are still users. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27bonding: use siocdevprivateArnd Bergmann1-6/+24
The bonding driver supports two command codes for each operation: one in the SIOCDEVPRIVATE range and another one with the same definition but a unique command code. Only the second set currently works in compat mode, as the ifr_data expansion overwrites part of the ifr_slave field. Move the private ones into ndo_siocdevprivate and change the implementation to call the other function. This makes both version work correctly. Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27tulip: use ndo_siocdevprivateArnd Bergmann1-3/+8
The tulip driver has a debugging method over ioctl built-in, but it does not actually check the command type, which may end up leading to random behavior when trying to run other ioctls on it. Change the driver to use ndo_siocdevprivate and limit the execution further to the first private command code. If anyone still has tools to run these debugging commands, they might have to be patched for it if they pass different ioctl command. The function has existed in this form since the driver was merged in Linux-1.1.86. Cc: linux-parisc@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27phonet: use siocdevprivateArnd Bergmann1-2/+3
phonet has a single private ioctl that is broken in compat mode on big-endian machines today because the data returned from it is never copied back to user space. Move it over to the ndo_siocdevprivate callback, which also fixes the compat issue. Cc: Remi Denis-Courmont <courmisch@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Rémi Denis-Courmont <courmisch@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27hostap: use ndo_siocdevprivateArnd Bergmann3-7/+29
hostap has a combination of iwpriv ioctls that do not work at all, and two SIOCDEVPRIVATE commands that work natively but lack a compat conversion handler. For the moment, move them over to the new ndo_siocdevprivate interface and return an error for compat mode. Cc: Jouni Malinen <j@w1.fi> Cc: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27net: qed: remove unneeded return variablesJason Wang1-4/+2
Some return variables are never changed until function returned. These variables are unneeded for their functions. Therefore, the unneeded return variables can be removed safely by returning their initial values. Signed-off-by: Jason Wang <wangborong@cdjrlc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27octeontx2-af: Do NIX_RX_SW_SYNC twiceSunil Goutham1-2/+13
NIX_RX_SW_SYNC ensures all existing transactions are finished and pkts are written to LLC/DRAM, queues should be teared down after successful SW_SYNC. Due to a HW errata, in some rare scenarios an existing transaction might end after SW_SYNC operation. To ensure operation is fully done, do the SW_SYNC twice. Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27tty: drop put_tty_driverJiri Slaby1-2/+2
put_tty_driver() is an alias for tty_driver_kref_put(). There is no need for two exported identical functions, therefore switch all users of old put_tty_driver() to new tty_driver_kref_put() and remove the former for good. Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Jeff Dike <jdike@addtoit.com> Cc: Richard Weinberger <richard@nod.at> Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com> Cc: Chris Zankel <chris@zankel.net> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com> Cc: Jens Taprogge <jens.taprogge@taprogge.org> Cc: Karsten Keil <isdn@linux-pingi.de> Cc: Scott Branden <scott.branden@broadcom.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: David Lin <dtwlin@gmail.com> Cc: Johan Hovold <johan@kernel.org> Cc: Alex Elder <elder@kernel.org> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: David Sterba <dsterba@suse.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Oliver Neukum <oneukum@suse.com> Cc: Felipe Balbi <balbi@kernel.org> Cc: Mathias Nyman <mathias.nyman@intel.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Acked-by: Alex Elder <elder@linaro.org> Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: David Sterba <dsterba@suse.com> Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20210723074317.32690-8-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-10-02 06:08:26 +0300