summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2021-10-13net: mscc: ocelot: avoid overflowing the PTP timestamp FIFOVladimir Oltean2-8/+35
PTP packets with 2-step TX timestamp requests are matched to packets based on the egress port number and a 6-bit timestamp identifier. All PTP timestamps are held in a common FIFO that is 128 entry deep. This patch ensures that back-to-back timestamping requests cannot exceed the hardware FIFO capacity. If that happens, simply send the packets without requesting a TX timestamp to be taken (in the case of felix, since the DSA API has a void return code in ds->ops->port_txtstamp) or drop them (in the case of ocelot). I've moved the ts_id_lock from a per-port basis to a per-switch basis, because we need separate accounting for both numbers of PTP frames in flight. And since we need locking to inc/dec the per-switch counter, that also offers protection for the per-port counter and hence there is no reason to have a per-port counter anymore. Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-13net: mscc: ocelot: make use of all 63 PTP timestamp identifiersVladimir Oltean1-1/+3
At present, there is a problem when user space bombards a port with PTP event frames which have TX timestamping requests (or when a tc-taprio offload is installed on a port, which delays the TX timestamps by a significant amount of time). The driver will happily roll over the 2-bit timestamp ID and this will cause incorrect matches between an skb and the TX timestamp collected from the FIFO. The Ocelot switches have a 6-bit PTP timestamp identifier, and the value 63 is reserved, so that leaves identifiers 0-62 to be used. The timestamp identifiers are selected by the REW_OP packet field, and are actually shared between CPU-injected frames and frames which match a VCAP IS2 rule that modifies the REW_OP. The hardware supports partitioning between the two uses of the REW_OP field through the PTP_ID_LOW and PTP_ID_HIGH registers, and by default reserves the PTP IDs 0-3 for CPU-injected traffic and the rest for VCAP IS2. The driver does not use VCAP IS2 to set REW_OP for 2-step timestamping, and it also writes 0xffffffff to both PTP_ID_HIGH and PTP_ID_LOW in ocelot_init_timestamp() which makes all timestamp identifiers available to CPU injection. Therefore, we can make use of all 63 timestamp identifiers, which should allow more timestampable packets to be in flight on each port. This is only part of the solution, more issues will be addressed in future changes. Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-13net: dsa: sja1105: break dependency between dsa_port_is_sja1105 and switch ↵Vladimir Oltean1-2/+1
driver It's nice to be able to test a tagging protocol with dsa_loop, but not at the cost of losing the ability of building the tagging protocol and switch driver as modules, because as things stand, there is a circular dependency between the two. Tagging protocol drivers cannot depend on switch drivers, that is a hard fact. The reasoning behind the blamed patch was that accessing dp->priv should first make sure that the structure behind that pointer is what we really think it is. Currently the "sja1105" and "sja1110" tagging protocols only operate with the sja1105 switch driver, just like any other tagging protocol and switch combination. The only way to mix and match them is by modifying the code, and this applies to dsa_loop as well (by default that uses DSA_TAG_PROTO_NONE). So while in principle there is an issue, in practice there isn't one. Until we extend dsa_loop to allow user space configuration, treat the problem as a non-issue and just say that DSA ports found by tag_sja1105 are always sja1105 ports, which is in fact true. But keep the dsa_port_is_sja1105 function so that it's easy to patch it during testing, and rely on dead code elimination. Fixes: 994d2cbb08ca ("net: dsa: tag_sja1105: be dsa_loop-safe") Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/ Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-13net: dsa: move sja1110_process_meta_tstamp inside the tagging protocol driverVladimir Oltean2-58/+6
The problem is that DSA tagging protocols really must not depend on the switch driver, because this creates a circular dependency at insmod time, and the switch driver will effectively not load when the tagging protocol driver is missing. The code was structured in the way it was for a reason, though. The DSA driver-facing API for PTP timestamping relies on the assumption that two-step TX timestamps are provided by the hardware in an out-of-band manner, typically by raising an interrupt and making that timestamp available inside some sort of FIFO which is to be accessed over SPI/MDIO/etc. So the API puts .port_txtstamp into dsa_switch_ops, because it is expected that the switch driver needs to save some state (like put the skb into a queue until its TX timestamp arrives). On SJA1110, TX timestamps are provided by the switch as Ethernet packets, so this makes them be received and processed by the tagging protocol driver. This in itself is great, because the timestamps are full 64-bit and do not require reconstruction, and since Ethernet is the fastest I/O method available to/from the switch, PTP timestamps arrive very quickly, no matter how bottlenecked the SPI connection is, because SPI interaction is not needed at all. DSA's code structure and strict isolation between the tagging protocol driver and the switch driver break the natural code organization. When the tagging protocol driver receives a packet which is classified as a metadata packet containing timestamps, it passes those timestamps one by one to the switch driver, which then proceeds to compare them based on the recorded timestamp ID that was generated in .port_txtstamp. The communication between the tagging protocol and the switch driver is done through a method exported by the switch driver, sja1110_process_meta_tstamp. To satisfy build requirements, we force a dependency to build the tagging protocol driver as a module when the switch driver is a module. However, as explained in the first paragraph, that causes the circular dependency. To solve this, move the skb queue from struct sja1105_private :: struct sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data. The latter is a data structure for which hacks have already been put into place to be able to create persistent storage per switch that is accessible from the tagging protocol driver (see sja1105_setup_ports). With the skb queue directly accessible from the tagging protocol driver, we can now move sja1110_process_meta_tstamp into the tagging driver itself, and avoid exporting a symbol. Fixes: 566b18c8b752 ("net: dsa: sja1105: implement TX timestamping for SJA1110") Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/ Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-13nfp: flow_offload: move flow_indr_dev_register from app init to app startBaowen Zheng1-5/+14
In commit 74fc4f828769 ("net: Fix offloading indirect devices dependency on qdisc order creation"), it adds a process to trigger the callback to setup the bo callback when the driver regists a callback. In our current implement, we are not ready to run the callback when nfp call the function flow_indr_dev_register, then there will be error message as: kernel: Oops: 0000 [#1] SMP PTI kernel: CPU: 0 PID: 14119 Comm: kworker/0:0 Tainted: G kernel: Workqueue: events work_for_cpu_fn kernel: RIP: 0010:nfp_flower_indr_setup_tc_cb+0x258/0x410 kernel: RSP: 0018:ffffbc1e02c57bf8 EFLAGS: 00010286 kernel: RAX: 0000000000000000 RBX: ffff9c761fabc000 RCX: 0000000000000001 kernel: RDX: 0000000000000001 RSI: fffffffffffffff0 RDI: ffffffffc0be9ef1 kernel: RBP: ffffbc1e02c57c58 R08: ffffffffc08f33aa R09: ffff9c6db7478800 kernel: R10: 0000009c003f6e00 R11: ffffbc1e02800000 R12: ffffbc1e000d9000 kernel: R13: ffffbc1e000db428 R14: ffff9c6db7478800 R15: ffff9c761e884e80 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: fffffffffffffff0 CR3: 00000009e260a004 CR4: 00000000007706f0 kernel: DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 kernel: DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 kernel: PKRU: 55555554 kernel: Call Trace: kernel: ? flow_indr_dev_register+0xab/0x210 kernel: ? __cond_resched+0x15/0x30 kernel: ? kmem_cache_alloc_trace+0x44/0x4b0 kernel: ? nfp_flower_setup_tc+0x1d0/0x1d0 [nfp] kernel: flow_indr_dev_register+0x158/0x210 kernel: ? tcf_block_unbind+0xe0/0xe0 kernel: nfp_flower_init+0x40b/0x650 [nfp] kernel: nfp_net_pci_probe+0x25f/0x960 [nfp] kernel: ? nfp_rtsym_read_le+0x76/0x130 [nfp] kernel: nfp_pci_probe+0x6a9/0x820 [nfp] kernel: local_pci_probe+0x45/0x80 So we need to call flow_indr_dev_register in app start process instead of init stage. Fixes: 74fc4f828769 ("net: Fix offloading indirect devices dependency on qdisc order creation") Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Link: https://lore.kernel.org/r/20211012124850.13025-1-louis.peens@corigine.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-12net/mlx5e: Fix division by 0 in mlx5e_select_queue for representorsMaxim Mikityanskiy1-0/+5
Commit 846d6da1fcdb ("net/mlx5e: Fix division by 0 in mlx5e_select_queue") makes mlx5e_build_nic_params assign a non-zero initial value to priv->num_tc_x_num_ch, so that mlx5e_select_queue doesn't fail with division by 0 if called before the first activation of channels. However, the initialization flow of representors doesn't call mlx5e_build_nic_params, so this bug can still happen with representors. This commit fixes the bug by adding the missing assignment to mlx5e_build_rep_params. Fixes: 846d6da1fcdb ("net/mlx5e: Fix division by 0 in mlx5e_select_queue") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-12net/mlx5e: Mutually exclude RX-FCS and RX-port-timestampAya Levin1-5/+52
Due to current HW arch limitations, RX-FCS (scattering FCS frame field to software) and RX-port-timestamp (improved timestamp accuracy on the receive side) can't work together. RX-port-timestamp is not controlled by the user and it is enabled by default when supported by the HW/FW. This patch sets RX-port-timestamp opposite to RX-FCS configuration. Fixes: 102722fc6832 ("net/mlx5e: Add support for RXFCS feature flag") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-12net/mlx5e: Switchdev representors are not vlan challengedSaeed Mahameed1-1/+0
Before this patch, mlx5 representors advertised the NETIF_F_VLAN_CHALLENGED bit, this could lead to missing features when using reps with vxlan/bridge and maybe other virtual interfaces, when such interfaces inherit this bit and block vlan usage in their topology. Example: $ip link add dev bridge type bridge # add representor interface to the bridge $ip link set dev pf0hpf master $ip link add link bridge name vlan10 type vlan id 10 protocol 802.1q Error: 8021q: VLANs not supported on device. Reps are perfectly capable of handling vlan traffic, although they don't implement vlan_{add,kill}_vid ndos, hence, remove NETIF_F_VLAN_CHALLENGED advertisement. Fixes: cb67b832921c ("net/mlx5e: Introduce SRIOV VF representors") Reported-by: Roopa Prabhu <roopa@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com>
2021-10-12net/mlx5e: Fix memory leak in mlx5_core_destroy_cq() error pathValentine Fatiev1-4/+3
Prior to this patch in case mlx5_core_destroy_cq() failed it returns without completing all destroy operations and that leads to memory leak. Instead, complete the destroy flow before return error. Also move mlx5_debug_cq_remove() to the beginning of mlx5_core_destroy_cq() to be symmetrical with mlx5_core_create_cq(). kmemleak complains on: unreferenced object 0xc000000038625100 (size 64): comm "ethtool", pid 28301, jiffies 4298062946 (age 785.380s) hex dump (first 32 bytes): 60 01 48 94 00 00 00 c0 b8 05 34 c3 00 00 00 c0 `.H.......4..... 02 00 00 00 00 00 00 00 00 db 7d c1 00 00 00 c0 ..........}..... backtrace: [<000000009e8643cb>] add_res_tree+0xd0/0x270 [mlx5_core] [<00000000e7cb8e6c>] mlx5_debug_cq_add+0x5c/0xc0 [mlx5_core] [<000000002a12918f>] mlx5_core_create_cq+0x1d0/0x2d0 [mlx5_core] [<00000000cef0a696>] mlx5e_create_cq+0x210/0x3f0 [mlx5_core] [<000000009c642c26>] mlx5e_open_cq+0xb4/0x130 [mlx5_core] [<0000000058dfa578>] mlx5e_ptp_open+0x7f4/0xe10 [mlx5_core] [<0000000081839561>] mlx5e_open_channels+0x9cc/0x13e0 [mlx5_core] [<0000000009cf05d4>] mlx5e_switch_priv_channels+0xa4/0x230 [mlx5_core] [<0000000042bbedd8>] mlx5e_safe_switch_params+0x14c/0x300 [mlx5_core] [<0000000004bc9db8>] set_pflag_tx_port_ts+0x9c/0x160 [mlx5_core] [<00000000a0553443>] mlx5e_set_priv_flags+0xd0/0x1b0 [mlx5_core] [<00000000a8f3d84b>] ethnl_set_privflags+0x234/0x2d0 [<00000000fd27f27c>] genl_family_rcv_msg_doit+0x108/0x1d0 [<00000000f495e2bb>] genl_family_rcv_msg+0xe4/0x1f0 [<00000000646c5c2c>] genl_rcv_msg+0x78/0x120 [<00000000d53e384e>] netlink_rcv_skb+0x74/0x1a0 Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Valentine Fatiev <valentinef@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-12net/mlx5e: Allow only complete TXQs partition in MQPRIO channel modeTariq Toukan1-2/+2
Do not allow configurations of MQPRIO channel mode that do not fully define and utilize the channels txqs. Fixes: ec60c4581bd9 ("net/mlx5e: Support MQPRIO channel mode") Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-12net/mlx5: Fix cleanup of bridge delayed workShay Drory1-4/+4
Currently, bridge cleanup is calling to cancel_delayed_work(). When this function is finished, there is a chance that the delayed work is still running. Also, the delayed work is queueing itself. As a result, we might execute the delayed work after the bridge cleanup have finished and hit a null-ptr oops[1]. Fix it by using cancel_delayed_work_sync(), which is waiting until the work is done and will cancel the queue work. [1] [ 8202.143043 ] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 8202.144438 ] #PF: supervisor write access in kernel mode [ 8202.145476 ] #PF: error_code(0x0002) - not-present page [ 8202.146520 ] PGD 0 P4D 0 [ 8202.147126 ] Oops: 0002 [#1] SMP NOPTI [ 8202.147899 ] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.14.0-rc6_for_upstream_min_debug_2021_08_25_16_06 #1 [ 8202.149741 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [ 8202.151908 ] RIP: 0010:_raw_spin_lock+0xc/0x20 [ 8202.156234 ] RSP: 0018:ffff88846f885ea0 EFLAGS: 00010046 [ 8202.157289 ] RAX: 0000000000000000 RBX: ffff88846f880000 RCX: 0000000000000000 [ 8202.158731 ] RDX: 0000000000000001 RSI: ffff8881004000c8 RDI: 0000000000000000 [ 8202.160177 ] RBP: ffff8881fe684978 R08: ffff888100140000 R09: ffffffff824455b8 [ 8202.161569 ] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001 [ 8202.163004 ] R13: 0000000000000012 R14: 0000000000000200 R15: ffff88812992d000 [ 8202.164018 ] FS: 0000000000000000(0000) GS:ffff88846f880000(0000) knlGS:0000000000000000 [ 8202.164960 ] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 8202.165634 ] CR2: 0000000000000000 CR3: 0000000108cac004 CR4: 0000000000370ea0 [ 8202.166450 ] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 8202.167807 ] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 8202.168852 ] Call Trace: [ 8202.169421 ] <IRQ> [ 8202.169792 ] __queue_work+0xf2/0x3d0 [ 8202.170481 ] ? queue_work_node+0x40/0x40 [ 8202.171270 ] call_timer_fn+0x2b/0x100 [ 8202.171932 ] __run_timers.part.0+0x152/0x220 [ 8202.172717 ] ? __hrtimer_run_queues+0x171/0x290 [ 8202.173526 ] ? kvm_clock_get_cycles+0xd/0x10 [ 8202.174232 ] ? ktime_get+0x35/0x90 [ 8202.174943 ] run_timer_softirq+0x26/0x50 [ 8202.175745 ] __do_softirq+0xc7/0x271 [ 8202.176373 ] irq_exit_rcu+0x93/0xb0 [ 8202.176983 ] sysvec_apic_timer_interrupt+0x72/0x90 [ 8202.177755 ] </IRQ> [ 8202.178245 ] asm_sysvec_apic_timer_interrupt+0x12/0x20 Fixes: c636a0f0f3f0 ("net/mlx5: Bridge, dynamic entry ageing") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Vlad Buslov <vladbu@nvidia.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-12ice: fix locking for Tx timestamp tracking flushJacob Keller1-8/+7
Commit 4dd0d5c33c3e ("ice: add lock around Tx timestamp tracker flush") added a lock around the Tx timestamp tracker flow which is used to cleanup any left over SKBs and prepare for device removal. This lock is problematic because it is being held around a call to ice_clear_phy_tstamp. The clear function takes a mutex to send a PHY write command to firmware. This could lead to a deadlock if the mutex actually sleeps, and causes the following warning on a kernel with preemption debugging enabled: [ 715.419426] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:573 [ 715.427900] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 3100, name: rmmod [ 715.435652] INFO: lockdep is turned off. [ 715.439591] Preemption disabled at: [ 715.439594] [<0000000000000000>] 0x0 [ 715.446678] CPU: 52 PID: 3100 Comm: rmmod Tainted: G W OE 5.15.0-rc4+ #42 bdd7ec3018e725f159ca0d372ce8c2c0e784891c [ 715.458058] Hardware name: Intel Corporation S2600STQ/S2600STQ, BIOS SE5C620.86B.02.01.0010.010620200716 01/06/2020 [ 715.468483] Call Trace: [ 715.470940] dump_stack_lvl+0x6a/0x9a [ 715.474613] ___might_sleep.cold+0x224/0x26a [ 715.478895] __mutex_lock+0xb3/0x1440 [ 715.482569] ? stack_depot_save+0x378/0x500 [ 715.486763] ? ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.494979] ? kfree+0xc1/0x520 [ 715.498128] ? mutex_lock_io_nested+0x12a0/0x12a0 [ 715.502837] ? kasan_set_free_info+0x20/0x30 [ 715.507110] ? __kasan_slab_free+0x10b/0x140 [ 715.511385] ? slab_free_freelist_hook+0xc7/0x220 [ 715.516092] ? kfree+0xc1/0x520 [ 715.519235] ? ice_deinit_lag+0x16c/0x220 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.527359] ? ice_remove+0x1cf/0x6a0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.535133] ? pci_device_remove+0xab/0x1d0 [ 715.539318] ? __device_release_driver+0x35b/0x690 [ 715.544110] ? driver_detach+0x214/0x2f0 [ 715.548035] ? bus_remove_driver+0x11d/0x2f0 [ 715.552309] ? pci_unregister_driver+0x26/0x250 [ 715.556840] ? ice_module_exit+0xc/0x2f [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.564799] ? __do_sys_delete_module.constprop.0+0x2d8/0x4e0 [ 715.570554] ? do_syscall_64+0x3b/0x90 [ 715.574303] ? entry_SYSCALL_64_after_hwframe+0x44/0xae [ 715.579529] ? start_flush_work+0x542/0x8f0 [ 715.583719] ? ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.591923] ice_sq_send_cmd+0x78/0x14c0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.599960] ? wait_for_completion_io+0x250/0x250 [ 715.604662] ? lock_acquire+0x196/0x200 [ 715.608504] ? do_raw_spin_trylock+0xa5/0x160 [ 715.612864] ice_sbq_rw_reg+0x1e6/0x2f0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.620813] ? ice_reset+0x130/0x130 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.628497] ? __debug_check_no_obj_freed+0x1e8/0x3c0 [ 715.633550] ? trace_hardirqs_on+0x1c/0x130 [ 715.637748] ice_write_phy_reg_e810+0x70/0xf0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.646220] ? do_raw_spin_trylock+0xa5/0x160 [ 715.650581] ? ice_ptp_release+0x910/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.658797] ? ice_ptp_release+0x255/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.667013] ice_clear_phy_tstamp+0x2c/0x110 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.675403] ice_ptp_release+0x408/0x910 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.683440] ice_remove+0x560/0x6a0 [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.691037] ? _raw_spin_unlock_irqrestore+0x46/0x73 [ 715.696005] pci_device_remove+0xab/0x1d0 [ 715.700018] __device_release_driver+0x35b/0x690 [ 715.704637] driver_detach+0x214/0x2f0 [ 715.708389] bus_remove_driver+0x11d/0x2f0 [ 715.712489] pci_unregister_driver+0x26/0x250 [ 715.716857] ice_module_exit+0xc/0x2f [ice 9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d] [ 715.724637] __do_sys_delete_module.constprop.0+0x2d8/0x4e0 [ 715.730210] ? free_module+0x6d0/0x6d0 [ 715.733963] ? task_work_run+0xe1/0x170 [ 715.737803] ? exit_to_user_mode_loop+0x17f/0x1d0 [ 715.742509] ? rcu_read_lock_sched_held+0x12/0x80 [ 715.747215] ? trace_hardirqs_on+0x1c/0x130 [ 715.751401] do_syscall_64+0x3b/0x90 [ 715.754981] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 715.760033] RIP: 0033:0x7f4dfe59000b [ 715.763612] Code: 73 01 c3 48 8b 0d 6d 1e 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 3d 1e 0c 00 f7 d8 64 89 01 48 [ 715.782357] RSP: 002b:00007ffe8c891708 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0 [ 715.789923] RAX: ffffffffffffffda RBX: 00005558a20468b0 RCX: 00007f4dfe59000b [ 715.797054] RDX: 000000000000000a RSI: 0000000000000800 RDI: 00005558a2046918 [ 715.804189] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 [ 715.811319] R10: 00007f4dfe603ac0 R11: 0000000000000206 R12: 00007ffe8c891940 [ 715.818455] R13: 00007ffe8c8920a3 R14: 00005558a20462a0 R15: 00005558a20468b0 Notice that this is the only case where we use the lock in this way. In the cleanup kthread and work kthread the lock is only taken around the bit accesses. This was done intentionally to avoid this kind of issue. The way the lock is used, we only protect ordering of bit sets vs bit clears. The Tx writers in the hot path don't need to be protected against the entire kthread loop. The Tx queues threads only need to ensure that they do not re-use an index that is currently in use. The cleanup loop does not need to block all new set bits, since it will re-queue itself if new timestamps are present. Fix the tracker flow so that it uses the same flow as the standard cleanup thread. In addition, ensure the in_use bitmap actually gets cleared properly. This fixes the warning and also avoids the potential deadlock that might have occurred otherwise. Fixes: 4dd0d5c33c3e ("ice: add lock around Tx timestamp tracker flush") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-12net: dsa: microchip: Added the condition for scheduling ksz_mib_read_workArun Ramadoss1-1/+3
When the ksz module is installed and removed using rmmod, kernel crashes with null pointer dereferrence error. During rmmod, ksz_switch_remove function tries to cancel the mib_read_workqueue using cancel_delayed_work_sync routine and unregister switch from dsa. During dsa_unregister_switch it calls ksz_mac_link_down, which in turn reschedules the workqueue since mib_interval is non-zero. Due to which queue executed after mib_interval and it tries to access dp->slave. But the slave is unregistered in the ksz_switch_remove function. Hence kernel crashes. To avoid this crash, before canceling the workqueue, resetted the mib_interval to 0. v1 -> v2: -Removed the if condition in ksz_mib_read_work Fixes: 469b390e1ba3 ("net: dsa: microchip: use delayed_work instead of timer + work") Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-12r8152: select CRC32 and CRYPTO/CRYPTO_HASH/CRYPTO_SHA256Vegard Nossum1-0/+4
Fix the following build/link errors by adding a dependency on CRYPTO, CRYPTO_HASH, CRYPTO_SHA256 and CRC32: ld: drivers/net/usb/r8152.o: in function `rtl8152_fw_verify_checksum': r8152.c:(.text+0x2b2a): undefined reference to `crypto_alloc_shash' ld: r8152.c:(.text+0x2bed): undefined reference to `crypto_shash_digest' ld: r8152.c:(.text+0x2c50): undefined reference to `crypto_destroy_tfm' ld: drivers/net/usb/r8152.o: in function `_rtl8152_set_rx_mode': r8152.c:(.text+0xdcb0): undefined reference to `crc32_le' Fixes: 9370f2d05a2a1 ("r8152: support request_firmware for RTL8153") Fixes: ac718b69301c7 ("net/usb: new driver for RTL8152") Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-12net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY'sMaarten Zanders1-2/+11
mv88e6xxx_port_ppu_updates() interpretes data in the PORT_STS register incorrectly for internal ports (ie no PPU). In these cases, the PHY_DETECT bit indicates link status. This results in forcing the MAC state whenever the PHY link goes down which is not intended. As a side effect, LED's configured to show link status stay lit even though the physical link is down. Add a check in mac_link_down and mac_link_up to see if it concerns an external port and only then, look at PPU status. Fixes: 5d5b231da7ac (net: dsa: mv88e6xxx: use PHY_DETECT in mac_link_up/mac_link_down) Reported-by: Maarten Zanders <m.zanders@televic.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: Maarten Zanders <maarten.zanders@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-12net: mscc: ocelot: Fix dumplicated argument in ocelotWan Jiabing2-3/+3
Fix the following coccicheck warning: drivers/net/ethernet/mscc/ocelot.c:474:duplicated argument to & or | drivers/net/ethernet/mscc/ocelot.c:476:duplicated argument to & or | drivers/net/ethernet/mscc/ocelot_net.c:1627:duplicated argument to & or | These DEV_CLOCK_CFG_MAC_TX_RST are duplicate here. Here should be DEV_CLOCK_CFG_MAC_RX_RST. Fixes: e6e12df625f2 ("net: mscc: ocelot: convert to phylink") Signed-off-by: Wan Jiabing <wanjiabing@vivo.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-09virtio-net: fix for skb_over_panic inside big modeXuan Zhuo1-1/+1
commit 126285651b7f ("Merge ra.kernel.org:/pub/scm/linux/kernel/git/netdev/net") accidentally reverted the effect of commit 1a8024239da ("virtio-net: fix for skb_over_panic inside big mode") on drivers/net/virtio_net.c As a result, users of crosvm (which is using large packet mode) are experiencing crashes with 5.14-rc1 and above that do not occur with 5.13. Crash trace: [ 61.346677] skbuff: skb_over_panic: text:ffffffff881ae2c7 len:3762 put:3762 head:ffff8a5ec8c22000 data:ffff8a5ec8c22010 tail:0xec2 end:0xec0 dev:<NULL> [ 61.369192] kernel BUG at net/core/skbuff.c:111! [ 61.372840] invalid opcode: 0000 [#1] SMP PTI [ 61.374892] CPU: 5 PID: 0 Comm: swapper/5 Not tainted 5.14.0-rc1 linux-v5.14-rc1-for-mesa-ci.tar.bz2 #1 [ 61.376450] Hardware name: ChromiumOS crosvm, BIOS 0 .. [ 61.393635] Call Trace: [ 61.394127] <IRQ> [ 61.394488] skb_put.cold+0x10/0x10 [ 61.395095] page_to_skb+0xf7/0x410 [ 61.395689] receive_buf+0x81/0x1660 [ 61.396228] ? netif_receive_skb_list_internal+0x1ad/0x2b0 [ 61.397180] ? napi_gro_flush+0x97/0xe0 [ 61.397896] ? detach_buf_split+0x67/0x120 [ 61.398573] virtnet_poll+0x2cf/0x420 [ 61.399197] __napi_poll+0x25/0x150 [ 61.399764] net_rx_action+0x22f/0x280 [ 61.400394] __do_softirq+0xba/0x257 [ 61.401012] irq_exit_rcu+0x8e/0xb0 [ 61.401618] common_interrupt+0x7b/0xa0 [ 61.402270] </IRQ> See https://lore.kernel.org/r/5edaa2b7c2fe4abd0347b8454b2ac032b6694e2c.camel%40collabora.com for the report. Apply the original 1a8024239da ("virtio-net: fix for skb_over_panic inside big mode") again, the original logic still holds: In virtio-net's large packet mode, there is a hole in the space behind buf. hdr_padded_len - hdr_len We must take this into account when calculating tailroom. Cc: Greg KH <gregkh@linuxfoundation.org> Fixes: fb32856b16ad ("virtio-net: page_to_skb() use build_skb when there's sufficient tailroom") Fixes: 126285651b7f ("Merge ra.kernel.org:/pub/scm/linux/kernel/git/netdev/net") Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Reported-by: Corentin Noël <corentin.noel@collabora.com> Tested-by: Corentin Noël <corentin.noel@collabora.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-09net: phy: Do not shutdown PHYs in READY stateFlorian Fainelli1-0/+3
In case a PHY device was probed thus in the PHY_READY state, but not configured and with no network device attached yet, we should not be trying to shut it down because it has been brought back into reset by phy_device_reset() towards the end of phy_probe() and anyway we have not configured the PHY yet. Fixes: e2f016cf7751 ("net: phy: add a shutdown procedure") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-09qed: Fix missing error code in qed_slowpath_start()chongjiapeng1-0/+1
The error code is missing in this code scenario, add the error code '-EINVAL' to the return value 'rc'. Eliminate the follow smatch warning: drivers/net/ethernet/qlogic/qed/qed_main.c:1298 qed_slowpath_start() warn: missing error code 'rc'. Reported-by: Abaci Robot <abaci@linux.alibaba.com> Fixes: d51e4af5c209 ("qed: aRFS infrastructure support") Signed-off-by: chongjiapeng <jiapeng.chong@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-09ionic: don't remove netdev->dev_addr when syncing uc listShannon Nelson1-0/+4
Bridging, and possibly other upper stack gizmos, adds the lower device's netdev->dev_addr to its own uc list, and then requests it be deleted when the upper bridge device is removed. This delete request also happens with the bridging vlan_filtering is enabled and then disabled. Bonding has a similar behavior with the uc list, but since it also uses set_mac to manage netdev->dev_addr, it doesn't have the same the failure case. Because we store our netdev->dev_addr in our uc list, we need to ignore the delete request from dev_uc_sync so as to not lose the address and all hope of communicating. Note that ndo_set_mac_address is expressly changing netdev->dev_addr, so no limitation is set there. Fixes: 2a654540be10 ("ionic: Add Rx filter and rx_mode ndo support") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-09net: mana: Fix error handling in mana_create_rxq()Haiyang Zhang1-1/+3
Fix error handling in mana_create_rxq() when cq->gdma_id >= gc->max_num_cqs. Fixes: ca9c54d2d6a5 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Link: https://lore.kernel.org/r/1633698691-31721-1-git-send-email-haiyangz@microsoft.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-09net: dsa: mv88e6xxx: isolate the ATU databases of standalone and bridged portsVladimir Oltean2-13/+57
Similar to commit 6087175b7991 ("net: dsa: mt7530: use independent VLAN learning on VLAN-unaware bridges"), software forwarding between an unoffloaded LAG port (a bonding interface with an unsupported policy) and a mv88e6xxx user port directly under a bridge is broken. We adopt the same strategy, which is to make the standalone ports not find any ATU entry learned on a bridge port. Theory: the mv88e6xxx ATU is looked up by FID and MAC address. There are as many FIDs as VIDs (4096). The FID is derived from the VID when possible (the VTU maps a VID to a FID), with a fallback to the port based default FID value when not (802.1Q Mode is disabled on the port, or the classified VID isn't present in the VTU). The mv88e6xxx driver makes the following use of FIDs and VIDs: - the port's DefaultVID (to which untagged & pvid-tagged packets get classified) is 0 and is absent from the VTU, so this kind of packets is processed in FID 0, the default FID assigned by mv88e6xxx_setup_port. - every time a bridge VLAN is created, mv88e6xxx_port_vlan_join() -> mv88e6xxx_atu_new() associates a FID with that VID which increases linearly starting from 1. Like this: bridge vlan add dev lan0 vid 100 # FID 1 bridge vlan add dev lan1 vid 100 # still FID 1 bridge vlan add dev lan2 vid 1024 # FID 2 The FID allocation made by the driver is sub-optimal for the following reasons: (a) A standalone port has a DefaultPVID of 0 and a default FID of 0 too. A VLAN-unaware bridged port has a DefaultPVID of 0 and a default FID of 0 too. The difference is that the bridged ports may learn ATU entries, while the standalone port has the requirement that it must not, and must not find them either. Standalone ports must not use the same FID as ports belonging to a bridge. All standalone ports can use the same FID, since the ATU will never have an entry in that FID. (b) Multiple VLAN-unaware bridges will all use a DefaultPVID of 0 and a default FID of 0 on all their ports. The FDBs will not be isolated between these bridges. Every VLAN-unaware bridge must use the same FID on all its ports, different from the FID of other bridge ports. (c) Each bridge VLAN uses a unique FID which is useful for Independent VLAN Learning, but the same VLAN ID on multiple VLAN-aware bridges will result in the same FID being used by mv88e6xxx_atu_new(). The correct behavior is for VLAN 1 in br0 to have a different FID compared to VLAN 1 in br1. This patch cannot fix all the above. Traditionally the DSA framework did not care about this, and the reality is that DSA core involvement is needed for the aforementioned issues to be solved. The only thing we can solve here is an issue which does not require API changes, and that is issue (a), aka use a different FID for standalone ports vs ports under VLAN-unaware bridges. The first step is deciding what VID and FID to use for standalone ports, and what VID and FID for bridged ports. The 0/0 pair for standalone ports is what they used up till now, let's keep using that. For bridged ports, there are 2 cases: - VLAN-aware ports will never end up using the port default FID, because packets will always be classified to a VID in the VTU or dropped otherwise. The FID is the one associated with the VID in the VTU. - On VLAN-unaware ports, we _could_ leave their DefaultVID (pvid) at zero (just as in the case of standalone ports), and just change the port's default FID from 0 to a different number (say 1). However, Tobias points out that there is one more requirement to cater to: cross-chip bridging. The Marvell DSA header does not carry the FID in it, only the VID. So once a packet crosses a DSA link, if it has a VID of zero it will get classified to the default FID of that cascade port. Relying on a port default FID for upstream cascade ports results in contradictions: a default FID of 0 breaks ATU isolation of bridged ports on the downstream switch, a default FID of 1 breaks standalone ports on the downstream switch. So not only must standalone ports have different FIDs compared to bridged ports, they must also have different DefaultVID values. IEEE 802.1Q defines two reserved VID values: 0 and 4095. So we simply choose 4095 as the DefaultVID of ports belonging to VLAN-unaware bridges, and VID 4095 maps to FID 1. For the xmit operation to look up the same ATU database, we need to put VID 4095 in DSA tags sent to ports belonging to VLAN-unaware bridges too. All shared ports are configured to map this VID to the bridging FID, because they are members of that VLAN in the VTU. Shared ports don't need to have 802.1QMode enabled in any way, they always parse the VID from the DSA header, they don't need to look at the 802.1Q header. We install VID 4095 to the VTU in mv88e6xxx_setup_port(), with the mention that mv88e6xxx_vtu_setup() which was located right below that call was flushing the VTU so those entries wouldn't be preserved. So we need to relocate the VTU flushing prior to the port initialization during ->setup(). Also note that this is why it is safe to assume that VID 4095 will get associated with FID 1: the user ports haven't been created, so there is no avenue for the user to create a bridge VLAN which could otherwise race with the creation of another FID which would otherwise use up the non-reserved FID value of 1. [ Currently mv88e6xxx_port_vlan_join() doesn't have the option of specifying a preferred FID, it always calls mv88e6xxx_atu_new(). ] mv88e6xxx_port_db_load_purge() is the function to access the ATU for FDB/MDB entries, and it used to determine the FID to use for VLAN-unaware FDB entries (VID=0) using mv88e6xxx_port_get_fid(). But the driver only called mv88e6xxx_port_set_fid() once, during probe, so no surprises, the port FID was always 0, the call to get_fid() was redundant. As much as I would have wanted to not touch that code, the logic is broken when we add a new FID which is not the port-based default. Now the port-based default FID only corresponds to standalone ports, and FDB/MDB entries belong to the bridging service. So while in the future, when the DSA API will support FDB isolation, we will have to figure out the FID based on the bridge number, for now there's a single bridging FID, so hardcode that. Lastly, the tagger needs to check, when it is transmitting a VLAN untagged skb, whether it is sending it towards a bridged or a standalone port. When we see it is bridged we assume the bridge is VLAN-unaware. Not because it cannot be VLAN-aware but: - if we are transmitting from a VLAN-aware bridge we are likely doing so using TX forwarding offload. That code path guarantees that skbs have a vlan hwaccel tag in them, so we would not enter the "else" branch of the "if (skb->protocol == htons(ETH_P_8021Q))" condition. - if we are transmitting on behalf of a VLAN-aware bridge but with no TX forwarding offload (no PVT support, out of space in the PVT, whatever), we would indeed be transmitting with VLAN 4095 instead of the bridge device's pvid. However we would be injecting a "From CPU" frame, and the switch won't learn from that - it only learns from "Forward" frames. So it is inconsequential for address learning. And VLAN 4095 is absolutely enough for the frame to exit the switch, since we never remove that VLAN from any port. Fixes: 57e661aae6a8 ("net: dsa: mv88e6xxx: Link aggregation support") Reported-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-09net: dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unawareVladimir Oltean4-6/+76
The VLAN support in mv88e6xxx has a loaded history. Commit 2ea7a679ca2a ("net: dsa: Don't add vlans when vlan filtering is disabled") noticed some issues with VLAN and decided the best way to deal with them was to make the DSA core ignore VLANs added by the bridge while VLAN awareness is turned off. Those issues were never explained, just presented as "at least one corner case". That approach had problems of its own, presented by commit 54a0ed0df496 ("net: dsa: provide an option for drivers to always receive bridge VLANs") for the DSA core, followed by commit 1fb74191988f ("net: dsa: mv88e6xxx: fix vlan setup") which applied ds->configure_vlan_while_not_filtering = true for mv88e6xxx in particular. We still don't know what corner case Andrew saw when he wrote commit 2ea7a679ca2a ("net: dsa: Don't add vlans when vlan filtering is disabled"), but Tobias now reports that when we use TX forwarding offload, pinging an external station from the bridge device is broken if the front-facing DSA user port has flooding turned off. The full description is in the link below, but for short, when a mv88e6xxx port is under a VLAN-unaware bridge, it inherits that bridge's pvid. So packets ingressing a user port will be classified to e.g. VID 1 (assuming that value for the bridge_default_pvid), whereas when tag_dsa.c xmits towards a user port, it always sends packets using a VID of 0 if that port is standalone or under a VLAN-unaware bridge - or at least it did so prior to commit d82f8ab0d874 ("net: dsa: tag_dsa: offload the bridge forwarding process"). In any case, when there is a conversation between the CPU and a station connected to a user port, the station's MAC address is learned in VID 1 but the CPU tries to transmit through VID 0. The packets reach the intended station, but via flooding and not by virtue of matching the existing ATU entry. DSA has established (and enforced in other drivers: sja1105, felix, mt7530) that a VLAN-unaware port should use a private pvid, and not inherit the one from the bridge. The bridge's pvid should only be inherited when that bridge is VLAN-aware, so all state transitions need to be handled. On the other hand, all bridge VLANs should sit in the VTU starting with the moment when the bridge offloads them via switchdev, they are just not used. This solves the problem that Tobias sees because packets ingressing on VLAN-unaware user ports now get classified to VID 0, which is also the VID used by tag_dsa.c on xmit. Fixes: d82f8ab0d874 ("net: dsa: tag_dsa: offload the bridge forwarding process") Link: https://patchwork.kernel.org/project/netdevbpf/patch/20211003222312.284175-2-vladimir.oltean@nxp.com/#24491503 Reported-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-08Merge tag 'asm-generic-fixes-5.15' of ↵Linus Torvalds2-1/+2
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic Pull asm-generic fixes from Arnd Bergmann: "There is one build fix for Arm platforms that ended up impacting most architectures because of the way the drivers/firmware Kconfig file is wired up: The CONFIG_QCOM_SCM dependency have caused a number of randconfig regressions over time, and some still remain in v5.15-rc4. The fix we agreed on in the end is to make this symbol selected by any driver using it, and then building it even for non-Arm platforms with CONFIG_COMPILE_TEST. To make this work on all architectures, the drivers/firmware/Kconfig file needs to be included for all architectures to make the symbol itself visible. In a separate discussion, we found that a sound driver patch that is pending for v5.16 needs the same change to include this Kconfig file, so the easiest solution seems to have my Kconfig rework included in v5.15. Finally, the branch also includes a small unrelated build fix for NOMMU architectures" Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/ Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/ Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/ * tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere qcom_scm: hide Kconfig symbol firmware: include drivers/firmware/Kconfig unconditionally
2021-10-08net: stmmac: add support for dwmac 3.40aHerve Codina2-0/+9
dwmac 3.40a is an old ip version that can be found on SPEAr3xx soc. Signed-off-by: Herve Codina <herve.codina@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08net: stmmac: fix get_hw_feature() on old hardwareHerve Codina4-9/+22
Some old IPs do not provide the hardware feature register. On these IPs, this register is read 0x00000000. In old driver version, this feature was handled but a regression came with the commit f10a6a3541b4 ("stmmac: rework get_hw_feature function"). Indeed, this commit removes the return value in dma->get_hw_feature(). This return value was used to indicate the validity of retrieved information and used later on in stmmac_hw_init() to override priv->plat data if this hardware feature were valid. This patch restores the return code in ->get_hw_feature() in order to indicate the hardware feature validity and override priv->plat data only if this hardware feature is valid. Fixes: f10a6a3541b4 ("stmmac: rework get_hw_feature function") Signed-off-by: Herve Codina <herve.codina@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-07Merge tag 'net-5.15-rc5' of ↵Linus Torvalds36-170/+332
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Including fixes from xfrm, bpf, netfilter, and wireless. Current release - regressions: - xfrm: fix XFRM_MSG_MAPPING ABI breakage caused by inserting a new value in the middle of an enum - unix: fix an issue in unix_shutdown causing the other end read/write failures - phy: mdio: fix memory leak Current release - new code bugs: - mlx5e: improve MQPRIO resiliency against bad configs Previous releases - regressions: - bpf: fix integer overflow leading to OOB access in map element pre-allocation - stmmac: dwmac-rk: fix ethernet on rk3399 based devices - netfilter: conntrack: fix boot failure with nf_conntrack.enable_hooks=1 - brcmfmac: revert using ISO3166 country code and 0 rev as fallback - i40e: fix freeing of uninitialized misc IRQ vector - iavf: fix double unlock of crit_lock Previous releases - always broken: - bpf, arm: fix register clobbering in div/mod implementation - netfilter: nf_tables: correct issues in netlink rule change event notifications - dsa: tag_dsa: fix mask for trunked packets - usb: r8152: don't resubmit rx immediately to avoid soft lockup on device unplug - i40e: fix endless loop under rtnl if FW fails to correctly respond to capability query - mlx5e: fix rx checksum offload coexistence with ipsec offload - mlx5: force round second at 1PPS out start time and allow it only in supported clock modes - phy: pcs: xpcs: fix incorrect CL37 AN sequence, EEE disable sequence Misc: - xfrm: slightly rejig the new policy uAPI to make it less cryptic" * tag 'net-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits) net: prefer socket bound to interface when not in VRF iavf: fix double unlock of crit_lock i40e: Fix freeing of uninitialized misc IRQ vector i40e: fix endless loop under rtnl dt-bindings: net: dsa: marvell: fix compatible in example ionic: move filter sync_needed bit set gve: report 64bit tx_bytes counter from gve_handle_report_stats() gve: fix gve_get_stats() rtnetlink: fix if_nlmsg_stats_size() under estimation gve: Properly handle errors in gve_assign_qpl gve: Avoid freeing NULL pointer gve: Correct available tx qpl check unix: Fix an issue in unix_shutdown causing the other end read/write failures net: stmmac: trigger PCS EEE to turn off on link down net: pcs: xpcs: fix incorrect steps on disable EEE netlink: annotate data races around nlk->bound net: pcs: xpcs: fix incorrect CL37 AN sequence net: sfp: Fix typo in state machine debug string net/sched: sch_taprio: properly cancel timer from taprio_destroy() net: bridge: fix under estimation in br_get_linkxstats_size() ...
2021-10-07qcom_scm: hide Kconfig symbolArnd Bergmann2-1/+2
Now that SCM can be a loadable module, we have to add another dependency to avoid link failures when ipa or adreno-gpu are built-in: aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe': ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available' ld.lld: error: undefined symbol: qcom_scm_is_available >>> referenced by adreno_gpu.c >>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a This can happen when CONFIG_ARCH_QCOM is disabled and we don't select QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd use a similar dependency here to what we have for QCOM_RPROC_COMMON, but that causes dependency loops from other things selecting QCOM_SCM. This appears to be an endless problem, so try something different this time: - CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on' but that is simply selected by all of its users - All the stubs in include/linux/qcom_scm.h can go away - arm-smccc.h needs to provide a stub for __arm_smccc_smc() to allow compile-testing QCOM_SCM on all architectures. - To avoid a circular dependency chain involving RESET_CONTROLLER and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement. According to my testing this still builds fine, and the QCOM platform selects this symbol already. Acked-by: Kalle Valo <kvalo@codeaurora.org> Acked-by: Alex Elder <elder@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-10-06iavf: fix double unlock of crit_lockStefan Assmann1-1/+0
The crit_lock mutex could be unlocked twice as reported here https://lists.osuosl.org/pipermail/intel-wired-lan/Week-of-Mon-20210823/025525.html Remove the superfluous unlock. Technically the problem was already present before 5ac49f3c2702 as that commit only replaced the locking primitive, but no functional change. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 5ac49f3c2702 ("iavf: use mutexes for locking of critical sections") Fixes: bac8486116b0 ("iavf: Refactor the watchdog state machine") Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-06i40e: Fix freeing of uninitialized misc IRQ vectorSylwester Dziedziuch1-1/+2
When VSI set up failed in i40e_probe() as part of PF switch set up driver was trying to free misc IRQ vectors in i40e_clear_interrupt_scheme and produced a kernel Oops: Trying to free already-free IRQ 266 WARNING: CPU: 0 PID: 5 at kernel/irq/manage.c:1731 __free_irq+0x9a/0x300 Workqueue: events work_for_cpu_fn RIP: 0010:__free_irq+0x9a/0x300 Call Trace: ? synchronize_irq+0x3a/0xa0 free_irq+0x2e/0x60 i40e_clear_interrupt_scheme+0x53/0x190 [i40e] i40e_probe.part.108+0x134b/0x1a40 [i40e] ? kmem_cache_alloc+0x158/0x1c0 ? acpi_ut_update_ref_count.part.1+0x8e/0x345 ? acpi_ut_update_object_reference+0x15e/0x1e2 ? strstr+0x21/0x70 ? irq_get_irq_data+0xa/0x20 ? mp_check_pin_attr+0x13/0xc0 ? irq_get_irq_data+0xa/0x20 ? mp_map_pin_to_irq+0xd3/0x2f0 ? acpi_register_gsi_ioapic+0x93/0x170 ? pci_conf1_read+0xa4/0x100 ? pci_bus_read_config_word+0x49/0x70 ? do_pci_enable_device+0xcc/0x100 local_pci_probe+0x41/0x90 work_for_cpu_fn+0x16/0x20 process_one_work+0x1a7/0x360 worker_thread+0x1cf/0x390 ? create_worker+0x1a0/0x1a0 kthread+0x112/0x130 ? kthread_flush_work_fn+0x10/0x10 ret_from_fork+0x1f/0x40 The problem is that at that point misc IRQ vectors were not allocated yet and we get a call trace that driver is trying to free already free IRQ vectors. Add a check in i40e_clear_interrupt_scheme for __I40E_MISC_IRQ_REQUESTED PF state before calling i40e_free_misc_vector. This state is set only if misc IRQ vectors were properly initialized. Fixes: c17401a1dd21 ("i40e: use separate state bit for miscellaneous IRQ setup") Reported-by: PJ Waskiewicz <pwaskiewicz@jumptrading.com> Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-06i40e: fix endless loop under rtnlJiri Benc1-1/+1
The loop in i40e_get_capabilities can never end. The problem is that although i40e_aq_discover_capabilities returns with an error if there's a firmware problem, the returned error is not checked. There is a check for pf->hw.aq.asq_last_status but that value is set to I40E_AQ_RC_OK on most firmware problems. When i40e_aq_discover_capabilities encounters a firmware problem, it will encounter the same problem on its next invocation. As the result, the loop becomes endless. We hit this with I40E_ERR_ADMIN_QUEUE_TIMEOUT but looking at the code, it can happen with a range of other firmware errors. I don't know what the correct behavior should be: whether the firmware should be retried a few times, or whether pf->hw.aq.asq_last_status should be always set to the encountered firmware error (but then it would be pointless and can be just replaced by the i40e_aq_discover_capabilities return value). However, the current behavior with an endless loop under the rtnl mutex(!) is unacceptable and Intel has not submitted a fix, although we explained the bug to them 7 months ago. This may not be the best possible fix but it's better than hanging the whole system on a firmware bug. Fixes: 56a62fc86895 ("i40e: init code and hardware support") Tested-by: Stefan Assmann <sassmann@redhat.com> Signed-off-by: Jiri Benc <jbenc@redhat.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-06ionic: move filter sync_needed bit setShannon Nelson2-4/+3
Move the setting of the filter-sync-needed bit to the error case in the filter add routine to be sure we're checking the live filter status rather than a copy of the pre-sync status. Fixes: 969f84394604 ("ionic: sync the filters in the work task") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-06gve: report 64bit tx_bytes counter from gve_handle_report_stats()Eric Dumazet1-2/+3
Each tx queue maintains a 64bit counter for bytes, there is no reason to truncate this to 32bit (or this has not been documented) Fixes: 24aeb56f2d38 ("gve: Add Gvnic stats AQ command and ethtool show/set-priv-flags.") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yangchun Fu <yangchun@google.com> Cc: Kuo Zhao <kuozhao@google.com> Cc: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-06gve: fix gve_get_stats()Eric Dumazet1-4/+9
gve_get_stats() can report wrong numbers if/when u64_stats_fetch_retry() returns true. What is needed here is to sample values in temporary variables, and only use them after each loop is ended. Fixes: f5cedc84a30d ("gve: Add transmit and receive support") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Catherine Sullivan <csully@google.com> Cc: Sagi Shahar <sagis@google.com> Cc: Jon Olson <jonolson@google.com> Cc: Willem de Bruijn <willemb@google.com> Cc: Luigi Rizzo <lrizzo@google.com> Cc: Jeroen de Borst <jeroendb@google.com> Cc: Tao Liu <xliutaox@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-06gve: Properly handle errors in gve_assign_qplCatherine Sullivan1-1/+7
Ignored errors would result in crash. Fixes: ede3fcf5ec67f ("gve: Add support for raw addressing to the rx path") Signed-off-by: Catherine Sullivan <csully@google.com> Signed-off-by: Jeroen de Borst <jeroendb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-06gve: Avoid freeing NULL pointerTao Liu1-10/+17
Prevent possible crashes when cleaning up after unsuccessful initializations. Fixes: 893ce44df5658 ("gve: Add basic driver framework for Compute Engine Virtual NIC") Signed-off-by: Tao Liu <xliutaox@google.com> Signed-off-by: Catherine Sully <csully@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-06gve: Correct available tx qpl checkCatherine Sullivan1-1/+1
The qpl_map_size is rounded up to a multiple of sizeof(long), but the number of qpls doesn't have to be. Fixes: f5cedc84a30d2 ("gve: Add transmit and receive support") Signed-off-by: Catherine Sullivan <csully@google.com> Signed-off-by: Jeroen de Borst <jeroendb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-06net: stmmac: trigger PCS EEE to turn off on link downWong Vee Khee1-1/+5
The current implementation enable PCS EEE feature in the event of link up, but PCS EEE feature is not disabled on link down. This patch makes sure PCE EEE feature is disabled on link down. Fixes: 656ed8b015f1 ("net: stmmac: fix EEE init issue when paired with EEE capable PHYs") Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-06net: pcs: xpcs: fix incorrect steps on disable EEEWong Vee Khee1-4/+9
When Energy-Efficient Ethernet(EEE) is disable from the MAC side, we need to clear the DW_VR_MII_EEE_TRN_LPI bit of DW_VR_MII_EEE_MCTRL1 register. Fixes: 7617af3d1a5e ("net: pcs: Introducing support for DWC xpcs Energy Efficient Ethernet") Cc: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com> Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-05net: pcs: xpcs: fix incorrect CL37 AN sequenceWong Vee Khee1-5/+27
According to Synopsys DesignWare Cores Ethernet PCS databook, it is required to disable Clause 37 auto-negotiation by programming bit-12 (AN_ENABLE) to 0 if it is already enabled, before programming various fields of VR_MII_AN_CTRL registers. After all these programming are done, it is then required to enable Clause 37 auto-negotiation by programming bit-12 (AN_ENABLE) to 1. Fixes: b97b5331b8ab ("net: pcs: add C37 SGMII AN support for intel mGbE controller") Cc: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-05net: sfp: Fix typo in state machine debug stringSean Anderson1-1/+1
The string should be "tx_disable" to match the state enum. Fixes: 4005a7cb4f55 ("net: phy: sftp: print debug message with text, not numbers") Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-05r8152: avoid to resubmit rx immediatelyHayes Wang1-1/+15
For the situation that the disconnect event comes very late when the device is unplugged, the driver would resubmit the RX bulk transfer after getting the callback with -EPROTO immediately and continually. Finally, soft lockup occurs. This patch avoids to resubmit RX immediately. It uses a workqueue to schedule the RX NAPI. And the NAPI would resubmit the RX. It let the disconnect event have opportunity to stop the submission before soft lockup. Reported-by: Jason-ch Chen <jason-ch.chen@mediatek.com> Tested-by: Jason-ch Chen <jason-ch.chen@mediatek.com> Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-03Merge tag 'driver-core-5.15-rc4' of ↵Linus Torvalds1-0/+4
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core fixes from Greg KH: "Here are some driver core and kernfs fixes for reported issues for 5.15-rc4. These fixes include: - kernfs positive dentry bugfix - debugfs_create_file_size error path fix - cpumask sysfs file bugfix to preserve the user/kernel abi (has been reported multiple times.) - devlink fixes for mdiobus devices as reported by the subsystem maintainers. Also included in here are some devlink debugging changes to make it easier for people to report problems when asked. They have already helped with the mdiobus and other subsystems reporting issues. All of these have been linux-next for a while with no reported issues" * tag 'driver-core-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: kernfs: also call kernfs_set_rev() for positive dentry driver core: Add debug logs when fwnode links are added/deleted driver core: Create __fwnode_link_del() helper function driver core: Set deferred probe reason when deferred by driver core net: mdiobus: Set FWNODE_FLAG_NEEDS_CHILD_BOUND_ON_ADD for mdiobus parents driver core: fw_devlink: Add support for FWNODE_FLAG_NEEDS_CHILD_BOUND_ON_ADD driver core: fw_devlink: Improve handling of cyclic dependencies cpumask: Omit terminating null byte in cpumap_print_{list,bitmask}_to_buf debugfs: debugfs_create_file_size(): use IS_ERR to check for error
2021-10-02net: stmmac: dwmac-rk: Fix ethernet on rk3399 based devicesPunit Agrawal1-0/+5
Commit 2d26f6e39afb ("net: stmmac: dwmac-rk: fix unbalanced pm_runtime_enable warnings") while getting rid of a runtime PM warning ended up breaking ethernet on rk3399 based devices. By dropping an extra reference to the device, the commit ends up enabling suspend / resume of the ethernet device - which appears to be broken. While the issue with runtime pm is being investigated, partially revert commit 2d26f6e39afb to restore the network on rk3399. Fixes: 2d26f6e39afb ("net: stmmac: dwmac-rk: fix unbalanced pm_runtime_enable warnings") Suggested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Punit Agrawal <punitagrawal@gmail.com> Cc: Michael Riesch <michael.riesch@wolfvision.net> Tested-by: Heiko Stuebner <heiko@sntech.de> Link: https://lore.kernel.org/r/20210929135049.3426058-1-punitagrawal@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-02net: mscc: ocelot: fix VCAP filters remaining active after being deletedVladimir Oltean1-2/+2
When ocelot_flower.c calls ocelot_vcap_filter_add(), the filter has a given filter->id.cookie. This filter is added to the block->rules list. However, when ocelot_flower.c calls ocelot_vcap_block_find_filter_by_id() which passes the cookie as argument, the filter is never found by filter->id.cookie when searching through the block->rules list. This is unsurprising, since the filter->id.cookie is an unsigned long, but the cookie argument provided to ocelot_vcap_block_find_filter_by_id() is a signed int, and the comparison fails. Fixes: 50c6cc5b9283 ("net: mscc: ocelot: store a namespaced VCAP filter ID") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20210930125330.2078625-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-01Merge tag 'mlx5-fixes-2021-09-30' of ↵David S. Miller14-105/+194
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux mlx5-fixes-2021-09-30
2021-10-01Merge tag 'wireless-drivers-2021-10-01' of ↵David S. Miller8-25/+24
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers wireless-drivers fixes for v5.15 Second set of fixes for v5.15, nothing major this time. Most important here are reverting a brcmfmac regression and a fix for an old rare ath5k build error. iwlwifi * fixes to NULL dereference, off by one and missing unlock * add support for Killer AX1650 on Dell XPS 15 (9510) laptop ath5k * build fix with LEDS=m brcmfmac * revert a regression causing BCM4359/9 devices stop working as access point mwifiex * fix clang warning about null pointer arithmetic
2021-10-01phy: mdio: fix memory leakPavel Skripkin1-0/+7
Syzbot reported memory leak in MDIO bus interface, the problem was in wrong state logic. MDIOBUS_ALLOCATED indicates 2 states: 1. Bus is only allocated 2. Bus allocated and __mdiobus_register() fails, but device_register() was called In case of device_register() has been called we should call put_device() to correctly free the memory allocated for this device, but mdiobus_free() calls just kfree(dev) in case of MDIOBUS_ALLOCATED state To avoid this behaviour we need to set bus->state to MDIOBUS_UNREGISTERED _before_ calling device_register(), because put_device() should be called even in case of device_register() failure. Link: https://lore.kernel.org/netdev/YVMRWNDZDUOvQjHL@shell.armlinux.org.uk/ Fixes: 46abc02175b3 ("phylib: give mdio buses a device tree presence") Reported-and-tested-by: syzbot+398e7dc692ddbbb4cfec@syzkaller.appspotmail.com Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Link: https://lore.kernel.org/r/eceae1429fbf8fa5c73dd2a0d39d525aa905074d.1633024062.git.paskripkin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-01Revert "net: mdiobus: Fix memory leak in __mdiobus_register"Pavel Skripkin1-1/+0
This reverts commit ab609f25d19858513919369ff3d9a63c02cd9e2e. This patch is correct in the sense that we _should_ call device_put() in case of device_register() failure, but the problem in this code is more vast. We need to set bus->state to UNMDIOBUS_REGISTERED before calling device_register() to correctly release the device in mdiobus_free(). This patch prevents us from doing it, since in case of device_register() failure put_device() will be called 2 times and it will cause UAF or something else. Also, Reported-by: tag in revered commit was wrong, since syzbot reported different leak in same function. Link: https://lore.kernel.org/netdev/20210928092657.GI2048@kadam/ Acked-by: Yanfei Xu <yanfei.xu@windriver.com> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Link: https://lore.kernel.org/r/f12fb1faa4eccf0f355788225335eb4309ff2599.1633024062.git.paskripkin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-01net/mlx5e: Mutually exclude setting of TX-port-TS and MQPRIO in channel modeAya Levin2-0/+19
TX-port-TS hijacks the PTP traffic to a specific HW TX-queue. This conflicts with MQPRIO in channel mode, which specifies explicitly which TC accepts the packet. This patch mutually excludes the above configuration. Fixes: ec60c4581bd9 ("net/mlx5e: Support MQPRIO channel mode") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-11 19:56:27 +0300