| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 4925642d541278575ad1948c5924d71ffd57ef14 ]
In tests with two Lima boards from 8devices (QCA4531 based) on OpenWrt
19.07 we could force a silent restart of a device with no serial
output when we were sending a high amount of UDP traffic (iperf3 at 80
MBit/s in both directions from external hosts, saturating the wifi and
causing a load of about 4.5 to 6) and were then triggering an
ath9k_queue_reset().
Further debugging showed that the restart was caused by the ath79
watchdog. With disabled watchdog we could observe that the device was
constantly going into ath_isr() interrupt handler and was returning
early after the ATH_OP_HW_RESET flag test, without clearing any
interrupts. Even though ath9k_queue_reset() calls
ath9k_hw_kill_interrupts().
With JTAG we could observe the following race condition:
1) ath9k_queue_reset()
...
-> ath9k_hw_kill_interrupts()
-> set_bit(ATH_OP_HW_RESET, &common->op_flags);
...
<- returns
2) ath9k_tasklet()
...
-> ath9k_hw_resume_interrupts()
...
<- returns
3) loops around:
...
handle_int()
-> ath_isr()
...
-> if (test_bit(ATH_OP_HW_RESET,
&common->op_flags))
return IRQ_HANDLED;
x) ath_reset_internal():
=> never reached <=
And in ath_isr() we would typically see the following interrupts /
interrupt causes:
* status: 0x00111030 or 0x00110030
* async_cause: 2 (AR_INTR_MAC_IPQ)
* sync_cause: 0
So the ath9k_tasklet() reenables the ath9k interrupts
through ath9k_hw_resume_interrupts() which ath9k_queue_reset() had just
disabled. And ath_isr() then keeps firing because it returns IRQ_HANDLED
without actually clearing the interrupt.
To fix this IRQ storm also clear/disable the interrupts again when we
are in reset state.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Fixes: 872b5d814f99 ("ath9k: do not access hardware on IRQs during reset")
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914192515.9273-3-linus.luessing@c0d3.blue
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 747ff7d3d7424876111b7559b7f6704762f89796 ]
When rebooting on sc7180 Trogdor devices I see the following crash from
the wifi driver.
ath10k_snoc 18800000.wifi: firmware crashed! (guid 83493570-29a2-4e98-a83e-70048c47669c)
This is because a modem stop event looks just like a firmware crash to
the driver, the qmi connection is closed in both cases. Use the qcom ssr
notifier block to stop treating the qmi connection close event as a
firmware crash signal when the modem hasn't actually crashed. See
ath10k_qmi_event_server_exit() for more details.
This silences the crash message seen during every reboot.
Fixes: 3f14b73c3843 ("ath10k: Enable MSA region dump support for WCN3990")
Cc: Youghandhar Chintala <youghand@codeaurora.org>
Cc: Abhishek Kumar <kuabhs@chromium.org>
Cc: Steev Klimaszewski <steev@kali.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rakesh Pillai <pillair@codeaurora.org>
Tested-By: Youghandhar Chintala <youghand@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210922233341.182624-1-swboyd@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 019edd01d174ce4bb2e517dd332922514d176601 ]
On a i.MX-based board with a QCA9377 Wifi chip, the following errors
are seen after launching the 'hostapd' application:
hostapd /etc/wifi.conf
Configuration file: /etc/wifi.conf
wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
Using interface wlan0 with hwaddr 00:1f:7b:31:04:a0 and ssid "thessid"
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: interface state COUNTRY_UPDATE->ENABLED
wlan0: AP-ENABLED
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
...
Fix this problem by adding the BH locking around napi-schedule(),
in the same way it was done in commit e63052a5dd3c ("mlx5e: add
add missing BH locking around napi_schdule()").
Its commit log provides the following explanation:
"It's not correct to call napi_schedule() in pure process
context. Because we use __raise_softirq_irqoff() we require
callers to be in a context which will eventually lead to
softirq handling (hardirq, bh disabled, etc.).
With code as is users will see:
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
"
Fixes: cfee8793a74d ("ath10k: enable napi on RX path for sdio")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210824144339.2796122-1-festevam@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e6dfbc3ba90cc2b619229be56b485f085a0a8e1c ]
When receiving a beacon or probe response, we should update the
boottime_ns field which is the timestamp the frame was received at.
(cf mac80211.h)
This fixes a scanning issue with Android since it relies on this
timestamp to determine when the AP has been seen for the last time
(via the nl80211 BSS_LAST_SEEN_BOOTTIME parameter).
Fixes: 5e3dd157d7e7 ("ath10k: mac80211 driver for Qualcomm Atheros 802.11ac CQA98xx devices")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1629811733-7927-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 72de799aa9e3e064b35238ef053d2f0a49db055a ]
The buffer pointed to by event is not freed in case
ATH11K_FLAG_UNREGISTERING bit is set, resulting in
memory leak, so fix it.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913180246.193388-4-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9d6ae1f5cf733c0e8d7f904c501fd015c4b9f0f4 ]
Frequency in rx status is being filled incorrectly in the 6 GHz band as
channel number received is invalid in this case which is causing packet
drops. So fix that.
Fixes: 5dcf42f8b79d ("ath11k: Use freq instead of channel number in rx path")
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210722102054.43419-2-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1db2b0d0a39102238fcbf9092cefa65a710642e9 ]
Whenever ath11k is bootup with a user country already set, cfg80211
notifies this country info to ath11k soon after registration, where the
notification is sent to the firmware for fetching the rules of this user
country input.
Multiple race conditions could be seen in this scenario where a new
request is either lost as pointed in [1] or a new regd overwrites the
default regd provided by the firmware during bootup. Note that, the
default regd is used for intersection purpose and hence it should not be
overwritten.
The main reason as pointed by [1] is the usage of ATH11K_FLAG_REGISTERED
flag which is updated after completion of core registration, whereas the
reg notification from cfg80211 and wmi events for the corresponding
request can happen much before that. Since the ATH11K_FLAG_REGISTERED is
currently used to determine if the event containing reg rules belong to
default regd or for user request, there is a possibility of the default
regd getting overwritten.
Since the default reg rules will be received only once per pdev on
firmware load, the above flag based check can be replaced with a check
to see if default_regd is already set, so that we can now always update
the new_regd. Also if the new_regd is set, this will be always used to
update the reg rules for the registered phy.
[1] https://patchwork.kernel.org/project/linux-wireless/patch/1829665.1PRlr7bOQj@ripper/
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-4-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aadf7c81a0771b8f1c97dabca6a48bae1b387779 ]
The ath11k_dbring_bufs_replenish() and ath11k_dbring_fill_bufs()
take a "gfp" parameter but they since they take spinlocks, the
allocations they do have to be atomic. This causes a bug because
ath11k_dbring_buf_setup passes GFP_KERNEL for the gfp flags.
The fix is to use GFP_ATOMIC and remove the unused parameters.
Fixes: bd6478559e27 ("ath11k: Add direct buffer ring support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210812070434.GE31863@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3c719fed0f3a5e95b1d164609ecc81c4191ade70 ]
When the BSS reference holds a valid reference, it is not freed. The 'if'
condition is wrong. Instead of the 'if (bss)' check, the 'if (!bss)' check
is used.
The issue is solved by removing the unnecessary 'if' check because
cfg80211_put_bss() already performs the NULL validation.
Fixes: 6cd4fa5ab691 ("staging: wilc1000: make use of cfg80211_inform_bss_frame()")
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-3-ajay.kathat@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 701668d3bfa03dabc5095fc383d5315544ee5b31 ]
We have been tracking a strange bug with Antenna Diversity Switching (ADS)
on wcn3680b for a while.
ADS is configured like this:
A. Via a firmware configuration table baked into the NV area.
1. Defines if ADS is enabled.
2. Defines which GPIOs are connected to which antenna enable pin.
3. Defines which antenna/GPIO is primary and which is secondary.
B. WCN36XX_CFG_VAL(ANTENNA_DIVERSITY, N)
N is a bitmask of available antenna.
Setting N to 3 indicates a bitmask of enabled antenna (1 | 2).
Obviously then we can set N to 1 or N to 2 to fix to a particular
antenna and disable antenna diversity.
C. WCN36XX_CFG_VAL(ASD_PROBE_INTERVAL, XX)
XX is the number of beacons between each antenna RSSI check.
Setting this value to 50 means, every 50 received beacons, run the
ADS algorithm.
D. WCN36XX_CFG_VAL(ASD_TRIGGER_THRESHOLD, YY)
YY is a two's complement integer which specifies the RSSI decibel
threshold below which ADS will run.
We default to -60db here, meaning a measured RSSI <= -60db will
trigger an ADS probe.
E. WCN36XX_CFG_VAL(ASD_RTT_RSSI_HYST_THRESHOLD, Z)
Z is a hysteresis value, indicating a delta which the RSSI must
exceed for the antenna switch to be valid.
For example if HYST_THRESHOLD == 3 AntennaId1-RSSI == -60db and
AntennaId-2-RSSI == -58db then firmware will not switch antenna.
The threshold needs to be -57db or better to satisfy the criteria.
F. A firmware feature bit also exists ANTENNA_DIVERSITY_SELECTION.
This feature bit is used by the firmware to report if
ANTENNA_DIVERSITY_SELECTION is supported. The host is not required to
toggle this bit to enable or disable ADS.
ADS works like this:
A. Every XX beacons the firmware switches to or remains on the primary
antenna.
B. The firmware then sends a Request-To-Send (RTS) packet to the AP.
C. The firmware waits for a Clear-To-Send (CTS) response from the AP.
D. The firmware then notes the received RSSI on the CTS packet.
E. The firmware then repeats steps A-D on the secondary antenna.
F. Subsequently if the RSSI on the measured antenna is better than
ASD_TRIGGER_THRESHOLD + the active antenna's RSSI then the
measured antenna becomes the active antenna.
G. If RSSI rises past ASD_TRIGGER_THRESHOLD then ADS doesn't run at
all even if there is a substantially better RSSI on the alternative
antenna.
What we have been observing is that the RTS packet is being sent but the
MAC address is a byte-swapped version of the target MAC. The ADS/RTS MAC is
corrupted only when the link is encrypted, if the AP is open the RTS MAC is
correct. Similarly if we configure the firmware to an RTS/CTS sequence for
regular data - the transmitted RTS MAC is correctly formatted.
Internally the wcn36xx firmware uses the indexes in the SMD commands to
populate and extract data from specific entries in an STA lookup table. The
AP's MAC appears a number of times in different indexes within this lookup
table, so the MAC address extracted for the data-transmit RTS and the MAC
address extracted for the ADS/RTS packet are not the same STA table index.
Our analysis indicates the relevant firmware STA table index is
"bssSelfStaIdx".
There is an STA populate function responsible for formatting the MAC
address of the bssSelfStaIdx including byte-swapping the MAC address.
Its clear then that the required STA populate command did not run for
bssSelfStaIdx.
So taking a look at the sequence of SMD commands sent to the firmware we
see the following downstream when moving from an unencrypted to encrypted
BSS setup.
- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_CONFIG_STA_REQ
- WLAN_HAL_SET_STAKEY_REQ
Upstream in wcn36xx we have
- WLAN_HAL_CONFIG_BSS_REQ
- WLAN_HAL_SET_STAKEY_REQ
The solution then is to add the missing WLAN_HAL_CONFIG_STA_REQ between
WLAN_HAL_CONFIG_BSS_REQ and WLAN_HAL_SET_STAKEY_REQ.
No surprise WLAN_HAL_CONFIG_STA_REQ is the routine responsible for
populating the STA lookup table in the firmware and once done the MAC sent
by the ADS routine is in the correct byte-order.
This bug is apparent with ADS but it is also the case that any other
firmware routine that depends on the "bssSelfStaIdx" would retrieve
malformed data on an encrypted link.
Fixes: 3e977c5c523d ("wcn36xx: Define wcn3680 specific firmware parameters")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210909144428.2564650-2-bryan.odonoghue@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 43ea9bd84f27d06482cc823d9749cc9dd2993bc8 ]
Firmware link offload monitoring can be made to work in 3/4 cases by
switching on firmware feature bit WLANACTIVE_OFFLOAD
- Secure power-save on
- Secure power-save off
- Open power-save on
However, with an open AP if we switch off power-saving - thus never
entering Beacon Mode Power Save - BMPS, firmware never forwards loss
of beacon upwards.
We had hoped that WLANACTIVE_OFFLOAD and some fixes for sequence numbers
would unblock this but, it hasn't and further investigation is required.
Its possible to have a complete set of Secure power-save on/off and Open
power-save on/off provided we use Linux' link monitoring mechanism.
While we debug the Open AP failure we need to fix upstream.
This reverts commit c973fdad79f6eaf247d48b5fc77733e989eb01e1.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025093037.3966022-2-bryan.odonoghue@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit df0697801d8aa2eebfe7f0b7388879639f8fe7cc ]
If the system is resumed because of an incoming packet, the wcn36xx RX
interrupts is fired before actual resuming of the wireless/mac80211
stack, causing any received packets to be simply dropped. E.g. a ping
request causes a system resume, but is dropped and so never forwarded
to the IP stack.
This change fixes that, disabling DMA interrupts on suspend to no pass
packets until mac80211 is resumed and ready to handle them.
Note that it's not incompatible with RX irq wake.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635150496-19290-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a27ca39478270e07baf9c09aa0c99709769ba03 ]
For packets originating from hardware scan, the channel and band is
included in the buffer descriptor (bd->rf_band & bd->rx_ch).
For 2Ghz band the channel value is directly reported in the 4-bit
rx_ch field. For 5Ghz band, the rx_ch field contains a mapping
index (given the 4-bit limitation).
The reserved0 value field is also used to extend 4-bit mapping to
5-bit mapping to support more than 16 5Ghz channels.
This change adds correct reporting of the frequency/band, that is
used in scan mechanism. And is required for 5Ghz hardware scan
support.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634554678-7993-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e5322b9ab5f63536c41301150b7ce64605ce52cc ]
Just like we have default SMPS mode as dynamic in powersave,
we should not enable RX-diversity in powersave, to reduce
power consumption when connected to a non-MIMO AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017113927.fc896bc5cdaa.I1d11da71b8a5cbe921a37058d5f578f1b14a2023@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 70382b0897eeecfcd35ba5f6161dbceeb556ea1e ]
JnP should not have the 160 MHz.
Signed-off-by: Yaara Baruch <yaara.baruch@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20211016114029.ee163f4a7513.I7f87bd969a0b038c7f3a1a962d9695ffd18c5da1@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 257051a235c17e33782b6e24a4b17f2d7915aaec ]
When the driver fails to request the firmware, it calls its error
handler. In the error handler, the driver detaches device from driver
first before releasing the firmware, which can cause a use-after-free bug.
Fix this by releasing firmware first.
The following log reveals it:
[ 9.007301 ] BUG: KASAN: use-after-free in mwl8k_fw_state_machine+0x320/0xba0
[ 9.010143 ] Workqueue: events request_firmware_work_func
[ 9.010830 ] Call Trace:
[ 9.010830 ] dump_stack_lvl+0xa8/0xd1
[ 9.010830 ] print_address_description+0x87/0x3b0
[ 9.010830 ] kasan_report+0x172/0x1c0
[ 9.010830 ] ? mutex_unlock+0xd/0x10
[ 9.010830 ] ? mwl8k_fw_state_machine+0x320/0xba0
[ 9.010830 ] ? mwl8k_fw_state_machine+0x320/0xba0
[ 9.010830 ] __asan_report_load8_noabort+0x14/0x20
[ 9.010830 ] mwl8k_fw_state_machine+0x320/0xba0
[ 9.010830 ] ? mwl8k_load_firmware+0x5f0/0x5f0
[ 9.010830 ] request_firmware_work_func+0x172/0x250
[ 9.010830 ] ? read_lock_is_recursive+0x20/0x20
[ 9.010830 ] ? process_one_work+0x7a1/0x1100
[ 9.010830 ] ? request_firmware_nowait+0x460/0x460
[ 9.010830 ] ? __this_cpu_preempt_check+0x13/0x20
[ 9.010830 ] process_one_work+0x9bb/0x1100
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634356979-6211-1-git-send-email-zheyuma97@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d45dac0732a287fc371a23f257cce04e65627947 ]
The bounds check on datalen is off-by-one, so fix it.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
channel_detector_create()
[ Upstream commit 4b6012a7830b813799a7faf40daa02a837e0fd5b ]
kzalloc() is used to allocate memory for cd->detectors, and if it fails,
channel_detector_exit() behind the label fail will be called:
channel_detector_exit(dpd, cd);
In channel_detector_exit(), cd->detectors is dereferenced through:
struct pri_detector *de = cd->detectors[i];
To fix this possible null-pointer dereference, check cd->detectors before
the for loop to dereference cd->detectors.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210805153854.154066-1-islituo@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 49c3eb3036e6359c5c20fe76c611a2c0e0d4710e ]
The Cyberbook T116 tablet contains quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43455-sdio.Default string-Default string.txt" as nvram file which
is way too generic.
The nvram file shipped on the factory Android image contains the exact
same settings as those used on the AcePC T8 mini PC, so point the new
DMI nvram filename quirk to the acepc-t8 nvram file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210928160633.96928-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c5a8e90730a322f236731fc347dd3afa5db5550e ]
When fw fifo dumps, RX clock gating should be disabled to avoid
something unexpected. However, the register operation ran into
a mistake. So, we fix it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210927111830.5354-1-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e263bdab9c0e8025fb7f41f153709a9cda51f6b6 ]
Beacon buffer for high latency devices does not use DMA. other similar
buffer allocation methods in the driver have already been modified for
high latency path. Fix the beacon buffer allocation left out in the
earlier high latency changes.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[fabio: adapt it to use ar->bus_param.dev_type ]
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210818232627.2040121-1-festevam@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 86a03dad0f5ad8182ed5fcf7bf3eec71cd96577c ]
For fragmented packets, ath11k reassembles each fragment as a normal
packet and then reinjects it into HW ring. In this case, the DMA
direction should be DMA_TO_DEVICE, not DMA_FROM_DEVICE, otherwise
invalid payload will be reinjected to HW and then delivered to host.
What is more, since arbitrary memory could be allocated to the frame, we
don't know what kind of data is contained in the buffer reinjected.
Thus, as a bad result, private info may be leaked.
Note that this issue is only found on Intel platform.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916064617.20006-1-bqiang@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 441b3b5911f8ead7f2fe2336587b340a33044d58 ]
When wlan interface is up, 11d scan is sent to the firmware, and the
firmware needs to spend couple of seconds to complete the 11d scan. If
immediately a normal scan from user space arrives to ath11k, then the
normal scan request is also sent to the firmware, but the scan started
event will be reported to ath11k until the 11d scan complete. When timed
out for the scan started in ath11k, ath11k stops the normal scan and the
firmware reports WMI_SCAN_EVENT_DEQUEUED to ath11k for the normal scan.
ath11k has no handler for the event and then timed out for the scan
completed in ath11k_scan_stop(), and ath11k prints the following error
message.
[ 1491.604750] ath11k_pci 0000:02:00.0: failed to receive scan abort comple: timed out
[ 1491.604756] ath11k_pci 0000:02:00.0: failed to stop scan: -110
[ 1491.604758] ath11k_pci 0000:02:00.0: failed to start hw scan: -110
Add a handler for WMI_SCAN_EVENT_DEQUEUED and then complete the scan to
get rid of the above error message.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914164226.38843-1-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 69a0fcf8a9f2273040d03e5ee77c9689c09e9d3a ]
During firmware recovery, the default reg rules which are
received via WMI_REG_CHAN_LIST_CC_EVENT can overwrite
the currently configured user regd.
See below snap for example,
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
root@OpenWrt:/# echo assert > /sys/kernel/debug/ath11k/ipq8074\ hw2.0/simulate_f
w_crash
<snip>
[ 5290.471696] ath11k c000000.wifi1: pdev 1 successfully recovered
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country US: DFS-FCC
country US: DFS-FCC
country US: DFS-FCC
In the above, the user configured country 'FR' is overwritten
when the rules of default country 'US' are received and updated during
recovery. Hence avoid processing of these rules in general
during firmware recovery as they have been already applied during
driver registration or after last set user country is configured.
This scenario applies for both AP and STA devices basically because
cfg80211 is not aware of the recovery and only the driver recovers, but
changing or resetting of the reg domain during recovery is not needed so
as to continue with the configured regdomain currently in use.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-3-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c606008b70627a2fc485732a53cc22f0f66d0981 ]
When creating a new virtual interface in mwifiex_add_virtual_intf(), we
update our internal driver states like bss_type, bss_priority, bss_role
and bss_mode to reflect the mode the firmware will be set to.
When switching virtual interface mode using
mwifiex_init_new_priv_params() though, we currently only update bss_mode
and bss_role. In order for the interface mode switch to actually work,
we also need to update bss_type to its proper value, so do that.
This fixes a crash of the firmware (because the driver tries to execute
commands that are invalid in AP mode) when switching from station mode
to AP mode.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-9-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c2e9666cdffd347460a2b17988db4cfaf2a68fb9 ]
We currently handle changing from the P2P to the STATION virtual
interface type slightly different than changing from P2P to ADHOC: When
changing to STATION, we don't send the SET_BSS_MODE command. We do send
that command on all other type-changes though, and it probably makes
sense to send the command since after all we just changed our BSS_MODE.
Looking at prior changes to this part of the code, it seems that this is
simply a leftover from old refactorings.
Since sending the SET_BSS_MODE command is the only difference between
mwifiex_change_vif_to_sta_adhoc() and the current code, we can now use
mwifiex_change_vif_to_sta_adhoc() for both switching to ADHOC and
STATION interface type.
This does not fix any particular bug and just "looked right", so there's
a small chance it might be a regression.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-4-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit feab5bb8f1d4621025dceae7eef62d5f92de34ac ]
pdev_id in structure 'wmi_pdev_bss_chan_info_event' is wrongly placed
at the beginning. This causes invalid values in survey dump. Hence, align
the structure with the firmware.
Note: The firmware releases follow this order since the feature was
implemented. Also, it is not changing across the branches including
QCA6390.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-3-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 31f97cf9f0c31143a2a6fcc89c4a1286ce20157e upstream.
The module parameters are missing dev_oper_mode 12, BT classic alone,
add it. Moreover, the parameters encode newlines, which ends up being
printed malformed e.g. by modinfo, so fix that too.
However, the module parameter string is duplicated in both USB and SDIO
modules and the dev_oper_mode mode enumeration in those module parameters
is a duplicate of macros used by the driver. Furthermore, the enumeration
is confusing.
So, deduplicate the module parameter string and use __stringify() to
encode the correct mode enumeration values into the module parameter
string. Finally, replace 'Wi-Fi' with 'Wi-Fi alone' and 'BT' with
'BT classic alone' to clarify what those modes really mean.
Fixes: 898b255339310 ("rsi: add module parameter operating mode")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Karun Eagalapati <karun256@gmail.com>
Cc: Martin Fuzzey <martin.fuzzey@flowbird.group>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: netdev@vger.kernel.org
Cc: <stable@vger.kernel.org> # 4.17+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916144245.10181-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b515d097053a71d624e0c5840b42cd4caa653941 upstream.
P2P client mode was only working the first time.
On subsequent connection attempts the group was successfully created but
no data was sent (no transmitted data packets were seen with a sniffer).
The reason for this was that the hardware was being configured in fixed
rate mode with rate RSI_RATE_1 (1Mbps) which is not valid in the 5GHz band.
In P2P mode wpa_supplicant uses NL80211_CMD_SET_TX_BITRATE_MASK to disallow
the 11b rates in the 2.4GHz band which updated common->fixedrate_mask.
rsi_set_min_rate() then used the fixedrate_mask to calculate the minimum
allowed rate, or 0xffff = auto if none was found.
However that calculation did not account for the different rate sets
allowed in the different bands leading to the error.
Fixing set_min_rate() would result in 6Mb/s being used all the time
which is not what we want either.
The reason the problem did not occur on the first connection is that
rsi_mac80211_set_rate_mask() only updated the fixedrate_mask for
the *current* band. When it was called that was still 2.4GHz as the
switch is done later. So the when set_min_rate() was subsequently
called after the switch to 5GHz it still had a mask of zero, leading
to defaulting to auto mode.
Fix this by differentiating the case of a single rate being
requested, in which case the hardware will be used in fixed rate
mode with just that rate, and multiple rates being requested,
in which case we remain in auto mode but the firmware rate selection
algorithm is configured with a restricted set of rates.
Fixes: dad0d04fa7ba ("rsi: Add RS9113 wireless driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-4-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 99ac6018821253ec67f466086afb63fc18ea48e2 upstream.
My previous patch checked if encryption should be enabled by directly
checking info->control.hw_key (like the downstream driver).
However that missed that the control and driver_info members of
struct ieee80211_tx_info are union fields.
Due to this when rsi_core_xmit() updates fields in "tx_params"
(driver_info) it can overwrite the control.hw_key, causing the result
of the later test to be incorrect.
With the current structure layout the first byte of control.hw_key is
overlayed with the vap_id so, since we only test if control.hw_key is
NULL / non NULL, a non zero vap_id will incorrectly enable encryption.
In basic STA and AP modes the vap_id is always zero so it works but in
P2P client mode a second VIF is created causing vap_id to be non zero
and hence encryption to be enabled before keys have been set.
Fix this by extracting the key presence flag to a new field in the driver
private tx_params structure and populating it first.
Fixes: 314538041b56 ("rsi: fix AP mode with WPA failure due to encrypted EAPOL")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-3-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9b14ed6e11b72dd4806535449ca6c6962cb2369d upstream.
When BT coexistence is enabled (eg oper mode 13, which is the default)
the initialisation on startup sometimes silently fails.
In a normal initialisation we see
usb 1-1.3: Product: Wireless USB Network Module
usb 1-1.3: Manufacturer: Redpine Signals, Inc.
usb 1-1.3: SerialNumber: 000000000001
rsi_91x: rsi_probe: Initialized os intf ops
rsi_91x: rsi_load_9116_firmware: Loading chunk 0
rsi_91x: rsi_load_9116_firmware: Loading chunk 1
rsi_91x: rsi_load_9116_firmware: Loading chunk 2
rsi_91x: Max Stations Allowed = 1
But sometimes the last log is missing and the wlan net device is
not created.
Running a userspace loop that resets the hardware via a GPIO shows the
problem occurring ~5/100 resets.
The problem does not occur in oper mode 1 (wifi only).
Adding logs shows that the initialisation state machine requests a MAC
reset via rsi_send_reset_mac() but the firmware does not reply, leading
to the initialisation sequence being incomplete.
Fix this by delaying attaching the BT adapter until the wifi
initialisation has completed.
With this applied I have done > 300 reset loops with no errors.
Fixes: 716b840c7641 ("rsi: handle BT traffic in driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-2-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d6dbce453b19c64b96f3e927b10230f9a704b504 upstream.
Firmware sends delete_sta_context_ind when it detects the AP has gone
away in STA mode. Right now the handler for that indication only handles
AP mode; fix it to also handle STA mode.
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210901180606.11686-1-benl@squareup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8e3e59c31fea5de95ffc52c46f0c562c39f20c59 upstream.
It seems that the PCIe+USB firmware (latest version 15.68.19.p21) of the
88W8897 card sometimes ignores or misses when we try to wake it up by
writing to the firmware status register. This leads to the firmware
wakeup timeout expiring and the driver resetting the card because we
assume the firmware has hung up or crashed.
Turns out that the firmware actually didn't hang up, but simply "missed"
our wakeup request and didn't send us an interrupt with an AWAKE event.
Trying again to read the firmware status register after a short timeout
usually makes the firmware wake up as expected, so add a small retry
loop to mwifiex_pm_wakeup_card() that looks at the interrupt status to
check whether the card woke up.
The number of tries and timeout lengths for this were determined
experimentally: The firmware usually takes about 500 us to wake up
after we attempt to read the status register. In some cases where the
firmware is very busy (for example while doing a bluetooth scan) it
might even miss our requests for multiple milliseconds, which is why
after 15 tries the waiting time gets increased to 10 ms. The maximum
number of tries it took to wake the firmware when testing this was
around 20, so a maximum number of 50 tries should give us plenty of
safety margin.
Here's a reproducer for those firmware wakeup failures I've found:
1) Make sure wifi powersaving is enabled (iw dev wlp1s0 set power_save on)
2) Connect to any wifi network (makes firmware go into wifi powersaving
mode, not deep sleep)
3) Make sure bluetooth is turned off (to ensure the firmware actually
enters powersave mode and doesn't keep the radio active doing bluetooth
stuff)
4) To confirm that wifi powersaving is entered ping a device on the LAN,
pings should be a few ms higher than without powersaving
5) Run "while true; do iwconfig; sleep 0.0001; done", this wakes and
suspends the firmware extremely often
6) Wait until things explode, for me it consistently takes <5 minutes
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-3-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e5f4eb8223aa740237cd463246a7debcddf4eda1 upstream.
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3fd2c95c1c13ec217d43ebef3c61cfa00a6cd37 upstream.
We observe unexpected connection drops with some APs due to
non-acked mac80211 generated null data frames (keep-alive).
After debugging and capture, we noticed that null frames are
submitted at standard data bitrate and that the given APs are
in trouble with that.
After setting the null frame bitrate to control bitrate, all
null frames are acked as expected and connection is maintained.
Not sure if it's a requirement of the specification, but it seems
the right thing to do anyway, null frames are mostly used for control
purpose (power-saving, keep-alive...), and submitting them with
a slower/simpler bitrate/modulation is more robust.
Cc: stable@vger.kernel.org
Fixes: 512b191d9652 ("wcn36xx: Fix TX data path")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634560399-15290-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a9e79b116cc4d0057e912be8f40b2c2e5bdc7c43 upstream.
This change fix the TX ack mechanism in various ways:
- For NO_ACK tagged packets, we don't need to wait for TX_ACK indication
and so are not subject to the single packet ack limitation. So we don't
have to stop the tx queue, and can call the tx status callback as soon
as DMA transfer has completed.
- Fix skb ownership/reference. Only start status indication timeout
once the DMA transfer has been completed. This avoids the skb to be
both referenced in the DMA tx ring and by the tx_ack_skb pointer,
preventing any use-after-free or double-free.
- This adds a sanity (paranoia?) check on the skb tx ack pointer.
- Resume TX queue if TX status tagged packet TX fails.
Cc: stable@vger.kernel.org
Fixes: fdf21cc37149 ("wcn36xx: Add TX ack support")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634567281-28997-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 960ae77f25631bbe4e3aafefe209b52e044baf31 upstream.
All wcn36xx controllers are supposed to support HT40 (and SGI40),
This doubles the maximum bitrate/throughput with compatible APs.
Tested with wcn3620 & wcn3680B.
Cc: stable@vger.kernel.org
Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634737133-22336-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b5cd1fd6043bbb7c5810067b5f93f3016bfd8a6f upstream.
When clearing all existing pending tx slots, mt76_tx_complete_skb needs to
be used to free the skbs, to ensure that they are cleared from the status
list as well.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2e9be536a213e838daed6ba42024dd68954ac061 upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 605bebe23bf6 ("[PATCH] Add rtl8187 wireless driver")
Cc: stable@vger.kernel.org # 2.6.23
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025120522.6045-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a006acb931317aad3a8dd41333ebb0453caf49b8 upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4db66499df91 ("ath10k: add initial USB support")
Cc: stable@vger.kernel.org # 4.14
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5286132324230168d3fab6ffc16bfd7de85bdfb4 upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 4db66499df91 ("ath10k: add initial USB support")
Cc: stable@vger.kernel.org # 4.14
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025120522.6045-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a066d28a7e729f808a3e6eff22e70c003091544e upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 241b128b6b69 ("ath6kl: add back beginnings of USB support")
Cc: stable@vger.kernel.org # 3.4
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025120522.6045-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c1b9ca365deae667192be9fe24db244919971234 upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 9cbee358687e ("ath6kl: add full USB support")
Cc: stable@vger.kernel.org # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89f8765a11d8df49296d92c404067f9b5c58ee26 upstream.
Add the missing endpoint sanity checks to probe() to avoid division by
zero in mwifiex_write_data_sync() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Only add checks for the firmware-download boot stage, which require both
command endpoints, for now. The driver looks like it will handle a
missing endpoint during normal operation without oopsing, albeit not
very gracefully as it will try to submit URBs to the default pipe and
fail.
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4daffe354366 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: stable@vger.kernel.org # 3.5
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 541fd20c3ce5b0bc39f0c6a52414b6b92416831c upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Use the common control-message timeout define for the five-second
timeout.
Fixes: dad0d04fa7ba ("rsi: Add RS9113 wireless driver")
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025120522.6045-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 285bb1738e196507bf985574d0bc1e9dd72d46b1 upstream.
This reverts commit c6522a5076e1a65877c51cfee313a74ef61cabf8.
Testing on tip-of-tree shows that this is working now. Revert this and
re-enable BMPS for Open APs.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211022140447.2846248-3-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
|
|
Now that SCM can be a loadable module, we have to add another
dependency to avoid link failures when ipa or adreno-gpu are
built-in:
aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe':
ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available'
ld.lld: error: undefined symbol: qcom_scm_is_available
>>> referenced by adreno_gpu.c
>>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a
This can happen when CONFIG_ARCH_QCOM is disabled and we don't select
QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd
use a similar dependency here to what we have for QCOM_RPROC_COMMON,
but that causes dependency loops from other things selecting QCOM_SCM.
This appears to be an endless problem, so try something different this
time:
- CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on'
but that is simply selected by all of its users
- All the stubs in include/linux/qcom_scm.h can go away
- arm-smccc.h needs to provide a stub for __arm_smccc_smc() to
allow compile-testing QCOM_SCM on all architectures.
- To avoid a circular dependency chain involving RESET_CONTROLLER
and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement.
According to my testing this still builds fine, and the QCOM
platform selects this symbol already.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
wireless-drivers fixes for v5.15
Second set of fixes for v5.15, nothing major this time. Most important
here are reverting a brcmfmac regression and a fix for an old rare
ath5k build error.
iwlwifi
* fixes to NULL dereference, off by one and missing unlock
* add support for Killer AX1650 on Dell XPS 15 (9510) laptop
ath5k
* build fix with LEDS=m
brcmfmac
* revert a regression causing BCM4359/9 devices stop working as access point
mwifiex
* fix clang warning about null pointer arithmetic
|
|
clang complains about some NULL pointer arithmetic in this driver:
drivers/net/wireless/marvell/mwifiex/sta_tx.c:65:59: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
pad = ((void *)skb->data - (sizeof(*local_tx_pd) + hroom)-
^
drivers/net/wireless/marvell/mwifiex/uap_txrx.c:478:53: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
pad = ((void *)skb->data - (sizeof(*txpd) + hroom) - NULL) &
Rework that expression to do the same thing using a uintptr_t.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210927121656.940304-1-arnd@kernel.org
|
