summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/iwlwifi
AgeCommit message (Collapse)AuthorFilesLines
2015-02-01iwlwifi: mvm: always use mac color zeroLuciano Coelho1-3/+0
We don't really need to use different mac colors when adding mac contexts, because they're not used anywhere. In fact, the firmware doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401 when we reach that. Remove the color increment to use always zero and avoid reaching 255. CC: <stable@vger.kernel.org> [3.10+] Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-02-01iwlwifi: mvm: remove space padding after sysassert descriptionJohannes Berg1-1/+1
There's really no reason to pad out the field with spaces at the end of the line - they're practically invisible there anyway. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-02-01iwlwifi: mvm: don't reprobe if we fail during reconfig and fw_restart is falseLuciano Coelho1-5/+5
If we don't want to restart the firmware, don't reprobe either in case of a failure during reconfiguration. This allows us to debug failures in the reconfig flow as well. Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-25iwlwifi: mvm: check IWL_UCODE_TLV_API_SCD_CFG in API and not in capaEmmanuel Grumbach1-1/+1
IWL_UCODE_TLV_API_SCD_CFG is a new API and hence, check if enabled in the correct field. Fixes: 0294d9eece86 ("iwlwifi: mvm: let the firmware configure the scheduler") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: fix rx chains configuration in phy ctxt cmdLiad Kaufman1-1/+1
In the PHY_CTXT command sent to the FW the TX chains were indeed configured by the values of both FW TLVs and of NVM, but the RX chains were left out and configured only by FW TLV. This causes problems in 4165 HW, where there are 1x1 antennas, and the wrong configuration denies the driver from connecting to the AP. Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: pcie: support secured boot flow for family 8000 B stepEran Harary1-3/+5
The driver loads the 2 CPU sections, then it needs to let the firmware know to start the authentication of the sections. This is done by writing the relevants bits to FH_UCODE_LOAD_STATUS. For CPU1, the driver sets the lower 16 bits. For both CPUs, the driver sets all the 32 bits. Signed-off-by: Eran Harary <eran.harary@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: rs: remove stats argument from functionsJohannes Berg3-26/+72
The stats argument is always only passed as &mvm->drv_rx_stats, so there's no point in passing it when the mvm pointer is passed. Remove the argument entirely. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: use a new API for enabling STBCEyal Shapira3-3/+28
The new API tells the FW that it's allowed to use STBC but the FW will decide on its own whether to use STBC or SISO (and in the future Beamformer). Keep support for the old API which sets STBC explicitly in the rates in the LQ table while we still support old FW revisions. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: rs: refactor ht/vht initEyal Shapira1-38/+4
Prepare to add some more code there so refactor to separate functions. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: really disable TDLS queuesEmmanuel Grumbach1-2/+2
for_each_set_bit expect the size in number of bits and not in bytes. Fixes: a0f6bf2a5b01 ("iwlwifi: mvm: use private TFD queues for TDLS stations") Reviewed-by: Arik Nemtsov <arik@wizery.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: Do not consider invalid HW queues in queue maskIlan Peer1-2/+4
The iwl_mvm_mac_get_queues_mask() added vif->hw_queue[ac] to the queue mask although it might be set to IEEE80211_INVAL_HW_QUEUE. Fix it. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: BT Coex - set all the co-running values to 0Emmanuel Grumbach2-16/+16
With this value, we de-facto disable the feature. Since it is not working yet, disable it completely. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: support family 8000 C stepEran Harary3-2/+3
C step functionality in the driver is exactly the same as B step besides the ucode name that present as iwlwifi-8000C-xx.ucode instead of iwlwifi-8000B-xx.ucode Signed-off-by: Eran Harary <eran.harary@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: pcie: init ref_lockJohannes Berg1-0/+1
The ref_lock that was recently added is missing initialization which makes lockdep unhappy and is generally a bad idea. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: document switch case fall-through in iwl_mvm_send_sta_keyJohn W. Linville1-0/+1
Add a comment indicating that the WLAN_CIPHER_SUITE_WEP104 case falls through to the WLAN_CIPHER_SUITE_WEP40 case in iwl_mvm_send_sta_key. This will document that the lack of a break is intentional. Coverity: CID 1260023 Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: rs: use STBC regardless of power save modeEyal Shapira1-8/+0
Tx STBC was used only when in CAM mode or if powersave is disabled. Effectively this meant we never used STBC as these modes aren't used on most platforms by default. Change that. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22Revert "iwlwifi: mvm: drop non VO frames when flushing"Emmanuel Grumbach1-9/+11
This is now implemented by mac80211 (commit below). mac80211 will flush/drop the frames on the queues before suspending / disconnecting. It will then send the deauth and wait until the queues are empty. commit 3b24f4c65386dc0f2efb41027bc6e410ea2c0049 Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Date: Wed Jan 7 15:42:39 2015 +0200 mac80211: let flush() drop packets when possible This reverts commit 4e6c48e0984e28d064ee8fbc292aee7b7920c507.
2015-01-22iwlwifi: mvm: add support for new LTR commandEmmanuel Grumbach3-9/+51
This new command will give finer granularity to configure the platform. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: BT Coex - fine tune the MPLUT registerEmmanuel Grumbach1-1/+1
This allow to better preserve the BT performance while WiFi is running. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22Merge remote-tracking branch 'iwlwifi-fixes/master' into iwlwifi-nextEmmanuel Grumbach12-46/+112
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Conflicts: drivers/net/wireless/iwlwifi/iwl-fw-file.h drivers/net/wireless/iwlwifi/mvm/scan.c
2015-01-22iwlwifi: mvm: move U-APSD decision to authenticationJohannes Berg2-5/+16
In order to change the usage of U-APSD on the fly later, move the enabling condition into a new function that is called when authenticated. This allows the module parameter to become writable, it won't take effect immediately but at least on the next association the new value will be used. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22Merge tag 'tags/mac80211-next-for-davem-2015-01-19' into iwlwifi-nextEmmanuel Grumbach1-7/+6
Some further updates for net-next: * fix network-manager which was broken by the previous changes * fix delete-station events, which were broken by me making the genlmsg_end() mistake * fix a timer left running during suspend in some race conditions that would cause an annoying (but harmless) warning * (less important, but in the tree already) remove 80+80 MHz rate reporting since the spec doesn't distinguish it from 160 MHz; as the bitrate they're both 160 MHz bandwidth
2015-01-22iwlwifi: mvm: ignore temperature updates in the RX statistics notificationLuciano Coelho2-1/+7
If the firmware sends spontaneous DTS notfications with the temperature (indicated in a TLV), we can ignore the temperature we get in the RX statistics notifications. This prevents potentially handling the same temperature change twice. It also ignores notifications with temperature equal to 0 that happens from time to time. Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: rs: cleanup unuseful and overflowing tracesEyal Shapira1-3/+1
These aren't useful and overflowing so drop them and also fix a minor typo. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: generate statistics debugfs codeJohannes Berg2-86/+78
There's no need to duplicate the structure field name in the string, just generate the string in the macro that's there anyway. To keep the debugfs output the same, rename one (otherwise unused) field. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: move statistics API to new header fileJohannes Berg2-208/+278
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: sync statistics firmware APIJohannes Berg2-37/+37
The firmware API structs are split differently, synchronize the struct splits with the current firmware definitions. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: correctly set the NMI registerEmmanuel Grumbach2-4/+9
When we want to trigger an NMI in the device, we need to set bit 7 and not bit 0. However, older firmwares don't register to the interrupt issued by bit 7. Use bit 7 first so that the correct interrupt will be issued hoping that the firmware will react. To be on the safe side, set bit 0 in case the firmware didn't register to the proper interrupt. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: add rxf and txf to dump dataLiad Kaufman7-27/+304
When the FW is in error status - try to read the RXF and TXF (all of them) and add them to the dump data. This shouldn't happen in non-error statuses, as we don't want to stop the RXF/TXF while they are running. Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: add support for dumping a secondary SRAMIdo Yariv3-4/+32
Some HW modules have two SRAMs. In such cases add the secondary SRAM to the list of dumped segments. Signed-off-by: Ido Yariv <idox.yariv@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: add debugfs file for misbehaving U-APSD APJohannes Berg1-0/+31
As this functionality relies on getting a firmware notification it is difficult to test. Allow accessing the data for it from debugfs to be able to trigger all kinds of scenarios to test. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: let the firmware configure the schedulerEmmanuel Grumbach9-107/+97
A new host command can be used to configure the scheduler instead of accessing the scheduler's registers from the driver. This is easier and less error prone since accessing the hardware at certain moments can lead to races with the firmware. Prefer to use the host command whenever it is available. Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: scan dwell time correctionsDavid Spinadel2-5/+16
Use only basic dwell time (10 ms for active scan and 110 for passive), regardless of the number of the probes and the band, if it is supported by the FW. The FW will add 3 ms for each probe sent and 10 ms for low band channels. Add a TLV flag to indicate such support in FW. This fix is needed to fix few bugs regarding scans that take too much time. Signed-off-by: David Spinadel <david.spinadel@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: remove unused TLV capability flagsEmmanuel Grumbach1-6/+0
The driver doesn't support the firmwares that don't have these capabilities. The code that actually used these flags has been removed already, but the flags were left for an unclear reason. Remove them. Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: add print of he nvm versionEran Harary1-0/+2
Print the nvm version in the log for debugging purposes. Signed-off-by: Eran Harary <eran.harary@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: set max_out_time equal to frag_passive_dwell in fragmented scanHaim Dreyfuss1-2/+2
Fragmented scan should be applied for all channels, passive and active. When scanning on passive channels the firmware uses frag_passive_dwell to define the maximum continuous scan time before returning to the operating channel. On active channels max_out_time is the parameter used by the firmware to define the maximum time allowed out of the operating channel. Since active channels' scan should also be fragmented set max_out_time equal to frag_passive_dwell. In addition: - Set max_out_time and suspend_time if the firmware doesn't support fragmented scan to avoid unexpected behavior. - Adjust max_out_time for second level of scan precedence. Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Reviewed-by: Alexander Bondar <alexander.bondar@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: rs: allow to disable MIMO for P2P onlyEmmanuel Grumbach2-2/+2
This is to work around interoperability bugs with devices that don't hanle MIMO properly. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: allow to collect debug data from non-sleepable contextEmmanuel Grumbach2-7/+7
iwl_mvm_fw_dbg_collect allows to collect debug data from the firmware. Most of the firmware interaction is done in non-sleepable context. It makes little sense to force the caller of iwl_mvm_fw_dbg_collect to sleep. Defer the actual collection to a worker so that this function will be able to be called from any context. Reviewed-by: Eran Harary <eran.harary@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: make sure state isn't in d0i3 when stopping fw monitorLiad Kaufman1-2/+7
In case platform is in d0i3 - make sure it is awake when writing the registers to stop the monitor when collecting FW debug data. Plus, remove unneeded mutex locking currently done. Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: Add debugfs entry to enable scan offload notificationAlexander Bondar4-0/+48
This option enables scan offload iteration complete notification from firmware which includes the last iteration's status and the scanned channels from the current iteration. Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: add new config and PCI IDs for 4165 seriesOren Givon3-0/+13
Add a new config for 4165 series over PCI and insert support for two new 4165 series PCI IDs. Signed-off-by: Oren Givon <oren.givon@intel.com> Reviewed-by: Liad Kaufman <liad.kaufman@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: make sure state isn't in d0i3 when collecting fw dbgLiad Kaufman3-0/+7
This makes sure that we're not trying to read/write any of the FW debug data collected during d0i3. Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Reviewed-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: rs: repeat initial legacy rates in LQ tableEyal Shapira2-11/+13
Repeating the legacy rates avoids degrading quickly to lower rates due to collisions which is common when doing TCP Tx traffic in legacy. This slightly improves TCP Tx throughput while working in legacy in different scenarios. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-22iwlwifi: mvm: don't indicate no BA if STA was in powersaveEyal Shapira1-1/+2
If Tx failed because the STA was in powersave there's no point in sending a BAR so avoid indicating AMPDU_NO_BACK to mac80211. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-20iwlwifi: mvm: validate tid and sta_id in ba_notifEyal Shapira1-0/+5
These are coming from the FW and are used to access arrays. Bad values can cause an out of bounds access so discard such ba_notifs and warn. CC: <stable@vger.kernel.org> [3.10+] Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-18iwlwifi: mvm: abort scheduled scan upon RFKILLEmmanuel Grumbach1-0/+7
When we have an active scheduled scan, and the RFKILL interrupt kicks in, the stack will cancel the scheduled scan as part of the down flow. But cancelling scheduled scan usually implies sending a command to the firwmare which has been killed as part of the RFKILL interrupt handling. Because of that, we returned an error to mac80211 when it asked to stop the scheduled scan and didn't notify the end of the scheduled scan. Besides a fat warning, this led to a situation in which cfg80211 would refuse any new scan request. To disentangle this, fake that the scheduled scan has been stopped without sending the command to the firwmare, return 0 after having properly let cfg80211 know that the scan has been cancelled. This is basically the same as: commit 9b520d84957d63348e87c0f2cbd21d86e1e8f2f2 Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Date: Tue Nov 4 15:54:11 2014 +0200 iwlwifi: mvm: abort scan upon RFKILL This code existed but not for all the different FW APIs we support. Fix this. but for the scheduled scan case. Link: http://permalink.gmane.org/gmane.linux.kernel.wireless.general/133232 Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-13iwlwifi: mvm: set the tx cmd tid for BAR frame correctlyEyal Shapira1-2/+9
BAR tx cmd tid was set to non qos (8). This is wrong as BAR should be sent with the tid of the BA session. This led to a corruption in the firmware. The visible effect of this from the driver side is the BA notification that comes back after the BAR. It was botched and led to the WARNING below. ------------[ cut here ]------------ WARNING: CPU: 2 PID: 17707 at /home/tester/workspace_hostap/iwlwifi/drivers/net/wireless/iwlwifi/mvm/tx.c:976 iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm]() Q 4500, tid 8, flow 65535 Modules linked in: iwlmvm(O) mac80211(O) iwlwifi(O) cfg80211(O) compat(O) netconsole configfs ctr ccm arc4 autofs4 microcode bnep rfcomm snd_hda_codec_hdmi snd_hda_codec_idt snd_hda_codec_generic snd_hda_intel joydev snd_hda_codec uvcvideo videobuf2_core snd_hwdep videodev snd_pcm videobuf2_vmalloc videobuf2_memops i915 snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device drm_kms_helper dell_wmi dell_laptop drm btusb bluetooth snd psmouse i2c_algo_bit sparse_keymap wmi soundcore 6lowpan_iphc dcdbas serio_raw video lpc_ich ppdev mac_hid parport_pc nfsd nfs_acl auth_rpcgss nfs fscache binfmt_misc lockd sunrpc lp parport msdos sdhci_pci sdhci mmc_core ahci libahci e1000e ptp pps_core [last unloaded: compat] CPU: 2 PID: 17707 Comm: irq/46-iwlwifi Tainted: G W O 3.14.17-patched #4 Hardware name: Dell Inc. Latitude E6430/0CPWYR, BIOS A09 12/13/2012 00000000 00000000 ebd49d6c c1616221 f985dbdc ebd49d9c c1044e44 f9861df4 ebd49dc8 0000452b f985dbdc 000003d0 f98395da f98395da ebd49f10 eaf3d8a4 0000ffff ebd49db4 c1044f03 00000009 ebd49dac f9861df4 ebd49dc8 ebd49e64 Call Trace: [<c1616221>] dump_stack+0x41/0x52 [<c1044e44>] warn_slowpath_common+0x84/0xa0 [<f98395da>] ? iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm] [<f98395da>] ? iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm] [<c1044f03>] warn_slowpath_fmt+0x33/0x40 [<f98395da>] iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm] [<c10e3952>] ? ring_buffer_unlock_commit+0xa2/0xd0 [<c10e9767>] ? trace_buffer_unlock_commit+0x37/0x50 [<f98568a3>] ? iwl_tm_mvm_send_rx+0x53/0x90 [iwlmvm] [<f98327a8>] iwl_mvm_rx_dispatch+0x108/0x130 [iwlmvm] [<f9eac7e7>] iwl_pcie_irq_handler+0xf17/0x15b0 [iwlwifi] [<c10994c1>] irq_thread_fn+0x21/0x50 [<c109926c>] irq_thread+0xec/0x110 [<c10994a0>] ? irq_thread_dtor+0xb0/0xb0 [<c10993f0>] ? irq_finalize_oneshot.part.34+0xc0/0xc0 [<c1099180>] ? wake_threads_waitq+0x40/0x40 [<c1062fdb>] kthread+0x9b/0xb0 [<c1627137>] ret_from_kernel_thread+0x1b/0x28 [<c1062f40>] ? flush_kthread_worker+0x90/0x90 ---[ end trace 5e0f67374816db17 ]--- Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-12iwlwifi: mvm: drop non VO frames when flushingEmmanuel Grumbach1-11/+9
This change has already been implemented in iwldvm: commit a260e7b3f0307878b99d57ed1406cf2d497923b8 Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Date: Sun Oct 5 09:11:14 2014 +0300 iwlwifi: dvm: drop non VO frames when flushing Since I added the flush() callback implementation in mvm, we got reports that the queues are stuck while roaming or suspending. This commit above helped much for iwldvm, implement the same behavior for iwlmvm. CC: <stable@vger.kernel.org> [3.16+] Fixes: c5b0e7c0565a ("iwlwifi: mvm: implement mac80211's flush callback") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-12iwlwifi: mvm: fix EBS on single scanDavid Spinadel3-14/+41
EBS error detection isn't supported by all FWs, so turn it on only if the FW advertises such support. Signed-off-by: David Spinadel <david.spinadel@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-01-05iwlwifi: bump firmware API for mvm devices to 12Emmanuel Grumbach2-3/+3
This allows 3160 / 7260 / 7265 / 7265D / 8000 devices to use the latest version of the firmware. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-13 00:56:22 +0300