summaryrefslogtreecommitdiff
path: root/drivers/net/phy
AgeCommit message (Collapse)AuthorFilesLines
2022-05-02net: phylink: Convert to mdiobus_c45_{read|write}Andrew Lunn1-15/+17
Stop using the helpers to construct a special phy address which indicates C45. Instead use the C45 accessors, which will call the busses C45 specific read/write API. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-05-01net: phy: adin1100: Add SQI supportAlexandru Tachici1-0/+52
Determine the SQI from MSE using a predefined table for the 10BASE-T1L. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-01net: phy: adin1100: Add initial support for ADIN1100 industrial PHYAlexandru Ardelean3-0/+248
The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for industrial Ethernet applications and is compliant with the IEEE 802.3cg Ethernet standard for long reach 10 Mb/s Single Pair Ethernet. Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-01net: phy: Add 10BASE-T1L support in phy-c45Alexandru Tachici2-5/+253
This patch is needed because the BASE-T1 uses different registers for status, control and advertisement to those already employed in the existing phy-c45 functions. Where required, genphy_c45 functions will now check whether the device supports BASE-T1 and use the specific registers instead: 45.2.7.19 BASE-T1 AN control register, 45.2.7.20 BASE-T1 AN status, 45.2.7.21 BASE-T1 AN advertisement register, 45.2.7.22 BASE-T1 AN LP Base Page ability register, 45.2.1.185 BASE-T1 PMA/PMD control register. Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-01ethtool: Add 10base-T1L link mode entryAlexandru Tachici3-3/+7
Add entry for the 10base-T1L full duplex mode. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-01net: phy: marvell: update abilities and advertising when switching to SGMIIRobert Hancock1-1/+15
With some SFP modules, such as Finisar FCLF8522P2BTL, the PHY hardware strapping defaults to 1000BaseX mode, but the kernel prefers to set them for SGMII mode. When this happens and the PHY is soft reset, the BMSR status register is updated, but this happens after the kernel has already read the PHY abilities during probing. This results in support not being detected for, and the PHY not advertising support for, 10 and 100 Mbps modes, preventing the link from working with a non-gigabit link partner. When the PHY is being configured for SGMII mode, call genphy_read_abilities again in order to re-read the capabilities, and update the advertising field accordingly. Signed-off-by: Robert Hancock <robert.hancock@calian.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-30net: phy: micrel: add coma mode GPIOMichael Walle1-0/+20
The LAN8814 has a coma mode pin which puts the PHY into isolate and power-dowm mode. Unfortunately, the mode cannot be disabled by a register. Usually, the input pin has a pull-up and connected to a GPIO which can then be used to disable the mode. Try to get the GPIO and deassert it. Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-30net: phy: micrel: move the PHY timestamping checkMichael Walle1-4/+8
Both lan8814_ptp_init() and lan8814_ptp_probe_once() are only used if PTP and PHY timestamping is enabed. Up until now the probe function just returns early, if they are not needed. But we need the phy_package_init_once() functionality for the coma mode GPIO setup. Move the check into the functions itself. Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-29net: phy: Deduplicate interrupt disablement on PHY attachLukas Wunner1-4/+2
phy_attach_direct() first calls phy_init_hw() (which restores interrupt settings through ->config_intr()), then calls phy_disable_interrupts(). So if phydev->interrupts was previously set to 1, interrupts are briefly enabled, then disabled, which seems nonsensical. If it was previously set to 0, interrupts are disabled twice, which is equally nonsensical. Deduplicate interrupt disablement. Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/805ccdc606bd8898d59931bd4c7c68537ed6e550.1651040826.git.lukas@wunner.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-28Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski1-1/+1
include/linux/netdevice.h net/core/dev.c 6510ea973d8d ("net: Use this_cpu_inc() to increment net->core_stats") 794c24e9921f ("net-core: rx_otherhost_dropped to core_stats") https://lore.kernel.org/all/20220428111903.5f4304e0@canb.auug.org.au/ drivers/net/wan/cosa.c d48fea8401cf ("net: cosa: fix error check return value of register_chrdev()") 89fbca3307d4 ("net: wan: remove support for COSA and SRP synchronous serial boards") https://lore.kernel.org/all/20220428112130.1f689e5e@canb.auug.org.au/ Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-26net: phy: marvell10g: fix return value on errorBaruch Siach1-1/+1
Return back the error value that we get from phy_read_mmd(). Fixes: c84786fa8f91 ("net: phy: marvell10g: read copper results from CSSR1") Signed-off-by: Baruch Siach <baruch.siach@siklu.com> Reviewed-by: Marek Behún <kabel@kernel.org> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/f47cb031aeae873bb008ba35001607304a171a20.1650868058.git.baruch@tkos.co.il Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-04-26net: phy: LAN937x: add interrupt support for link detectionArun Ramadoss1-0/+2
Added the config_intr and handle_interrupt for the LAN937x phy which is same as the LAN87xx phy. Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220423154727.29052-1-arun.ramadoss@microchip.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-04-23net: phy: LAN87xx: add ethtool SQI supportArun Ramadoss1-0/+48
This patch add the support for measuring Signal Quality Index for LAN87xx and LAN937x T1 Phy. It uses the SQI Method 5 for obtaining the values. Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netPaolo Abeni1-0/+1
drivers/net/ethernet/microchip/lan966x/lan966x_main.c d08ed852560e ("net: lan966x: Make sure to release ptp interrupt") c8349639324a ("net: lan966x: Add FDMA functionality") Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-04-15net: phy: LAN937x: added PHY_POLL_CABLE_TEST flagArun Ramadoss1-0/+1
Added the phy_poll_cable_test flag for the lan937x phy driver. Tested using command - ethtool --cable-test <dev> Fixes: 680baca546f2 ("net: phy: added the LAN937x phy support") Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netPaolo Abeni1-6/+1
2022-04-13net: phylink: remove phylink_helper_basex_speed()Russell King (Oracle)1-28/+0
As there are now no users of phylink_helper_basex_speed(), we can remove this obsolete functionality. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-11net: phy: LAN87xx: remove genphy_softreset in config_anegArun Ramadoss1-6/+1
When the T1 phy master/slave state is changed, at the end of config_aneg function genphy_softreset is called. After the reset all the registers configured during the config_init are restored to default value. To avoid this, removed the genphy_softreset call. v1->v2 ------ Added the author in cc Fixes: 8a1b415d70b7 ("net: phy: added ethtool master-slave configuration support") Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-09net: phy: micrel: ksz9031/ksz9131: add cabletest supportMarek Vasut1-0/+221
Add cable test support for Micrel KSZ9x31 PHYs. Tested on i.MX8M Mini with KSZ9131RNX in 100/Full mode with pairs shuffled before magnetics: (note: Cable test started/completed messages are omitted) mx8mm-ksz9131-a-d-connected$ ethtool --cable-test eth0 Pair A code OK Pair B code Short within Pair Pair B, fault length: 0.80m Pair C code Short within Pair Pair C, fault length: 0.80m Pair D code OK mx8mm-ksz9131-a-b-connected$ ethtool --cable-test eth0 Pair A code OK Pair B code OK Pair C code Short within Pair Pair C, fault length: 0.00m Pair D code Short within Pair Pair D, fault length: 0.00m Tested on R8A77951 Salvator-XS with KSZ9031RNX and all four pairs connected: (note: Cable test started/completed messages are omitted) r8a7795-ksz9031-all-connected$ ethtool --cable-test eth0 Pair A code OK Pair B code OK Pair C code OK Pair D code OK The CTRL1000 CTL1000_ENABLE_MASTER and CTL1000_AS_MASTER bits are not restored by calling phy_init_hw(), they must be manually cached in ksz9x31_cable_test_start() and restored at the end of ksz9x31_cable_test_get_status(). Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Oleksij Rempel <linux@rempel-privat.de> Cc: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20220407105534.85833-1-marex@denx.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-04net: phy: micrel: Remove DT option lan8814,ignore-tsHoratiu Vultur1-3/+1
When the PHY and the MAC are capable of doing timestamping, the PHY has priority. Therefore the DT option lan8814,ignore-ts was added such that the PHY will not expose a PHC so then the timestamping was done in the MAC. This is not the correct approach of doing it, therefore remove this. Fixes: ece19502834d84 ("net: phy: micrel: 1588 support for LAN8814 phy") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-04net: phy: micrel: Remove latency from driverHoratiu Vultur1-101/+1
Based on the discussions here[1], the PHY driver is the wrong place to set the latencies, therefore remove them. [1] https://lkml.org/lkml/2022/3/4/325 Fixes: ece19502834d84 ("net: phy: micrel: 1588 support for LAN8814 phy") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-26net: phy: broadcom: Fix brcm_fet_config_init()Florian Fainelli1-0/+21
A Broadcom AC201 PHY (same entry as 5241) would be flagged by the Broadcom UniMAC MDIO controller as not completing the turn around properly since the PHY expects 65 MDC clock cycles to complete a write cycle, and the MDIO controller was only sending 64 MDC clock cycles as determined by looking at a scope shot. This would make the subsequent read fail with the UniMAC MDIO controller command field having MDIO_READ_FAIL set and we would abort the brcm_fet_config_init() function and thus not probe the PHY at all. After issuing a software reset, wait for at least 1ms which is well above the 1us reset delay advertised by the datasheet and issue a dummy read to let the PHY turn around the line properly. This read specifically ignores -EIO which would be returned by MDIO controllers checking for the line being turned around. If we have a genuine reaad failure, the next read of the interrupt status register would pick it up anyway. Fixes: d7a2ed9248a3 ("broadcom: Add AC131 phy support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220324232438.1156812-1-f.fainelli@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-17Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2-4/+7
No conflicts. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-17net: phy: mscc: Add MODULE_FIRMWARE macrosJuerg Haefliger1-0/+3
The driver requires firmware so define MODULE_FIRMWARE so that modinfo provides the details. Fixes: fa164e40c53b ("net: phy: mscc: split the driver into separate files") Signed-off-by: Juerg Haefliger <juergh@canonical.com> Link: https://lore.kernel.org/r/20220316151835.88765-1-juergh@canonical.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-15net: phy: Kconfig: micrel_phy: fix dependency issueAnders Roxell1-0/+1
When building driver CONFIG_MICREL_PHY the follow error shows up: aarch64-linux-gnu-ld: drivers/net/phy/micrel.o: in function `lan8814_ts_info': micrel.c:(.text+0x1764): undefined reference to `ptp_clock_index' micrel.c:(.text+0x1764): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ptp_clock_index' aarch64-linux-gnu-ld: drivers/net/phy/micrel.o: in function `lan8814_probe': micrel.c:(.text+0x4720): undefined reference to `ptp_clock_register' micrel.c:(.text+0x4720): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ptp_clock_register' Rework Kconfig for MICREL_PHY to depend on 'PTP_1588_CLOCK_OPTIONAL'. Arnd describes in a good way why its needed to add this depends in patch e5f31552674e ("ethernet: fix PTP_1588_CLOCK dependencies"). Reported-by: kernel test robot <lkp@intel.com> Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy") Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220314110254.12498-1-anders.roxell@linaro.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-03-15net: sfp: add 2500base-X quirk for Lantech SFP moduleMichael Walle1-0/+6
The Lantech 8330-262D-E module is 2500base-X capable, but it reports the nominal bitrate as 2500MBd instead of 3125MBd. Add a quirk for the module. The following in an EEPROM dump of such a SFP with the serial number redacted: 00: 03 04 07 00 00 00 01 20 40 0c 05 01 19 00 00 00 ???...? @????... 10: 1e 0f 00 00 4c 61 6e 74 65 63 68 20 20 20 20 20 ??..Lantech 20: 20 20 20 20 00 00 00 00 38 33 33 30 2d 32 36 32 ....8330-262 30: 44 2d 45 20 20 20 20 20 56 31 2e 30 03 52 00 cb D-E V1.0?R.? 40: 00 1a 00 00 46 43 XX XX XX XX XX XX XX XX XX XX .?..FCXXXXXXXXXX 50: 20 20 20 20 32 32 30 32 31 34 20 20 68 b0 01 98 220214 h??? 60: 45 58 54 52 45 4d 45 4c 59 20 43 4f 4d 50 41 54 EXTREMELY COMPAT 70: 49 42 4c 45 20 20 20 20 20 20 20 20 20 20 20 20 IBLE Signed-off-by: Michael Walle <michael@walle.cc> Link: https://lore.kernel.org/r/20220312205014.4154907-1-michael@walle.cc Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-03-15net: phy: marvell: Fix invalid comparison in the resume and suspend functionsKurt Cancemi1-4/+4
This bug resulted in only the current mode being resumed and suspended when the PHY supported both fiber and copper modes and when the PHY only supported copper mode the fiber mode would incorrectly be attempted to be resumed and suspended. Fixes: 3758be3dc162 ("Marvell phy: add functions to suspend and resume both interfaces: fiber and copper links.") Signed-off-by: Kurt Cancemi <kurt@x64architecture.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220312201512.326047-1-kurt@x64architecture.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2-12/+21
net/dsa/dsa2.c commit afb3cc1a397d ("net: dsa: unlock the rtnl_mutex when dsa_master_setup() fails") commit e83d56537859 ("net: dsa: replay master state events in dsa_tree_{setup,teardown}_master") https://lore.kernel.org/all/20220307101436.7ae87da0@canb.auug.org.au/ drivers/net/ethernet/intel/ice/ice.h commit 97b0129146b1 ("ice: Fix error with handling of bonding MTU") commit 43113ff73453 ("ice: add TTY for GNSS module for E810T device") https://lore.kernel.org/all/20220310112843.3233bcf1@canb.auug.org.au/ drivers/staging/gdm724x/gdm_lte.c commit fc7f750dc9d1 ("staging: gdm724x: fix use after free in gdm_lte_rx()") commit 4bcc4249b4cf ("staging: Use netif_rx().") https://lore.kernel.org/all/20220308111043.1018a59d@canb.auug.org.au/ Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-11net: phy: meson-gxl: improve link-up behaviorHeiner Kallweit1-1/+7
Sometimes the link comes up but no data flows. This patch fixes this behavior. It's not clear what's the root cause of the issue. According to the tests one other link-up issue remains. In very rare cases the link isn't even reported as up. Fixes: 84c8f773d2dc ("net: phy: meson-gxl: remove the use of .ack_callback()") Tested-by: Erico Nunes <nunes.erico@gmail.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/e3473452-a1f9-efcf-5fdd-02b6f44c3fcd@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-10net: phy: DP83822: clear MISR2 register to disable interruptsClément Léger1-1/+1
MISR1 was cleared twice but the original author intention was probably to clear MISR1 & MISR2 to completely disable interrupts. Fix it to clear MISR2. Fixes: 87461f7a58ab ("net: phy: DP83822 initial driver submission") Signed-off-by: Clément Léger <clement.leger@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220309142228.761153-1-clement.leger@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-08net: phy: lan87xx: use genphy_read_master_slave in read_statusArun Ramadoss1-29/+1
To read the master slave configuration of the LAN87xx T1 phy, used the generic phy driver genphy_read_master_slave function. Removed the local lan87xx_read_master_slave function. Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-03-08net: phy: exported the genphy_read_master_slave functionArun Ramadoss1-10/+9
genphy_read_master_slave function allows to configure the master/slave for gigabit phys only. In order to use this function irrespective of speed, moved the speed check to the genphy_read_status call. Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-03-07net: phy: micrel: Move netif_rx() outside of IRQ-off section.Sebastian Andrzej Siewior1-2/+2
lan8814_match_rx_ts() invokes netif_rx() with disables interrupts outside which will create a warning. Invoking netif_rx_ni() with disabled interrupts is wrong even without the recent rework because netif_rx_ni() would enable interrupts while processing the softirq. This in turn can lead to dead lock if an interrupts triggers and attempts to acquire kszphy_ptp_priv::rx_ts_lock. Move netif_rx() outside the IRQ-off section. Cc: Andrew Lunn <andrew@lunn.ch> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Divya Koppera <Divya.Koppera@microchip.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-07net: phy: micrel: Use netif_rx().Sebastian Andrzej Siewior1-2/+2
Since commit baebdf48c3600 ("net: dev: Makes sure netif_rx() can be invoked in any context.") the function netif_rx() can be used in preemptible/thread context as well as in interrupt context. Use netif_rx(). Cc: Andrew Lunn <andrew@lunn.ch> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Divya Koppera <Divya.Koppera@microchip.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-07micrel: Use generic ptp_msg_is_sync() functionKurt Kanzenbach1-12/+1
Use generic ptp_msg_is_sync() function to avoid code duplication. Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-07dp83640: Use generic ptp_msg_is_sync() functionKurt Kanzenbach1-12/+1
Use generic ptp_msg_is_sync() function to avoid code duplication. Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-06net: phy: Use netif_rx().Sebastian Andrzej Siewior3-5/+5
Since commit baebdf48c3600 ("net: dev: Makes sure netif_rx() can be invoked in any context.") the function netif_rx() can be used in preemptible/thread context as well as in interrupt context. Use netif_rx(). Cc: Andrew Lunn <andrew@lunn.ch> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Radu Pirea <radu-nicolae.pirea@oss.nxp.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Russell King <linux@armlinux.org.uk> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-05net: phy: meson-gxl: fix interrupt handling in forced modeHeiner Kallweit1-10/+13
This PHY doesn't support a link-up interrupt source. If aneg is enabled we use the "aneg complete" interrupt for this purpose, but if aneg is disabled link-up isn't signaled currently. According to a vendor driver there's an additional "energy detect" interrupt source that can be used to signal link-up if aneg is disabled. We can safely ignore this interrupt source if aneg is enabled. This patch was tested on a TX3 Mini TV box with S905W (even though boot message says it's a S905D). This issue has been existing longer, but due to changes in phylib and the driver the patch applies only from the commit marked as fixed. Fixes: 84c8f773d2dc ("net: phy: meson-gxl: remove the use of .ack_callback()") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/04cac530-ea1b-850e-6cfa-144a55c4d75d@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-04net: phy: added ethtool master-slave configuration supportArun Ramadoss1-0/+90
To configure the T1 phy as master or slave using the ethtool -s <dev> master-slave <forced-master/forced-slave>, the config_aneg and read status functions are added. Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com> Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-04net: phy: added the LAN937x phy supportArun Ramadoss1-1/+54
LAN937x T1 switch is based on LAN87xx Phy, so reusing the init script of the LAN87xx. There is a workaround in accessing the DSP bank register for LAN937x Phy. Whenever there is a bank switch to DSP registers, then we need a one dummy read access before proceeding to the actual register access. Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com> Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-04net: phy: updated the initialization routine for LAN87xxArun Ramadoss1-42/+175
The new initialization sequence is the improvement to the existing init routine. Init routine does soft reset, run init script and set Hw_init. Added the new access_smi_poll_timeout() for polling smi bank write. Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com> Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-04net: phy: removed empty lines in LAN87XXArun Ramadoss1-4/+0
Removed the empty lines in struct phy_drivers. Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-04net: phy: used the PHY_ID_MATCH_MODEL macro for LAN87XXArun Ramadoss1-3/+4
Used the PHY_ID_MATCH_MODEL MACRO for describing the phy_id and phy_id_mask. Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-04net: phy: used genphy_soft_reset for phy reset in LAN87xxArun Ramadoss1-12/+2
Replaced the current code of resetting of LAN87xx phy to genphy_soft_reset library function. Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-04net: phy: micrel: 1588 support for LAN8814 phyDivya Koppera1-22/+1066
Add support for 1588 in LAN8814 phy driver. It supports 1-step and 2-step timestamping. Co-developed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-04net: phy: micrel: Fix concurrent register accessDivya Koppera1-14/+16
Make Extended page register accessing atomic, to overcome unexpected output from register reads/writes. Fixes: 7c2dcfa295b1 ("net: phy: micrel: Add support for LAN8804 PHY") Signed-off-by: Divya Koppera<Divya.Koppera@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-03-03net: sfp: use %pe for printing errorsRussell King (Oracle)1-18/+30
Convert sfp to use %pe for printing error codes, which can print them as errno symbols rather than numbers. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/E1nOyEN-00BuuE-OB@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-03net: phylink: use %pe for printing errorsRussell King (Oracle)1-9/+11
Convert phylink to use %pe for printing error codes, which can print them as errno symbols rather than numbers. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/E1nOyEI-00Buu8-K9@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-28Merge tag 'spi-remove-void' of ↵Jakub Kicinski1-3/+1
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi Mark Brown says: ==================== spi: Make remove() return void This series from Uwe Kleine-König converts the spi remove function to return void since there is nothing useful that we can do with a failure and it as more buses are converted it'll enable further work on the driver core. ==================== Link: https://lore.kernel.org/r/20220228173957.1262628-2-broonie@kernel.org/ Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-28net: phylink: remove phylink_set_pcs()Russell King (Oracle)1-32/+12
As all users of phylink_set_pcs() have now been updated to use the mac_select_pcs() method, it can be removed from the phylink kernel API and its functionality moved into phylink_major_config(). Removing phylink_set_pcs() gives us a single approach for attaching a PCS within phylink. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-27 07:13:24 +0300