summaryrefslogtreecommitdiff
path: root/drivers/net/phy
AgeCommit message (Collapse)AuthorFilesLines
2016-01-18net: phy: at803x: Add the interrupt register bit definitionsMartin Blumenstingl1-9/+23
Also use them instead of a magic value when enabling the interrupts. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-18net: phy: at803x: Clean up duplicate register definitionsMartin Blumenstingl1-8/+11
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-18net: phy: at803x: Allow specifying the RGMII RX clock delay via phy modeMartin Blumenstingl1-9/+54
at803x currently automatically enables the RGMII TX clock delay when the phy interface mode is PHY_INTERFACE_MODE_RGMII_TXID. The same should be done when PHY_INTERFACE_MODE_RGMII_ID is specified. Use a similar logic to enable the RGMII RX clock delay as well. at803x_context_{save,restore} were not touched because these are only used on AR8030 which is a RMII phy (RGMII clock delays are irrelevant). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-18net: phy: at803x: Don't set gbit features for the AR8030 phyMartin Blumenstingl1-1/+1
The 8030 is only a "RMII Fast Ethernet PHY", thus it must not have the SUPPORTED_1000* bits set. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-15net: phy: turn carrier off on phy attachSjoerd Simons1-0/+5
The operstate of a networking device initially IF_OPER_UNKNOWN aka "unknown", updated on carrier state changes (with carrier state being on by default). This means it will stay unknown unless the carrier state goes to off at some point, which is not the case if the phy is already up/connected at startup. Explicitly turn off the carrier on phy attach, leaving the phy state machine to turn the carrier on when it has done the initial negotiation. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-12phy: remove an unneeded conditionDan Carpenter1-1/+1
It used to be that bus->irq was a pointer but after e7f4dc3536a4 ('mdio: Move allocation of interrupts into core') it's an array inside the mdio struct, so it can never be NULL. Let's remove the check. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-12mdio_bus: NULL dereference on allocation errorDan Carpenter1-5/+6
If bus = kzalloc() fails then we end up dereferencing bus when we do "bus->irq[i] = PHY_POLL;". The code is a little simpler if we reverse the NULL check and return directly on failure. Fixes: e7f4dc3536a4 ('mdio: Move allocation of interrupts into core') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-12Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-2/+10
Conflicts: drivers/net/bonding/bond_main.c drivers/net/ethernet/mellanox/mlxsw/spectrum.h drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c The bond_main.c and mellanox switch conflicts were cases of overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-11net: phy: Add support for SMSC LAN8740 PHYJoshua Henderson1-0/+22
LAN8740 has a different phy_id than LAN8710/LAN8720. Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-09phy: micrel: Fix finding PHY properties in MAC node for KSZ9031.Roosen Henri1-2/+10
Commit 651df2183543 ("phy: micrel: Fix finding PHY properties in MAC node.") only fixes finding PHY properties in MAC node for KSZ9021. This commit applies the same fix for KSZ9031. Fixes: 8b63ec1837fa ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.") Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Henri Roosen <henri.roosen@ginzinger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07mdio: Abstract device_remove() and device_free()Andrew Lunn3-14/+29
Make device_free and device_remove operations in the mdio device structure, so the core code does not need to differentiate between phy devices and generic mdio devices. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07mdio: Add support for mdio drivers.Andrew Lunn4-13/+198
Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers are PHY drivers. Add support for generic MDIO drivers. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07mdio_bus: Add comment to mdiobus_scan() and __mdiobus_register()Andrew Lunn1-1/+15
Make it clear that mdiobus_scan () will only find devices which have a vendor/product ID in registers 2 and 3. These are typically PHY devices. Other sort of MDIO devices, such as switches, are not expected to be found during the scan. Similarly, __mdiobus_register(), which calls mdiobus_scan() will only find PHY devices, and other sorts of MDIO devices are expected to be instantiated from device tree. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07mdio_bus: Generalise of_mdiobus_link_phydev()Andrew Lunn1-14/+15
This function should work with any sort of MDIO device which can be probed on the bus, not just PHY devices. So generalise it. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07phy: Move phy specific bus match into phy_deviceAndrew Lunn2-26/+40
Matching a driver to a device has both generic parts, and parts which are specific to PHY devices. Move the PHY specific parts into phy_device. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07phy: Centralize setting driver module ownerAndrew Lunn26-118/+8
Rather than have each driver set the driver owner field, do it once in the core code. This will also help with later changes, when the device structure will move. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07phy: Move PHY PM operations into phy_deviceAndrew Lunn2-73/+120
The MDIO PM operations are really PHY device PM operations. So move them into phy_device. This will be needed when we support devices on the mdio bus which are not PHYs. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07phy_device: Move phy attributes into phy_deviceAndrew Lunn2-42/+44
The mdio_bus exports three attributes: - PHY ID is the unique 32-bits identifier for a MDIO device implementing standard MII registers MII_PHYSID1/2, which is not guaranteed to be the case for non-standard compliant devices (e.g: Ethernet switches) - PHY interface describes the data-path of the PHY/MDIO device, which is not strictly a PHY thing, but is required and needed for PHY devices to function, a MDIO device could be a control device exclusively - PHY has fixups describes what the PHY driver may have done, so completely PHY specific These are all phy attributes, not generic mdio attributes. So move the attributes into the phy device code. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07phy: Add API for {un}registering an mdio device to a bus.Andrew Lunn2-13/+54
Rather than have drivers directly manipulate the mii_bus structure, provide and API for registering and unregistering devices on an MDIO bus, and performing lookups. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07phy: Add an mdio_device structureAndrew Lunn13-89/+95
Not all devices attached to an MDIO bus are phys. So add an mdio_device structure to represent the generic parts of an mdio device, and place this structure into the phy_device. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07mdio: Move allocation of interrupts into coreAndrew Lunn8-36/+10
Have mdio_alloc() create the array of interrupt numbers, and initialize it to POLLING. This is what most MDIO drivers want, so allowing code to be removed from the drivers. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07phy: mdio-octeon: Use devm_mdiobus_alloc_size()Andrew Lunn1-7/+5
Rather than use devm_kzalloc(), use the mdio helper function. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07phy: Centralise print about attached phyAndrew Lunn1-0/+27
Many Ethernet drivers contain the same netdev_info() print statement about the attached phy. Move it into the phy device code. Additionally add a varargs function which can be used to append additional information. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07phy: phy_{read|write}_mmd_indirect: get addr from phydevAndrew Lunn4-32/+23
The address of the device can be determined from the phydev structure, rather than passing it as a parameter. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07phy: add phydev_name() wrapperAndrew Lunn2-2/+2
Add a phydev_name() function, to help with moving some structure members from phy_device. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07phy: Add phydev_err() and phydev_dbg() macrosAndrew Lunn4-13/+17
In preparation for moving some of the phy_device structure members, add macros for printing errors and debug information. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-31phy: micrel: Add ethtool statistics countersAndrew Lunn1-0/+96
The PHY counters receiver errors and errors while idle. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-31phy: marvell: Add ethtool statistics countersAndrew Lunn1-0/+135
The PHY counters receiver errors and errors while idle. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-18Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2-3/+17
Conflicts: drivers/net/geneve.c Here we had an overlapping change, where in 'net' the extraneous stats bump was being removed whilst in 'net-next' the final argument to udp_tunnel6_xmit_skb() was being changed. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-14net: phy: mdio-mux: Check return value of mdiobus_alloc()Tobias Klauser1-1/+6
mdiobus_alloc() might return NULL, but its return value is not checked in mdio_mux_init(). This could potentially lead to a NULL pointer dereference. Fix it by checking the return value Fixes: 0ca2997d1452 ("netdev/of/phy: Add MDIO bus multiplexer support.") Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-12phy: micrel: Fix finding PHY properties in MAC node.Andrew Lunn1-2/+11
commit 8b63ec1837fa ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.") changed the parenting of PHY devices, making them a child of the MDIO bus, instead of the MAC device. This broken the Micrel PHY driver which has a deprecated feature of allowing PHY properties to be placed into the MAC node. In order to find the MAC node, we need to walk up the tree of devices until we find one with an OF node attached. Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com> Suggested-by: David Daney <david.daney@cavium.com> Acked-by: David Daney <david.daney@cavium.com> Fixes: 8b63ec1837fa ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-07PHY: DP83867: Remove looking in parent device for OF propertiesAndrew Lunn1-4/+1
Device tree properties for a phy device are expected to be in the phy node. The current code for the DP83867 also tries to look in the parent node. The devices binding documentation does not mention this, no current device tree file makes use of this, and it is not behaviour we want. So remove looking in the parent device. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2-2/+3
Conflicts: drivers/net/ethernet/renesas/ravb_main.c kernel/bpf/syscall.c net/ipv4/ipmr.c All three conflicts were cases of overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-03net: phy: reset only targeted phyJérôme Pouiller1-1/+2
It is possible to address another chip on same MDIO bus. The case is correctly handled for media advertising. It is taken into account only if mii_data->phy_id == phydev->addr. However, this condition was missing for reset case. Signed-off-by: Jérôme Pouiller <jezz@sysmic.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-25net: phy: bcm7xxx: Add entry for Broadcom BCM7435Florian Fainelli1-0/+14
Add a PHY entry for the Broadcom BCM7435 chips, this is a 40nm generation Ethernet PHY which is analogous to its 7425 and 7429 counter parts. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-24broadcom: fix PHY_ID_BCM5481 entry in the id tableAaro Koskinen1-1/+1
Commit fcb26ec5b18d ("broadcom: move all PHY_ID's to header") updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0 with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting the original). Fix that. Fixes: fcb26ec5b18d ("broadcom: move all PHY_ID's to header") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-17net: phy: Use interrupts when available in NOLINK stateAndrew Lunn1-0/+3
The NOLINK state will poll the phy once a second to see if the link has come up. If the phy has an interrupt line, this polling can be skipped, since the phy should interrupt when the link returns. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-17phy: marvell: Add support for 88E1540 PHYAndrew Lunn1-0/+16
The 88E1540 can be found embedded in the Marvell 88E6352 switch. It is compatible with the 88E1510, so add support for it, using the 88E1510 specific functions. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-16net: phy: vitesse: add support for VSC8601Måns Rullgård1-1/+15
This adds support for the Vitesse VSC8601 PHY. Generic functions are used for everything except interrupt handling. Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-16net: phy: at803x: support interrupt on 8030 and 8035Måns Rullgård1-0/+4
Commit 77a993942 "phy/at8031: enable at8031 to work on interrupt mode" added interrupt support for the 8031 PHY but left out the other two chips supported by this driver. This patch sets the .ack_interrupt and .config_intr functions for the 8030 and 8035 drivers as well. Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-06Merge tag 'spi-v4.4' of ↵Linus Torvalds1-1/+0
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi Pull spi updates from Mark Brown: "Quite a lot of activity in SPI this cycle, almost all of it in drivers with a few minor improvements and tweaks in the core. - Updates to pxa2xx to support Intel Broxton and multiple chip selects. - Support for big endian in the bcm63xx driver. - Multiple slave support for the mt8173 - New driver for the auxiliary SPI controller in bcm2835 SoCs. - Support for Layerscale SoCs in the Freescale DSPI driver" * tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits) spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI spi: pxa2xx: Add support for Intel Broxton spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals spi: pxa2xx: Add output control for multiple Intel LPSS chip selects spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific spi: Add DSPI support for layerscape family spi: ti-qspi: improve ->remove() callback spi/spi-xilinx: Fix race condition on last word read spi: Drop owner assignment from spi_drivers spi: Add THIS_MODULE to spi_driver in SPI core spi: Setup the master controller driver before setting the chipselect spi: dw: replace magic constant by DW_SPI_DR spi: mediatek: mt8173 spi multiple devices support spi: mediatek: handle controller_data in mtk_spi_setup spi: mediatek: remove mtk_spi_config spi: mediatek: Update document devicetree bindings to support multiple devices spi: fix kernel-doc warnings about missing return desc in spi.c spi: fix kernel-doc warnings about missing return desc in spi.h spi: pxa2xx: Align a few defines spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select ...
2015-11-04Merge remote-tracking branches 'spi/topic/omap-100k', ↵Mark Brown1-1/+0
'spi/topic/omap-uwire', 'spi/topic/owner', 'spi/topic/pxa' and 'spi/topic/pxa2xx' into spi-next
2015-11-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-25/+49
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were fixing the "BH-ness" of the counter bumps whilst in 'net-next' the functions were modified to take an explicit 'net' parameter. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-03dp83640: Only wait for timestamps for packets with timestamping enabled.Stefan Sørensen1-12/+13
In the packet timestamping function, check that the ptp version and protocol of the packet matches what we have configured the hardware to actually generate timestamps for, before looking/waiting for a timestamp. Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-03dp83640: Prune rx timestamp list before reading from itStefan Sørensen1-0/+1
The list of rx timestamps are currently only pruned of old entries when a new entry is inserted. If no new entries are added, old timestamps may survive beyond their lifetime, possible causing them to be attached to packets with the same sequence number after a rollover. Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-03dp83640: Delay scheduled work.Stefan Sørensen1-8/+12
Currently rx_timestamp_work reschedules itself as a regular workqueue item, effectively causing it run constantly as long as there are packets left in the queue. Fix by using delayed workqueue items, limiting it to run only every two jiffies. Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-03dp83640: Include hash in timestamp/packet matchingStefan Sørensen1-3/+15
Only using the message type and sequence id for matching timestamps with packets is error prone, as multiple clients may very well be sending packets with the same messagetype and timestamp at the same time. Fix by extending the check to include the hash of bytes 20-29 (source id in PTPv2) that is provided with the timestamps. Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-03net: phy: fix a bug in get_phy_c45_idsShaohui Xie1-25/+49
When probing devices-in-package for a c45 phy, device zero is the last device to probe, however, if driver reads 0 from device zero, c45_ids->devices_in_package is set to '0', the loop condition of probing will be matched again, see codes below: for (i = 1;i < num_ids && c45_ids->devices_in_package == 0;i++) driver will run in a dead loop. This patch restructures the bug and confusing loop, it provides a helper function get_phy_c45_devs_in_pkg which to read devices-in-package registers of a MMD, and rewrites the loop with using the helper function. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-01Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2-0/+3
2015-10-28spi: Drop owner assignment from spi_driversAndrew F. Davis1-1/+0
An spi_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Andrew F. Davis <afd@ti.com> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-11-16 02:32:20 +0300