| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
mlx5e_close_xdpsq does the cleanup: it calls mlx5e_free_xdpsq_descs to
free the outstanding descriptors, which relies on
mlx5e_page_release_dynamic and page_pool_release_page. However,
page_pool_destroy is already called by this point, because
mlx5e_close_rq runs before mlx5e_close_xdpsq.
This commit fixes the use-after-free by swapping mlx5e_close_xdpsq and
mlx5e_close_rq.
The commit cited below started calling page_pool_destroy directly from
the driver. Previously, the page pool was destroyed under a call_rcu
from xdp_rxq_info_unreg_mem_model, which would defer the deallocation
until after the XDPSQ is cleaned up.
Fixes: 1da4bbeffe41 ("net: core: page_pool: add user refcnt and reintroduce page_pool_destroy")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Ageing time is not converted from clock_t to jiffies which results
incorrect ageing timeout calculation in workqueue update task. Fix it by
applying clock_t_to_jiffies() to provided value.
Fixes: c636a0f0f3f0 ("net/mlx5: Bridge, dynamic entry ageing")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
It could be local and remote are on the same machine and the route
result will be a local route which will result in creating encap id
with src/dst mac address of 0.
Fixes: a54e20b4fcae ("net/mlx5e: Add basic TC tunnel set action for SRIOV offloads")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
While processing encapsulated packet on RX, one of the fields that is
checked is the inner packet length. If the length as specified in the header
doesn't match the actual inner packet length, the packet is invalid
and should be dropped. However, such packet caused the NIC to hang.
This patch turns on a 'fail_on_error' HW bit which allows HW to drop
such an invalid packet while processing RX packet and trying to decap it.
Fixes: ad17dc8cf910 ("net/mlx5: DR, Move STEv0 action apply logic")
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Clean SF resources if mlx5 eth failed to initialize.
Fixes: 1958fc2f0712 ("net/mlx5: SF, Add auxiliary device driver")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This patch adds skb's frag page recycling support based on
the frag page support in page pool.
The performance improves above 10~20% for single thread iperf
TCP flow with IOMMU disabled when iperf server and irq/NAPI
have a different CPU.
The performance improves about 135%(14Gbit to 33Gbit) for single
thread iperf TCP flow when IOMMU is in strict mode and iperf
server shares the same cpu with irq/NAPI.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, page->pp is cleared and set everytime the page
is recycled, which is unnecessary.
So only set the page->pp when the page is added to the page
pool and only clear it when the page is released from the
page pool.
This is also a preparation to support allocating frag page
in page pool.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
iavf driver should set RSS LUT and key unconditionally in reset
path. Currently, the driver does not do that. This patch fixes
this issue.
Fixes: 2c86ac3c7079 ("i40evf: create a generic config RSS function")
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In some circumstances, such as with bridging, it's possible that the
stack will add the device's own MAC address to its unicast address list.
If, later, the stack deletes this address, the driver will receive a
request to remove this address.
The driver stores its current MAC address as part of the VSI MAC filter
list instead of separately. So, this causes a problem when the device's
MAC address is deleted unexpectedly, which results in traffic failure in
some cases.
The following configuration steps will reproduce the previously
mentioned problem:
> ip link set eth0 up
> ip link add dev br0 type bridge
> ip link set br0 up
> ip addr flush dev eth0
> ip link set eth0 master br0
> echo 1 > /sys/class/net/br0/bridge/vlan_filtering
> modprobe -r veth
> modprobe -r bridge
> ip addr add 192.168.1.100/24 dev eth0
The following ping command fails due to the netdev->dev_addr being
deleted when removing the bridge module.
> ping <link partner>
Fix this by making sure to not delete the netdev->dev_addr during MAC
address sync. After fixing this issue it was noticed that the
netdev_warn() in .set_mac was overly verbose, so make it at
netdev_dbg().
Also, there is a possibility of a race condition between .set_mac and
.set_rx_mode. Fix this by calling netif_addr_lock_bh() and
netif_addr_unlock_bh() on the device's netdev when the netdev->dev_addr
is going to be updated in .set_mac.
Fixes: e94d44786693 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Liang Li <liali@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When VFs are setup and torn down in quick succession, it is possible
that a VF is torn down by the PF while the VF's virtchnl requests are
still in the PF's mailbox ring. Processing the VF's virtchnl request
when the VF itself doesn't exist results in undefined behavior. Fix
this by adding a check to stop processing virtchnl requests when VF
teardown is in progress.
Fixes: ddf30f7ff840 ("ice: Add handler to configure SR-IOV")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The userspace utility "driverctl" can be used to change/override the
system's default driver choices. This is useful in some situations
(buggy driver, old driver missing a device ID, trying a workaround,
etc.) where the user needs to load a different driver.
However, this is also prone to user error, where a driver is mapped
to a device it's not designed to drive. For example, if the ice driver
is mapped to driver iavf devices, the ice driver crashes.
Add a check to return an error if the ice driver is being used to
probe a virtual function.
Fixes: 837f08fdecbe ("ice: Add basic driver framework for Intel(R) E800 Series")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
reproduce:
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
make.cross ARCH=m68k m5272c3_defconfig
make.cross ARCH=m68k
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_eee_mode_set':
>> drivers/net/ethernet/freescale/fec_main.c:2758:33: error: 'FEC_LPI_SLEEP' undeclared (first use in this function); did you mean 'FEC_ECR_SLEEP'?
2758 | writel(sleep_cycle, fep->hwp + FEC_LPI_SLEEP);
| ^~~~~~~~~~~~~
arch/m68k/include/asm/io_no.h:25:66: note: in definition of macro '__raw_writel'
25 | #define __raw_writel(b, addr) (void)((*(__force volatile u32 *) (addr)) = (b))
| ^~~~
drivers/net/ethernet/freescale/fec_main.c:2758:2: note: in expansion of macro 'writel'
2758 | writel(sleep_cycle, fep->hwp + FEC_LPI_SLEEP);
| ^~~~~~
drivers/net/ethernet/freescale/fec_main.c:2758:33: note: each undeclared identifier is reported only once for each function it appears in
2758 | writel(sleep_cycle, fep->hwp + FEC_LPI_SLEEP);
| ^~~~~~~~~~~~~
arch/m68k/include/asm/io_no.h:25:66: note: in definition of macro '__raw_writel'
25 | #define __raw_writel(b, addr) (void)((*(__force volatile u32 *) (addr)) = (b))
| ^~~~
drivers/net/ethernet/freescale/fec_main.c:2758:2: note: in expansion of macro 'writel'
2758 | writel(sleep_cycle, fep->hwp + FEC_LPI_SLEEP);
| ^~~~~~
>> drivers/net/ethernet/freescale/fec_main.c:2759:32: error: 'FEC_LPI_WAKE' undeclared (first use in this function)
2759 | writel(wake_cycle, fep->hwp + FEC_LPI_WAKE);
| ^~~~~~~~~~~~
arch/m68k/include/asm/io_no.h:25:66: note: in definition of macro '__raw_writel'
25 | #define __raw_writel(b, addr) (void)((*(__force volatile u32 *) (addr)) = (b))
| ^~~~
drivers/net/ethernet/freescale/fec_main.c:2759:2: note: in expansion of macro 'writel'
2759 | writel(wake_cycle, fep->hwp + FEC_LPI_WAKE);
| ^~~~~~
This patch adds register definition for M5272 platform to pass build.
Fixes: b82f8c3f1409 ("net: fec: add eee mode tx lpi support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All kernel devlink implementations call to devlink_alloc() during
initialization routine for specific device which is used later as
a parent device for devlink_register().
Such late device assignment causes to the situation which requires us to
call to device_register() before setting other parameters, but that call
opens devlink to the world and makes accessible for the netlink users.
Any attempt to move devlink_register() to be the last call generates the
following error due to access to the devlink->dev pointer.
[ 8.758862] devlink_nl_param_fill+0x2e8/0xe50
[ 8.760305] devlink_param_notify+0x6d/0x180
[ 8.760435] __devlink_params_register+0x2f1/0x670
[ 8.760558] devlink_params_register+0x1e/0x20
The simple change of API to set devlink device in the devlink_alloc()
instead of devlink_register() fixes all this above and ensures that
prior to call to devlink_register() everything already set.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CPSW switchdev driver inherited fix from commit 9421c9015047 ("net:
ethernet: ti: cpsw: fix min eth packet size") which changes min TX packet
size to 64bytes (VLAN_ETH_ZLEN, excluding ETH_FCS). It was done to fix HW
packed drop issue when packets are sent from Host to the port with PVID and
un-tagging enabled. Unfortunately this breaks some other non-switch
specific use-cases, like:
- [1] CPSW port as DSA CPU port with DSA-tag applied at the end of the
packet
- [2] Some industrial protocols, which expects min TX packet size 60Bytes
(excluding FCS).
Fix it by configuring min TX packet size depending on driver mode
- 60Bytes (ETH_ZLEN) for multi mac (dual-mac) mode
- 64Bytes (VLAN_ETH_ZLEN) for switch mode
and update it during driver mode change and annotate with
READ_ONCE()/WRITE_ONCE() as it can be read by napi while writing.
[1] https://lore.kernel.org/netdev/20210531124051.GA15218@cephalopod/
[2] https://e2e.ti.com/support/arm/sitara_arm/f/791/t/701669
Cc: stable@vger.kernel.org
Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Reported-by: Ben Hutchings <ben.hutchings@essensium.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need the driver core fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some older Broadcom debug tools use window 5 and may conflict, so switch
to use window 6 instead.
Fixes: 118612d519d8 ("bnxt_en: Add PTP clock APIs, ioctls, and ethtool methods")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New firmware interface requires the PTP sequence ID header offset to
be passed to the firmware to properly find the matching timestamp
for all protocols.
Fixes: 83bb623c968e ("bnxt_en: Transmit and retrieve packet timestamps")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The key change is the firmware call to retrieve the PTP TX timestamp.
The header offset for the PTP sequence number field is now added.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Devlink port already has pointer to the devlink instance and all API
calls that forward these devlink ports to the drivers perform same
"devlink_port->devlink" assignment before actual call.
This patch removes useless parameter and allows us in the future
to create specific devlink_port_ops to manage user space access with
reliable ops assignment.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When compiling with clang in certain configurations, an objtool warning
appears:
drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.o: warning: objtool:
ipq806x_gmac_probe() falls through to next function phy_modes()
This happens because the unreachable annotation in the third switch
statement is not eliminated. The compiler should know that the first
default case would prevent the second and third from being reached as
the comment notes but sanitizer options can make it harder for the
compiler to reason this out.
Help the compiler out by eliminating the unreachable() annotation and
unifying the default case error handling so that there is no objtool
warning, the meaning of the code stays the same, and there is less
duplication.
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The true check on the variable startable in the ternary operator
is always false because the previous if statement handles the true
condition for startable. Hence the ternary check is dead code and
can be removed.
Addresses-Coverity: ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original L0 and L1 entrance latencies of RTL8106e are 4us. And
they cause the delay of link-up interrupt when enabling ASPM. Change
the L0 entrance latency to 7us and L1 entrance latency to 32us. Then,
they could avoid the issue.
Tested-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 1ee8856de82faec9bc8bd0f2308a7f27e30ba207.
This is used to re-enable ASPM on RTL8106e, if it is possible.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 9ffc513f95ee ("net: ethernet: ti: davinci_cpdma: drop
frame padding") which has depndency from not yet merged patch [1] and so
breaks cpsw_new driver.
[1] https://patchwork.kernel.org/project/netdevbpf/patch/20210805145511.12016-1-grygorii.strashko@ti.com/
Fixes: 9ffc513f95ee ("net: ethernet: ti: davinci_cpdma: drop frame padding")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20210806142809.15069-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On s390, the following build warning occurs:
drivers/net/ethernet/marvell/mvpp2/mvpp2.h:844:2: warning: overflow in
conversion from 'long unsigned int' to 'int' changes value from
'18446744073709551584' to '-32' [-Woverflow]
844 | ((total_size) - MVPP2_SKB_HEADROOM - MVPP2_SKB_SHINFO_SIZE)
This happens because MVPP2_SKB_SHINFO_SIZE, which is 320 bytes (which is
already 64-byte aligned) on some architectures, actually gets ALIGN'd up
to 512 bytes in the s390 case.
So then, when this is invoked:
MVPP2_RX_MAX_PKT_SIZE(MVPP2_BM_SHORT_FRAME_SIZE)
...that turns into:
704 - 224 - 512 == -32
...which is not a good frame size to end up with! The warning above is a
bit lucky: it notices a signed/unsigned bad behavior here, which leads
to the real problem of a frame that is too short for its contents.
Increase MVPP2_BM_SHORT_FRAME_SIZE by 32 (from 704 to 736), which is
just exactly big enough. (The other values can't readily be changed
without causing a lot of other problems.)
Fixes: 07dd0a7aae7f ("mvpp2: add basic XDP support")
Cc: Sven Auhagen <sven.auhagen@voleatech.de>
Cc: Matteo Croce <mcroce@microsoft.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables support for hard irqs deferral feature from Eric Dumazet
[1] for TI K3 CPSW driver by using napi_complete_done() in TX completion
path.
Depending on gro_flush_timeout and napi_defer_hard_irqs at gives up to 30%
CPU utilization reduction:
gro_flush_timeout=50000
napi_defer_hard_irqs=2
netperf -l 10 -H 192.168.1.1 -t UDP_STREAM -c -C -- -m 1470
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.1 () port 0 AF_INET
Socket Message Elapsed Messages CPU Service
Size Size Time Okay Errors Throughput Util Demand
bytes bytes secs # # 10^6bits/sec % SS us/KB
before:
212992 1470 10.00 809632 0 952.0 42.98 14.792
212992 10.00 809630 952.0 50.66 8.719
after:
212992 1470 10.00 813686 0 956.8 32.14 11.009
212992 10.00 813686 956.8 50.05 8.570
[1] https://lore.kernel.org/netdev/20200422161329.56026-1-edumazet@google.com/
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On TI K3 am64x platform the issue with RX IRQ is observed - it's become
disabled forever after .ndo_stop(). The K3 CPSW driver manipulates RX IRQ
by using standard Linux enable_irq()/disable_irq_nosync() API as there is
no IRQ enable/disable options in CPSW HW itself, as result during
.ndo_stop() following sequence happens
phy_stop()
teardown TX/RX channels
wait for TX tdown complete
napi_disable(TX)
clean up TX channels
(a)
napi_disable(RX)
At point (a) it's not possible to predict if RX IRQ was triggered or not.
if RX IRQ was triggered then it also not possible to definitely say if RX
NAPI was run or only scheduled and immediately canceled by
napi_disable(RX). Actually the last case causes RX IRQ to be permanently
disabled.
Another observed issue is that RX IRQ enable counter become unbalanced if
(gro_flush_timeout =! 0) while (napi_defer_hard_irqs == 0):
Unbalanced enable for IRQ 44
WARNING: CPU: 0 PID: 10 at ../kernel/irq/manage.c:776 __enable_irq+0x38/0x80
__enable_irq+0x38/0x80
enable_irq+0x54/0xb0
am65_cpsw_nuss_rx_poll+0x2f4/0x368
__napi_poll+0x34/0x1b8
net_rx_action+0xe4/0x220
_stext+0x11c/0x284
run_ksoftirqd+0x4c/0x60
To avoid above issues introduce flag indicating if RX was actually disabled
before enabling it in am65_cpsw_nuss_rx_poll() and restore RX IRQ state in
.ndo_open()
Fixes: 4f7cce272403 ("net: ethernet: ti: am65-cpsw: add support for am64x cpsw3g")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hence all users of davinci_cpdma switched to skb_put_padto() the frame
padding can be removed from it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use skb_put_padto() instead of skb_padto() so skb->len also got updated, as
preparation for further removing frame padding from cpdma.
It also makes xmit path more clear and linear.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use skb_put_padto() instead of skb_padto() so skb->len also got updated, as
preparation for further removing frame padding from cpdma.
It also makes xmit path more clear and linear.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df9322 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098ed ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df9322 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If both eswitches are in switchdev mode and the uplink representors
are enslaved to the same bond device create a shared FDB configuration.
When moving to shared FDB mode not only the hardware needs be configured
but the RDMA driver needs to reconfigure itself.
When such change is done, unload the RDMA devices, configure the hardware
and load the RDMA representors.
When destroying the lag (can happen if a PCI function is unbinded,
driver is unloaded or by just removing a netdev from the bond) make sure
to restore the system to the previous state only if possible.
For example, if a PCI function is unbinded there is no need to load the
representors as the device is going away.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Shared FDB allows to direct traffic from all the vports in the HCA to a
single eswitch. In order to do that three things are needed.
1) Point the ingress ACL of the slave uplink to that of the master.
With this, wire traffic from both uplinks will reach the same eswitch
with the same metadata where a single steering rule can catch traffic
from both ports.
2) Set the FDB root flow table of the slave's eswitch to that of the
master. As this flow table can change dynamically make sure to
sync it on any set root flow table FDB command.
This will make sure traffic from SFs, VFs, ECPFs and PFs reach the
master eswitch.
3) Split wire traffic at the eswitch manager egress ACL so that it's
directed to the native eswitch manager. We only treat wire traffic
from both ports the same at the eswitch level. If such traffic wasn't
handled in the eswitch it needs to reach the right representor to be
processed by software. For example LACP packets should *always*
reach the right uplink representor for correct operation.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
If a netdev is removed from the lag the lag should be destroyed.
With downstream patches this might trigger a reconfiguration of
representors on a different eswitch and such we don't have the proper
locking to so from this path. Move the destruction to be done by the
workqueue.
As the destruction won't affect the netdev side it okay to do so.
The RDMA side will be reconfigured and it already coded to handle such
reconfiguration.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently when doing hardware lag we check the eswitch mode
but as this isn't done under a lock the check isn't valid.
As the code needs to sync between two different devices an extra
care is needed.
- When going to change eswitch mode, if hardware lag is active destroy it.
- While changing eswitch modes block any hardware bond creation.
- Delay handling bonding events until there are no mode changes in
progress.
- When attaching a new mdev to lag, block until there is no mode change
in progress. In order for the mode change to finish the interface lock
will have to be taken. Release the lock and sleep for 100ms to
allow forward progress. As this is a very rare condition (can happen if
the user unbinds and binds a PCI function while also changing eswitch
mode of the other PCI function) it has no real world impact.
As taking multiple eswitch mode locks is now required lockdep will
complain about a possible deadlock. Register a key per eswitch to make
lockdep happy.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When two mlx5 devices are paired in switchdev mode, always offload the
send-to-vport rule to the peer E-Switch. This allows to abstract
the logic when this is really necessary (single FDB) and combine
the logic of both cases into one.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This callback will allow to notify representors about relevant events
when in OFFLOADS mode. In downstream patches, this will be used to notify
about PAIR/UNPAIR devcom events.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
FTEs are added with mapped metadata which is saved per eswitch.
When uplink reps are bonded and we are in a single FDB mode,
we could fail to find metadata which was stored on one eswitch mapping
but not the other or with a different id.
To resolve this issue use shared mapping between eswitch ports.
We do not have any conflict using a single mapping, for a type,
between the ports.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The shared mapping is identified by an id and type.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Set the flow source param to local vport for the uplink rep
send-to-vport rule.
This will comply with the recent changes in SW steering that
use the flow source as an indication for the rule type - rx or tx.
Since the uplink send-to-vport rule is forwarding traffic to the wire
it has to indicate that it is an sx rule and can't use the any port
value in the flow source.
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In shared FDB there is only one eswitch which is active and it receives
traffic from all representors and all vports in the HCA.
While the Ethernet representor will always reside on its native PF
the IB representor will not. Extend send to vport rule creation to
support such flows. Need to account for source vport that sends the
traffic (on which the representors resides) and the target eswitch
the traffic which reach.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
As shared FDB requires changes in two subsystems first expose the needed
core functions so the RDMA side can be changed.
mlx5_lag_is_master(): return true if a given mlx5 device is the lag master.
mlx5_lag_is_shared_fdb(): Returns true if the lag mode is shared FDB.
mlx5_lag_get_peer_mdev(): Return the peer mdev in lag.
The mentioned functions will be used by downstream patches in order
to add support for shared FDB for the RDMA side.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Export a function so users can retrieve the mellanox device that manages
the eswitch from the eswitch device.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Smatch says:
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
Since vdev pointer is netdev private data accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Fixes: 6cca200362b4 ("vxge: cleanup probe error paths")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Smatch says:
drivers/net/ethernet/freescale/fec_main.c:3994 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
drivers/net/ethernet/freescale/fec_main.c:3995 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
Since fep pointer is netdev private data, accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: a31eda65ba21 ("net: fec: fix clock count mis-match")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
am65_cpsw_port_offload_fwd_mark_update()
The am65_cpsw_port_offload_fwd_mark_update() causes NULL exception crash
when there is at least one disabled port and any other port added to the
bridge first time.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000858
pc : am65_cpsw_port_offload_fwd_mark_update+0x54/0x68
lr : am65_cpsw_netdevice_event+0x8c/0xf0
Call trace:
am65_cpsw_port_offload_fwd_mark_update+0x54/0x68
notifier_call_chain+0x54/0x98
raw_notifier_call_chain+0x14/0x20
call_netdevice_notifiers_info+0x34/0x78
__netdev_upper_dev_link+0x1c8/0x290
netdev_master_upper_dev_link+0x1c/0x28
br_add_if+0x3f0/0x6d0 [bridge]
Fix it by adding proper check for port->ndev != NULL.
Fixes: 2934db9bcb30 ("net: ti: am65-cpsw-nuss: Add netdevice notifiers")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the error code if bnx2x_alloc_fw_stats_mem() fails. The current
code returns success.
Fixes: ad5afc89365e ("bnx2x: Separate VF and PF logic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit b0e81817629a496854ff1799f6cbd89597db65fd. Explicit
driver dependency on the bridge is no longer needed since
switchdev_bridge_port_{,un}offload() is no longer implemented by the
bridge driver but by switchdev.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the introduction of explicit offloading API in switchdev in commit
2f5dc00f7a3e ("net: bridge: switchdev: let drivers inform which bridge
ports are offloaded"), we started having Ethernet switch drivers calling
directly into a function exported by net/bridge/br_switchdev.c, which is
a function exported by the bridge driver.
This means that drivers that did not have an explicit dependency on the
bridge before, like cpsw and am65-cpsw, now do - otherwise it is not
possible to call a symbol exported by a driver that can be built as
module unless you are a module too.
There was an attempt to solve the dependency issue in the form of commit
b0e81817629a ("net: build all switchdev drivers as modules when the
bridge is a module"). Grygorii Strashko, however, says about it:
| In my opinion, the problem is a bit bigger here than just fixing the
| build :(
|
| In case, of ^cpsw the switchdev mode is kinda optional and in many
| cases (especially for testing purposes, NFS) the multi-mac mode is
| still preferable mode.
|
| There were no such tight dependency between switchdev drivers and
| bridge core before and switchdev serviced as independent, notification
| based layer between them, so ^cpsw still can be "Y" and bridge can be
| "M". Now for mostly every kernel build configuration the CONFIG_BRIDGE
| will need to be set as "Y", or we will have to update drivers to
| support build with BRIDGE=n and maintain separate builds for
| networking vs non-networking testing. But is this enough? Wouldn't
| it cause 'chain reaction' required to add more and more "Y" options
| (like CONFIG_VLAN_8021Q)?
|
| PS. Just to be sure we on the same page - ARM builds will be forced
| (with this patch) to have CONFIG_TI_CPSW_SWITCHDEV=m and so all our
| automation testing will just fail with omap2plus_defconfig.
In the light of this, it would be desirable for some configurations to
avoid dependencies between switchdev drivers and the bridge, and have
the switchdev mode as completely optional within the driver.
Arnd Bergmann also tried to write a patch which better expressed the
build time dependency for Ethernet switch drivers where the switchdev
support is optional, like cpsw/am65-cpsw, and this made the drivers
follow the bridge (compile as module if the bridge is a module) only if
the optional switchdev support in the driver was enabled in the first
place:
https://patchwork.kernel.org/project/netdevbpf/patch/20210802144813.1152762-1-arnd@kernel.org/
but this still did not solve the fact that cpsw and am65-cpsw now must
be built as modules when the bridge is a module - it just expressed
correctly that optional dependency. But the new behavior is an apparent
regression from Grygorii's perspective.
So to support the use case where the Ethernet driver is built-in,
NET_SWITCHDEV (a bool option) is enabled, and the bridge is a module, we
need a framework that can handle the possible absence of the bridge from
the running system, i.e. runtime bloatware as opposed to build-time
bloatware.
Luckily we already have this framework, since switchdev has been using
it extensively. Events from the bridge side are transmitted to the
driver side using notifier chains - this was originally done so that
unrelated drivers could snoop for events emitted by the bridge towards
ports that are implemented by other drivers (think of a switch driver
with LAG offload that listens for switchdev events on a bonding/team
interface that it offloads).
There are also events which are transmitted from the driver side to the
bridge side, which again are modeled using notifiers.
SWITCHDEV_FDB_ADD_TO_BRIDGE is an example of this, and deals with
notifying the bridge that a MAC address has been dynamically learned.
So there is a precedent we can use for modeling the new framework.
The difference compared to SWITCHDEV_FDB_ADD_TO_BRIDGE is that the work
that the bridge needs to do when a port becomes offloaded is blocking in
its nature: replay VLANs, MDBs etc. The calling context is indeed
blocking (we are under rtnl_mutex), but the existing switchdev
notification chain that the bridge is subscribed to is only the atomic
one. So we need to subscribe the bridge to the blocking switchdev
notification chain too.
This patch:
- keeps the driver-side perception of the switchdev_bridge_port_{,un}offload
unchanged
- moves the implementation of switchdev_bridge_port_{,un}offload from
the bridge module into the switchdev module.
- makes everybody that is subscribed to the switchdev blocking notifier
chain "hear" offload & unoffload events
- makes the bridge driver subscribe and handle those events
- moves the bridge driver's handling of those events into 2 new
functions called br_switchdev_port_{,un}offload. These functions
contain in fact the core of the logic that was previously in
switchdev_bridge_port_{,un}offload, just that now we go through an
extra indirection layer to reach them.
Unlike all the other switchdev notification structures, the structure
used to carry the bridge port information, struct
switchdev_notifier_brport_info, does not contain a "bool handled".
This is because in the current usage pattern, we always know that a
switchdev bridge port offloading event will be handled by the bridge,
because the switchdev_bridge_port_offload() call was initiated by a
NETDEV_CHANGEUPPER event in the first place, where info->upper_dev is a
bridge. So if the bridge wasn't loaded, then the CHANGEUPPER event
couldn't have happened.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid reconfig problems due to failures in netif_set_real_num_tx_queues()
by using netif_set_real_num_queues().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
