| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The mlxsw driver relies on NETDEV_CHANGEUPPER events to configure the
device in case a port is enslaved to a master netdev such as bridge or
bond.
Since the driver ignores events unrelated to its ports and their
uppers, it's possible to engineer situations in which the device's data
path differs from the kernel's.
One example to such a situation is when a port is enslaved to a bond
that is already enslaved to a bridge. When the bond was enslaved the
driver ignored the event - as the bond wasn't one of its uppers - and
therefore a bridge port instance isn't created in the device.
Until such configurations are supported forbid them by checking that the
upper device doesn't have uppers of its own.
Fixes: 0d65fc13042f ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Nogah Frankel <nogahf@mellanox.com>
Tested-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cq_period_mode assignment was mistakenly removed so it was always set to "0",
which is EQE based moderation, regardless of the device CAPs and
requested value in ethtool.
Fixes: 6a9764efb255 ("net/mlx5e: Isolate open_channels from priv->params")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix inline header size, make sure it is not greater than skb len.
This bug effects small packets, for example L2 packets with size < 18.
Fixes: ae76715d153e ("net/mlx5e: Check the minimum inline header mode before xmit")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When changing from switchdev to legacy mode, all the representor port
devices (uplink nic and reps) are cleaned up. Part of this cleaning
process is removing the neigh entries and the hash table containing them.
However, a representor neigh entry might be linked to the uplink port
hash table and if the uplink nic is cleaned first the cleaning of the
representor will end up in null deref.
Fix that by unloading the representors in the opposite order of load.
Fixes: cb67b832921c ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently if vxlan tunnel ipv6 src isn't supplied the driver fails to
resolve it as part of the route lookup. The resulting encap header
is left with a zeroed out ipv6 src address so the packets are sent
with this src ip.
Use an appropriate route lookup API that also resolves the source
ipv6 address if it's not supplied.
Fixes: ce99f6b97fcd ('net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, increasing the number of combined channels is changing
the RSS spread to use the new created channels.
Prevent the RSS spread change in case the user explicitly declare it,
to avoid overriding user configuration.
Tested:
when RSS default:
# ethtool -L ens8 combined 4
RSS spread will change and point to 4 channels.
# ethtool -X ens8 equal 4
# ethtool -L ens8 combined 6
RSS will not change after increasing the number of the channels.
Fixes: 8bf368620486 ('ethtool: ensure channel counts are within bounds during SCHANNELS')
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Function mlx5e_dealloc_rx_wqe is using page pointer value as an
indication to valid DMA mapping. In case that the mapping failed, we
released the page but kept the dangling pointer. Store the page pointer
only after the DMA mapping passed to avoid invalid page DMA unmap.
Fixes: bc77b240b3c5 ("net/mlx5e: Add fragmented memory support for RX multi packet WQE")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
MLX5_INTERFACE_STATE_SHUTDOWN is not used in the code.
Fixes: 5fc7197d3a25 ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
There is an issue where the firmware fails during mlx5_load_one,
the health_care timer detects the issue and schedules a health_care call.
Then the mlx5_load_one detects the issue, cleans up and quits. Then
the health_care starts and calls mlx5_unload_one to clean up the resources
that no longer exist and causes kernel panic.
The root cause is that the bit MLX5_INTERFACE_STATE_DOWN is not set
after mlx5_load_one fails. The solution is removing the bit
MLX5_INTERFACE_STATE_DOWN and quit mlx5_unload_one if the
bit MLX5_INTERFACE_STATE_UP is not set. The bit MLX5_INTERFACE_STATE_DOWN
is redundant and we can use MLX5_INTERFACE_STATE_UP instead.
Fixes: 5fc7197d3a25 ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Support for ISSI version 0 was recently broken as the arm_srq_cmd
command, which is used only for ISSI version 0, was given the opcode
for ISSI version 1 instead of ISSI version 0.
Change arm_srq_cmd to use the correct command opcode for ISSI version
0.
Fixes: af1ba291c5e4 ('{net, IB}/mlx5: Refactor internal SRQ API')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Current code doesn't report DCB_CAP_DCBX_HOST capability when query
through getcap. User space lldptool expects capability to have HOST mode
set when it wants to configure DCBX CEE mode. In absence of HOST mode
capability, lldptool fails to switch to CEE mode.
This fix returns DCB_CAP_DCBX_HOST capability when port's DCBX
controlled mode is under software control.
Fixes: 3a6a931dfb8e ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
qos capability is the master capability bit that determines
if the DCBX is supported for the PCI function. If this bit is off,
driver cannot run any dcbx code.
Fixes: e207b7e99176 ("net/mlx5e: ConnectX-4 firmware support for DCBX")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Update the value of the mrouter flag in struct mlxsw_sp_bridge_port when
it is being changed.
Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
enable_4k_uar module parameter was added in patch cited below to
address the backward compatibility issue in SRIOV when the VM has
system's PAGE_SIZE uar implementation and the Hypervisor has 4k uar
implementation.
The above compatibility issue does not exist in the non SRIOV case.
In this patch, we always enable 4k uar implementation if SRIOV
is not enabled on mlx4's supported cards.
Fixes: 76e39ccf9c36 ("net/mlx4_core: Fix backward compatibility on VFs")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
if the NIC fails to validate the checksum on TCP/UDP, and validation of IP
checksum is successful, the driver subtracts the pseudo-header checksum
from the value obtained by the hardware and sets CHECKSUM_COMPLETE. Don't
do that if protocol is IPPROTO_SCTP, otherwise CRC32c validation fails.
V2: don't test MLX4_CQE_STATUS_IPV6 if MLX4_CQE_STATUS_IPV4 is set
Reported-by: Shuang Li <shuali@redhat.com>
Fixes: f8c6455bb04b ("net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each multicast group (MID) stores a bitmap of ports to which a packet
should be forwarded to in case an MDB entry associated with the MID is
hit.
Since the initial introduction of IGMP snooping in commit 3a49b4fde2a1
("mlxsw: Adding layer 2 multicast support") the driver didn't correctly
free these multicast groups upon ungraceful situations such as the
removal of the upper bridge device or module removal.
The correct way to fix this is to associate each MID with the bridge
ports member in it and then drop the reference in case the bridge port
is destroyed, but this will result in a lot more code and will be fixed
in net-next.
For now, upon module removal, traverse the MID list and release each
one.
Fixes: 3a49b4fde2a1 ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some operations in the bridge driver such as MDB deletion are preformed
in an atomic context and thus deferred to a process context by the
switchdev infrastructure.
Therefore, by the time the operation is performed by the underlying
device driver it's possible the bridge port context is already gone.
This is especially true for removal flows, but theoretically can also be
invoked during addition.
Remove the warnings in such situations and return normally.
Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Fixes: 3922285d96e7 ("net: bridge: Add support for offloading port attributes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:
QUERY_DEV_CAP_DIAG_RPRT_PER_PORT
However, it failed to introduce a corresponding entry in function
dump_dev_cap_flags2() for outputting a line in the message log
when this capability bit is set.
The change here fixes that omission.
Fixes: c7c122ed67e4 ("net/mlx4: Add diagnostic counters capability bit")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:
MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP
However the value of MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP needs to stay
consistent with the value used in another namespace in
function dump_dev_cap_flags2(), which is manually kept in sync.
The change here restores that consistency.
Fixes: 7c3d21c8153c ("net/mlx4_core: Preparation for VF vlan protocol 802.1ad")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The index value in function dump_dev_cap_flags2() for outputting
"sl to vl mapping table change event support" needs to be
consistent with the value of the enumerated constant
MLX4_DEV_CAP_FLAG2_SL_TO_VL_CHANGE_EVENT defined in file
include/linux/mlx4_device.h
The change here restores that consistency.
Fixes: fd10ed8e6f42 ("IB/mlx4: Fix possible vl/sl field mismatch in LRH header in QP1 packets")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when WoL is supported but disabled, ethtool reports:
"Supports Wake-on: d".
Fix the indication of Wol support, so that the indication
remains "g" all the time if the NIC supports WoL.
Tested:
As accepted, when NIC supports WoL- ethtool reports:
Supports Wake-on: g
Wake-on: d
when NIC doesn't support WoL- ethtool reports:
Supports Wake-on: d
Wake-on: d
Fixes: 14c07b1358ed ("mlx4: Wake on LAN support")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When adding ethtool steering rule with action DISCARD we wrongly
pass a NULL dest with dest_num 1 to mlx5_add_flow_rules().
What this error seems to have caused is sending VPORT 0
(MLX5_FLOW_DESTINATION_TYPE_VPORT) as the fte dest instead of no dests.
We have fte action correctly set to DROP so it might been ignored
anyways.
To reproduce use:
# sudo ethtool --config-nfc <dev> flow-type ether \
dst aa:bb:cc:dd:ee:ff action -1
Fixes: 74491de93712 ("net/mlx5: Add multi dest support")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This is done in order to ensure that work will not run after the cleanup.
Fixes: ef9814deafd0 ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The overflow_period is calculated in seconds. In order to use it
for delayed work scheduling translation to jiffies is needed.
Fixes: ef9814deafd0 ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add the missing option to enable the PTP_CLK_PPS function.
In this case pin should be configured as 1PPS IN first and
then it will be connected to PPS mechanism.
Events will be reported as PTP_CLOCK_PPSUSR events to relevant sysfs.
Fixes: ee7f12205abc ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to fix the drift in 1PPS out need to adjust the next pulse.
On each 1PPS out falling edge driver gets the event, then the event
handler adjusts the next pulse starting time.
Fixes: ee7f12205abc ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Need to disable the MTPPS and unsubscribe from the pulse events
when user disables the 1PPS functionality.
Fixes: ee7f12205abc ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to mark relevant fields while setting the MTPPS register
add field select. Otherwise it can cause a misconfiguration in
firmware.
Fixes: ee7f12205abc ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
outer_header_zero() routine checks if the outer_headers match of a
flow-table entry are all zero.
This function uses the size of whole fte_match_param, instead of just
the outer_headers member, causing failure to detect all-zeros if
any other members of the fte_match_param are non-zero.
Use the correct size for zero check.
Fixes: 6dc6071cfcde ("net/mlx5e: Add ethtool flow steering support")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
On interface remove, the clean-up was done incorrectly causing
an error in the log:
"SET_FLOW_TABLE_ROOT(0x92f) op_mod(0x0) failed...syndrome (0x7e9f14)"
This was caused by the following flow:
-ndo_uninit:
Move QP state to RST (this disconnects the QP from FT),
the QP cannot be attached to any FT unless it is in RTS.
-mlx5_rdma_netdev_free:
cleanup_rx: Destroy FT
cleanup_tx: Destroy QP and remove QPN from FT
This caused a problem when destroying current FT we tried to
re-attach the QP to the next FT which is not needed.
The correct flow is:
-mlx5_rdma_netdev_free:
cleanup_rx: remove QPN from FT & Destroy FT
cleanup_tx: Destroy QP
Fixes: 508541146af1 ("net/mlx5: Use underlay QPN from the root name space")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When driver fail to allocate an entry to send command to FW, it must
notify the calling function and release the memory allocated for
this command.
Fixes: e126ba97dba9e ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Completion on timeout should not free the driver command entry structure
as it will need to access it again once real completion event from FW
will occur.
Fixes: 73dd3a4839c1 ('net/mlx5: Avoid using pending command interface slots')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The tx_enabled lag event field is used to determine whether a slave is
active.
Current logic uses this value only if the mode is active-backup.
However, LACP mode, although considered a load balancing mode, can mark
a slave as inactive in certain situations (e.g., LACP timeout).
This fix takes the tx_enabled value into account when remapping, with
no respect to the LAG mode (this should not affect the behavior in XOR
mode, since in this mode both slaves are marked as active).
Fixes: 7907f23adc18 (net/mlx5: Implement RoCE LAG feature)
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Upon sriov enable, eswitch is always enabled.
Currently, if enable hca failed over all VFs, we would skip eswitch
disable as part of sriov disable, which will lead to resources leak.
Fix it by disabling eswitch if it was enabled (use indication from
eswitch mode).
Fixes: 6b6adee3dad2 ('net/mlx5: SRIOV core code refactoring')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Each FIB node holds a linked list of routes sharing the same prefix and
length. In the case of IPv4 it's ordered according to table ID, metric
and TOS and only the first route in the list is actually programmed to
the device.
In case a gatewayed route is added somewhere in the list, then after its
nexthop group will be refreshed and become valid (due to the resolution
of its gateway), it'll mistakenly overwrite the existing entry.
Example:
192.168.200.0/24 dev enp3s0np3 scope link metric 1000 offload
192.168.200.0/24 via 192.168.100.1 dev enp3s0np3 metric 1000 offload
Both routes are marked as offloaded despite the fact only the first one
should actually be present in the device's table.
When refreshing the nexthop group, don't write the route to the device's
table unless it's the first in its node.
Fixes: 9aecce1c7d97 ("mlxsw: spectrum_router: Correctly handle identical routes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) BPF verifier signed/unsigned value tracking fix, from Daniel
Borkmann, Edward Cree, and Josef Bacik.
2) Fix memory allocation length when setting up calls to
->ndo_set_mac_address, from Cong Wang.
3) Add a new cxgb4 device ID, from Ganesh Goudar.
4) Fix FIB refcount handling, we have to set it's initial value before
the configure callback (which can bump it). From David Ahern.
5) Fix double-free in qcom/emac driver, from Timur Tabi.
6) A bunch of gcc-7 string format overflow warning fixes from Arnd
Bergmann.
7) Fix link level headroom tests in ip_do_fragment(), from Vasily
Averin.
8) Fix chunk walking in SCTP when iterating over error and parameter
headers. From Alexander Potapenko.
9) TCP BBR congestion control fixes from Neal Cardwell.
10) Fix SKB fragment handling in bcmgenet driver, from Doug Berger.
11) BPF_CGROUP_RUN_PROG_SOCK_OPS needs to check for null __sk, from Cong
Wang.
12) xmit_recursion in ppp driver needs to be per-device not per-cpu,
from Gao Feng.
13) Cannot release skb->dst in UDP if IP options processing needs it.
From Paolo Abeni.
14) Some netdev ioctl ifr_name[] NULL termination fixes. From Alexander
Levin and myself.
15) Revert some rtnetlink notification changes that are causing
regressions, from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
net: bonding: Fix transmit load balancing in balance-alb mode
rds: Make sure updates to cp_send_gen can be observed
net: ethernet: ti: cpsw: Push the request_irq function to the end of probe
ipv4: initialize fib_trie prior to register_netdev_notifier call.
rtnetlink: allocate more memory for dev_set_mac_address()
net: dsa: b53: Add missing ARL entries for BCM53125
bpf: more tests for mixed signed and unsigned bounds checks
bpf: add test for mixed signed and unsigned bounds checks
bpf: fix up test cases with mixed signed/unsigned bounds
bpf: allow to specify log level and reduce it for test_verifier
bpf: fix mixed signed/unsigned derived min/max value bounds
ipv6: avoid overflow of offset in ip6_find_1stfragopt
net: tehuti: don't process data if it has not been copied from userspace
Revert "rtnetlink: Do not generate notifications for CHANGEADDR event"
net: dsa: mv88e6xxx: Enable CMODE config support for 6390X
dt-binding: ptp: Add SoC compatibility strings for dte ptp clock
NET: dwmac: Make dwmac reset unconditional
net: Zero terminate ifr_name in dev_ifname().
wireless: wext: terminate ifr name coming from userspace
netfilter: fix netfilter_net_init() return
...
|
|
The caller to the driver marks GFP_NOIO allocations with help
of memalloc_noio-* calls now. This makes redundant to pass down
to the driver gfp flags, which can be GFP_KERNEL only.
The patch removes the gfp flags argument and updates all driver paths.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The function __mlx4_zone_remove_one_entry always returns zero. So
it is not necessary to check it.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't rely on kzalloc() always succeeding, so check its return value.
Suppresses the following smatch error:
mlxsw_sp_switchdev_event() error: potential null dereference
'switchdev_work->fdb_info.addr'. (kzalloc returns
null)
Fixes: af061378924f ("mlxsw: spectrum_switchdev: Add support for learning FDB through notification")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 10e23eb299fa ("mlxsw: spectrum: Remove support for bypass bridge
port attributes/vlan set") removed statements that used 'bridge_vlan',
but didn't remove the variable itself resulting in the following warning
with W=1:
warning: variable ‘bridge_vlan’ set but not used
[-Wunused-but-set-variable]
Remove the variable and suppress the warning.
Fixes: 10e23eb299fa ("mlxsw: spectrum: Remove support for bypass bridge port attributes/vlan set")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While working on IPv6 route replace I realized we can have a
use-after-free in IPv4 in case the replaced route is offloaded and the
only one using its FIB info.
The problem is that fib_table_insert() drops the reference on the FIB
info of the replaced routes which is eventually freed via call_rcu().
Since the driver doesn't hold a reference on this FIB info it can cause
a use-after-free when it tries to clear the RTNH_F_OFFLOAD flag stored
in fi->fib_flags.
After running the following commands in a loop for enough time with a
KASAN enabled kernel I finally got the below trace.
$ ip route add 192.168.50.0/24 via 192.168.200.1 dev enp3s0np3
$ ip route replace 192.168.50.0/24 dev enp3s0np5
$ ip route del 192.168.50.0/24 dev enp3s0np5
BUG: KASAN: use-after-free in mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
Read of size 4 at addr ffff8803717d9820 by task kworker/u4:2/55
[...]
? mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
? mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
? mlxsw_sp_router_neighs_update_work+0x1cd0/0x1ce0 [mlxsw_spectrum]
? mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
__asan_load4+0x61/0x80
mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
mlxsw_sp_fib_entry_offload_refresh+0xb6/0x370 [mlxsw_spectrum]
mlxsw_sp_router_fib_event_work+0xd1c/0x2780 [mlxsw_spectrum]
[...]
Freed by task 5131:
save_stack_trace+0x16/0x20
save_stack+0x46/0xd0
kasan_slab_free+0x70/0xc0
kfree+0x144/0x570
free_fib_info_rcu+0x2e7/0x410
rcu_process_callbacks+0x4f8/0xe30
__do_softirq+0x1d3/0x9e2
Fix this by taking a reference on the FIB info when creating the nexthop
group it represents and drop it when the group is destroyed.
Fixes: 599cf8f95f22 ("mlxsw: spectrum_router: Add support for route replace")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this patch the error path of mlxsw_sp_nexthop_init() is symmetric
with mlxsw_sp_nexthop_fini(). Noticed during code review.
Fixes: a8c970142798 ("mlxsw: spectrum_router: Refactor nexthop init routine")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new IPSec offload code introduced a build error:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ipsec_rxtx.o: In function `mlx5e_ipsec_build_inverse_table':
ipsec_rxtx.c:(.text+0x556): undefined reference
Another patch was added on top to fix the build error, but
that introduced a new bug, as we now use the remainder of
the division rather than the result.
This makes it use the correct helper function instead.
Fixes: 5dfd87b67cd9 ("net/mlx5: IPSec, Fix 64-bit division on 32-bit builds")
Fixes: 2ac9cfe78223 ("net/mlx5e: IPSec, Add Innova IPSec offload TX data path")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Latest change in open-lldp code uses bytes 6-11 of perm_addr buffer
as the Ethernet source address for the host TLV packet.
Since our driver does not fill these bytes, they stay at zero and
the open-lldp code ends up sending the TLV packet with zero source
address and the switch drops this packet.
The fix is to initialize these bytes to 0xff. The open-lldp code
considers 0xff:ff:ff:ff:ff:ff as the invalid address and falls back to
use the host's mac address as the Ethernet source address.
Fixes: 3a6a931dfb8e ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently it is not possible to build just one .o file inside
a subdirectory, because the subdirectories lack a Makefile.
Add a Makefile to the mlx5 subdirectories.
Fixes: e29341fb3a5b ("net/mlx5: FPGA, Add basic support for Innova")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Both the ethernet and FPGA portions of MLX5 now require the wq functions,
and we get a link error when CONFIG_MLX5_CORE_EN is disabled:
drivers/net/ethernet/mellanox/mlx5/core/fpga/conn.o: In function `mlx5_fpga_conn_create_cq':
conn.c:(.text+0x10b3): undefined reference to `mlx5_cqwq_create'
conn.c:(.text+0x10c6): undefined reference to `mlx5_cqwq_get_size'
conn.c:(.text+0x12bc): undefined reference to `mlx5_cqwq_destroy'
Build wq.o even if MLX5_CORE_EN is not selected.
Fixes: 537a50574175 ("net/mlx5: FPGA, Add high-speed connection routines")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix warnings when building with -Wall:
drivers/net/ethernet/mellanox/mlx5/core/fpga/ipsec.c:313:36: warning: cast to restricted __be32
drivers/net/ethernet/mellanox/mlx5/core/fpga/ipsec.c:314:37: warning: cast to restricted __be32
Fixes: bebb23e6cb02 ("net/mlx5: Accel, Add IPSec acceleration interface")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix warning when building with -Wall:
drivers/net/ethernet/mellanox/mlx5/core/fpga/core.c:105:5: warning: symbol 'mlx5_fpga_device_brb' was not declared. Should it be static?
Fixes: c43051d72a8d ("net/mlx5: FPGA, Add SBU bypass and reset flows")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix warnings when building 386 kernel:
>> ERROR: "__udivdi3" [drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.ko] undefined!
Fixes: 2ac9cfe78223 ("net/mlx5e: IPSec, Add Innova IPSec offload TX data path")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix warnings when building with -Wall:
drivers/net/ethernet/mellanox/mlx5/core/lib/gid.c:38:6: warning: symbol 'mlx5_init_reserved_gids' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx5/core/lib/gid.c:47:6: warning: symbol 'mlx5_cleanup_reserved_gids' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx5/core/lib/gid.c:55:5: warning: symbol 'mlx5_core_reserve_gids' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx5/core/lib/gid.c:79:6: warning: symbol 'mlx5_core_unreserve_gids' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx5/core/lib/gid.c:92:5: warning: symbol 'mlx5_core_reserved_gid_alloc' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx5/core/lib/gid.c:109:6: warning: symbol 'mlx5_core_reserved_gid_free' was not declared. Should it be static?
Fixes: 52ec462eca9b ("net/mlx5: Add reserved-gids support")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
