summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel
AgeCommit message (Collapse)AuthorFilesLines
2022-07-12i40e: Fix VF's MAC Address change on VMNorbert Zulinski1-0/+4
[ Upstream commit fed0d9f13266a22ce1fc9a97521ef9cdc6271a23 ] Clear VF MAC from parent PF and remove VF filter from VSI when both conditions are true: -VIRTCHNL_VF_OFFLOAD_USO is not used -VM MAC was not set from PF level It affects older version of IAVF and it allow them to change MAC Address on VM, newer IAVF won't change their behaviour. Previously it wasn't possible to change VF's MAC Address on VM because there is flag on IAVF driver that won't allow to change MAC Address if this address is given from PF driver. Fixes: 155f0ac2c96b ("iavf: allow permanent MAC address to change") Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com> Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-07-12i40e: Fix dropped jumbo frames statisticsLukasz Cieplicki4-0/+103
[ Upstream commit 1adb1563e7b7ec659379a18e607e8bc3522d8a78 ] Dropped packets caused by too large frames were not included in dropped RX packets statistics. Issue was caused by not reading the GL_RXERR1 register. That register stores count of packet which was have been dropped due to too large size. Fix it by reading GL_RXERR1 register for each interface. Repro steps: Send a packet larger than the set MTU to SUT Observe rx statists: ethtool -S <interface> | grep rx | grep -v ": 0" Fixes: 41a9e55c89be ("i40e: add missing VSI statistics") Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-29igb: Make DMA faster when CPU is active on the PCIe linkKai-Heng Feng1-7/+5
[ Upstream commit 4e0effd9007ea0be31f7488611eb3824b4541554 ] Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which will be significantly lower when 1) ASPM is disabled or 2) SoC package c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx speed can reach to ~950Mbps. According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC", "DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so set it to 1b for "DMA is considered idle when there is no Rx or Tx AND when there are no TLPs indicating that CPU is active detected on the PCIe link (such as the host executes CSR or Configuration register read or write operation)" and performing Tx should also fall under "active CPU on PCIe link" case. In addition to that, commit b6e0c419f040 ("igb: Move DMA Coalescing init code to separate function.") seems to wrongly changed from enabling E1000_PCIEMISC_LX_DECISION to disabling it, also fix that. Fixes: b6e0c419f040 ("igb: Move DMA Coalescing init code to separate function.") Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-29ice: ethtool: Prohibit improper channel config for DCBAnatolii Gerasymenko2-5/+47
[ Upstream commit a632b2a4c920ce5af29410fb091f7ee6d2e77dc6 ] Do not allow setting less channels, than Traffic Classes there are via ethtool. There must be at least one channel per Traffic Class. If you set less channels, than Traffic Classes there are, then during ice_vsi_rebuild there would be allocated only the requested amount of tx/rx rings in ice_vsi_alloc_arrays. But later in ice_vsi_setup_q_map there would be requested at least one channel per Traffic Class. This results in setting num_rxq > alloc_rxq and num_txq > alloc_txq. Later, there would be a NULL pointer dereference in ice_vsi_map_rings_to_vectors, because we go beyond of rx_rings or tx_rings arrays. Change ice_set_channels() to return error if you try to allocate less channels, than Traffic Classes there are. Change ice_vsi_setup_q_map() and ice_vsi_setup_q_map_mqprio() to return status code instead of void. Add error handling for ice_vsi_setup_q_map() and ice_vsi_setup_q_map_mqprio() in ice_vsi_init() and ice_vsi_cfg_tc(). [53753.889983] INFO: Flow control is disabled for this traffic class (0) on this vsi. [53763.984862] BUG: unable to handle kernel NULL pointer dereference at 0000000000000028 [53763.992915] PGD 14b45f5067 P4D 0 [53763.996444] Oops: 0002 [#1] SMP NOPTI [53764.000312] CPU: 12 PID: 30661 Comm: ethtool Kdump: loaded Tainted: GOE --------- - - 4.18.0-240.el8.x86_64 #1 [53764.011825] Hardware name: Intel Corporation WilsonCity/WilsonCity, BIOS WLYDCRB1.SYS.0020.P21.2012150710 12/15/2020 [53764.022584] RIP: 0010:ice_vsi_map_rings_to_vectors+0x7e/0x120 [ice] [53764.029089] Code: 41 0d 0f b7 b7 12 05 00 00 0f b6 d0 44 29 de 44 0f b7 c6 44 01 c2 41 39 d0 7d 2d 4c 8b 47 28 44 0f b7 ce 83 c6 01 4f 8b 04 c8 <49> 89 48 28 4 c 8b 89 b8 01 00 00 4d 89 08 4c 89 81 b8 01 00 00 44 [53764.048379] RSP: 0018:ff550dd88ea47b20 EFLAGS: 00010206 [53764.053884] RAX: 0000000000000002 RBX: 0000000000000004 RCX: ff385ea42fa4a018 [53764.061301] RDX: 0000000000000006 RSI: 0000000000000005 RDI: ff385e9baeedd018 [53764.068717] RBP: 0000000000000010 R08: 0000000000000000 R09: 0000000000000004 [53764.076133] R10: 0000000000000002 R11: 0000000000000004 R12: 0000000000000000 [53764.083553] R13: 0000000000000000 R14: ff385e658fdd9000 R15: ff385e9baeedd018 [53764.090976] FS: 000014872c5b5740(0000) GS:ff385e847f100000(0000) knlGS:0000000000000000 [53764.099362] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [53764.105409] CR2: 0000000000000028 CR3: 0000000a820fa002 CR4: 0000000000761ee0 [53764.112851] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [53764.120301] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [53764.127747] PKRU: 55555554 [53764.130781] Call Trace: [53764.133564] ice_vsi_rebuild+0x611/0x870 [ice] [53764.138341] ice_vsi_recfg_qs+0x94/0x100 [ice] [53764.143116] ice_set_channels+0x1a8/0x3e0 [ice] [53764.147975] ethtool_set_channels+0x14e/0x240 [53764.152667] dev_ethtool+0xd74/0x2a10 [53764.156665] ? __mod_lruvec_state+0x44/0x110 [53764.161280] ? __mod_lruvec_state+0x44/0x110 [53764.165893] ? page_add_file_rmap+0x15/0x170 [53764.170518] ? inet_ioctl+0xd1/0x220 [53764.174445] ? netdev_run_todo+0x5e/0x290 [53764.178808] dev_ioctl+0xb5/0x550 [53764.182485] sock_do_ioctl+0xa0/0x140 [53764.186512] sock_ioctl+0x1a8/0x300 [53764.190367] ? selinux_file_ioctl+0x161/0x200 [53764.195090] do_vfs_ioctl+0xa4/0x640 [53764.199035] ksys_ioctl+0x60/0x90 [53764.202722] __x64_sys_ioctl+0x16/0x20 [53764.206845] do_syscall_64+0x5b/0x1a0 [53764.210887] entry_SYSCALL_64_after_hwframe+0x65/0xca Fixes: 87324e747fde ("ice: Implement ethtool ops for channels") Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-29ice: ethtool: advertise 1000M speeds properlyAnatolii Gerasymenko1-1/+38
[ Upstream commit c3d184c83ff4b80167e34edfc3d21df424bf27ff ] In current implementation ice_update_phy_type enables all link modes for selected speed. This approach doesn't work for 1000M speeds, because both copper (1000baseT) and optical (1000baseX) standards cannot be enabled at once. Fix this, by adding the function `ice_set_phy_type_from_speed()` for 1000M speeds. Fixes: 48cb27f2fd18 ("ice: Implement handlers for ethtool PHY/link operations") Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-29ice: Fix switchdev rules book keepingWojciech Drewek1-0/+1
[ Upstream commit 3578dc90013b1fa20da996cdadd8515802716132 ] Adding two filters with same matching criteria ends up with one rule in hardware with act = ICE_FWD_TO_VSI_LIST. In order to remove them properly we have to keep the information about vsi handle which is used in VSI bitmap (ice_adv_fltr_mgmt_list_entry::vsi_list_info::vsi_map). Fixes: 0d08a441fb1a ("ice: ndo_setup_tc implementation for PF") Reported-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-29ice: ignore protocol field in GTP offloadMarcin Szycik1-1/+3
[ Upstream commit d4ea6f6373ef56d1d795a24f1f5874f4a6019199 ] Commit 34a897758efe ("ice: Add support for inner etype in switchdev") added the ability to match on inner ethertype. A side effect of that change is that it is now impossible to add some filters for protocols which do not contain inner ethtype field. tc requires the protocol field to be specified when providing certain other options, e.g. src_ip. This is a problem in case of GTP - when user wants to specify e.g. src_ip, they also need to specify protocol in tc command (otherwise tc fails with: Illegal "src_ip"). Because GTP is a tunnel, the protocol field is treated as inner protocol. GTP does not contain inner ethtype field and the filter cannot be added. To fix this, ignore the ethertype field in case of GTP filters. Fixes: 9a225f81f540 ("ice: Support GTP-U and GTP-C offload in switchdev") Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-29igb: fix a use-after-free issue in igb_clean_tx_ringLorenzo Bianconi1-2/+5
[ Upstream commit 3f6a57ee8544ec3982f8a3cbcbf4aea7d47eb9ec ] Fix the following use-after-free bug in igb_clean_tx_ring routine when the NIC is running in XDP mode. The issue can be triggered redirecting traffic into the igb NIC and then closing the device while the traffic is flowing. [ 73.322719] CPU: 1 PID: 487 Comm: xdp_redirect Not tainted 5.18.3-apu2 #9 [ 73.330639] Hardware name: PC Engines APU2/APU2, BIOS 4.0.7 02/28/2017 [ 73.337434] RIP: 0010:refcount_warn_saturate+0xa7/0xf0 [ 73.362283] RSP: 0018:ffffc9000081f798 EFLAGS: 00010282 [ 73.367761] RAX: 0000000000000000 RBX: ffffc90000420f80 RCX: 0000000000000000 [ 73.375200] RDX: ffff88811ad22d00 RSI: ffff88811ad171e0 RDI: ffff88811ad171e0 [ 73.382590] RBP: 0000000000000900 R08: ffffffff82298f28 R09: 0000000000000058 [ 73.390008] R10: 0000000000000219 R11: ffffffff82280f40 R12: 0000000000000090 [ 73.397356] R13: ffff888102343a40 R14: ffff88810359e0e4 R15: 0000000000000000 [ 73.404806] FS: 00007ff38d31d740(0000) GS:ffff88811ad00000(0000) knlGS:0000000000000000 [ 73.413129] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 73.419096] CR2: 000055cff35f13f8 CR3: 0000000106391000 CR4: 00000000000406e0 [ 73.426565] Call Trace: [ 73.429087] <TASK> [ 73.431314] igb_clean_tx_ring+0x43/0x140 [igb] [ 73.436002] igb_down+0x1d7/0x220 [igb] [ 73.439974] __igb_close+0x3c/0x120 [igb] [ 73.444118] igb_xdp+0x10c/0x150 [igb] [ 73.447983] ? igb_pci_sriov_configure+0x70/0x70 [igb] [ 73.453362] dev_xdp_install+0xda/0x110 [ 73.457371] dev_xdp_attach+0x1da/0x550 [ 73.461369] do_setlink+0xfd0/0x10f0 [ 73.465166] ? __nla_validate_parse+0x89/0xc70 [ 73.469714] rtnl_setlink+0x11a/0x1e0 [ 73.473547] rtnetlink_rcv_msg+0x145/0x3d0 [ 73.477709] ? rtnl_calcit.isra.0+0x130/0x130 [ 73.482258] netlink_rcv_skb+0x8d/0x110 [ 73.486229] netlink_unicast+0x230/0x340 [ 73.490317] netlink_sendmsg+0x215/0x470 [ 73.494395] __sys_sendto+0x179/0x190 [ 73.498268] ? move_addr_to_user+0x37/0x70 [ 73.502547] ? __sys_getsockname+0x84/0xe0 [ 73.506853] ? netlink_setsockopt+0x1c1/0x4a0 [ 73.511349] ? __sys_setsockopt+0xc8/0x1d0 [ 73.515636] __x64_sys_sendto+0x20/0x30 [ 73.519603] do_syscall_64+0x3b/0x80 [ 73.523399] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 73.528712] RIP: 0033:0x7ff38d41f20c [ 73.551866] RSP: 002b:00007fff3b945a68 EFLAGS: 00000246 ORIG_RAX: 000000000000002c [ 73.559640] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007ff38d41f20c [ 73.567066] RDX: 0000000000000034 RSI: 00007fff3b945b30 RDI: 0000000000000003 [ 73.574457] RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000 [ 73.581852] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fff3b945ab0 [ 73.589179] R13: 0000000000000000 R14: 0000000000000003 R15: 00007fff3b945b30 [ 73.596545] </TASK> [ 73.598842] ---[ end trace 0000000000000000 ]--- Fixes: 9cbc948b5a20c ("igb: add XDP support") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Link: https://lore.kernel.org/r/e5c01d549dc37bff18e46aeabd6fb28a7bcf84be.1655388571.git.lorenzo@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-22ice: Fix memory corruption in VF driverPrzemyslaw Patynowski1-0/+5
[ Upstream commit efe41860008e57fb6b69855b4b93fdf34bc42798 ] Disable VF's RX/TX queues, when it's disabled. VF can have queues enabled, when it requests a reset. If PF driver assumes that VF is disabled, while VF still has queues configured, VF may unmap DMA resources. In such scenario device still can map packets to memory, which ends up silently corrupting it. Previously, VF driver could experience memory corruption, which lead to crash: [ 5119.170157] BUG: unable to handle kernel paging request at 00001b9780003237 [ 5119.170166] PGD 0 P4D 0 [ 5119.170173] Oops: 0002 [#1] PREEMPT_RT SMP PTI [ 5119.170181] CPU: 30 PID: 427592 Comm: kworker/u96:2 Kdump: loaded Tainted: G W I --------- - - 4.18.0-372.9.1.rt7.166.el8.x86_64 #1 [ 5119.170189] Hardware name: Dell Inc. PowerEdge R740/014X06, BIOS 2.3.10 08/15/2019 [ 5119.170193] Workqueue: iavf iavf_adminq_task [iavf] [ 5119.170219] RIP: 0010:__page_frag_cache_drain+0x5/0x30 [ 5119.170238] Code: 0f 0f b6 77 51 85 f6 74 07 31 d2 e9 05 df ff ff e9 90 fe ff ff 48 8b 05 49 db 33 01 eb b4 0f 1f 80 00 00 00 00 0f 1f 44 00 00 <f0> 29 77 34 74 01 c3 48 8b 07 f6 c4 80 74 0f 0f b6 77 51 85 f6 74 [ 5119.170244] RSP: 0018:ffffa43b0bdcfd78 EFLAGS: 00010282 [ 5119.170250] RAX: ffffffff896b3e40 RBX: ffff8fb282524000 RCX: 0000000000000002 [ 5119.170254] RDX: 0000000049000000 RSI: 0000000000000000 RDI: 00001b9780003203 [ 5119.170259] RBP: ffff8fb248217b00 R08: 0000000000000022 R09: 0000000000000009 [ 5119.170262] R10: 2b849d6300000000 R11: 0000000000000020 R12: 0000000000000000 [ 5119.170265] R13: 0000000000001000 R14: 0000000000000009 R15: 0000000000000000 [ 5119.170269] FS: 0000000000000000(0000) GS:ffff8fb1201c0000(0000) knlGS:0000000000000000 [ 5119.170274] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 5119.170279] CR2: 00001b9780003237 CR3: 00000008f3e1a003 CR4: 00000000007726e0 [ 5119.170283] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 5119.170286] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 5119.170290] PKRU: 55555554 [ 5119.170292] Call Trace: [ 5119.170298] iavf_clean_rx_ring+0xad/0x110 [iavf] [ 5119.170324] iavf_free_rx_resources+0xe/0x50 [iavf] [ 5119.170342] iavf_free_all_rx_resources.part.51+0x30/0x40 [iavf] [ 5119.170358] iavf_virtchnl_completion+0xd8a/0x15b0 [iavf] [ 5119.170377] ? iavf_clean_arq_element+0x210/0x280 [iavf] [ 5119.170397] iavf_adminq_task+0x126/0x2e0 [iavf] [ 5119.170416] process_one_work+0x18f/0x420 [ 5119.170429] worker_thread+0x30/0x370 [ 5119.170437] ? process_one_work+0x420/0x420 [ 5119.170445] kthread+0x151/0x170 [ 5119.170452] ? set_kthread_struct+0x40/0x40 [ 5119.170460] ret_from_fork+0x35/0x40 [ 5119.170477] Modules linked in: iavf sctp ip6_udp_tunnel udp_tunnel mlx4_en mlx4_core nfp tls vhost_net vhost vhost_iotlb tap tun xt_CHECKSUM ipt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables nfnetlink bridge stp llc rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache sunrpc intel_rapl_msr iTCO_wdt iTCO_vendor_support dell_smbios wmi_bmof dell_wmi_descriptor dcdbas kvm_intel kvm irqbypass intel_rapl_common isst_if_common skx_edac irdma nfit libnvdimm x86_pkg_temp_thermal i40e intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul ghash_clmulni_intel ib_uverbs rapl ipmi_ssif intel_cstate intel_uncore mei_me pcspkr acpi_ipmi ib_core mei lpc_ich i2c_i801 ipmi_si ipmi_devintf wmi ipmi_msghandler acpi_power_meter xfs libcrc32c sd_mod t10_pi sg mgag200 drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ice ahci drm libahci crc32c_intel libata tg3 megaraid_sas [ 5119.170613] i2c_algo_bit dm_mirror dm_region_hash dm_log dm_mod fuse [last unloaded: iavf] [ 5119.170627] CR2: 00001b9780003237 Fixes: ec4f5a436bdf ("ice: Check if VF is disabled for Opcode and other operations") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Co-developed-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-22ice: Fix queue config fail handlingPrzemyslaw Patynowski1-27/+26
[ Upstream commit be2af71496a54a7195ac62caba6fab49cfe5006c ] Disable VF's RX/TX queues, when VIRTCHNL_OP_CONFIG_VSI_QUEUES fail. Not disabling them might lead to scenario, where PF driver leaves VF queues enabled, when VF's VSI failed queue config. In this scenario VF should not have RX/TX queues enabled. If PF failed to set up VF's queues, VF will reset due to TX timeouts in VF driver. Initialize iterator 'i' to -1, so if error happens prior to configuring queues then error path code will not disable queue 0. Loop that configures queues will is using same iterator, so error path code will only disable queues that were configured. Fixes: 77ca27c41705 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap") Suggested-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-22ice: Sync VLAN filtering features for DVMRoman Storozhenko1-18/+31
[ Upstream commit 9542ef4fba8c73e176b8aa18a8adf04aecb889e5 ] VLAN filtering features, that is C-Tag and S-Tag, in DVM mode must be both enabled or disabled. In case of turning off/on only one of the features, another feature must be turned off/on automatically with issuing an appropriate message to the kernel log. Fixes: 1babaf77f49d ("ice: Advertise 802.1ad VLAN filtering and offloads for PF netdev") Signed-off-by: Roman Storozhenko <roman.storozhenko@intel.com> Co-developed-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com> Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-22ice: Fix PTP TX timestamp offset calculationMichal Michalik2-1/+32
[ Upstream commit 71a579f0d3777a704355e6f1572dfba92a9b58b2 ] The offset was being incorrectly calculated for E822 - that led to collisions in choosing TX timestamp register location when more than one port was trying to use timestamping mechanism. In E822 one quad is being logically split between ports, so quad 0 is having trackers for ports 0-3, quad 1 ports 4-7 etc. Each port should have separate memory location for tracking timestamps. Due to error for example ports 1 and 2 had been assigned to quad 0 with same offset (0), while port 1 should have offset 0 and 1 offset 16. Fix it by correctly calculating quad offset. Fixes: 3a7496234d17 ("ice: implement basic E822 PTP support") Signed-off-by: Michal Michalik <michal.michalik@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-22iavf: Fix issue with MAC address of VF shown as zeroMichal Wilczynski1-1/+1
[ Upstream commit 645603844270b69175899268be68b871295764fe ] After reinitialization of iavf, ice driver gets VIRTCHNL_OP_ADD_ETH_ADDR message with incorrectly set type of MAC address. Hardware address should have is_primary flag set as true. This way ice driver knows what it has to set as a MAC address. Check if the address is primary in iavf_add_filter function and set flag accordingly. To test set all-zero MAC on a VF. This triggers iavf re-initialization and VIRTCHNL_OP_ADD_ETH_ADDR message gets sent to PF. For example: ip link set dev ens785 vf 0 mac 00:00:00:00:00:00 This triggers re-initialization of iavf. New MAC should be assigned. Now check if MAC is non-zero: ip link show dev ens785 Fixes: a3e839d539e0 ("iavf: Add usage of new virtchnl format to set default MAC") Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-22i40e: Fix call trace in setup_tx_descriptorsAleksandr Loktionov1-8/+17
[ Upstream commit fd5855e6b1358e816710afee68a1d2bc685176ca ] After PF reset and ethtool -t there was call trace in dmesg sometimes leading to panic. When there was some time, around 5 seconds, between reset and test there were no errors. Problem was that pf reset calls i40e_vsi_close in prep_for_reset and ethtool -t calls i40e_vsi_close in diag_test. If there was not enough time between those commands the second i40e_vsi_close starts before previous i40e_vsi_close was done which leads to crash. Add check to diag_test if pf is in reset and don't start offline tests if it is true. Add netif_info("testing failed") into unhappy path of i40e_diag_test() Fixes: e17bc411aea8 ("i40e: Disable offline diagnostics if VFs are enabled") Fixes: 510efb2682b3 ("i40e: Fix ethtool offline diagnostic with netqueues") Signed-off-by: Michal Jaron <michalx.jaron@intel.com> Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-22i40e: Fix calculating the number of queue pairsGrzegorz Szczurek1-1/+1
[ Upstream commit 0bb050670ac90a167ecfa3f9590f92966c9a3677 ] If ADQ is enabled for a VF, then actual number of queue pair is a number of currently available traffic classes for this VF. Without this change the configuration of the Rx/Tx queues fails with error. Fixes: d29e0d233e0d ("i40e: missing input validation on VF message handling by the PF") Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-22i40e: Fix adding ADQ filter to TC0Grzegorz Szczurek1-0/+5
[ Upstream commit c3238d36c3a2be0a29a9d848d6c51e1b14be6692 ] Procedure of configure tc flower filters erroneously allows to create filters on TC0 where unfiltered packets are also directed by default. Issue was caused by insufficient checks of hw_tc parameter specifying the hardware traffic class to pass matching packets to. Fix checking hw_tc parameter which blocks creation of filters on TC0. Fixes: 2f4b411a3d67 ("i40e: Enable cloud filters via tc-flower") Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-06-14ixgbe: fix unexpected VLAN Rx in promisc mode on VFOlivier Matz1-2/+2
commit 7bb0fb7c63df95d6027dc50d6af3bc3bbbc25483 upstream. When the promiscuous mode is enabled on a VF, the IXGBE_VMOLR_VPE bit (VLAN Promiscuous Enable) is set. This means that the VF will receive packets whose VLAN is not the same than the VLAN of the VF. For instance, in this situation: ┌────────┐ ┌────────┐ ┌────────┐ │ │ │ │ │ │ │ │ │ │ │ │ │ VF0├────┤VF1 VF2├────┤VF3 │ │ │ │ │ │ │ └────────┘ └────────┘ └────────┘ VM1 VM2 VM3 vf 0: vlan 1000 vf 1: vlan 1000 vf 2: vlan 1001 vf 3: vlan 1001 If we tcpdump on VF3, we see all the packets, even those transmitted on vlan 1000. This behavior prevents to bridge VF1 and VF2 in VM2, because it will create a loop: packets transmitted on VF1 will be received by VF2 and vice-versa, and bridged again through the software bridge. This patch remove the activation of VLAN Promiscuous when a VF enables the promiscuous mode. However, the IXGBE_VMOLR_UPE bit (Unicast Promiscuous) is kept, so that a VF receives all packets that has the same VLAN, whatever the destination MAC address. Fixes: 8443c1a4b192 ("ixgbe, ixgbevf: Add new mbox API xcast mode") Cc: stable@vger.kernel.org Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Olivier Matz <olivier.matz@6wind.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-06-14ixgbe: fix bcast packets Rx on VF after promisc removalOlivier Matz1-2/+2
commit 803e9895ea2b0fe80bc85980ae2d7a7e44037914 upstream. After a VF requested to remove the promiscuous flag on an interface, the broadcast packets are not received anymore. This breaks some protocols like ARP. In ixgbe_update_vf_xcast_mode(), we should keep the IXGBE_VMOLR_BAM bit (Broadcast Accept) on promiscuous removal. This flag is already set by default in ixgbe_set_vmolr() on VF reset. Fixes: 8443c1a4b192 ("ixgbe, ixgbevf: Add new mbox API xcast mode") Cc: stable@vger.kernel.org Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Olivier Matz <olivier.matz@6wind.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-06-09ice: always check VF VSI pointer valuesJacob Keller6-7/+77
[ Upstream commit baeb705fd6a7245cc1fa69ed991a9cffdf44a174 ] The ice_get_vf_vsi function can return NULL in some cases, such as if handling messages during a reset where the VSI is being removed and recreated. Several places throughout the driver do not bother to check whether this VSI pointer is valid. Static analysis tools maybe report issues because they detect paths where a potentially NULL pointer could be dereferenced. Fix this by checking the return value of ice_get_vf_vsi everywhere. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-05-18igb: skip phy status check where unavailableKevin Mitchell1-1/+2
igb_read_phy_reg() will silently return, leaving phy_data untouched, if hw->ops.read_reg isn't set. Depending on the uninitialized value of phy_data, this led to the phy status check either succeeding immediately or looping continuously for 2 seconds before emitting a noisy err-level timeout. This message went out to the console even though there was no actual problem. Instead, first check if there is read_reg function pointer. If not, proceed without trying to check the phy status register. Fixes: b72f3f72005d ("igb: When GbE link up, wait for Remote receiver status condition") Signed-off-by: Kevin Mitchell <kevmitch@arista.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-17ice: Fix interrupt moderation settings getting clearedMichal Wilczynski2-11/+16
Adaptive-rx and Adaptive-tx are interrupt moderation settings that can be enabled/disabled using ethtool: ethtool -C ethX adaptive-rx on/off adaptive-tx on/off Unfortunately those settings are getting cleared after changing number of queues, or in ethtool world 'channels': ethtool -L ethX rx 1 tx 1 Clearing was happening due to introduction of bit fields in ice_ring_container struct. This way only itr_setting bits were rebuilt during ice_vsi_rebuild_set_coalesce(). Introduce an anonymous struct of bitfields and create a union to refer to them as a single variable. This way variable can be easily saved and restored. Fixes: 61dc79ced7aa ("ice: Restore interrupt throttle settings after VSI rebuild") Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-17ice: fix possible under reporting of ethtool Tx and Rx statisticsPaul Greenwalt1-3/+4
The hardware statistics counters are not cleared during resets so the drivers first access is to initialize the baseline and then subsequent reads are for reporting the counters. The statistics counters are read during the watchdog subtask when the interface is up. If the baseline is not initialized before the interface is up, then there can be a brief window in which some traffic can be transmitted/received before the initial baseline reading takes place. Directly initialize ethtool statistics in driver open so the baseline will be initialized when the interface is up, and any dropped packets incremented before the interface is up won't be reported. Fixes: 28dc1b86f8ea9 ("ice: ignore dropped packets during init") Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-17ice: fix crash when writing timestamp on RX ringsArkadiusz Kubalewski1-4/+15
Do not allow to write timestamps on RX rings if PF is being configured. When PF is being configured RX rings can be freed or rebuilt. If at the same time timestamps are updated, the kernel will crash by dereferencing null RX ring pointer. PID: 1449 TASK: ff187d28ed658040 CPU: 34 COMMAND: "ice-ptp-0000:51" #0 [ff1966a94a713bb0] machine_kexec at ffffffff9d05a0be #1 [ff1966a94a713c08] __crash_kexec at ffffffff9d192e9d #2 [ff1966a94a713cd0] crash_kexec at ffffffff9d1941bd #3 [ff1966a94a713ce8] oops_end at ffffffff9d01bd54 #4 [ff1966a94a713d08] no_context at ffffffff9d06bda4 #5 [ff1966a94a713d60] __bad_area_nosemaphore at ffffffff9d06c10c #6 [ff1966a94a713da8] do_page_fault at ffffffff9d06cae4 #7 [ff1966a94a713de0] page_fault at ffffffff9da0107e [exception RIP: ice_ptp_update_cached_phctime+91] RIP: ffffffffc076db8b RSP: ff1966a94a713e98 RFLAGS: 00010246 RAX: 16e3db9c6b7ccae4 RBX: ff187d269dd3c180 RCX: ff187d269cd4d018 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ff187d269cfcc644 R8: ff187d339b9641b0 R9: 0000000000000000 R10: 0000000000000002 R11: 0000000000000000 R12: ff187d269cfcc648 R13: ffffffff9f128784 R14: ffffffff9d101b70 R15: ff187d269cfcc640 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #8 [ff1966a94a713ea0] ice_ptp_periodic_work at ffffffffc076dbef [ice] #9 [ff1966a94a713ee0] kthread_worker_fn at ffffffff9d101c1b #10 [ff1966a94a713f10] kthread at ffffffff9d101b4d #11 [ff1966a94a713f50] ret_from_fork at ffffffff9da0023f Fixes: 77a781155a65 ("ice: enable receive hardware timestamping") Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Reviewed-by: Michal Schmidt <mschmidt@redhat.com> Tested-by: Dave Cain <dcain@redhat.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-12i40e: i40e_main: fix a missing check on list iteratorXiaomeng Tong1-13/+14
The bug is here: ret = i40e_add_macvlan_filter(hw, ch->seid, vdev->dev_addr, &aq_err); The list iterator 'ch' will point to a bogus position containing HEAD if the list is empty or no element is found. This case must be checked before any use of the iterator, otherwise it will lead to a invalid memory access. To fix this bug, use a new variable 'iter' as the list iterator, while use the origin variable 'ch' as a dedicated pointer to point to the found element. Cc: stable@vger.kernel.org Fixes: 1d8d80b4e4ff6 ("i40e: Add macvlan support on i40e") Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20220510204846.2166999-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-06ice: fix PTP stale Tx timestamps cleanupMichal Michalik1-2/+8
Read stale PTP Tx timestamps from PHY on cleanup. After running out of Tx timestamps request handlers, hardware (HW) stops reporting finished requests. Function ice_ptp_tx_tstamp_cleanup() used to only clean up stale handlers in driver and was leaving the hardware registers not read. Not reading stale PTP Tx timestamps prevents next interrupts from arriving and makes timestamping unusable. Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices") Signed-off-by: Michal Michalik <michal.michalik@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-06ice: clear stale Tx queue settings before configuringAnatolii Gerasymenko1-18/+50
The iAVF driver uses 3 virtchnl op codes to communicate with the PF regarding the VF Tx queues: * VIRTCHNL_OP_CONFIG_VSI_QUEUES configures the hardware and firmware logic for the Tx queues * VIRTCHNL_OP_ENABLE_QUEUES configures the queue interrupts * VIRTCHNL_OP_DISABLE_QUEUES disables the queue interrupts and Tx rings. There is a bug in the iAVF driver due to the race condition between VF reset request and shutdown being executed in parallel. This leads to a break in logic and VIRTCHNL_OP_DISABLE_QUEUES is not being sent. If this occurs, the PF driver never cleans up the Tx queues. This results in leaving behind stale Tx queue settings in the hardware and firmware. The most obvious outcome is that upon the next VIRTCHNL_OP_CONFIG_VSI_QUEUES, the PF will fail to program the Tx scheduler node due to a lack of space. We need to protect ICE driver against such situation. To fix this, make sure we clear existing stale settings out when handling VIRTCHNL_OP_CONFIG_VSI_QUEUES. This ensures we remove the previous settings. Calling ice_vf_vsi_dis_single_txq should be safe as it will do nothing if the queue is not configured. The function already handles the case when the Tx queue is not currently configured and exits with a 0 return in that case. Fixes: 7ad15440acf8 ("ice: Refactor VIRTCHNL_OP_CONFIG_VSI_QUEUES handling") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-06ice: Fix race during aux device (un)pluggingIvan Vecera3-8/+20
Function ice_plug_aux_dev() assigns pf->adev field too early prior aux device initialization and on other side ice_unplug_aux_dev() starts aux device deinit and at the end assigns NULL to pf->adev. This is wrong because pf->adev should always be non-NULL only when aux device is fully initialized and ready. This wrong order causes a crash when ice_send_event_to_aux() call occurs because that function depends on non-NULL value of pf->adev and does not assume that aux device is half-initialized or half-destroyed. After order correction the race window is tiny but it is still there, as Leon mentioned and manipulation with pf->adev needs to be protected by mutex. Fix (un-)plugging functions so pf->adev field is set after aux device init and prior aux device destroy and protect pf->adev assignment by new mutex. This mutex is also held during ice_send_event_to_aux() call to ensure that aux device is valid during that call. Note that device lock used ice_send_event_to_aux() needs to be kept to avoid race with aux drv unload. Reproducer: cycle=1 while :;do echo "#### Cycle: $cycle" ip link set ens7f0 mtu 9000 ip link add bond0 type bond mode 1 miimon 100 ip link set bond0 up ifenslave bond0 ens7f0 ip link set bond0 mtu 9000 ethtool -L ens7f0 combined 1 ip link del bond0 ip link set ens7f0 mtu 1500 sleep 1 let cycle++ done In short when the device is added/removed to/from bond the aux device is unplugged/plugged. When MTU of the device is changed an event is sent to aux device asynchronously. This can race with (un)plugging operation and because pf->adev is set too early (plug) or too late (unplug) the function ice_send_event_to_aux() can touch uninitialized or destroyed fields. In the case of crash below pf->adev->dev.mutex. Crash: [ 53.372066] bond0: (slave ens7f0): making interface the new active one [ 53.378622] bond0: (slave ens7f0): Enslaving as an active interface with an u p link [ 53.386294] IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready [ 53.549104] bond0: (slave ens7f1): Enslaving as a backup interface with an up link [ 54.118906] ice 0000:ca:00.0 ens7f0: Number of in use tx queues changed inval idating tc mappings. Priority traffic classification disabled! [ 54.233374] ice 0000:ca:00.1 ens7f1: Number of in use tx queues changed inval idating tc mappings. Priority traffic classification disabled! [ 54.248204] bond0: (slave ens7f0): Releasing backup interface [ 54.253955] bond0: (slave ens7f1): making interface the new active one [ 54.274875] bond0: (slave ens7f1): Releasing backup interface [ 54.289153] bond0 (unregistering): Released all slaves [ 55.383179] MII link monitoring set to 100 ms [ 55.398696] bond0: (slave ens7f0): making interface the new active one [ 55.405241] BUG: kernel NULL pointer dereference, address: 0000000000000080 [ 55.405289] bond0: (slave ens7f0): Enslaving as an active interface with an u p link [ 55.412198] #PF: supervisor write access in kernel mode [ 55.412200] #PF: error_code(0x0002) - not-present page [ 55.412201] PGD 25d2ad067 P4D 0 [ 55.412204] Oops: 0002 [#1] PREEMPT SMP NOPTI [ 55.412207] CPU: 0 PID: 403 Comm: kworker/0:2 Kdump: loaded Tainted: G S 5.17.0-13579-g57f2d6540f03 #1 [ 55.429094] bond0: (slave ens7f1): Enslaving as a backup interface with an up link [ 55.430224] Hardware name: Dell Inc. PowerEdge R750/06V45N, BIOS 1.4.4 10/07/ 2021 [ 55.430226] Workqueue: ice ice_service_task [ice] [ 55.468169] RIP: 0010:mutex_unlock+0x10/0x20 [ 55.472439] Code: 0f b1 13 74 96 eb e0 4c 89 ee eb d8 e8 79 54 ff ff 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 65 48 8b 04 25 40 ef 01 00 31 d2 <f0> 48 0f b1 17 75 01 c3 e9 e3 fe ff ff 0f 1f 00 0f 1f 44 00 00 48 [ 55.491186] RSP: 0018:ff4454230d7d7e28 EFLAGS: 00010246 [ 55.496413] RAX: ff1a79b208b08000 RBX: ff1a79b2182e8880 RCX: 0000000000000001 [ 55.503545] RDX: 0000000000000000 RSI: ff4454230d7d7db0 RDI: 0000000000000080 [ 55.510678] RBP: ff1a79d1c7e48b68 R08: ff4454230d7d7db0 R09: 0000000000000041 [ 55.517812] R10: 00000000000000a5 R11: 00000000000006e6 R12: ff1a79d1c7e48bc0 [ 55.524945] R13: 0000000000000000 R14: ff1a79d0ffc305c0 R15: 0000000000000000 [ 55.532076] FS: 0000000000000000(0000) GS:ff1a79d0ffc00000(0000) knlGS:0000000000000000 [ 55.540163] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 55.545908] CR2: 0000000000000080 CR3: 00000003487ae003 CR4: 0000000000771ef0 [ 55.553041] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 55.560173] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 55.567305] PKRU: 55555554 [ 55.570018] Call Trace: [ 55.572474] <TASK> [ 55.574579] ice_service_task+0xaab/0xef0 [ice] [ 55.579130] process_one_work+0x1c5/0x390 [ 55.583141] ? process_one_work+0x390/0x390 [ 55.587326] worker_thread+0x30/0x360 [ 55.590994] ? process_one_work+0x390/0x390 [ 55.595180] kthread+0xe6/0x110 [ 55.598325] ? kthread_complete_and_exit+0x20/0x20 [ 55.603116] ret_from_fork+0x1f/0x30 [ 55.606698] </TASK> Fixes: f9f5301e7e2d ("ice: Register auxiliary device to provide RDMA") Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Dave Ertman <david.m.ertman@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-28ixgbe: ensure IPsec VF<->PF compatibilityLeon Romanovsky1-1/+2
The VF driver can forward any IPsec flags and such makes the function is not extendable and prone to backward/forward incompatibility. If new software runs on VF, it won't know that PF configured something completely different as it "knows" only XFRM_OFFLOAD_INBOUND flag. Fixes: eda0333ac293 ("ixgbe: add VF IPsec management") Reviewed-by: Raed Salem <raeds@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Shannon Nelson <snelson@pensando.io> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20220427173152.443102-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-26ice: fix use-after-free when deinitializing mailbox snapshotJacob Keller1-1/+1
During ice_sriov_configure, if num_vfs is 0, we are being asked by the kernel to remove all VFs. The driver first de-initializes the snapshot before freeing all the VFs. This results in a use-after-free BUG detected by KASAN. The bug occurs because the snapshot can still be accessed until all VFs are removed. Fix this by freeing all the VFs first before calling ice_mbx_deinit_snapshot. [ +0.032591] ================================================================== [ +0.000021] BUG: KASAN: use-after-free in ice_mbx_vf_state_handler+0x1c3/0x410 [ice] [ +0.000315] Write of size 28 at addr ffff889908eb6f28 by task kworker/55:2/1530996 [ +0.000029] CPU: 55 PID: 1530996 Comm: kworker/55:2 Kdump: loaded Tainted: G S I 5.17.0-dirty #1 [ +0.000022] Hardware name: Dell Inc. PowerEdge R740/0923K0, BIOS 1.6.13 12/17/2018 [ +0.000013] Workqueue: ice ice_service_task [ice] [ +0.000279] Call Trace: [ +0.000012] <TASK> [ +0.000011] dump_stack_lvl+0x33/0x42 [ +0.000030] print_report.cold.13+0xb2/0x6b3 [ +0.000028] ? ice_mbx_vf_state_handler+0x1c3/0x410 [ice] [ +0.000295] kasan_report+0xa5/0x120 [ +0.000026] ? __switch_to_asm+0x21/0x70 [ +0.000024] ? ice_mbx_vf_state_handler+0x1c3/0x410 [ice] [ +0.000298] kasan_check_range+0x183/0x1e0 [ +0.000019] memset+0x1f/0x40 [ +0.000018] ice_mbx_vf_state_handler+0x1c3/0x410 [ice] [ +0.000304] ? ice_conv_link_speed_to_virtchnl+0x160/0x160 [ice] [ +0.000297] ? ice_vsi_dis_spoofchk+0x40/0x40 [ice] [ +0.000305] ice_is_malicious_vf+0x1aa/0x250 [ice] [ +0.000303] ? ice_restore_all_vfs_msi_state+0x160/0x160 [ice] [ +0.000297] ? __mutex_unlock_slowpath.isra.15+0x410/0x410 [ +0.000022] ? ice_debug_cq+0xb7/0x230 [ice] [ +0.000273] ? __kasan_slab_alloc+0x2f/0x90 [ +0.000022] ? memset+0x1f/0x40 [ +0.000017] ? do_raw_spin_lock+0x119/0x1d0 [ +0.000022] ? rwlock_bug.part.2+0x60/0x60 [ +0.000024] __ice_clean_ctrlq+0x3a6/0xd60 [ice] [ +0.000273] ? newidle_balance+0x5b1/0x700 [ +0.000026] ? ice_print_link_msg+0x2f0/0x2f0 [ice] [ +0.000271] ? update_cfs_group+0x1b/0x140 [ +0.000018] ? load_balance+0x1260/0x1260 [ +0.000022] ? ice_process_vflr_event+0x27/0x130 [ice] [ +0.000301] ice_service_task+0x136e/0x1470 [ice] [ +0.000281] process_one_work+0x3b4/0x6c0 [ +0.000030] worker_thread+0x65/0x660 [ +0.000023] ? __kthread_parkme+0xe4/0x100 [ +0.000021] ? process_one_work+0x6c0/0x6c0 [ +0.000020] kthread+0x179/0x1b0 [ +0.000018] ? kthread_complete_and_exit+0x20/0x20 [ +0.000022] ret_from_fork+0x22/0x30 [ +0.000026] </TASK> [ +0.000018] Allocated by task 10742: [ +0.000013] kasan_save_stack+0x1c/0x40 [ +0.000018] __kasan_kmalloc+0x84/0xa0 [ +0.000016] kmem_cache_alloc_trace+0x16c/0x2e0 [ +0.000015] intel_iommu_probe_device+0xeb/0x860 [ +0.000015] __iommu_probe_device+0x9a/0x2f0 [ +0.000016] iommu_probe_device+0x43/0x270 [ +0.000015] iommu_bus_notifier+0xa7/0xd0 [ +0.000015] blocking_notifier_call_chain+0x90/0xc0 [ +0.000017] device_add+0x5f3/0xd70 [ +0.000014] pci_device_add+0x404/0xa40 [ +0.000015] pci_iov_add_virtfn+0x3b0/0x550 [ +0.000016] sriov_enable+0x3bb/0x600 [ +0.000013] ice_ena_vfs+0x113/0xa79 [ice] [ +0.000293] ice_sriov_configure.cold.17+0x21/0xe0 [ice] [ +0.000291] sriov_numvfs_store+0x160/0x200 [ +0.000015] kernfs_fop_write_iter+0x1db/0x270 [ +0.000018] new_sync_write+0x21d/0x330 [ +0.000013] vfs_write+0x376/0x410 [ +0.000013] ksys_write+0xba/0x150 [ +0.000012] do_syscall_64+0x3a/0x80 [ +0.000012] entry_SYSCALL_64_after_hwframe+0x44/0xae [ +0.000028] Freed by task 10742: [ +0.000011] kasan_save_stack+0x1c/0x40 [ +0.000015] kasan_set_track+0x21/0x30 [ +0.000016] kasan_set_free_info+0x20/0x30 [ +0.000012] __kasan_slab_free+0x104/0x170 [ +0.000016] kfree+0x9b/0x470 [ +0.000013] devres_destroy+0x1c/0x20 [ +0.000015] devm_kfree+0x33/0x40 [ +0.000012] ice_mbx_deinit_snapshot+0x39/0x70 [ice] [ +0.000295] ice_sriov_configure+0xb0/0x260 [ice] [ +0.000295] sriov_numvfs_store+0x1bc/0x200 [ +0.000015] kernfs_fop_write_iter+0x1db/0x270 [ +0.000016] new_sync_write+0x21d/0x330 [ +0.000012] vfs_write+0x376/0x410 [ +0.000012] ksys_write+0xba/0x150 [ +0.000012] do_syscall_64+0x3a/0x80 [ +0.000012] entry_SYSCALL_64_after_hwframe+0x44/0xae [ +0.000024] Last potentially related work creation: [ +0.000010] kasan_save_stack+0x1c/0x40 [ +0.000016] __kasan_record_aux_stack+0x98/0xa0 [ +0.000013] insert_work+0x34/0x160 [ +0.000015] __queue_work+0x20e/0x650 [ +0.000016] queue_work_on+0x4c/0x60 [ +0.000015] nf_nat_masq_schedule+0x297/0x2e0 [nf_nat] [ +0.000034] masq_device_event+0x5a/0x60 [nf_nat] [ +0.000031] raw_notifier_call_chain+0x5f/0x80 [ +0.000017] dev_close_many+0x1d6/0x2c0 [ +0.000015] unregister_netdevice_many+0x4e3/0xa30 [ +0.000015] unregister_netdevice_queue+0x192/0x1d0 [ +0.000014] iavf_remove+0x8f9/0x930 [iavf] [ +0.000058] pci_device_remove+0x65/0x110 [ +0.000015] device_release_driver_internal+0xf8/0x190 [ +0.000017] pci_stop_bus_device+0xb5/0xf0 [ +0.000014] pci_stop_and_remove_bus_device+0xe/0x20 [ +0.000016] pci_iov_remove_virtfn+0x19c/0x230 [ +0.000015] sriov_disable+0x4f/0x170 [ +0.000014] ice_free_vfs+0x9a/0x490 [ice] [ +0.000306] ice_sriov_configure+0xb8/0x260 [ice] [ +0.000294] sriov_numvfs_store+0x1bc/0x200 [ +0.000015] kernfs_fop_write_iter+0x1db/0x270 [ +0.000016] new_sync_write+0x21d/0x330 [ +0.000012] vfs_write+0x376/0x410 [ +0.000012] ksys_write+0xba/0x150 [ +0.000012] do_syscall_64+0x3a/0x80 [ +0.000012] entry_SYSCALL_64_after_hwframe+0x44/0xae [ +0.000025] The buggy address belongs to the object at ffff889908eb6f00 which belongs to the cache kmalloc-96 of size 96 [ +0.000016] The buggy address is located 40 bytes inside of 96-byte region [ffff889908eb6f00, ffff889908eb6f60) [ +0.000026] The buggy address belongs to the physical page: [ +0.000010] page:00000000b7e99a2e refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1908eb6 [ +0.000016] flags: 0x57ffffc0000200(slab|node=1|zone=2|lastcpupid=0x1fffff) [ +0.000024] raw: 0057ffffc0000200 ffffea0069d9fd80 dead000000000002 ffff88810004c780 [ +0.000015] raw: 0000000000000000 0000000000200020 00000001ffffffff 0000000000000000 [ +0.000009] page dumped because: kasan: bad access detected [ +0.000016] Memory state around the buggy address: [ +0.000012] ffff889908eb6e00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc [ +0.000014] ffff889908eb6e80: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc [ +0.000014] >ffff889908eb6f00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc [ +0.000011] ^ [ +0.000013] ffff889908eb6f80: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc [ +0.000013] ffff889908eb7000: fa fb fb fb fb fb fb fb fc fc fc fc fa fb fb fb [ +0.000012] ================================================================== Fixes: 0891c89674e8 ("ice: warn about potentially malicious VFs") Reported-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-26ice: wait 5 s for EMP reset after firmware flashPetr Oros1-0/+3
We need to wait 5 s for EMP reset after firmware flash. Code was extracted from OOT driver (ice v1.8.3 downloaded from sourceforge). Without this wait, fw_activate let card in inconsistent state and recoverable only by second flash/activate. Flash was tested on these fw's: From -> To 3.00 -> 3.10/3.20 3.10 -> 3.00/3.20 3.20 -> 3.00/3.10 Reproducer: [root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin Preparing to flash [fw.mgmt] Erasing [fw.mgmt] Erasing done [fw.mgmt] Flashing 100% [fw.mgmt] Flashing done 100% [fw.undi] Erasing [fw.undi] Erasing done [fw.undi] Flashing 100% [fw.undi] Flashing done 100% [fw.netlist] Erasing [fw.netlist] Erasing done [fw.netlist] Flashing 100% [fw.netlist] Flashing done 100% Activate new firmware by devlink reload [root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate reload_actions_performed: fw_activate [root@host ~]# ip link show ens7f0 71: ens7f0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000 link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff altname enp202s0f0 dmesg after flash: [ 55.120788] ice: Copyright (c) 2018, Intel Corporation. [ 55.274734] ice 0000:ca:00.0: Get PHY capabilities failed status = -5, continuing anyway [ 55.569797] ice 0000:ca:00.0: The DDP package was successfully loaded: ICE OS Default Package version 1.3.28.0 [ 55.603629] ice 0000:ca:00.0: Get PHY capability failed. [ 55.608951] ice 0000:ca:00.0: ice_init_nvm_phy_type failed: -5 [ 55.647348] ice 0000:ca:00.0: PTP init successful [ 55.675536] ice 0000:ca:00.0: DCB is enabled in the hardware, max number of TCs supported on this port are 8 [ 55.685365] ice 0000:ca:00.0: FW LLDP is disabled, DCBx/LLDP in SW mode. [ 55.692179] ice 0000:ca:00.0: Commit DCB Configuration to the hardware [ 55.701382] ice 0000:ca:00.0: 126.024 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x8 link at 0000:c9:02.0 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link) Reboot doesn’t help, only second flash/activate with OOT or patched driver put card back in consistent state. After patch: [root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin Preparing to flash [fw.mgmt] Erasing [fw.mgmt] Erasing done [fw.mgmt] Flashing 100% [fw.mgmt] Flashing done 100% [fw.undi] Erasing [fw.undi] Erasing done [fw.undi] Flashing 100% [fw.undi] Flashing done 100% [fw.netlist] Erasing [fw.netlist] Erasing done [fw.netlist] Flashing 100% [fw.netlist] Flashing done 100% Activate new firmware by devlink reload [root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate reload_actions_performed: fw_activate [root@host ~]# ip link show ens7f0 19: ens7f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000 link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff altname enp202s0f0 Fixes: 399e27dbbd9e94 ("ice: support immediate firmware activation via devlink reload") Signed-off-by: Petr Oros <poros@redhat.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-26ice: Protect vf_state check by cfg_lock in ice_vc_process_vf_msg()Ivan Vecera1-7/+5
Previous patch labelled "ice: Fix incorrect locking in ice_vc_process_vf_msg()" fixed an issue with ignored messages sent by VF driver but a small race window still left. Recently caught trace during 'ip link set ... vf 0 vlan ...' operation: [ 7332.995625] ice 0000:3b:00.0: Clearing port VLAN on VF 0 [ 7333.001023] iavf 0000:3b:01.0: Reset indication received from the PF [ 7333.007391] iavf 0000:3b:01.0: Scheduling reset task [ 7333.059575] iavf 0000:3b:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 3 [ 7333.059626] ice 0000:3b:00.0: Invalid message from VF 0, opcode 3, len 4, error -1 Setting of VLAN for VF causes a reset of the affected VF using ice_reset_vf() function that runs with cfg_lock taken: 1. ice_notify_vf_reset() informs IAVF driver that reset is needed and IAVF schedules its own reset procedure 2. Bit ICE_VF_STATE_DIS is set in vf->vf_state 3. Misc initialization steps 4. ice_sriov_post_vsi_rebuild() -> ice_vf_set_initialized() and that clears ICE_VF_STATE_DIS in vf->vf_state Step 3 is mentioned race window because IAVF reset procedure runs in parallel and one of its step is sending of VIRTCHNL_OP_GET_VF_RESOURCES message (opcode==3). This message is handled in ice_vc_process_vf_msg() and if it is received during the mentioned race window then it's marked as invalid and error is returned to VF driver. Protect vf_state check in ice_vc_process_vf_msg() by cfg_lock to avoid this race condition. Fixes: e6ba5273d4ed ("ice: Fix race conditions between virtchnl handling and VF ndo ops") Tested-by: Fei Liu <feliu@redhat.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-26ice: Fix incorrect locking in ice_vc_process_vf_msg()Ivan Vecera1-14/+7
Usage of mutex_trylock() in ice_vc_process_vf_msg() is incorrect because message sent from VF is ignored and never processed. Use mutex_lock() instead to fix the issue. It is safe because this mutex is used to prevent races between VF related NDOs and handlers processing request messages from VF and these handlers are running in ice_service_task() context. Additionally move this mutex lock prior ice_vc_is_opcode_allowed() call to avoid potential races during allowlist access. Fixes: e6ba5273d4ed ("ice: Fix race conditions between virtchnl handling and VF ndo ops") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-16Merge branch '1GbE' of ↵Jakub Kicinski4-7/+27
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2022-04-13 This series contains updates to igc and e1000e drivers. Sasha removes waiting for hardware semaphore as it could cause an infinite loop and changes usleep_range() calls done under atomic context to udelay() for igc. For e1000e, he changes some variables from u16 to u32 to prevent possible overflow of values. Vinicius disables PTM when going to suspend as it is causing hang issues on some platforms for igc. * '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: e1000e: Fix possible overflow in LTR decoding igc: Fix suspending when PTM is active igc: Fix BUG: scheduling while atomic igc: Fix infinite loop in release_swfw_sync ==================== Link: https://lore.kernel.org/r/20220413170814.2066855-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-14ice: Fix memory leak in ice_get_orom_civd_data()Jianglei Nie1-0/+1
A memory chunk was allocated for orom_data in ice_get_orom_civd_data() by vzmalloc(). But when ice_read_flash_module() fails, the allocated memory is not freed, which will lead to a memory leak. We can fix it by freeing the orom_data when ce_read_flash_module() fails. Fixes: af18d8866c80 ("ice: reduce time to read Option ROM CIVD data") Signed-off-by: Jianglei Nie <niejianglei2021@163.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-14ice: fix crash in switchdev modeWojciech Drewek1-1/+2
Below steps end up with crash: - modprobe ice - devlink dev eswitch set $PF1_PCI mode switchdev - echo 64 > /sys/class/net/$PF1/device/sriov_numvfs - rmmod ice Calling ice_eswitch_port_start_xmit while the process of removing VFs is in progress ends up with NULL pointer dereference. That's because PR netdev is not released but some resources are already freed. Fix it by checking if ICE_VF_DIS bit is set. Call trace: [ 1379.595146] BUG: kernel NULL pointer dereference, address: 0000000000000040 [ 1379.595284] #PF: supervisor read access in kernel mode [ 1379.595410] #PF: error_code(0x0000) - not-present page [ 1379.595535] PGD 0 P4D 0 [ 1379.595657] Oops: 0000 [#1] PREEMPT SMP PTI [ 1379.595783] CPU: 4 PID: 974 Comm: NetworkManager Kdump: loaded Tainted: G OE 5.17.0-rc8_mrq_dev-queue+ #12 [ 1379.595926] Hardware name: Intel Corporation S1200SP/S1200SP, BIOS S1200SP.86B.03.01.0042.013020190050 01/30/2019 [ 1379.596063] RIP: 0010:ice_eswitch_port_start_xmit+0x46/0xd0 [ice] [ 1379.596292] Code: c7 c8 09 00 00 e8 9a c9 fc ff 84 c0 0f 85 82 00 00 00 4c 89 e7 e8 ca 70 fe ff 48 8b 7d 58 48 89 c3 48 85 ff 75 5e 48 8b 53 20 <8b> 42 40 85 c0 74 78 8d 48 01 f0 0f b1 4a 40 75 f2 0f b6 95 84 00 [ 1379.596456] RSP: 0018:ffffaba0c0d7bad0 EFLAGS: 00010246 [ 1379.596584] RAX: ffff969c14c71680 RBX: ffff969c14c71680 RCX: 000100107a0f0000 [ 1379.596715] RDX: 0000000000000000 RSI: ffff969b9d631000 RDI: 0000000000000000 [ 1379.596846] RBP: ffff969c07b46500 R08: ffff969becfca8ac R09: 0000000000000001 [ 1379.596977] R10: 0000000000000004 R11: ffffaba0c0d7bbec R12: ffff969b9d631000 [ 1379.597106] R13: ffffffffc08357a0 R14: ffff969c07b46500 R15: ffff969b9d631000 [ 1379.597237] FS: 00007f72c0e25c80(0000) GS:ffff969f13500000(0000) knlGS:0000000000000000 [ 1379.597414] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1379.597562] CR2: 0000000000000040 CR3: 000000012b316006 CR4: 00000000003706e0 [ 1379.597713] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 1379.597863] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 1379.598015] Call Trace: [ 1379.598153] <TASK> [ 1379.598294] dev_hard_start_xmit+0xd9/0x220 [ 1379.598444] sch_direct_xmit+0x8a/0x340 [ 1379.598592] __dev_queue_xmit+0xa3c/0xd30 [ 1379.598739] ? packet_parse_headers+0xb4/0xf0 [ 1379.598890] packet_sendmsg+0xa15/0x1620 [ 1379.599038] ? __check_object_size+0x46/0x140 [ 1379.599186] sock_sendmsg+0x5e/0x60 [ 1379.599330] ____sys_sendmsg+0x22c/0x270 [ 1379.599474] ? import_iovec+0x17/0x20 [ 1379.599622] ? sendmsg_copy_msghdr+0x59/0x90 [ 1379.599771] ___sys_sendmsg+0x81/0xc0 [ 1379.599917] ? __pollwait+0xd0/0xd0 [ 1379.600061] ? preempt_count_add+0x68/0xa0 [ 1379.600210] ? _raw_write_lock_irq+0x1a/0x40 [ 1379.600369] ? ep_done_scan+0xc9/0x110 [ 1379.600494] ? _raw_spin_unlock_irqrestore+0x25/0x40 [ 1379.600622] ? preempt_count_add+0x68/0xa0 [ 1379.600747] ? _raw_spin_lock_irq+0x1a/0x40 [ 1379.600899] ? __fget_light+0x8f/0x110 [ 1379.601024] __sys_sendmsg+0x49/0x80 [ 1379.601148] ? release_ds_buffers+0x50/0xe0 [ 1379.601274] do_syscall_64+0x3b/0x90 [ 1379.601399] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 1379.601525] RIP: 0033:0x7f72c1e2e35d Fixes: f5396b8a663f ("ice: switchdev slow path") Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com> Reported-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-14ice: allow creating VFs for !CONFIG_NET_SWITCHDEVMaciej Fijalkowski1-1/+1
Currently for !CONFIG_NET_SWITCHDEV kernel builds it is not possible to create VFs properly as call to ice_eswitch_configure() returns -EOPNOTSUPP for us. This is because CONFIG_ICE_SWITCHDEV depends on CONFIG_NET_SWITCHDEV. Change the ice_eswitch_configure() implementation for !CONFIG_ICE_SWITCHDEV to return 0 instead -EOPNOTSUPP and let ice_ena_vfs() finish its work properly. CC: Grzegorz Nitka <grzegorz.nitka@intel.com> Fixes: 1a1c40df2e80 ("ice: set and release switchdev environment") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-14ice: xsk: check if Rx ring was filled up to the endMaciej Fijalkowski1-1/+6
__ice_alloc_rx_bufs_zc() checks if a number of the descriptors to be allocated would cause the ring wrap. In that case, driver will issue two calls to xsk_buff_alloc_batch() - one that will fill the ring up to the end and the second one that will start with filling descriptors from the beginning of the ring. ice_fill_rx_descs() is a wrapper for taking care of what xsk_buff_alloc_batch() gave back to the driver. It works in a best effort approach, so for example when driver asks for 64 buffers, ice_fill_rx_descs() could assign only 32. Such case needs to be checked when ring is being filled up to the end, because in that situation ntu might not reached the end of the ring. Fix the ring wrap by checking if nb_buffs_extra has the expected value. If not, bump ntu and go directly to tail update. Fixes: 3876ff525de7 ("ice: xsk: Handle SW XDP ring wrap and bump tail more often") Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Shwetha Nagaraju <Shwetha.nagaraju@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-13e1000e: Fix possible overflow in LTR decodingSasha Neftin1-2/+2
When we decode the latency and the max_latency, u16 value may not fit the required size and could lead to the wrong LTR representation. Scaling is represented as: scale 0 - 1 (2^(5*0)) = 2^0 scale 1 - 32 (2^(5 *1))= 2^5 scale 2 - 1024 (2^(5 *2)) =2^10 scale 3 - 32768 (2^(5 *3)) =2^15 scale 4 - 1048576 (2^(5 *4)) = 2^20 scale 5 - 33554432 (2^(5 *4)) = 2^25 scale 4 and scale 5 required 20 and 25 bits respectively. scale 6 reserved. Replace the u16 type with the u32 type and allow corrected LTR representation. Cc: stable@vger.kernel.org Fixes: 44a13a5d99c7 ("e1000e: Fix the max snoop/no-snoop latency for 10M") Reported-by: James Hutchinson <jahutchinson99@googlemail.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=215689 Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Tested-by: James Hutchinson <jahutchinson99@googlemail.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-13igc: Fix suspending when PTM is activeVinicius Costa Gomes1-1/+14
Some mainboard/CPU combinations, in particular, Alder Lake-S with a W680 mainboard, have shown problems (system hangs usually, no kernel logs) with suspend/resume when PCIe PTM is enabled and active. In some cases, it could be reproduced when removing the igc module. The best we can do is to stop PTM dialogs from the downstream/device side before the interface is brought down. PCIe PTM will be re-enabled when the interface is being brought up. Fixes: a90ec8483732 ("igc: Add support for PTP getcrosststamp()") Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Acked-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-13igc: Fix BUG: scheduling while atomicSasha Neftin1-2/+2
Replace usleep_range() method with udelay() method to allow atomic contexts in low-level MDIO access functions. The following issue can be seen by doing the following: $ modprobe -r bonding $ modprobe -v bonding max_bonds=1 mode=1 miimon=100 use_carrier=0 $ ip link set bond0 up $ ifenslave bond0 eth0 eth1 [ 982.357308] BUG: scheduling while atomic: kworker/u64:0/9/0x00000002 [ 982.364431] INFO: lockdep is turned off. [ 982.368824] Modules linked in: bonding sctp ip6_udp_tunnel udp_tunnel mlx4_ib ib_uverbs ib_core mlx4_en mlx4_core nfp tls sunrpc intel_rapl_msr iTCO_wdt iTCO_vendor_support mxm_wmi dcdbas intel_rapl_common sb_edac x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel rapl intel_cstate intel_uncore pcspkr lpc_ich mei_me ipmi_ssif mei ipmi_si ipmi_devintf ipmi_msghandler wmi acpi_power_meter xfs libcrc32c sr_mod cdrom sd_mod t10_pi sg mgag200 drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm ahci libahci crc32c_intel libata i2c_algo_bit tg3 megaraid_sas igc dm_mirror dm_region_hash dm_log dm_mod [last unloaded: bonding] [ 982.437941] CPU: 25 PID: 9 Comm: kworker/u64:0 Kdump: loaded Tainted: G W --------- - - 4.18.0-348.el8.x86_64+debug #1 [ 982.451333] Hardware name: Dell Inc. PowerEdge R730/0H21J3, BIOS 2.7.0 12/005/2017 [ 982.459791] Workqueue: bond0 bond_mii_monitor [bonding] [ 982.465622] Call Trace: [ 982.468355] dump_stack+0x8e/0xd0 [ 982.472056] __schedule_bug.cold.60+0x3a/0x60 [ 982.476919] __schedule+0x147b/0x1bc0 [ 982.481007] ? firmware_map_remove+0x16b/0x16b [ 982.485967] ? hrtimer_fixup_init+0x40/0x40 [ 982.490625] schedule+0xd9/0x250 [ 982.494227] schedule_hrtimeout_range_clock+0x10d/0x2c0 [ 982.500058] ? hrtimer_nanosleep_restart+0x130/0x130 [ 982.505598] ? hrtimer_init_sleeper_on_stack+0x90/0x90 [ 982.511332] ? usleep_range+0x88/0x130 [ 982.515514] ? recalibrate_cpu_khz+0x10/0x10 [ 982.520279] ? ktime_get+0xab/0x1c0 [ 982.524175] ? usleep_range+0x88/0x130 [ 982.528355] usleep_range+0xdd/0x130 [ 982.532344] ? console_conditional_schedule+0x30/0x30 [ 982.537987] ? igc_put_hw_semaphore+0x17/0x60 [igc] [ 982.543432] igc_read_phy_reg_gpy+0x111/0x2b0 [igc] [ 982.548887] igc_phy_has_link+0xfa/0x260 [igc] [ 982.553847] ? igc_get_phy_id+0x210/0x210 [igc] [ 982.558894] ? lock_acquire+0x34d/0x890 [ 982.563187] ? lock_downgrade+0x710/0x710 [ 982.567659] ? rcu_read_unlock+0x50/0x50 [ 982.572039] igc_check_for_copper_link+0x106/0x210 [igc] [ 982.577970] ? igc_config_fc_after_link_up+0x840/0x840 [igc] [ 982.584286] ? rcu_read_unlock+0x50/0x50 [ 982.588661] ? lock_release+0x591/0xb80 [ 982.592939] ? lock_release+0x591/0xb80 [ 982.597220] igc_has_link+0x113/0x330 [igc] [ 982.601887] ? lock_downgrade+0x710/0x710 [ 982.606362] igc_ethtool_get_link+0x6d/0x90 [igc] [ 982.611614] bond_check_dev_link+0x131/0x2c0 [bonding] [ 982.617350] ? bond_time_in_interval+0xd0/0xd0 [bonding] [ 982.623277] ? rcu_read_lock_held+0x62/0xc0 [ 982.627944] ? rcu_read_lock_sched_held+0xe0/0xe0 [ 982.633198] bond_mii_monitor+0x314/0x2500 [bonding] [ 982.638738] ? lock_contended+0x880/0x880 [ 982.643214] ? bond_miimon_link_change+0xa0/0xa0 [bonding] [ 982.649336] ? lock_acquire+0x34d/0x890 [ 982.653615] ? lock_downgrade+0x710/0x710 [ 982.658089] ? debug_object_deactivate+0x221/0x340 [ 982.663436] ? rcu_read_unlock+0x50/0x50 [ 982.667811] ? debug_print_object+0x2b0/0x2b0 [ 982.672672] ? __switch_to_asm+0x41/0x70 [ 982.677049] ? __switch_to_asm+0x35/0x70 [ 982.681426] ? _raw_spin_unlock_irq+0x24/0x40 [ 982.686288] ? trace_hardirqs_on+0x20/0x195 [ 982.690956] ? _raw_spin_unlock_irq+0x24/0x40 [ 982.695818] process_one_work+0x8f0/0x1770 [ 982.700390] ? pwq_dec_nr_in_flight+0x320/0x320 [ 982.705443] ? debug_show_held_locks+0x50/0x50 [ 982.710403] worker_thread+0x87/0xb40 [ 982.714489] ? process_one_work+0x1770/0x1770 [ 982.719349] kthread+0x344/0x410 [ 982.722950] ? kthread_insert_work_sanity_check+0xd0/0xd0 [ 982.728975] ret_from_fork+0x3a/0x50 Fixes: 5586838fe9ce ("igc: Add code for PHY support") Reported-by: Corinna Vinschen <vinschen@redhat.com> Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Corinna Vinschen <vinschen@redhat.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-13igc: Fix infinite loop in release_swfw_syncSasha Neftin1-2/+9
An infinite loop may occur if we fail to acquire the HW semaphore, which is needed for resource release. This will typically happen if the hardware is surprise-removed. At this stage there is nothing to do, except log an error and quit. Fixes: c0071c7aa5fe ("igc: Add HW initialization code") Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-08Revert "iavf: Fix deadlock occurrence during resetting VF interface"Mateusz Palczewski1-5/+2
This change caused a regression with resetting while changing network namespaces. By clearing the IFF_UP flag, the kernel now thinks it has fully closed the device. This reverts commit 0cc318d2e8408bc0ffb4662a0c3e5e57005ac6ff. Fixes: 0cc318d2e840 ("iavf: Fix deadlock occurrence during resetting VF interface") Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-08ice: arfs: fix use-after-free when freeing @rx_cpu_rmapAlexander Lobakin3-18/+14
The CI testing bots triggered the following splat: [ 718.203054] BUG: KASAN: use-after-free in free_irq_cpu_rmap+0x53/0x80 [ 718.206349] Read of size 4 at addr ffff8881bd127e00 by task sh/20834 [ 718.212852] CPU: 28 PID: 20834 Comm: sh Kdump: loaded Tainted: G S W IOE 5.17.0-rc8_nextqueue-devqueue-02643-g23f3121aca93 #1 [ 718.219695] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0012.070720200218 07/07/2020 [ 718.223418] Call Trace: [ 718.227139] [ 718.230783] dump_stack_lvl+0x33/0x42 [ 718.234431] print_address_description.constprop.9+0x21/0x170 [ 718.238177] ? free_irq_cpu_rmap+0x53/0x80 [ 718.241885] ? free_irq_cpu_rmap+0x53/0x80 [ 718.245539] kasan_report.cold.18+0x7f/0x11b [ 718.249197] ? free_irq_cpu_rmap+0x53/0x80 [ 718.252852] free_irq_cpu_rmap+0x53/0x80 [ 718.256471] ice_free_cpu_rx_rmap.part.11+0x37/0x50 [ice] [ 718.260174] ice_remove_arfs+0x5f/0x70 [ice] [ 718.263810] ice_rebuild_arfs+0x3b/0x70 [ice] [ 718.267419] ice_rebuild+0x39c/0xb60 [ice] [ 718.270974] ? asm_sysvec_apic_timer_interrupt+0x12/0x20 [ 718.274472] ? ice_init_phy_user_cfg+0x360/0x360 [ice] [ 718.278033] ? delay_tsc+0x4a/0xb0 [ 718.281513] ? preempt_count_sub+0x14/0xc0 [ 718.284984] ? delay_tsc+0x8f/0xb0 [ 718.288463] ice_do_reset+0x92/0xf0 [ice] [ 718.292014] ice_pci_err_resume+0x91/0xf0 [ice] [ 718.295561] pci_reset_function+0x53/0x80 <...> [ 718.393035] Allocated by task 690: [ 718.433497] Freed by task 20834: [ 718.495688] Last potentially related work creation: [ 718.568966] The buggy address belongs to the object at ffff8881bd127e00 which belongs to the cache kmalloc-96 of size 96 [ 718.574085] The buggy address is located 0 bytes inside of 96-byte region [ffff8881bd127e00, ffff8881bd127e60) [ 718.579265] The buggy address belongs to the page: [ 718.598905] Memory state around the buggy address: [ 718.601809] ffff8881bd127d00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc [ 718.604796] ffff8881bd127d80: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc [ 718.607794] >ffff8881bd127e00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc [ 718.610811] ^ [ 718.613819] ffff8881bd127e80: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc [ 718.617107] ffff8881bd127f00: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc This is due to that free_irq_cpu_rmap() is always being called *after* (devm_)free_irq() and thus it tries to work with IRQ descs already freed. For example, on device reset the driver frees the rmap right before allocating a new one (the splat above). Make rmap creation and freeing function symmetrical with {request,free}_irq() calls i.e. do that on ifup/ifdown instead of device probe/remove/resume. These operations can be performed independently from the actual device aRFS configuration. Also, make sure ice_vsi_free_irq() clears IRQ affinity notifiers only when aRFS is disabled -- otherwise, CPU rmap sets and clears its own and they must not be touched manually. Fixes: 28bf26724fdb0 ("ice: Implement aRFS") Co-developed-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Tested-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-05ice: clear cmd_type_offset_bsz for TX ringsMaciej Fijalkowski1-1/+1
Currently when XDP rings are created, each descriptor gets its DD bit set, which turns out to be the wrong approach as it can lead to a situation where more descriptors get cleaned than it was supposed to, e.g. when AF_XDP busy poll is run with a large batch size. In this situation, the driver would request for more buffers than it is able to handle. Fix this by not setting the DD bits in ice_xdp_alloc_setup_rings(). They should be initialized to zero instead. Fixes: 9610bd988df9 ("ice: optimize XDP_TX workloads") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-05ice: xsk: fix VSI state check in ice_xsk_wakeup()Maciej Fijalkowski1-1/+1
ICE_DOWN is dedicated for pf->state. Check for ICE_VSI_DOWN being set on vsi->state in ice_xsk_wakeup(). Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-05ice: synchronize_rcu() when terminating ringsMaciej Fijalkowski3-3/+7
Unfortunately, the ice driver doesn't respect the RCU critical section that XSK wakeup is surrounded with. To fix this, add synchronize_rcu() calls to paths that destroy resources that might be in use. This was addressed in other AF_XDP ZC enabled drivers, for reference see for example commit b3873a5be757 ("net/i40e: Fix concurrency issues between config flow and XSK") Fixes: efc2214b6047 ("ice: Add support for XDP") Fixes: 2d4238f55697 ("ice: Add support for AF_XDP") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-04-05ice: Do not skip not enabled queues in ice_vc_dis_qs_msgAnatolii Gerasymenko1-2/+2
Disable check for queue being enabled in ice_vc_dis_qs_msg, because there could be a case when queues were created, but were not enabled. We still need to delete those queues. Normal workflow for VF looks like: Enable path: VIRTCHNL_OP_ADD_ETH_ADDR (opcode 10) VIRTCHNL_OP_CONFIG_VSI_QUEUES (opcode 6) VIRTCHNL_OP_ENABLE_QUEUES (opcode 8) Disable path: VIRTCHNL_OP_DISABLE_QUEUES (opcode 9) VIRTCHNL_OP_DEL_ETH_ADDR (opcode 11) The issue appears only in stress conditions when VF is enabled and disabled very fast. Eventually there will be a case, when queues are created by VIRTCHNL_OP_CONFIG_VSI_QUEUES, but are not enabled by VIRTCHNL_OP_ENABLE_QUEUES. In turn, these queues are not deleted by VIRTCHNL_OP_DISABLE_QUEUES, because there is a check whether queues are enabled in ice_vc_dis_qs_msg. When we bring up the VF again, we will see the "Failed to set LAN Tx queue context" error during VIRTCHNL_OP_CONFIG_VSI_QUEUES step. This happens because old 16 queues were not deleted and VF requests to create 16 more, but ice_sched_get_free_qparent in ice_ena_vsi_txq would fail to find a parent node for first newly requested queue (because all nodes are allocated to 16 old queues). Testing Hints: Just enable and disable VF fast enough, so it would be disabled before reaching VIRTCHNL_OP_ENABLE_QUEUES. while true; do ip link set dev ens785f0v0 up sleep 0.065 # adjust delay value for you machine ip link set dev ens785f0v0 down done Fixes: 77ca27c41705 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap") Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Alice Michael <alice.michael@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-04-05ice: Set txq_teid to ICE_INVAL_TEID on ring creationAnatolii Gerasymenko1-0/+1
When VF is freshly created, but not brought up, ring->txq_teid value is by default set to 0. But 0 is a valid TEID. On some platforms the Root Node of Tx scheduler has a TEID = 0. This can cause issues as shown below. The proper way is to set ring->txq_teid to ICE_INVAL_TEID (0xFFFFFFFF). Testing Hints: echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs ip link set dev ens785f0v0 up ip link set dev ens785f0v0 down If we have freshly created VF and quickly turn it on and off, so there would be no time to reach VIRTCHNL_OP_CONFIG_VSI_QUEUES stage, then VIRTCHNL_OP_DISABLE_QUEUES stage will fail with error: [ 639.531454] disable queue 89 failed 14 [ 639.532233] Failed to disable LAN Tx queues, error: ICE_ERR_AQ_ERROR [ 639.533107] ice 0000:02:00.0: Failed to stop Tx ring 0 on VSI 5 The reason for the fail is that we are trying to send AQ command to delete queue 89, which has never been created and receive an "invalid argument" error from firmware. As this queue has never been created, it's teid and ring->txq_teid have default value 0. ice_dis_vsi_txq has a check against non-existent queues: node = ice_sched_find_node_by_teid(pi->root, q_teids[i]); if (!node) continue; But on some platforms the Root Node of Tx scheduler has a teid = 0. Hence, ice_sched_find_node_by_teid finds a node with teid = 0 (it is pi->root), and we go further to submit an erroneous request to firmware. Fixes: 37bb83901286 ("ice: Move common functions out of ice_main.c part 7/7") Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Alice Michael <alice.michael@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-04-01ice: Fix broken IFF_ALLMULTI handlingIvan Vecera3-38/+121
Handling of all-multicast flag and associated multicast promiscuous mode is broken in ice driver. When an user switches allmulticast flag on or off the driver checks whether any VLANs are configured over the interface (except default VLAN 0). If any extra VLANs are registered it enables multicast promiscuous mode for all these VLANs (including default VLAN 0) using ICE_SW_LKUP_PROMISC_VLAN look-up type. In this situation all multicast packets tagged with known VLAN ID or untagged are received and multicast packets tagged with unknown VLAN ID ignored. If no extra VLANs are registered (so only VLAN 0 exists) it enables multicast promiscuous mode for VLAN 0 and uses ICE_SW_LKUP_PROMISC look-up type. In this situation any multicast packets including tagged ones are received. The driver handles IFF_ALLMULTI in ice_vsi_sync_fltr() this way: ice_vsi_sync_fltr() { ... if (changed_flags & IFF_ALLMULTI) { if (netdev->flags & IFF_ALLMULTI) { if (vsi->num_vlans > 1) ice_set_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS); else ice_set_promisc(..., ICE_MCAST_PROMISC_BITS); } else { if (vsi->num_vlans > 1) ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS); else ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS); } } ... } The code above depends on value vsi->num_vlan that specifies number of VLANs configured over the interface (including VLAN 0) and this is problem because that value is modified in NDO callbacks ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid(). Scenario 1: 1. ip link set ens7f0 allmulticast on 2. ip link add vlan10 link ens7f0 type vlan id 10 3. ip link set ens7f0 allmulticast off 4. ip link set ens7f0 allmulticast on [1] In this scenario IFF_ALLMULTI is enabled and the driver calls ice_set_promisc(..., ICE_MCAST_PROMISC_BITS) that installs multicast promisc rule with non-VLAN look-up type. [2] Then VLAN with ID 10 is added and vsi->num_vlan incremented to 2 [3] Command switches IFF_ALLMULTI off and the driver calls ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS) but this call is effectively NOP because it looks for multicast promisc rules for VLAN 0 and VLAN 10 with VLAN look-up type but no such rules exist. So the all-multicast remains enabled silently in hardware. [4] Command tries to switch IFF_ALLMULTI on and the driver calls ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS) but this call fails (-EEXIST) because non-VLAN multicast promisc rule already exists. Scenario 2: 1. ip link add vlan10 link ens7f0 type vlan id 10 2. ip link set ens7f0 allmulticast on 3. ip link add vlan20 link ens7f0 type vlan id 20 4. ip link del vlan10 ; ip link del vlan20 5. ip link set ens7f0 allmulticast off [1] VLAN with ID 10 is added and vsi->num_vlan==2 [2] Command switches IFF_ALLMULTI on and driver installs multicast promisc rules with VLAN look-up type for VLAN 0 and 10 [3] VLAN with ID 20 is added and vsi->num_vlan==3 but no multicast promisc rules is added for this new VLAN so the interface does not receive MC packets from VLAN 20 [4] Both VLANs are removed but multicast rule for VLAN 10 remains installed so interface receives multicast packets from VLAN 10 [5] Command switches IFF_ALLMULTI off and because vsi->num_vlan is 1 the driver tries to remove multicast promisc rule for VLAN 0 with non-VLAN look-up that does not exist. All-multicast looks disabled from user point of view but it is partially enabled in HW (interface receives all multicast packets either untagged or tagged with VLAN ID 10) To resolve these issues the patch introduces these changes: 1. Adds handling for IFF_ALLMULTI to ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid() callbacks. So when VLAN is added/removed and IFF_ALLMULTI is enabled an appropriate multicast promisc rule for that VLAN ID is added/removed. 2. In ice_vlan_rx_add_vid() when first VLAN besides VLAN 0 is added so (vsi->num_vlan == 2) and IFF_ALLMULTI is enabled then look-up type for existing multicast promisc rule for VLAN 0 is updated to ICE_MCAST_VLAN_PROMISC_BITS. 3. In ice_vlan_rx_kill_vid() when last VLAN besides VLAN 0 is removed so (vsi->num_vlan == 1) and IFF_ALLMULTI is enabled then look-up type for existing multicast promisc rule for VLAN 0 is updated to ICE_MCAST_PROMISC_BITS. 4. Both ice_vlan_rx_{add,kill}_vid() have to run under ICE_CFG_BUSY bit protection to avoid races with ice_vsi_sync_fltr() that runs in ice_service_task() context. 5. Bit ICE_VSI_VLAN_FLTR_CHANGED is use-less and can be removed. 6. Error messages added to ice_fltr_*_vsi_promisc() helper functions to avoid them in their callers 7. Small improvements to increase readability Fixes: 5eda8afd6bcc ("ice: Add support for PF/VF promiscuous mode") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Alice Michael <alice.michael@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-01ice: Fix MAC address settingIvan Vecera1-2/+5
Commit 2ccc1c1ccc671b ("ice: Remove excess error variables") merged the usage of 'status' and 'err' variables into single one in function ice_set_mac_address(). Unfortunately this causes a regression when call of ice_fltr_add_mac() returns -EEXIST because this return value does not indicate an error in this case but value of 'err' remains to be -EEXIST till the end of the function and is returned to caller. Prior mentioned commit this does not happen because return value of ice_fltr_add_mac() was stored to 'status' variable first and if it was -EEXIST then 'err' remains to be zero. Fix the problem by reset 'err' to zero when ice_fltr_add_mac() returns -EEXIST. Fixes: 2ccc1c1ccc671b ("ice: Remove excess error variables") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Alexander Lobakin <alexandr.lobakin@intel.com> Signed-off-by: Alice Michael <alice.michael@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-20 09:03:21 +0300