| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 386228c694bf1e7a7688e44412cb33500b0ac585 upstream.
It was discovered that the Documentation lacks of a fundamental detail
on how to correctly change the MAX_FRAME_SIZE of the switch.
In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the
switch panics and cease to send any packet. This cause the mgmt ethernet
system to not receive any packet (the slow fallback still works) and
makes the device not reachable. To recover from this a switch reset is
required.
To correctly handle this, turn off the cpu ports before changing the
MAX_FRAME_SIZE and turn on again after the value is applied.
Fixes: f58d2598cf70 ("net: dsa: qca8k: implement the port MTU callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151122.10220-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 58bf4db695287c4bb2a5fc9fc12c78fdd4c36894 upstream.
Both PSFP stats and the port stats read by ocelot_check_stats_work() are
indirectly read through the same mechanism - write to STAT_CFG:STAT_VIEW,
read from SYS:STAT:CNT[n].
It's just that for port stats, we write STAT_VIEW with the index of the
port, and for PSFP stats, we write STAT_VIEW with the filter index.
So if we allow them to run concurrently, ocelot_check_stats_work() may
change the view from vsc9959_psfp_counters_get(), and vice versa.
Fixes: 7d4b564d6add ("net: dsa: felix: support psfp filter on vsc9959")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220629183007.3808130-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 16d584d2fc8f4ea36203af45a76becd7093586f1 upstream.
of_find_node_by_name() will decrease the refcount of its first arg and
we need a of_node_get() to keep refcount balance.
Fixes: 7d9ee2e8ff15 ("net: dsa: hellcreek: Add PTP status LEDs")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220622040621.4094304-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7c97bc0128b2eecc703106112679a69d446d1a12 upstream.
The pause settings reported by the PHY should also be applied to the GMII port
status override otherwise the switch will not generate pause frames towards the
link partner despite the advertisement saying otherwise.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220623030204.1966851-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 85467f7da18992311deafdbf32a8d163cb1e98d7 ]
The current mgmt ethernet timeout is set to 100ms. This value is too
big and would slow down any mdio command in case the mgmt ethernet
packet have some problems on the receiving part.
Reduce it to just 5ms to handle case when some operation are done on the
master port that would cause the mgmt ethernet to not work temporarily.
Fixes: 5950c7c0a68c ("net: dsa: qca8k: add support for mgmt read/write in Ethernet packet")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151633.11741-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 487994ff75880569d32504d7e70da8b3328e0693 ]
Since commit a18e6521a7d9 ("net: phylink: handle NA interface mode in
phylink_fwnode_phy_connect()"), phylib defaults to GMII when no phy-mode
or phy-connection-type property is specified in a DSA port node of the
device tree. The same commit caused a regression in rtl8365mb whereby
phylink would fail to connect, because the driver did not advertise
support for GMII for ports with internal PHY.
It should be noted that the aforementioned regression is not because the
blamed commit was incorrect: on the contrary, the blamed commit is
correcting the previous behaviour whereby unspecified phy-mode would
cause the internal interface mode to be PHY_INTERFACE_MODE_NA. The
rtl8365mb driver only worked by accident before because it _did_
advertise support for PHY_INTERFACE_MODE_NA, despite NA being reserved
for internal use by phylink. With one mistake fixed, the other was
exposed.
Commit a5dba0f207e5 ("net: dsa: rtl8365mb: add GMII as user port mode")
then introduced implicit support for GMII mode on ports with internal
PHY to allow a PHY connection for device trees where the phy-mode is not
explicitly set to "internal". At this point everything was working OK
again.
Subsequently, commit 6ff6064605e9 ("net: dsa: realtek: convert to
phylink_generic_validate()") broke this behaviour again by discarding
the usage of rtl8365mb_phy_mode_supported() - where this GMII support
was indicated - while switching to the new .phylink_get_caps API.
With the new API, rtl8365mb_phy_mode_supported() is no longer needed.
Remove it altogether and add back the GMII capability - this time to
rtl8365mb_phylink_get_caps() - so that the above default behaviour works
for ports with internal PHY again.
Fixes: 6ff6064605e9 ("net: dsa: realtek: convert to phylink_generic_validate()")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20220607184624.417641-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 47e96930d6e6106d5252e85b868d3c7e29296de0 ]
Commit ede359d8843a ("net: dsa: mv88e6xxx: Link in pcs_get_state() if AN
is bypassed") added the ability to link if AN was bypassed, and added
filling of state->an_complete field, but set it to true if AN was
enabled in BMCR, not when AN was reported complete in BMSR.
This was done because for some reason, when I wanted to use BMSR value
to infer an_complete, I was looking at BMSR_ANEGCAPABLE bit (which was
always 1), instead of BMSR_ANEGCOMPLETE bit.
Use BMSR_ANEGCOMPLETE for filling state->an_complete.
Fixes: ede359d8843a ("net: dsa: mv88e6xxx: Link in pcs_get_state() if AN is bypassed")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0737e018a05e2aa352828c52bdeed3b02cff2930 ]
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node.
when breaking early from a for_each_available_child_of_node() loop,
we need to explicitly call of_node_put() on the gphy_fw_np.
Add missing of_node_put() to avoid refcount leak.
Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220605072335.11257-1-linmq006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 02ded5a173619b11728b8bf75a3fd995a2c1ff28 ]
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
mv88e6xxx_mdio_register() pass the device node to of_mdiobus_register().
We don't need the device node after it.
Add missing of_node_put() to avoid refcount leak.
Fixes: a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0a3ad7d323686fbaae8688326cc5ea0d185c6fca ]
Since kconfig 'select' does not follow dependency chains, if symbol KSA
selects KSB, then KSA should also depend on the same symbols that KSB
depends on, in order to prevent Kconfig warnings and possible build
errors.
Change NET_DSA_SMSC_LAN9303_I2C and NET_DSA_SMSC_LAN9303_MDIO so that
they are limited to VLAN_8021Q if the latter is enabled. This prevents
the Kconfig warning:
WARNING: unmet direct dependencies detected for NET_DSA_SMSC_LAN9303
Depends on [m]: NETDEVICES [=y] && NET_DSA [=y] && (VLAN_8021Q [=m] || VLAN_8021Q [=m]=n)
Selected by [y]:
- NET_DSA_SMSC_LAN9303_I2C [=y] && NETDEVICES [=y] && NET_DSA [=y] && I2C [=y]
Fixes: 430065e26719 ("net: dsa: lan9303: add VLAN IDs to master device")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Juergen Borleis <jbe@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Mans Rullgard <mans@mansr.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6cfc03b602200c5cbbd8d906fd905547814e83df ]
Restore original way to handle mdio read error by returning 0xffff.
This was wrongly changed when the internal_mdio_read was introduced,
now that both legacy and internal use the same function, make sure that
they behave the same way.
Fixes: ce062a0adbfe ("net: dsa: qca8k: fix kernel panic with legacy mdio mapping")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 66f862563ed68717dfd84e808ca12705ed275ced ]
When using an external PHY connected using RGMII to mt7531 port 5, the
PHY can be used to used support 1000BASE-X connections. Moreover, if
1000BASE-T is supported, then we should allow 1000BASE-X as well, since
which are supported is a property of the PHY.
Therefore, it makes no sense to exclude this from the linkmodes when
1000BASE-T is supported.
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
After commit 2d1f90f9ba83 ("net: dsa/bcm_sf2: fix incorrect usage of
state->link") the interface suspend path would call our mac_link_down()
call back which would forcibly set the link down, thus preventing
Wake-on-LAN packets from reaching our management port.
Fix this by looking at whether the port is enabled for Wake-on-LAN and
not clearing the link status in that case to let packets go through.
Fixes: 2d1f90f9ba83 ("net: dsa/bcm_sf2: fix incorrect usage of state->link")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220512021731.2494261-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the blamed commit, VCAP filters can appear on more than one list.
If their action is "trap", they are chained on ocelot->traps via
filter->trap_list. This is in addition to their normal placement on the
VCAP block->rules list head.
Therefore, when we free a VCAP filter, we must remove it from all lists
it is a member of, including ocelot->traps.
There are at least 2 bugs which are direct consequences of this design
decision.
First is the incorrect usage of list_empty(), meant to denote whether
"filter" is chained into ocelot->traps via filter->trap_list.
This does not do the correct thing, because list_empty() checks whether
"head->next == head", but in our case, head->next == head->prev == NULL.
So we dereference NULL pointers and die when we call list_del().
Second is the fact that not all places that should remove the filter
from ocelot->traps do so. One example is ocelot_vcap_block_remove_filter(),
which is where we have the main kfree(filter). By keeping freed filters
in ocelot->traps we end up in a use-after-free in
felix_update_trapping_destinations().
Attempting to fix all the buggy patterns is a whack-a-mole game which
makes the driver unmaintainable. Actually this is what the previous
patch version attempted to do:
https://patchwork.kernel.org/project/netdevbpf/patch/20220503115728.834457-3-vladimir.oltean@nxp.com/
but it introduced another set of bugs, because there are other places in
which create VCAP filters, not just ocelot_vcap_filter_create():
- ocelot_trap_add()
- felix_tag_8021q_vlan_add_rx()
- felix_tag_8021q_vlan_add_tx()
Relying on the convention that all those code paths must call
INIT_LIST_HEAD(&filter->trap_list) is not going to scale.
So let's do what should have been done in the first place and keep a
bool in struct ocelot_vcap_filter which denotes whether we are looking
at a trapping rule or not. Iterating now happens over the main VCAP IS2
block->rules. The advantage is that we no longer risk having stale
references to a freed filter, since it is only present in that list.
Fixes: e42bd4ed09aa ("net: mscc: ocelot: keep traps in a list")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert B53 to use phylink_pcs for the serdes rather than hooking it
into the MAC-layer callbacks.
Fixes: 81c1681cbb9f ("net: dsa: b53: mark as non-legacy")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add of_node_put() if of_get_phy_mode() fails in mt7530_setup()
Fixes: 0c65b2b90d13 ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220428095317.538829-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch limits the sniffing to only one port during the mirror add.
And during the mirror_del it checks for all the ports using the sniff,
if and only if no other ports are referring, sniffing is disabled.
The code is updated based on the review comments of LAN937x port mirror
patch.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210422094257.1641396-8-prasanna.vengateshan@microchip.com/
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20220428070709.7094-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 4b5923249b8fa4 ("net: dsa: lantiq_gswip: Configure all remaining
GSWIP_MII_CFG bits") added all known bits in the GSWIP_MII_CFGp
register. It helped bring this register into a well-defined state so the
driver has to rely less on the bootloader to do things right.
Unfortunately it also sets the GSWIP_MII_CFG_RMII_CLK bit without any
possibility to configure it. Upon further testing it turns out that all
boards which are supported by the GSWIP driver in OpenWrt which use an
RMII PHY have a dedicated oscillator on the board which provides the
50MHz RMII reference clock.
Don't set the GSWIP_MII_CFG_RMII_CLK bit (but keep the code which always
clears it) to fix support for the Fritz!Box 7362 SL in OpenWrt. This is
a board with two Atheros AR8030 RMII PHYs. With the "RMII clock" bit set
the MAC also generates the RMII reference clock whose signal then
conflicts with the signal from the oscillator on the board. This results
in a constant cycle of the PHY detecting link up/down (and as a result
of that: the two ports using the AR8030 PHYs are not working).
At the time of writing this patch there's no known board where the MAC
(GSWIP) has to generate the RMII reference clock. If needed this can be
implemented in future by providing a device-tree flag so the
GSWIP_MII_CFG_RMII_CLK bit can be toggled per port.
Fixes: 4b5923249b8fa4 ("net: dsa: lantiq_gswip: Configure all remaining GSWIP_MII_CFG bits")
Tested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20220425152027.2220750-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The other port_hidden functions rely on the port_read/port_write
functions to access the hidden control port. These functions apply the
offset for port_base_addr where applicable. Update port_hidden_wait to
use the port_wait_bit so that port_base_addr offsets are accounted for
when waiting for the busy bit to change.
Without the offset the port_hidden_wait function would timeout on
devices that have a non-zero port_base_addr (e.g. MV88E6141), however
devices that have a zero port_base_addr would operate correctly (e.g.
MV88E6390).
Fixes: 609070133aff ("net: dsa: mv88e6xxx: update code operating on hidden registers")
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220425070454.348584-1-nathan@nathanrossi.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There is no need to add new compatible strings for each new supported
chip version. The compatible string is used only to select the subdriver
(rtl8365mb.c or rtl8366rb.c). Once in the subdriver, it will detect the
chip model by itself, ignoring which compatible string was used.
Link: https://lore.kernel.org/netdev/20220414014055.m4wbmr7tdz6hsa3m@bang-olufsen.dk/
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20220418233558.13541-2-luizluca@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the device tree has 2 CPU ports defined, a single one is active
(has any dp->cpu_dp pointers point to it). Yet the second one is still a
CPU port, and DSA still calls ->change_tag_protocol on it.
On the NXP LS1028A, the CPU ports are ports 4 and 5. Port 4 is the
active CPU port and port 5 is inactive.
After the following commands:
# Initial setting
cat /sys/class/net/eno2/dsa/tagging
ocelot
echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
echo ocelot > /sys/class/net/eno2/dsa/tagging
traffic is now broken, because the driver has moved the NPI port from
port 4 to port 5, unbeknown to DSA.
The problem can be avoided by detecting that the second CPU port is
unused, and not doing anything for it. Further rework will be needed
when proper support for multiple CPU ports is added.
Treat this as a bug and prepare current kernels to work in single-CPU
mode with multiple-CPU DT blobs.
Fixes: adb3dccf090b ("net: dsa: felix: convert to the new .change_tag_protocol DSA API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220412172209.2531865-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This switch is not even supported, but if someone were to actually put
this compatible string "realtek,rtl8366s" in their device tree, they
would be greeted with a kernel panic because the probe function would
dereference NULL. So let's just remove it.
Link: https://lore.kernel.org/all/CACRpkdYdKZs0WExXc3=0yPNOwP+oOV60HRz7SRoGjZvYHaT=1g@mail.gmail.com/
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel test robot reported a build failure:
or1k-linux-ld: drivers/net/dsa/realtek/realtek-smi.o:(.rodata+0x16c): undefined reference to `rtl8366rb_variant'
... with the following build configuration:
CONFIG_NET_DSA_REALTEK=y
CONFIG_NET_DSA_REALTEK_SMI=y
CONFIG_NET_DSA_REALTEK_RTL8365MB=y
CONFIG_NET_DSA_REALTEK_RTL8366RB=m
The problem here is that the realtek-smi interface driver gets built-in,
while the rtl8366rb switch subdriver gets built as a module, hence the
symbol rtl8366rb_variant is not reachable when defining the OF device
table in the interface driver.
The Kconfig dependencies don't help in this scenario because they just
say that the subdriver(s) depend on at least one interface driver. In
fact, the subdrivers don't depend on the interface drivers at all, and
can even be built even in their absence. Somewhat strangely, the
interface drivers can also be built in the absence of any subdriver,
BUT, if a subdriver IS enabled, then it must be reachable according to
the linkage of the interface driver: effectively what the IS_REACHABLE()
macro achieves. If it is not reachable, the above kind of linker error
will be observed.
Rather than papering over the above build error by simply using
IS_REACHABLE(), we can do a little better and admit that it is actually
the interface drivers that have a dependency on the subdrivers. So this
patch does exactly that. Specifically, we ensure that:
1. The interface drivers' Kconfig symbols must have a value no greater
than the value of any subdriver Kconfig symbols.
2. The subdrivers should by default enable both interface drivers, since
most users probably want at least one of them; those interface
drivers can be explicitly disabled however.
What this doesn't do is prevent a user from building only a subdriver,
without any interface driver. To that end, add an additional line of
help in the menu to guide users in the right direction.
Link: https://lore.kernel.org/all/202204110757.XIafvVnj-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Fixes: aac94001067d ("net: dsa: realtek: add new mdio interface for drivers")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DSA master might not have been probed yet in which case the probe of
the felix switch fails with -EPROBE_DEFER:
[ 4.435305] mscc_felix 0000:00:00.5: Failed to register DSA switch: -517
It is not an error. Use dev_err_probe() to demote this particular error
to a debug message.
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220408101521.281886-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As the possible failure of the allocation, kzalloc() may return NULL
pointer.
Therefore, it should be better to check the 'sgi' in order to prevent
the dereference of NULL pointer.
Fixes: 23ae3a7877718 ("net: dsa: felix: add stream gate settings for psfp").
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220329090800.130106-1-zhengyongjun3@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The bug is here:
return rule;
The list iterator value 'rule' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty or no element
is found.
To fix the bug, return 'rule' when found, otherwise return NULL.
Fixes: ae7a5aff783c7 ("net: dsa: bcm_sf2: Keep copy of inserted rules")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220328032431.22538-1-xiam0nd.tong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The kernel test robot reported build warnings with a randconfig that
built realtek-{smi,mdio} without CONFIG_OF set. Since both interface
drivers are using OF and will not probe without, add the corresponding
dependency to Kconfig.
Link: https://lore.kernel.org/all/202203231233.Xx73Y40o-lkp@intel.com/
Link: https://lore.kernel.org/all/202203231439.ycl0jg50-lkp@intel.com/
Fixes: aac94001067d ("net: dsa: realtek: add new mdio interface for drivers")
Fixes: 765c39a4fafe ("net: dsa: realtek: convert subdrivers into modules")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://lore.kernel.org/r/20220323124225.91763-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some chips using the split VTU/STU design will not accept VTU entries
who's SID points to an invalid STU entry. Therefore, mark all those
chips with either the mv88e6352_g1_stu_* or mv88e6390_g1_stu_* ops as
appropriate.
Notably, chips for the Opal Plus (6085/6097) era seem to use a
different implementation than those from Agate (6352) and onwards,
even though their external interface is the same. The former happily
accepts VTU entries referencing invalid STU entries, while the latter
does not.
This fixes an issue where the driver would fail to probe switch trees
that contained chips of the Agate/Topaz generation which did not
declare STU support, as loaded VTU entries would be read back as
invalid.
Fixes: 49c98c1dc7d9 ("net: dsa: mv88e6xxx: Disentangle STU from VTU")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220319110345.555270-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Felix switch has 6 ports, 2 of which are internal.
Due to some misunderstanding, my initial suggestion for
vsc9959_port_modes[]:
https://patchwork.kernel.org/project/netdevbpf/patch/20220129220221.2823127-10-colin.foster@in-advantage.com/#24718277
got translated by Colin into a 5-port array, leading to an all-zero port
mode mask for port 5.
Fixes: acf242fc739e ("net: dsa: felix: remove prevalidate_phy_mode interface")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220318195812.276276-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the same way that we check for STU support in the MST state
callback, we should also verify it before trying to change a VLANs
MSTI membership.
Fixes: acaf4d2e36b3 ("net: dsa: mv88e6xxx: MST Offloading")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simply having a physical STU table in the device doesn't do us any
good if there's no implementation of the relevant ops to access that
table. So ensure that chips that claim STU support can also talk to
the hardware.
This fixes an issue where chips that had a their ->info->max_sid
set (due to their family membership), but no implementation (due to
their chip-specific ops struct) would fail to probe.
Fixes: 49c98c1dc7d9 ("net: dsa: mv88e6xxx: Disentangle STU from VTU")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Gain support for port mirroring using tc-matchall by forwarding the
calls to the ocelot switch library.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drivers might have error messages to propagate to user space, most
common being that they support a single mirror port.
Propagate the netlink extack so that they can inform user space in a
verbal way of their limitations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to erratum described in DS80000687C[1]: "Module 2: Link drops with
some EEE link partners.", we need to "Disable the EEE next page
exchange in EEE Global Register 2"
1 - https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ87xx-Errata-DS80000687C.pdf
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220316125529.1489045-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allocate a SID in the STU for each MSTID in use by a bridge and handle
the mapping of MSTIDs to VLANs using the SID field of each VTU entry.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Export the raw STU data in a devlink region so that it can be
inspected from userspace and compared to the current bridge
configuration.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In early LinkStreet silicon (e.g. 6095/6185), the per-VLAN STP states
were kept in the VTU - there was no concept of a SID. Later, the
information was split into two tables, where the VTU only tracked
memberships and deferred the STP state tracking to the STU via a
pointer (SID). This meant that a group of VLANs could share the same
STU entry. Most likely, this was done to align with MSTP (802.1Q-2018,
Clause 13), which is built on this principle.
While the VTU is still 4k lines on most devices, the STU is capped at
64 entries. This means that the current stategy, updating STU info
whenever a VTU entry is updated, can not easily support MSTP because:
- The maximum number of VIDs would also be capped at 64, as we would
have to allocate one SID for every VTU entry - even if many VLANs
would effectively share the same MST.
- MSTP updates would be unnecessarily slow as you would have to
iterate over all VLANs that share the same MST.
In order to support MSTP offloading in the future, manage the STU as a
separate entity from the VTU.
Only add support for newer hardware with separate VTU and
STU. VTU-only devices can also be supported, but essentially this
requires a software implementation of an STU (fanning out state
changed to all VLANs tied to the same MST).
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Follow the established programming model for this driver and provide
shims in the felix DSA driver which call the implementations from the
ocelot switch lib. The ocelot switchdev driver wasn't integrated with
dcbnl due to lack of hardware availability.
The switch doesn't have any fancy QoS classification enabled by default.
The provided getters will create a default-prio app table entry of 0,
and no dscp entry. However, the getters have been made to actually
retrieve the hardware configuration rather than static values, to be
future proof in case DSA will need this information from more call paths.
For default-prio, there is a single field per port, in ANA_PORT_QOS_CFG,
called QOS_DEFAULT_VAL.
DSCP classification is enabled per-port, again via ANA_PORT_QOS_CFG
(field QOS_DSCP_ENA), and individual DSCP values are configured as
trusted or not through register ANA_DSCP_CFG (replicated 64 times).
An untrusted DSCP value falls back to other QoS classification methods.
If trusted, the selected ANA_DSCP_CFG register also holds the QoS class
in the QOS_DSCP_VAL field.
The hardware also supports DSCP remapping (DSCP value X is translated to
DSCP value Y before the QoS class is determined based on the app table
entry for Y) and DSCP packet rewriting. The dcbnl framework, for being
so flexible in other useless areas, doesn't appear to support this.
So this functionality has been left out.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add spi_device_id tables to avoid logs like "SPI driver ksz9477-switch
has no spi_device_id".
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This enables non-standard MTUs on a per-port basis, with the overall
frame size set based on the CPU port.
When the MTU is not changed, this should have no effect.
Long packets crash the switch with MTUs of greater than 2526, so the
maximum is limited for now. Medium packets are sometimes dropped (e.g.
TCP over 2477, UDP over 2516-2519, ICMP over 2526), Hence an MTU value
of 2400 seems safe.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://lore.kernel.org/r/20220308230457.1599237-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
net/dsa/dsa2.c
commit afb3cc1a397d ("net: dsa: unlock the rtnl_mutex when dsa_master_setup() fails")
commit e83d56537859 ("net: dsa: replay master state events in dsa_tree_{setup,teardown}_master")
https://lore.kernel.org/all/20220307101436.7ae87da0@canb.auug.org.au/
drivers/net/ethernet/intel/ice/ice.h
commit 97b0129146b1 ("ice: Fix error with handling of bonding MTU")
commit 43113ff73453 ("ice: add TTY for GNSS module for E810T device")
https://lore.kernel.org/all/20220310112843.3233bcf1@canb.auug.org.au/
drivers/staging/gdm724x/gdm_lte.c
commit fc7f750dc9d1 ("staging: gdm724x: fix use after free in gdm_lte_rx()")
commit 4bcc4249b4cf ("staging: Use netif_rx().")
https://lore.kernel.org/all/20220308111043.1018a59d@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This chips supports two ways to configure max MTU size:
- by setting SW_LEGAL_PACKET_DISABLE bit: if this bit is 0 allowed packed size
will be between 64 and bytes 1518. If this bit is 1, it will accept
packets up to 2000 bytes.
- by setting SW_JUMBO_PACKET bit. If this bit is set, the chip will
ignore SW_LEGAL_PACKET_DISABLE value and use REG_SW_MTU__2 register to
configure MTU size.
Current driver has disabled SW_JUMBO_PACKET bit and activates
SW_LEGAL_PACKET_DISABLE. So the switch will pass all packets up to 2000 without
any way to configure it.
By providing port_change_mtu we are switch to SW_JUMBO_PACKET way and will
be able to configure MTU up to ~9000.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220308135857.1119028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Felix driver declares FDB isolation but puts all standalone ports in
VID 0. This is mostly problem-free as discussed with Alvin here:
https://patchwork.kernel.org/project/netdevbpf/cover/20220302191417.1288145-1-vladimir.oltean@nxp.com/#24763870
however there is one catch. DSA still thinks that FDB entries are
installed on the CPU port as many times as there are user ports, and
this is problematic when multiple user ports share the same MAC address.
Consider the default case where all user ports inherit their MAC address
from the DSA master, and then the user runs:
ip link set swp0 address 00:01:02:03:04:05
The above will make dsa_slave_set_mac_address() call
dsa_port_standalone_host_fdb_add() for 00:01:02:03:04:05 in port 0's
standalone database, and dsa_port_standalone_host_fdb_del() for the old
address of swp0, again in swp0's standalone database.
Both the ->port_fdb_add() and ->port_fdb_del() will be propagated down
to the felix driver, which will end up deleting the old MAC address from
the CPU port. But this is still in use by other user ports, so we end up
breaking unicast termination for them.
There isn't a problem in the fact that DSA keeps track of host
standalone addresses in the individual database of each user port: some
drivers like sja1105 need this. There also isn't a problem in the fact
that some drivers choose the same VID/FID for all standalone ports.
It is just that the deletion of these host addresses must be delayed
until they are known to not be in use any longer, and only the driver
has this knowledge. Since DSA keeps these addresses in &cpu_dp->fdbs and
&cpu_db->mdbs, it is just a matter of walking over those lists and see
whether the same MAC address is present on the CPU port in the port db
of another user port.
I have considered reusing the generic dsa_port_walk_fdbs() and
dsa_port_walk_mdbs() schemes for this, but locking makes it difficult.
In the ->port_fdb_add() method and co, &dp->addr_lists_lock is held, but
dsa_port_walk_fdbs() also acquires that lock. Also, even assuming that
we introduce an unlocked variant of the address iterator, we'd still
need some relatively complex data structures, and a void *ctx in the
dsa_fdb_walk_cb_t which we don't currently pass, such that drivers are
able to figure out, after iterating, whether the same MAC address is or
isn't present in the port db of another port.
All the above, plus the fact that I expect other drivers to follow the
same model as felix where all standalone ports use the same FID, made me
conclude that a generic method provided by DSA is necessary:
dsa_fdb_present_in_other_db() and the mdb equivalent. Felix calls this
from the ->port_fdb_del() handler for the CPU port, when the database
was classified to either a port db, or a LAG db.
For symmetry, we also call this from ->port_fdb_add(), because if the
address was installed once, then installing it a second time serves no
purpose: it's already in hardware in VID 0 and it affects all standalone
ports.
This change moves dsa_db_equal() from switch.c to dsa.c, since it now
has one more caller.
Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The two blamed commits were written/tested individually but not
together.
When put together, commit 90897569beb1 ("net: dsa: felix: start off with
flooding disabled on the CPU port"), which deletes a reinitialization of
PGID_UC/PGID_MC/PGID_BC, is no longer sufficient to ensure that these
port masks don't contain the CPU port module.
This is because commit b903a6bd2e19 ("net: dsa: felix: migrate flood
settings from NPI to tag_8021q CPU port") overwrites the hardware
default settings towards the CPU port module with the settings that used
to be present on the NPI port treated as a regular port. There, flooding
is enabled, so flooding would get enabled on the CPU port module too.
Adding conditional logic somewhere within felix_setup_tag_npi() to
configure either the default no-flood policy or the flood policy
inherited from the tag_8021q CPU port from a previous call to
dsa_port_manage_cpu_flood() is getting complicated. So just let the
migration logic do its thing during initial setup (which will
temporarily turn on flooding), then turn flooding off for the NPI port
after felix_set_tag_protocol() finishes. Here we are in felix_setup(),
so the DSA slave interfaces are not yet created, and this doesn't affect
traffic in any way.
Fixes: 90897569beb1 ("net: dsa: felix: start off with flooding disabled on the CPU port")
Fixes: b903a6bd2e19 ("net: dsa: felix: migrate flood settings from NPI to tag_8021q CPU port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We no longer need the workaround in the felix driver to avoid calling
dsa_port_walk_fdbs() when &dp->fdbs is an uninitialized list, because
that list is now initialized from all call paths of felix_set_tag_protocol().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Discussing one of the tests in mt753x_phylink_validate() with Landen
Chao confirms that the "||" should be "&&". Fix this.
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1nRCF0-00CiXD-7q@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The trailing tag is also supported by this family. The default is still
rtl8_4 but now the switch supports changing the tag to rtl8_4t.
Reintroduce the dropped cpu in struct rtl8365mb (removed by 6147631).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit
baebdf48c3600 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to an apparently incorrect conflict resolution on my part in commit
54c319846086 ("net: mscc: ocelot: enforce FDB isolation when
VLAN-unaware"), "ocelot->ports[port]->is_dsa_8021q_cpu = false" was
supposed to be replaced by "ocelot_port_unset_dsa_8021q_cpu(ocelot, port)"
which does the same thing, and more. But now we have both, so the direct
assignment is redundant. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
