| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Since commit 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done
before HW reset") the following error is seen on a imx8mn board with
a 88E6320 switch:
mv88e6085 30be0000.ethernet-1:00: Timeout waiting for EEPROM done
This board does not have an EEPROM attached to the switch though.
This problem is well explained by Andrew Lunn:
"If there is an EEPROM, and the EEPROM contains a lot of data, it could
be that when we perform a hardware reset towards the end of probe, it
interrupts an I2C bus transaction, leaving the I2C bus in a bad state,
and future reads of the EEPROM do not work.
The work around for this was to poll the EEInt status and wait for it
to go true before performing the hardware reset.
However, we have discovered that for some boards which do not have an
EEPROM, EEInt never indicates complete. As a result,
mv88e6xxx_g1_wait_eeprom_done() spins for a second and then prints a
warning.
We probably need a different solution than calling
mv88e6xxx_g1_wait_eeprom_done(). The datasheet for 6352 documents the
EEPROM Command register:
bit 15 is:
EEPROM Unit Busy. This bit must be set to a one to start an EEPROM
operation (see EEOp below). Only one EEPROM operation can be
executing at one time so this bit must be zero before setting it to
a one. When the requested EEPROM operation completes this bit will
automatically be cleared to a zero. The transition of this bit from
a one to a zero can be used to generate an interrupt (the EEInt in
Global 1, offset 0x00).
and more interesting is bit 11:
Register Loader Running. This bit is set to one whenever the
register loader is busy executing instructions contained in the
EEPROM."
Change to using mv88e6xxx_g2_eeprom_wait() to fix the timeout error
when the EEPROM chip is not present.
Fixes: 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The force watchdog event bit is not cleared during SW reset in the
mv88e6393x switch. This is a different behavior compared to mv886390 which
clears the force WD event bit as advertised. This causes a force WD event
to be handled over and over again as the SW reset following the event never
clears the force WD event bit.
Explicitly clear the watchdog event register to 0 in irq_action when
handling an event to prevent the switch from sending continuous interrupts.
Marvell aren't aware of any other stuck bits apart from the force WD
bit.
Fixes: de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family"
Signed-off-by: Gustav Ekelund <gustaek@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The global2 SMI MDIO bus driver can perform both C22 and C45
transfers. Create separate functions for each and register the C45
versions using the new API calls where appropriate. Update the SERDES
code to make use of these new accessors.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
p0_mode set to one of the supported serial mode should not prevent
configuring the external SMI interface in
mv88e6xxx_g2_scratch_gpio_set_smi. The current masking of the p0_mode
only checks the first 2 bits. This results in switches supporting
serial mode cannot setup external SMI on certain serial modes
(Ex: 1000BASE-X and SGMII).
Extend the mask of the p0_mode to include the reduced modes and
serial modes as allowed modes for the external SMI interface.
Signed-off-by: Marcus Carlberg <marcus.carlberg@axis.com>
Link: https://lore.kernel.org/r/20220824093706.19049-1-marcus.carlberg@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Read the hardware configuration to determine which port is attached
to the serdes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Export the raw PVT data in a devlink region so that it can be
inspected from userspace and compared to the current bridge
configuration.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because ADRR is not a thing.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Marvell 88E6393X device is a single-chip integration of a 11-port
Ethernet switch with eight integrated Gigabit Ethernet (GbE)
transceivers and three 10-Gigabit interfaces.
This patch adds functionalities specific to mv88e6393x family (88E6393X,
88E6193X and 88E6191X).
The main differences between previous devices and this one are:
- port 0 can be a SERDES port
- all SERDESes are one-lane, eg. no XAUI nor RXAUI
- on the other hand the SERDESes can do USXGMII, 10GBASER and 5GBASER
(on 6191X only one SERDES is capable of more than 1g; USXGMII is not
yet supported with this change)
- Port Policy CTL register is changed to Port Policy MGMT CTL register,
via which several more registers can be accessed indirectly
- egress monitor port is configured differently
- ingress monitor/CPU/mirror ports are configured differently and can be
configured per port (ie. each port can have different ingress monitor
port, for example)
- port speed AltBit works differently than previously
- PHY registers can be also accessed via MDIO address 0x18 and 0x19
(on previous devices they could be accessed only via Global 2 offsets
0x18 and 0x19, which means two indirections; this feature is not yet
leveraged with thiis commit)
Co-developed-by: Ashkan Boldaji <ashkan.boldaji@digi.com>
Signed-off-by: Ashkan Boldaji <ashkan.boldaji@digi.com>
Signed-off-by: Pavana Sharma <pavana.sharma@digi.com>
Co-developed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Early generations of the mv88e6xxx did not have the global 2
registers. In order to keep the driver slim, it was decided to make
the code for these registers optional. Over time, more generations of
switches have been added, always supporting global 2 and adding more
and more registers. No effort has been made to keep these additional
registers also optional to slim the driver down when used for older
generations. Optional global 2 now just gives additional development
and maintenance burden for no real gain.
Make global 2 support always compiled in.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20210127003210.663173-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support for Global 2 registers is build-time optional. In the case
where it was not enabled the build would fail as no "dummy"
implementation of these functions was available.
Fixes: 57e661aae6a8 ("net: dsa: mv88e6xxx: Link aggregation support")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support offloading of LAGs to hardware. LAGs may be attached to a
bridge in which case VLANs, multicast groups, etc. are also offloaded
as usual.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mv88e6xxx_g2_atu_stats_get() takes two parameters. Make the stub
function also take two, otherwise we get compile errors.
Fixes: c5f299d59261 ("net: dsa: mv88e6xxx: global1_atu: Add helper for get next")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When retrieving the ATU statistics, and ATU get next has to be
performed to trigger the ATU to collect the statistics. Export a
helper from global1_atu to perform this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helpers to set/get the ATU statistics register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have proper Wait Bit and Wait Mask routines, remove the
unused mv88e6xxx_wait routine and its Global 1 and Global 2 variants.
The indirect tables such as the Device Mapping Table or Priority
Override Table make use of an Update bit to distinguish reading (0)
from writing (1) operations. After a write operation occurs, the bit
self clears right away so there's no need to wait on it. Thus keep
things simple and remove the mv88e6xxx_update helper as well.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many portions of the driver need to wait until a given bit is set
or cleared. Some busses even have a specific implementation for this
operation. In preparation for such variant, implement a generic Wait
Bit routine that can be used by the driver core functions.
This allows us to get rid of the custom implementations we may find
in the driver. Note that for the EEPROM bits, BUSY and RUNNING bits
are independent, thus it is more efficient to wait independently for
each bit instead of waiting for their mask.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MV88E6352_G2_WDOG_CTL_* bits almost, but not quite, describe the
watchdog control register on the mv88e6250. Among those actually
referenced in the code, only QC_ENABLE differs (bit 6 rather than bit
5).
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The MV88E6165 PTP registers are all in AVB bank F, unlike newer
generations which spread them over AVB bank E and F. Implement AVB ops
for the MV88E6165 which hides this difference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The remaining values written to the Switch Management Register in the
mv88e6xxx_g2_setup function are specific to 88E6352 and older, and are
the default values anyway.
Thus remove completely this function. The mv88e6xxx driver no more
contains setup code to access arbitrary Global 2 registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the Device Mapping setup out of the specific Global 2 code,
into the top level device setup function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the trunking setup out of Global 2 specific setup into the top
level mv88e6xxx_setup function.
Note that the 88E6390 family calls this LAG instead of Trunk and
supports 32 possible ID routing vectors, with LAG ID bit 4 being placed
in Global 2 register 0x1D...
We don't need Trunk (or LAG) IDs for the moment, thus keep it simple.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When registering an MDIO bus, it is possible to pass an array of
interrupts, one per address on the bus. phylib will then associate the
interrupt to the PHY device, if no other interrupt is provided.
Some of the global2 interrupts are PHY interrupts. Place them into the
MDIO bus structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Declaring a static function in a header leads to a warning every
time that header gets included without the function being used:
In file included from drivers/net/dsa/mv88e6xxx/chip.c:42:
drivers/net/dsa/mv88e6xxx/ptp.h:92:13: error: 'mv88e6xxx_hwtstamp_work' defined but not used [-Werror=unused-function]
static long mv88e6xxx_hwtstamp_work(struct ptp_clock_info *ptp)
In file included from drivers/net/dsa/mv88e6xxx/chip.c:38:
drivers/net/dsa/mv88e6xxx/global2.h:355:12: error: 'mv88e6xxx_g2_wait' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_wait(struct mv88e6xxx_chip *chip, int reg, u16 mask)
^~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:350:12: error: 'mv88e6xxx_g2_update' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_update(struct mv88e6xxx_chip *chip, int reg, u16 update)
^~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:345:12: error: 'mv88e6xxx_g2_write' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_write(struct mv88e6xxx_chip *chip, int reg, u16 val)
^~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:340:12: error: 'mv88e6xxx_g2_read' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_read(struct mv88e6xxx_chip *chip, int reg, u16 *val)
This marks all such functions in dsa inline to make sure we don't warn
about them.
Fixes: c6fe0ad2c349 ("net: dsa: mv88e6xxx: add rx/tx timestamping support")
Fixes: 0d632c3d6fe3 ("net: dsa: mv88e6xxx: add accessors for PTP/TAI registers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MV88E6352 and later switches support GPIO control through the "Scratch
& Misc" global2 register. Two of the pins controlled this way on the
mv88e6390 family are the external MDIO pins. They can either by used
as part of the MII interface for port 0, GPIOs, or MDIO. Add a
function to configure them for MDIO, if possible, and call it when
registering the external MDIO bus.
Suggested-by: Russell King <rmk@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MV88E6352 and later switches support GPIO control through the "Scratch
& Misc" global2 register. (Older switches do too, though with a slightly
different register interface. Only the 6352-style is implemented here.)
Add a new file, global2_scratch.c, for operations in the Scratch & Misc
space. Additionally, add a GPIO operations structure to present an
abstract view over GPIO manipulation.
Reverse Christmas tree and unsigned has been replaced with unsigned
int by Andrew Lunn.
Signed-off-by: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements support for accessing the Precision Time Protocol
and Time Application Interface registers via the AVB register interface
in the Global 2 register.
The register interface differs slightly between different models; older
models use a 3-bit operations field, while newer models use a 2-bit
field. The operations values and the special "global port" values are
different between the two. This is a similar split to the differences
in the "Ingress Rate" register between models, so, like in that case,
we call the two variants "6352" and "6390" and create an ops structure
to abstract between the two.
checkpatch fixups by Andrew Lunn
Signed-off-by: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let the mv88e6xxx_g2_* register accessor functions be accessible
outside of global2.c.
Signed-off-by: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly to global1_addr, add a global2_addr member in the info
structure to describe the presence of the Global 2 Registers.
This allows us to get rid of the MV88E6XXX_FLAG_GLOBAL2 flag.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a pot_clear operation to clear the Priority Override Table and wrap
its call into a mv88e6xxx_pot_setup helper.
This allows us to get rid of the MV88E6XXX_FLAG_G2_POT flag.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 88E6185 family only has one 16-bit register to mark the 16 802.1D
reserved multicast addresses in the range of 01:80:C2:00:00:0x as MGMT.
The 88E6352 family also has one 16-bit register to mark the 16 GARP
reserved multicast addresses in the range of 01:80:C2:00:00:2x as MGMT.
Split the existing mv88e6095 prefixed mgmt_rsvd2cpu operation into two
distinct mv88e6185 and mv88e6352 prefixed operations, and wrap its call
into a mv88e6xxx_rsvd2cpu_setup helper.
This allows us to also get rid of the MV88E6XXX_CAP_G2_MGMT_EN_* flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly to g1_irqs, add a g2_irqs member to the info structure to
indicates the presence of the Global 2 Interrupt Source and Mask
registers.
At the same time, provide helpers and document the registers since they
differ a bit between 88E6352 and 88E6390 families.
This allows us to get rid of the MV88E6XXX_FLAG_G2_INT flag.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prefix and document the remaining Global 2 registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Marvell 88E6352 family has a Global 2 register dedicated to the
watchdog setup. But the 88E6390 turned it into an indirect table.
Prefix and document that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prefix and document the Global 2 Switch MAC registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prefix and document the Global 2 EEPROM registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prefix and document the Global 2 Cross-chip Port VLAN registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prefix and document the Global 2 MGMT registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prefix and document the Global 2 Device Mapping macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prefix and document the Global 2 Trunk registers macros. At the same
time, fix the hask -> hash typo and use the mv88e6xxx_port_mask helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell chips with an SMI PHY access in Global 2 registers handle both
Clause 22 and Clause 45 of IEEE 802.3.
The 88E6390 family has addition bits to target the internal or external
PHYs connected to the device, and a Setup function in addition to the
default (register) Access function.
Prefix the SMI PHY Command and Data registers macros, implement clear
helpers for Clause 22 and 44 Access functions, rename variable to match
the SMI and switch vocabulary (device and register addresses for Clause
22 and port and device class for Clause 45.)
Finally do not use complex macros but simple 16-bit mask to document the
registers organization.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Marvell chips have an Ingress Rate Limit unit. But the command
values slightly differs between models: 88E6352 use 3-bit for operations
while 88E6390 use different 2-bit operations.
This commit kills the IRL flags in favor of a new operation implementing
the "Init all resources to the initial state" operation.
This fixes the operation of 88E6390 family where 0x1000 means Read the
selected resource 0, register 0 on port 16, instead of init all.
A mv88e6xxx_irl_setup helper is added to wrap the operation call.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just some simple overlapping changes in marvell PHY driver
and the DSA core code.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the GLOBAL2_* macros where they belong, in the related global2.h
header.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6xxx.h is meant to contains the chip structures and data.
Rename it to chip.h, as for other source/header pairs of the driver.
At the same time, ensure that relative header inclusions are separated
by a newline and sorted alphabetically.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'static' was not enough, the helpers must be 'static inline'
net/dsa/mv88e6xxx/global2.h:123:12: error: 'mv88e6xxx_g2_misc_4_bit_port' defined but not used [-Werror=unused-function]
net/dsa/mv88e6xxx/global2.h:117:12: error: 'mv88e6xxx_g2_pvt_write' defined but not used [-Werror=unused-function]
Fixes: c21fbe29f858 ("net: dsa: mv88e6xxx: Add missing static to stub functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stub functions in header files need to be static, or we can have
multiple definitions errors.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 6335e9f2446b ("net: dsa: mv88e6xxx: mv88e6390X SERDES support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Cross-chip Port Based VLAN Table (PVT) is currently initialized with
all ones, allowing any external ports to egress frames on local ports.
This commit implements the PVT access functions and programs the PVT
with all ones for the local switch ports only, instead of using the Init
operation. The current behavior is unchanged for the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Cross-chip Port Based VLAN Table (PVT) supports two indexing modes,
one using 5-bit for device and 4-bit for port, the other using 4-bit for
device and 5-bit for port, configured via the Global 2 Misc register.
Only 4 bits for the source port are needed when interconnecting 88E6xxx
switch devices since they all support less than 16 physical ports. The
full 5 bits are needed when interconnecting a device with 98DXxxx switch
devices since they support more than 16 physical ports.
Add a mv88e6xxx_pvt_setup helper to set the 4-bit port PVT mode, which
will be extended later to also initialize the PVT content.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
