| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- Dynamic partition support
- Fix deadlock in sm_ftl
- Various refcount fixes in maps, partitions and parser code
- Integer overflow fixes in mtdchar
- Support for Sercomm partitions
NAND driver changes:
- Clockrate fix for arasan
- Add ATO25D1GA support
- Double free fix for meson driver
- Fix probe/remove methods in cafe NAND
- Support unprotected spare data pages in qcom_nandc
SPI NOR core changes:
- move SECT_4K_PMC flag out of the core as it's a vendor specific
flag
- s/addr_width/addr_nbytes/g: address width means the number of IO
lines used for the address, whereas in the code it is used as the
number of address bytes.
- do not change nor->addr_nbytes at SFDP parsing time. At the SFDP
parsing time we should not change members of struct spi_nor, but
instead fill members of struct spi_nor_flash_parameters which could
later on be used by the callers.
- track flash's internal address mode so that we can use 4B opcodes
together with opcodes that don't have a 4B opcode correspondent.
SPI NOR manufacturer drivers changes:
- esmt: Rename "f25l32qa" flash name to "f25l32qa-2s".
- micron-st: Skip FSR reading if SPI controller does not support it
to allow flashes that support FSR to work even when attached to
such SPI controllers.
- spansion: Add s25hl-t/s25hs-t IDs and fixups"
* tag 'mtd/for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (53 commits)
mtd: core: check partition before dereference
mtd: spi-nor: fix spi_nor_spimem_setup_op() call in spi_nor_erase_{sector,chip}()
mtd: spi-nor: spansion: Add s25hl-t/s25hs-t IDs and fixups
mtd: spi-nor: spansion: Add local function to discover page size
mtd: spi-nor: core: Track flash's internal address mode
mtd: spi-nor: core: Return error code from set_4byte_addr_mode()
mtd: spi-nor: Do not change nor->addr_nbytes at SFDP parsing time
mtd: spi-nor: core: Shrink the storage size of the flash_info's addr_nbytes
mtd: spi-nor: s/addr_width/addr_nbytes
mtd: spi-nor: esmt: Use correct name of f25l32qa
mtd: spi-nor: micron-st: Skip FSR reading if SPI controller does not support it
MAINTAINERS: Use my kernel.org email
mtd: rawnand: arasan: Fix clock rate in NV-DDR
mtd: rawnand: arasan: Update NAND bus clock instead of system clock
mtd: core: introduce of support for dynamic partitions
dt-bindings: mtd: partitions: add additional example for qcom,smem-part
dt-bindings: mtd: partitions: support label/name only partition
mtd: spi-nor: move SECT_4K_PMC special handling
mtd: dataflash: Add SPI ID table
mtd: hyperbus: rpc-if: Fix RPM imbalance in probe error path
...
|
|
Pull block updates from Jens Axboe:
- Improve the type checking of request flags (Bart)
- Ensure queue mapping for a single queues always picks the right queue
(Bart)
- Sanitize the io priority handling (Jan)
- rq-qos race fix (Jinke)
- Reserved tags handling improvements (John)
- Separate memory alignment from file/disk offset aligment for O_DIRECT
(Keith)
- Add new ublk driver, userspace block driver using io_uring for
communication with the userspace backend (Ming)
- Use try_cmpxchg() to cleanup the code in various spots (Uros)
- Finally remove bdevname() (Christoph)
- Clean up the zoned device handling (Christoph)
- Clean up independent access range support (Christoph)
- Clean up and improve block sysfs handling (Christoph)
- Clean up and improve teardown of block devices.
This turns the usual two step process into something that is simpler
to implement and handle in block drivers (Christoph)
- Clean up chunk size handling (Christoph)
- Misc cleanups and fixes (Bart, Bo, Dan, GuoYong, Jason, Keith, Liu,
Ming, Sebastian, Yang, Ying)
* tag 'for-5.20/block-2022-07-29' of git://git.kernel.dk/linux-block: (178 commits)
ublk_drv: fix double shift bug
ublk_drv: make sure that correct flags(features) returned to userspace
ublk_drv: fix error handling of ublk_add_dev
ublk_drv: fix lockdep warning
block: remove __blk_get_queue
block: call blk_mq_exit_queue from disk_release for never added disks
blk-mq: fix error handling in __blk_mq_alloc_disk
ublk: defer disk allocation
ublk: rewrite ublk_ctrl_get_queue_affinity to not rely on hctx->cpumask
ublk: fold __ublk_create_dev into ublk_ctrl_add_dev
ublk: cleanup ublk_ctrl_uring_cmd
ublk: simplify ublk_ch_open and ublk_ch_release
ublk: remove the empty open and release block device operations
ublk: remove UBLK_IO_F_PREFLUSH
ublk: add a MAINTAINERS entry
block: don't allow the same type rq_qos add more than once
mmc: fix disk/queue leak in case of adding disk failure
ublk_drv: fix an IS_ERR() vs NULL check
ublk: remove UBLK_IO_F_INTEGRITY
ublk_drv: remove unneeded semicolon
...
|
|
syzbot is reporting NULL pointer dereference at mtd_check_of_node() [1],
for mtdram test device (CONFIG_MTD_MTDRAM) is not partition.
Link: https://syzkaller.appspot.com/bug?extid=fe013f55a2814a9e8cfd [1]
Reported-by: syzbot <syzbot+fe013f55a2814a9e8cfd@syzkaller.appspotmail.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: ad9b10d1eaada169 ("mtd: core: introduce of support for dynamic partitions")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
CC: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
SPI NOR core changes:
- move SECT_4K_PMC flag out of the core as it's a vendor specific flag
- s/addr_width/addr_nbytes: address width means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes.
- do not change nor->addr_nbytes at SFDP parsing time. At the SFDP parsing
time we should not change members of struct spi_nor, but instead fill
members of struct spi_nor_flash_parameters which could later on be used
by the callers.
- track flash's internal address mode so that we can use 4B opcodes
together with opcodes that don't have a 4B opcode correspondent.
SPI NOR manufacturer drivers changes:
- esmt: Rename "f25l32qa" flash name to "f25l32qa-2s".
- micron-st: Skip FSR reading if SPI controller does not support it to
allow flashes that support FSR to work even when attached to such SPI
controllers.
- spansion: Add s25hl-t/s25hs-t IDs and fixups.
|
|
|
|
spi_nor_erase_{sector,chip}()
For erase operations, reg_proto must be used as indicated in
struct spi_nor description in spi-nor.h.
This issue was found when DT property spi-tx-bus-width is set to 4.
In this case the spi_mem_op->addr.buswidth is set to 4 for erase command
which is not correct.
Tested on stm32mp157c-ev1 board with mx66l51235f spi-nor.
Fixes: 0e30f47232ab ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
[ta: use nor->reg_proto in spi_nor_controller_ops_erase()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220629133013.3382393-1-patrice.chotard@foss.st.com
|
|
The S25HL-T/S25HS-T family is the Infineon SEMPER Flash with Quad SPI.
These Infineon chips support volatile version of configuration registers
and it is recommended to update volatile registers in the field application
due to a risk of the non-volatile registers corruption by power interrupt.
Add support for volatile QE bit.
For the single-die package parts (512Mb and 1Gb), only bottom 4KB and
uniform sector sizes are supported. This is due to missing or incorrect
entries in SMPT. Fixup for other sector sizes configurations will be
followed up as needed.
Tested on Xilinx Zynq-7000 FPGA board.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-8-tudor.ambarus@microchip.com
|
|
The page size check in s28hs512t fixup can be used for s25hs/hl-t as well.
Move that to a newly created local function.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-7-tudor.ambarus@microchip.com
|
|
We need to track the flash's internal address mode as there are flashes
that can operate with 4B opcodes but unfortunately do not have a 4B opcode
correspondent for all the 3B opcodes. Such an example is the Infineon
Semper chips which provide 4B opcodes for read/program/erase but do not
provide 4B opcodes for Read/Write Any Register. These registers are
indexed by address and require the internal address mode of the flash
before Read/Write Any Register opcodes are issued.
4B opcodes are preferred over changing the flash's address mode to 4byte,
as set_4byte_addr_mode could be done in a non-volatile way and could break
the boot sequence. Thus we need to track the flash's internal address mode
so that we can use 4B opcodes together with opcodes that don't have a 4B
opcode correspondent. Track flash's internal address mode.
addr_mode_nbytes is discovered when parsing BFPT. For the
BFPT_DWORD1_ADDRESS_BYTES_3_OR_4 case, one could introduce a method that
queries the flash's internal address mode at run-time (works for Winbond).
If a run-time querying can not be accomplished or if SFDP is not defined
at all, but the address mode is volatile and resets to a default known
value at boot, one can change the default addr_mode_nbytes value of 3 by
introducing a flash_info flag. If the address mode can not be queried,
discovered and it is configured via a non-volatile register, we may
introduce a dt property, but it will harm the generic approach of the
jedec,spi-nor compatible. All this complexity is not needed now, so let it
for future development.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-6-tudor.ambarus@microchip.com
|
|
The prams->set_4byte_addr_mode returns error code but is not handled
in spi_nor_init(). Handle the return code from set_4byte_addr_mode().
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-5-tudor.ambarus@microchip.com
|
|
At the SFDP parsing time we should not change members of struct spi_nor,
but instead fill members of struct spi_nor_flash_parameters which could
later on be used by callers. The caller will then decide if SFDP params
should be used and more importantly when they should be used. Clean the
code flow and don't initialize nor->addr_nbytes at SFDP parsing time.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-4-tudor.ambarus@microchip.com
|
|
The maximum number of address bytes in SPI NOR is 4. Shrink the storage
size of the flash_info's addr_nbytes.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-3-tudor.ambarus@microchip.com
|
|
Address width was an unfortunate name, as it means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes. s/addr_width/addr_nbytes throughout the entire SPI NOR
framework.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-2-tudor.ambarus@microchip.com
|
|
The flash ID of F25L32QA is 0x8c4016, whereas that of F25L32QA(2S) is
0x8c4116. F25L32QA(2S) is the newer version of F25L32QA and its BPn bits
are non-volatile, unlike its older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210723141232.15659-1-mans0n@gorani.run
Datasheet: https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F25L32QA.pdf
Datasheet: https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F25L32QA_1(2S).pdf
|
|
The Intel SPI controller does not support low level operations, like
reading the flag status register (FSR). It only exposes a set of high
level operations for software to use. For this reason check the return
value of micron_st_nor_read_fsr() and if the operation was not
supported, use the status register value only. This allows the chip to
work even when attached to Intel SPI controller (there are such systems
out there).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220506105158.43613-1-mika.westerberg@linux.intel.com
|
|
06781a5026350 Fixes the calculation of the DEVICE_BUSY_TIMEOUT register
value from busy_timeout_cycles. busy_timeout_cycles is calculated wrong
though: It is calculated based on the maximum page read time, but the
timeout is also used for page write and block erase operations which
require orders of magnitude bigger timeouts.
Fix this by calculating busy_timeout_cycles from the maximum of
tBERS_max and tPROG_max.
This is for now the easiest and most obvious way to fix the driver.
There's room for improvements though: The NAND_OP_WAITRDY_INSTR tells us
the desired timeout for the current operation, so we could program the
timeout dynamically for each operation instead of setting a fixed
timeout. Also we could wire up the interrupt handler to actually detect
and forward timeouts occurred when waiting for the chip being ready.
As a sidenote I verified that the change in 06781a5026350 is really
correct. I wired up the interrupt handler in my tree and measured the
time between starting the operation and the timeout interrupt handler
coming in. The time increases 41us with each step in the timeout
register which corresponds to 4096 clock cycles with the 99MHz clock
that I have.
Fixes: 06781a5026350 ("mtd: rawnand: gpmi: Fix setting busy timeout setting")
Fixes: b1206122069aa ("mtd: rawniand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
According to the Arasan NAND controller spec, the flash clock rate for SDR
must be <= 100 MHz, while for NV-DDR it must be the same as the rate of the
CLK line for the mode. The driver previously always set 100 MHz for NV-DDR,
which would result in incorrect behavior for NV-DDR modes 0-4.
The appropriate clock rate can be calculated from the NV-DDR timing
parameters as 1/tCK, or for rates measured in picoseconds,
10^12 / nand_nvddr_timings->tCK_min.
Fixes: 197b88fecc50 ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable@vger.kernel.org # 5.8+
Signed-off-by: Olga Kitaina <okitain@gmail.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220628154824.12222-3-amit.kumar-mahapatra@xilinx.com
|
|
In current implementation the Arasan NAND driver is updating the
system clock(i.e., anand->clk) in accordance to the timing modes
(i.e., SDR or NVDDR). But as per the Arasan NAND controller spec the
flash clock or the NAND bus clock(i.e., nfc->bus_clk), need to be
updated instead. This patch keeps the system clock unchanged and updates
the NAND bus clock as per the timing modes.
Fixes: 197b88fecc50 ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable@vger.kernel.org # 5.8+
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220628154824.12222-2-amit.kumar-mahapatra@xilinx.com
|
|
We have many parser that register mtd partitions at runtime. One example
is the cmdlinepart or the smem-part parser where the compatible is defined
in the dts and the partitions gets detected and registered by the
parser. This is problematic for the NVMEM subsystem that requires an OF
node to detect NVMEM cells.
To fix this problem, introduce an additional logic that will try to
assign an OF node to the MTD if declared.
On MTD addition, it will be checked if the MTD has an OF node and if
not declared will check if a partition with the same label / node name is
declared in DTS. If an exact match is found, the partition dynamically
allocated by the parser will have a connected OF node.
The NVMEM subsystem will detect the OF node and register any NVMEM cells
declared statically in the DTS.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220622010628.30414-4-ansuelsmth@gmail.com
|
|
blk_cleanup_disk is nothing but a trivial wrapper for put_disk now,
so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20220619060552.1850436-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The SECT_4K_PMC flag will set a device specific opcode for the 4k sector
erase. Instead of handling it in the core, we can move it to a
late_init(). In that late init, loop over all erase types, look for the
4k size and replace the opcode.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220418112650.2791459-1-michael@walle.cc
|
|
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e2166 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220620152313.708768-1-broonie@kernel.org
|
|
If rpcif_hw_init() fails, Runtime PM is left enabled.
Fixes: b04cc0d912eb80d3 ("memory: renesas-rpc-if: Add support for RZ/G2L")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/f3070e1af480cb252ae183d479a593dbbf947685.1655457790.git.geert+renesas@glider.be
|
|
there is an unexpected word 'is' in the comments that need to be dropped
file: drivers/mtd/nand/raw/sm_common.c
line: 55
/* NOTE: This layout is is not compatabable with SmartMedia, */
changed to:
/* NOTE: This layout is not compatabable with SmartMedia, */
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220622160511.11679-1-jiangjian@cdjrlc.com
|
|
IPQ8064 nand have special pages where a different layout scheme is used.
These special page are used by boot partition and on reading them
lots of warning are reported about wrong ECC data and if written to
results in broken data and not bootable device.
The layout scheme used by these special page consist in using 512 bytes
as the codeword size (even for the last codeword) while writing to CFG0
register. This forces the NAND controller to unprotect the 4 bytes of
spare data.
Since the kernel is unaware of this different layout for these special
page, it does try to protect the spare data too during read/write and
warn about CRC errors.
Add support for this by permitting the user to declare these special
pages in dts by declaring offset and size of the partition. The driver
internally will convert these value to nand pages.
On user read/write the page is checked and if it's a boot page the
correct layout is used.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220616001835.24393-3-ansuelsmth@gmail.com
|
|
Reorder structs in nandc driver to save holes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220616001835.24393-2-ansuelsmth@gmail.com
|
|
of_get_child_by_name() will increase the refcount of 'ofpart_node',
so add of_node_put() after using it to avoid refcount leak.
Fixes: 9b78ef0c7997 ("mtd: parsers: add support for Sercomm partitions")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220617014008.851583-1-yangyingliang@huawei.com
|
|
The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as:
| Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY
| mode. This value is the number of GPMI_CLK cycles multiplied by 4096.
So instead of multiplying the value in cycles with 4096, we have to
divide it by that value. Use DIV_ROUND_UP to make sure we are on the
safe side, especially when the calculated value in cycles is smaller
than 4096 as typically the case.
This bug likely never triggered because any timeout != 0 usually will
do. In my case the busy timeout in cycles was originally calculated as
2408, which multiplied with 4096 is 0x968000. The lower 16 bits were
taken for the 16 bit wide register field, so the register value was
0x8000. With 2970bf5a32f0 ("mtd: rawnand: gpmi: fix controller timings
setting") however the value in cycles became 2384, which multiplied
with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an
intermediate timeout when reading from NAND.
Fixes: b1206122069aa ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220614083138.3455683-1-s.hauer@pengutronix.de
|
|
This reverts commit 3380557fc7e28d9bce7607e16d98f123d36da4ca.
It turned out this "4-byte" ID might have been an honest mistake.
Regrettably, the chip Andreas has might be a counterfeit or is
damaged in some other way and shouldn't have ended up in a router.
Andreas reported his chip is returning just four bytes:
"98 f1 80 15 00 00 00 00".
However, according to Kioxia/Toshiba's datasheet, there should
have been at least another byte that would have contained the
correct OOB size that Andreas needed.
Miquel and Andreas are both favoring reverting the patch over
further, possibly hacky modifications:
"[Reverting] is the safest option here. Apart from this device, we
do not know how many devices have these damaged/counterfeit chips.
If it is just a couple and only on Fritzboxes, as suggested in the
Github issue the patch could be carried through OpenWrt[...]"
Thanks to several users on the openwrt forum and github issue,
who stayed along for the ride:
- Peter-vdL for reporting the issue and testing patches.
- neg2led and Hannu Nyman who did all the
datasheet digging and debugging.
Cc: Andreas Boehler <dev@aboehler.at>
Suggested-by: Andreas Boehler <dev@aboehler.at>
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://github.com/openwrt/openwrt/issues/9962
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607185918.1048204-1-chunkeey@gmail.com
|
|
Instead of ending each if branch with the same check, do it once
unconditionally after the if block.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607152458.232847-5-u.kleine-koenig@pengutronix.de
|
|
Until mtd_device_unregister() returns the device is expected to be
operational. So only disable the clock after the mtd is unregistered.
Fixes: 1fefc8ecb834 ("mtd: st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607152458.232847-4-u.kleine-koenig@pengutronix.de
|
|
mtd_device_unregister() shouldn't fail. Wail loudly if it does anyhow.
This matches how other drivers (e.g. nand/raw/nandsim.c) use
mtd_device_unregister().
By returning 0 in the platform remove callback a generic error message
by the device core is suppressed, nothing else changes.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607152458.232847-3-u.kleine-koenig@pengutronix.de
|
|
For all but one error path clk_disable_unprepare() is already there. Add
it to the one location where it's missing.
Fixes: 481815a6193b ("mtd: st_spi_fsm: Handle clk_prepare_enable/clk_disable_unprepare.")
Fixes: 69d5af8d016c ("mtd: st_spi_fsm: Obtain and use EMI clock")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607152458.232847-2-u.kleine-koenig@pengutronix.de
|
|
The Linux device core doesn't intend remove callbacks to fail. If an
error code is returned the device is removed anyhow. So wail loudly if
the atmel specific remove callback fails and return 0 anyhow to suppress
the generic (and little helpful) error message by the device core.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607062503.211345-1-u.kleine-koenig@pengutronix.de
|
|
The remove callback is only called after probe completed successfully.
In this case platform_set_drvdata() was called with a non-NULL argument
and so info is never NULL.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-15-u.kleine-koenig@pengutronix.de
|
|
If mtd_device_unregister() fails (which it doesn't when used correctly),
the resources bound by the nand chip should be freed anyhow as returning
an error value doesn't prevent the device getting unbound.
Instead use WARN_ON on the return value similar to how other drivers do
it.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-14-u.kleine-koenig@pengutronix.de
|
|
The driver core cares for unsetting platform data (see
device_unbind_cleanup()) on remove.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-13-u.kleine-koenig@pengutronix.de
|
|
If mtd_device_unregister() fails (which it doesn't when used correctly),
the resources bound by the nand chip should be freed anyhow as returning
an error value doesn't prevent the device getting unbound.
Instead use WARN_ON on the return value similar to how other drivers do
it. Then meson_nfc_nand_chip_cleanup() returns 0 unconditionally and can
be changed to return void which allows further simplification in the
remove callback.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-12-u.kleine-koenig@pengutronix.de
|
|
If mtd_device_unregister() fails (which it doesn't when used correctly),
the resources bound by the nand chip should be freed anyhow as returning
an error value doesn't prevent the device getting unbound.
Instead use WARN_ON on the return value similar to how other drivers do
it.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-11-u.kleine-koenig@pengutronix.de
|
|
Returning an error value in a platform remove callback results in an error
message being emitted by the platform core, but otherwise it doesn't make
a difference. After the WARN splat this generic error message doesn't add
any value, so return 0 unconditionally
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-10-u.kleine-koenig@pengutronix.de
|
|
The remove callback is only called after probe completed successfully.
In this case platform_set_drvdata() was called with a non-NULL argument
and so dev is never NULL.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-8-u.kleine-koenig@pengutronix.de
|
|
If mtd_device_unregister() fails (which it doesn't when used correctly),
the resources bound by the nand chip should be freed anyhow as returning
an error value doesn't prevent the device getting unbound.
Instead use WARN_ON on the return value similar to how other drivers do
it.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-7-u.kleine-koenig@pengutronix.de
|
|
mtd_device_unregister() shouldn't fail. Wail loudly if it does anyhow.
This matches how other drivers (e.g. nand/raw/nandsim.c) use
mtd_device_unregister().
By returning 0 in the platform remove callback a generic error message
by the device core is suppressed, nothing else changes.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-6-u.kleine-koenig@pengutronix.de
|
|
mtd_device_unregister() shouldn't fail. Wail loudly if it does anyhow.
This matches how other drivers (e.g. nand/raw/nandsim.c) use
mtd_device_unregister().
By returning 0 in the platform remove callback a generic error message
by the device core is suppressed, nothing else changes.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-4-u.kleine-koenig@pengutronix.de
|
|
The only thing that could theoretically fail in that function is
mtd_device_unregister(). However it's not supposed to fail and when
used correctly it doesn't. So wail loudly if it does anyhow.
This matches how other drivers (e.g. nand/raw/nandsim.c) use
mtd_device_unregister().
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-2-u.kleine-koenig@pengutronix.de
|
|
mtdchar_write_ioctl() calls kmalloc() with the 'size' argument set to
the smaller of two values: the write request's data/OOB length provided
by user space and the erase block size of the MTD device. If the latter
is large, kmalloc() may not be able to serve such allocation requests.
Use kvmalloc() instead. Correspondingly, replace kfree() calls with
kvfree() calls.
Suggested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220516070601.11428-3-kernel@kempniu.pl
|
|
Commit 6420ac0af95d ("mtdchar: prevent unbounded allocation in MEMWRITE
ioctl") added a safety check to mtdchar_write_ioctl() which attempts to
ensure that the write request sent by user space does not extend beyond
the MTD device's size. However, that check contains an addition of two
struct mtd_write_req fields, 'start' and 'len', both of which are u64
variables. The result of that addition can overflow, allowing the
safety check to be bypassed.
The arguably simplest fix - changing the data types of the relevant
struct mtd_write_req fields - is not feasible as it would break user
space.
Fix by making mtdchar_write_ioctl() truncate the value provided by user
space in the 'len' field of struct mtd_write_req, so that only the lower
32 bits of that field are used, preventing the overflow.
While the 'ooblen' field of struct mtd_write_req is not currently used
in any similarly flawed safety check, also truncate it to 32 bits, for
consistency with the 'len' field and with other MTD routines handling
OOB data.
Update include/uapi/mtd/mtd-abi.h accordingly.
Suggested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220516070601.11428-2-kernel@kempniu.pl
|
|
of_find_node_by_path() returns a node pointer with refcount incremented,
we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: bb17230c61a6 ("mtd: parsers: ofpart: support BCM4908 fixed partitions")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220605070726.5979-1-linmq006@gmail.com
|
|
This adds an MTD partition parser for the Sercomm partition table that
is used in some Beeline, Netgear and Sercomm routers.
The Sercomm partition map table contains real partition offsets, which
may differ from device to device depending on the number and location of
bad blocks on NAND.
Original patch (proposed by NOGUCHI Hiroshi):
Link: https://github.com/openwrt/openwrt/pull/1318#issuecomment-420607394
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220529110714.189732-1-csharper2005@gmail.com
|
|
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 237960880960 ("mtd: partitions: redboot: seek fis-index-block in the right node")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220526110652.64849-1-linmq006@gmail.com
|
