| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
spi_nor_erase_{sector,chip}()
For erase operations, reg_proto must be used as indicated in
struct spi_nor description in spi-nor.h.
This issue was found when DT property spi-tx-bus-width is set to 4.
In this case the spi_mem_op->addr.buswidth is set to 4 for erase command
which is not correct.
Tested on stm32mp157c-ev1 board with mx66l51235f spi-nor.
Fixes: 0e30f47232ab ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
[ta: use nor->reg_proto in spi_nor_controller_ops_erase()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220629133013.3382393-1-patrice.chotard@foss.st.com
|
|
The S25HL-T/S25HS-T family is the Infineon SEMPER Flash with Quad SPI.
These Infineon chips support volatile version of configuration registers
and it is recommended to update volatile registers in the field application
due to a risk of the non-volatile registers corruption by power interrupt.
Add support for volatile QE bit.
For the single-die package parts (512Mb and 1Gb), only bottom 4KB and
uniform sector sizes are supported. This is due to missing or incorrect
entries in SMPT. Fixup for other sector sizes configurations will be
followed up as needed.
Tested on Xilinx Zynq-7000 FPGA board.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-8-tudor.ambarus@microchip.com
|
|
The page size check in s28hs512t fixup can be used for s25hs/hl-t as well.
Move that to a newly created local function.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-7-tudor.ambarus@microchip.com
|
|
We need to track the flash's internal address mode as there are flashes
that can operate with 4B opcodes but unfortunately do not have a 4B opcode
correspondent for all the 3B opcodes. Such an example is the Infineon
Semper chips which provide 4B opcodes for read/program/erase but do not
provide 4B opcodes for Read/Write Any Register. These registers are
indexed by address and require the internal address mode of the flash
before Read/Write Any Register opcodes are issued.
4B opcodes are preferred over changing the flash's address mode to 4byte,
as set_4byte_addr_mode could be done in a non-volatile way and could break
the boot sequence. Thus we need to track the flash's internal address mode
so that we can use 4B opcodes together with opcodes that don't have a 4B
opcode correspondent. Track flash's internal address mode.
addr_mode_nbytes is discovered when parsing BFPT. For the
BFPT_DWORD1_ADDRESS_BYTES_3_OR_4 case, one could introduce a method that
queries the flash's internal address mode at run-time (works for Winbond).
If a run-time querying can not be accomplished or if SFDP is not defined
at all, but the address mode is volatile and resets to a default known
value at boot, one can change the default addr_mode_nbytes value of 3 by
introducing a flash_info flag. If the address mode can not be queried,
discovered and it is configured via a non-volatile register, we may
introduce a dt property, but it will harm the generic approach of the
jedec,spi-nor compatible. All this complexity is not needed now, so let it
for future development.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-6-tudor.ambarus@microchip.com
|
|
The prams->set_4byte_addr_mode returns error code but is not handled
in spi_nor_init(). Handle the return code from set_4byte_addr_mode().
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220725092505.446315-5-tudor.ambarus@microchip.com
|
|
At the SFDP parsing time we should not change members of struct spi_nor,
but instead fill members of struct spi_nor_flash_parameters which could
later on be used by callers. The caller will then decide if SFDP params
should be used and more importantly when they should be used. Clean the
code flow and don't initialize nor->addr_nbytes at SFDP parsing time.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-4-tudor.ambarus@microchip.com
|
|
The maximum number of address bytes in SPI NOR is 4. Shrink the storage
size of the flash_info's addr_nbytes.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-3-tudor.ambarus@microchip.com
|
|
Address width was an unfortunate name, as it means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes. s/addr_width/addr_nbytes throughout the entire SPI NOR
framework.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220725092505.446315-2-tudor.ambarus@microchip.com
|
|
The flash ID of F25L32QA is 0x8c4016, whereas that of F25L32QA(2S) is
0x8c4116. F25L32QA(2S) is the newer version of F25L32QA and its BPn bits
are non-volatile, unlike its older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210723141232.15659-1-mans0n@gorani.run
Datasheet: https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F25L32QA.pdf
Datasheet: https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F25L32QA_1(2S).pdf
|
|
The Intel SPI controller does not support low level operations, like
reading the flag status register (FSR). It only exposes a set of high
level operations for software to use. For this reason check the return
value of micron_st_nor_read_fsr() and if the operation was not
supported, use the status register value only. This allows the chip to
work even when attached to Intel SPI controller (there are such systems
out there).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220506105158.43613-1-mika.westerberg@linux.intel.com
|
|
The SECT_4K_PMC flag will set a device specific opcode for the 4k sector
erase. Instead of handling it in the core, we can move it to a
late_init(). In that late init, loop over all erase types, look for the
4k size and replace the opcode.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220418112650.2791459-1-michael@walle.cc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This is quite a quiet release but some new drivers mean that the
diffstat is fairly large. The new drivers include the aspeed driver
which is migrated from MTD as part of the ongoing move of controllers
with specialised support for SPI flashes into the SPI subsystem.
- Support for devices which flip CPHA during recieve only transfers
(eg, if MOSI and MISO have inverted polarity).
- Overhaul of the i.MX driver, including the addition of PIO support
for better performance on small transfers.
- Migration of the Aspeed driver from MTD.
- Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
IPM and SFI"
* tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (84 commits)
spi: spi-au1550: replace ternary operator with min()
mtd: spi-nor: aspeed: set the decoding size to at least 2MB for AST2600
spi: aspeed: Calibrate read timings
spi: aspeed: Add support for the AST2400 SPI controller
spi: aspeed: Workaround AST2500 limitations
spi: aspeed: Adjust direct mapping to device size
spi: aspeed: Add support for direct mapping
spi: spi-mem: Convert Aspeed SMC driver to spi-mem
spi: Convert the Aspeed SMC controllers device tree binding
spi: spi-cadence: Update ISR status variable type to irqreturn_t
spi: Doc fix - Describe add_lock and dma_map_dev in spi_controller
spi: cadence-quadspi: Handle spi_unregister_master() in remove()
spi: stm32-qspi: Remove SR_BUSY bit check before sending command
spi: stm32-qspi: Always check SR_TCF flags in stm32_qspi_wait_cmd()
spi: stm32-qspi: Fix wait_cmd timeout in APM mode
spi: cadence-quadspi: remove unnecessary (void *) casts
spi: cadence-quadspi: Add missing blank line in cqspi_request_mmap_dma()
spi: spi-imx: mx51_ecspi_prepare_message(): skip writing MX51_ECSPI_CONFIG register if unchanged
spi: spi-imx: add PIO polling support
spi: spi-imx: replace struct spi_imx_data::bitbang by pointer to struct spi_controller
...
|
|
This SPI driver adds support for the Aspeed static memory controllers
of the AST2600, AST2500 and AST2400 SoCs using the spi-mem interface.
* AST2600 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. Only supports SPI type flash memory
. different segment register interface
. single, dual and quad mode.
* AST2600 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. different segment register interface
. single, dual and quad mode.
* AST2500 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the driver
. single, dual mode.
* AST2500 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. single, dual mode.
* AST2400 New Static Memory Controller (also referred as FMC)
. BMC firmware
. New register set
. 5 chip select pins (CE0 ∼ CE4)
. supports NOR flash, NAND flash and SPI flash memory.
. single, dual and quad mode.
Each controller has a memory range on which flash devices contents are
mapped. Each device is assigned a window that can be changed at bootime
with the Segment Address Registers.
Each SPI flash device can then be accessed in two modes: Command and
User. When in User mode, SPI transfers are initiated with accesses to
the memory segment of a device. When in Command mode, memory
operations on the memory segment of a device generate SPI commands
automatically using a Control Register for the settings.
This initial patch adds support for User mode. Command mode needs a little
more work to check that the memory window on the AHB bus fits the device
size. It will come later when support for direct mapping is added.
Single and dual mode RX transfers are supported. Other types than SPI
are not supported.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-4-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The intention was to print the JEDEC ID in the following format:
nn nn nn
In this case format specifier has to be "%*ph". Fix it.
Fixes: 0257be79fc4a ("mtd: spi-nor: expose internal parameters via debugfs")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220512112027.3771734-1-michael@walle.cc
|
|
This patch allows accessing the upper 16m on the A variant (EN25QH256A) of
the EN25QH256 that shares same JEDEC ID.
Without this patch, addr_with is detected to be '4' but the read_opcode is
a plain READ (supporting only 3 byte addresses).
Setting PARSE_SFDP is enough to detect the read_opcode READ_4B on the A
variant. READ_4B is not available on the no-A variant.
Both variants support 4-byte address mode (spi_nor_set_4byte_addr_mode)
but that is prone to breaking on unexpected reboots if the reset pin isn't
connected (broken-flash-reset).
The no-A variant supports a 'high bank latch mode' that affects read,
program, and erase commands - similar to the extended address register
(EAR).
The HBL bit is manipulated using the ENHBL (0x67) and EXHBL (0x98)
opcodes.
Should it become necessary to distinguish the two variants in the future,
the A variant sets the SNOR_HWCAPS_READ_1_1_4 SFDP param - the no-A
variant doesn't.
Tested with and without fast read on the A variant only.
Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220502233310.791565-2-leon@georgemail.eu
|
|
Add support for winbond W25Q512NW-IM chip.
Below are the tests done:
1. Verified flashing binary image on spi card using flashrom tool.
2. Verified OTP support, below are the test results:
localhost / # cat
/sys/bus/platform/devices/soc\@0/88dc000.spi/spi_master/spi16/
spi16.0/spi-nor/jedec_id
ef8020
localhost / # cat
/sys/bus/platform/devices/soc\@0/88dc000.spi/spi_master/spi16/
spi16.0/spi-nor/manufacturer
winbond
localhost / # cat
/sys/bus/platform/devices/soc\@0/88dc000.spi/spi_master/spi16/
spi16.0/spi-nor/partname
w25q512nwm
localhost / # hexdump
/sys/bus/platform/devices/soc\@0/88dc000.spi/spi_master/sp
i16/spi16.0/spi-nor/sfdp
0000000 4653 5044 0106 ff01 0600 1001 0080 ff00
0000010 0084 0201 00d0 ff00 ffff ffff ffff ffff
0000020 6800 6c65 6f6c 7720 726f 646c ffff ffff
0000030 ffff ffff ffff ffff ffff ffff ffff ffff
*
0000080 20e5 fffb ffff 1fff eb44 6b08 3b08 bb42
0000090 fffe ffff ffff 0000 ffff eb40 200c 520f
00000a0 d810 0000 0233 00a6 e781 d914 63e9 3376
00000b0 757a 757a bdf7 5cd5 f719 ff5d 70e9 a5f9
00000c0 ffff ffff ffff ffff ffff ffff ffff ffff
00000d0 0aff fff0 ff21 ffdc
00000d8
localhost / # md5sum
/sys/bus/platform/devices/soc\@0/88dc000.spi/spi_master/spi
16/spi16.0/spi-nor/sfdp
106d89d6c049110bc94c01517cb4ce24
/sys/bus/platform/devices/soc@0/88dc000.spi/
spi_master/spi16/spi16.0/spi-nor/sfdp
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/1651234239-32217-1-git-send-email-quic_c_sbhanu@quicinc.com
|
|
There is no way to gather all information to verify support for a new
flash chip. Also if you want to convert an existing flash chip to the
new SFDP parsing, there is not enough information to determine if the
flash will work like before. To ease this development, expose internal
parameters via the debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429102018.2361038-2-michael@walle.cc
|
|
The function will also be used by the debugfs module.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429102018.2361038-1-michael@walle.cc
|
|
The "Extended Address Register" is winbond specific. If the flash is
larger than 16MiB and is used in 3 byte address mode, it is used to set
the remaining address bits. Move the write_ear() function, the opcode
macros and the spimem op template into the winbond module and rename
them accordingly.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220429100153.2338501-1-michael@walle.cc
|
|
The rdsr dummy cycles are only used by the 8d-8d-8d mode. Mention that
in the documentation.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220418112837.2792242-1-michael@walle.cc
|
|
Writing volatile registers are instant according to Micron and do not
need any status polling. Remove status polling on volatile registers write.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-12-tudor.ambarus@microchip.com
|
|
Writing volatile registers are instant according to Cypress and do not
need any status polling. Remove status polling on volatile registers write.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-11-tudor.ambarus@microchip.com
|
|
Clean the op declaration and hide the details of each op. With this it
results a cleanner, easier to read code. No functional change expected.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Michael Walle <michael@walle.cc>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220420103427.47867-10-tudor.ambarus@microchip.com
|
|
Introduce template operation to remove code duplication.
Split spi_nor_cypress_octal_dtr_enable() in
spi_nor_cypress_octal_dtr_ena() spi_nor_cypress_octal_dtr_dis() as it no
longer made sense to try to keep everything alltogether: too many
"if (enable)" throughout the code, which made the code difficult to read.
Add debug messages in case spi_nor_read_id() fails.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-9-tudor.ambarus@microchip.com
|
|
Introduce template operation to remove code duplication.
Split spi_nor_micron_octal_dtr_enable() in spi_nor_micron_octal_dtr_en()
and spi_nor_micron_octal_dtr_dis() as it no longer made sense to try to
keep everything alltogether: too many "if (enable)" throughout the code,
which made the code difficult to follow. Add dev_dbg messages in case
spi_nor_read_id() fails.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-8-tudor.ambarus@microchip.com
|
|
There are manufacturers that use registers indexed by address. Some of
them support "read/write any register" opcodes. Provide core methods that
can be used by all manufacturers. SPI NOR controller ops are intentionally
not supported as we intend to move all the SPI NOR controller drivers
under the SPI subsystem.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-7-tudor.ambarus@microchip.com
|
|
Use spi_nor_read_id() core method to avoid duplication of code. Now the ID
is read on the full SPI_NOR_MAX_ID_LEN instead of
round_up(nor->info->id_len, 2), but it doesn't harm to read more ID bytes,
so the change comes with no secondary effects. dev_dbg messages in case
spi_nor_read_id() fails, will be added in a further patch after we split
the octal DTR enable/disable methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-6-tudor.ambarus@microchip.com
|
|
RDID is used in the core to auto detect the flash, but also by some
manufacturer drivers that contain flashes that support Octal DTR mode,
so that they can read the flash ID after the switch to Octal DTR was made
to test if the switch was successful. Introduce a core method for RDID op
to avoid code duplication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-5-tudor.ambarus@microchip.com
|
|
In case spi_nor_match_name() returned NULL, the auto detection was
issued twice. There's no reason to try to detect the same chip twice,
do the auto detection only once.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-4-tudor.ambarus@microchip.com
|
|
Similar to spi_nor_match_name() extend the search of flash_info through
all the manufacturers, this time doing the match by ID. There's no reason
to limit the search per manufacturer yet, do it globally, search the flash
in all the parts of all manufacturers in a single method.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-3-tudor.ambarus@microchip.com
|
|
The method is matching a flash_info entry by searching by name. Rename
the method for better clarity.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220420103427.47867-2-tudor.ambarus@microchip.com
|
|
Read back Status Register 1 to ensure that the written byte match the
received value and return -EIO if read back test failed.
Without this patch, spi_nor_write_16bit_sr_and_check() only check the
second half of the 16bit. It causes errors like spi_nor_sr_unlock()
return success incorrectly when spi_nor_write_16bit_sr_and_check()
doesn't write SR successfully.
Fixes: 39d1e3340c73 ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220126073227.3401275-1-chentsung@chromium.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"There has been a lot of activity in the MTD subsystem recently, with a
number of SPI-NOR cleanups as well as the introduction of ECC engines
that can be used by SPI controllers (hence a few SPI patches in here).
Core MTD changes:
- Replace the expert mode symbols with a single helper
- Fix misuses of of_match_ptr()
- Remove partid and partname debugfs files
- tests: Fix eraseblock read speed miscalculation for lower partition
sizes
- TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
- spear_smi: use GFP_KERNEL
- mchp48l640: Add SPI ID table
- mchp23k256: Add SPI ID table
- blkdevs: Avoid soft lockups with some mtd/spi devices
- aspeed-smc: Improve probe resilience
Hyperbus changes:
- HBMC_AM654 should depend on ARCH_K3
NAND core changes:
- ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
- Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
- Fix misuses of of_match_node()
- Rework of_get_nand_bus_width()
- Remove of_get_nand_on_flash_bbt() wrapper
- Protect access to rawnand devices while in suspend
- bindings: Document the wp-gpios property
Rax NAND controller driver changes:
- atmel: Fix refcount issue in atmel_nand_controller_init
- nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
- rockchip: Fix platform_get_irq.cocci warning
- stm32_fmc2: Add NAND Write Protect support
- pl353: Set the nand chip node as the flash node
- brcmnand: Fix sparse warnings in bcma_nand
- omap_elm: Remove redundant variable 'errors'
- gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
- brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
- Check for error irq
SPI-NAND core changes:
- Delay a little bit the dirmap creation
- Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
- macronix: Use random program load
SPI NOR core changes:
- Move vendor specific code out of the core into vendor drivers.
- Unify all function and object names in the vendor modules.
- Make setup() callback optional to improve readability.
- Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
- Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
- spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
- Dropped mtd/cortina,gemini-flash.txt
- Convert BCM47xx partitions to json-schema
- Vendor prefixes: Clarify Macronix prefix
- SPI NAND: Convert spi-nand description file to yaml
- Raw NAND chip: Create a NAND chip description
- Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
- Describe Macronix NAND ECC engine
- Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory"
* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
mtd: nand: ecc: mxic: Fix compile test issue
mtd: nand: mxic-ecc: make two read-only arrays static const
mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
mtd: core: Remove partid and partname debugfs files
dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
mtd: spi-nor: renumber flags
mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
mtd: spi-nor: spansion: rename vendor specific functions and defines
mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
mtd: spi-nor: move all spansion specifics into spansion.c
mtd: spi-nor: spansion: slightly rework control flow in late_init()
mtd: spi-nor: micron-st: rename vendor specific functions and defines
mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
mtd: spi-nor: move all micron-st specifics into micron-st.c
mtd: spi-nor: xilinx: correct the debug message
mtd: spi-nor: xilinx: rename vendor specific functions and defines
...
|
|
SPI NOR core changes:
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Even if SPI_NOR_NO_ERASE was set, one could still send erase opcodes
to the flash. It is not recommended to send unsupported opcodes to
flashes. Fix the logic and do not set mtd->_erase when SPI_NOR_NO_ERASE
is specified. With this users will not be able to issue erase opcodes to
flashes and instead they will recive an -ENOTSUPP error.
Fixes: b199489d37b2 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220228163334.277730-1-tudor.ambarus@microchip.com
|
|
As we have deleted some flag, lets renumber them so there are no holes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-33-michael@walle.cc
|
|
Now that there is almost no special case code left in
spi_nor_sr_ready(), the return check looks odd. Move the function call
closer to the return code checking.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-32-michael@walle.cc
|
|
Drop the generic spi_nor prefix for all the spansion functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-31-michael@walle.cc
|
|
Now that all functions using that flag are local to the spansion module,
we can convert the flag to a manufacturer one.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-30-michael@walle.cc
|
|
The clear status register flags is only available on spansion flashes.
Move all the functions around that into the spanion module.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-29-michael@walle.cc
|
|
Don't return early when the flash is smaller than or equal to 16MiB. We
need to be able to register hooks for all sizes of flashes. This also has
the benefit that it increases the readability of the code because the
action, i.e. registering the fixups, is connected to the condition, i.e.
flashes larger than 16MiB.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-28-michael@walle.cc
|
|
Drop the generic spi_nor prefix for all the micron-st functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-27-michael@walle.cc
|
|
Now that all functions using that flag are local to the micron module,
we can convert the flag to a manufacturer one.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-26-michael@walle.cc
|
|
The flag status register is only available on micron flashes. Move all
the functions around that into the micron module.
This is almost a mechanical move except for the spi_nor_fsr_ready()
which now also checks the normal status register. Previously, this was
done in spi_nor_ready().
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-25-michael@walle.cc
|
|
XRDSR is a combination of xilinx and the RDSR opcode, but the register
is just the status register. Correct the debug message.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-24-michael@walle.cc
|
|
Drop the generic spi_nor prefix for all the xilinx functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-23-michael@walle.cc
|
|
Mechanically move all the xilinx functions to its own module.
Then register the new flash specific ready() function.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-22-michael@walle.cc
|
|
The _page_size marco parameter was missing parentheses around it. Add
them.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-21-michael@walle.cc
|
|
We will move vendor specific code into the vendor modules and thus we
will have to export these functions so they can be called.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-20-michael@walle.cc
|
|
Xilinx and Micron flashes have their own implementation of the
spi_nor_ready() function. At the moment, the core will figure out
which one to call according to some flags. Lay the foundation to
make it possible that a flash can register its own ready()
function.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-19-michael@walle.cc
|
