| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Some eMMCs from Micron have been reported to need ~800 ms timeout, while
enabling the CACHE ctrl after running sudden power failure tests. The
needed timeout is greater than what the card specifies as its generic CMD6
timeout, through the EXT_CSD register, hence the problem.
Normally we would introduce a card quirk to extend the timeout for these
specific Micron cards. However, due to the rather complicated debug process
needed to find out the error, let's simply use a minimum timeout of 1600ms,
the double of what has been reported, for all cards when enabling CACHE
ctrl.
Reported-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In commit 5320226a0512 ("mmc: core: Disable HPI for certain Hynix eMMC
cards"), then intent was to prevent HPI from being used for some eMMC
cards, which didn't properly support it. However, that went too far, as
even BKOPS and CACHE ctrl became prevented. Let's restore those parts and
allow BKOPS and CACHE ctrl even if HPI isn't supported.
Fixes: 5320226a0512 ("mmc: core: Disable HPI for certain Hynix eMMC cards")
Cc: Pratibhasagar V <pratibha@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
During a re-initialization of the eMMC card, we may fail to re-enable HPI.
In these cases, that isn't properly reflected in the card->ext_csd.hpi_en
bit, as it keeps being set. This may cause following attempts to use HPI,
even if's not enabled. Let's fix this!
Fixes: eb0d8f135b67 ("mmc: core: support HPI send command")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
While booting with rootfs on MMC, the following warning is encountered
on OMAP4430:
omap-dma-engine 4a056000.dma-controller: DMA-API: mapping sg segment longer than device claims to support [len=69632] [max=65536]
This is because the DMA engine has a default maximum segment size of 64K
but HSMMC sets:
mmc->max_blk_size = 512; /* Block Length at max can be 1024 */
mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */
mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
mmc->max_seg_size = mmc->max_req_size;
which ends up telling the block layer that we support a maximum segment
size of 65535*512, which exceeds the advertised DMA engine capabilities.
Fix this by clamping the maximum segment size to the lower of the
maximum request size and of the DMA engine device used for either DMA
channel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some of the SDMMC pads auto calibration values parsed from
devicetree are assigned incorrectly. This patch fixes it.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Fixes: 51b77c8ea784 ("mmc: tegra: Program pad autocal offsets from dt")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
V4_MODE is Bit-15 of SDHCI_HOST_CONTROL2 register.
Need to perform word access to this register.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Fixes: b3f80b434f72 ("mmc: sdhci: Add sd host v4 mode")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We observed some premature timeouts on a virtualization platform, the log
is like this:
case 1:
[159525.255629] mmc1: Internal clock never stabilised.
[159525.255818] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[159525.256049] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00001002
...
[159525.257205] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03
From the clock control register dump, we are pretty sure the clock was
stablized.
case 2:
[ 914.550127] mmc1: Reset 0x2 never completed.
[ 914.550321] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 914.550608] mmc1: sdhci: Sys addr: 0x00000010 | Version: 0x00001002
After checking the sdhci code, we found the timeout check actually has a
little window that the CPU can be scheduled out and when it comes back,
the original time set or check is not valid.
Fixes: 5a436cc0af62 ("mmc: sdhci: Optimize delay loops")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Commit 7d33c3581536 ("mmc: sdhci-omap: Workaround for Errata i802")
disabled DCRC interrupts during tuning. This write to the interrupt
enable register gets overwritten in sdhci_prepare_data() and the
interrupt is not in fact disabled. Fix this by disabling the interrupt
in the host->ier variable.
Fixes: 7d33c3581536 ("mmc: sdhci-omap: Workaround for Errata i802")
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since v2.6.22 or so there has been reports [1] about OMAP MMC being
broken on OMAP15XX based hardware (OMAP5910 and OMAP310). The breakage
seems to have been caused by commit 46a6730e3ff9 ("mmc-omap: Fix
omap to use MMC_POWER_ON") that changed clock enabling to be done
on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX
the hardware doesn't seem to like it and the MMC just stops responding.
Fix by memorizing the power mode and do the init only when necessary.
Before the patch (on Palm TE):
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmci-omap mmci-omap.0: command timeout (CMD8)
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmcblk0: recovery failed!
print_req_error: I/O error, dev mmcblk0, sector 0
Buffer I/O error on dev mmcblk0, logical block 0, async page read
mmcblk0: unable to read partition table
After the patch:
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmcblk0: p1
The patch is based on a fix and analysis done by Ladislav Michl.
Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770)
and OMAP2420 (Nokia N810).
[1] https://marc.info/?t=123175197000003&r=1&w=2
Fixes: 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON")
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Reported-by: Andrzej Zaborowski <balrogg@gmail.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When sending out CMD23 in the blk preparation, the comment there
rightfully says:
* However, it is not sufficient to just send CMD23,
* and avoid the final CMD12, as on an error condition
* CMD12 (stop) needs to be sent anyway. This, coupled
* with Auto-CMD23 enhancements provided by some
* hosts, means that the complexity of dealing
* with this is best left to the host. If CMD23 is
* supported by card and host, we'll fill sbc in and let
* the host deal with handling it correctly.
Let's do this behaviour for RPMB as well, and not send CMD23
independently. Otherwise IP cores (like Renesas SDHI) may timeout
because of automatic CMD23/CMD12 handling.
Reported-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
GLK firmware can indicate that the tuning value will be restored after
runtime suspend, but not actually do that. Add a workaround that detects
such cases, and lets the driver do re-tuning instead.
Reported-by: Anisse Astier <anisse@astier.eu>
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Problem:
The card detect IRQ does not work with modern BIOS (that want
to use _DSD to provide the card detect GPIO to the driver).
Details:
The mmc core provides the mmc_gpiod_request_cd() API to let host drivers
request the gpio descriptor for the "card detect" pin.
This pin is specified in the ACPI for the SDHC device:
* Either as a resource using _CRS. This is a method used by legacy BIOS.
(The driver needs to tell which resource index).
* Or as a named property ("cd-gpios"/"cd-gpio") in _DSD (which internally
points to an entry in _CRS). This way, the driver can lookup using a
string. This is what modern BIOS prefer to use.
This API finally results in a call to the following code:
struct gpio_desc *acpi_find_gpio(..., const char *con_id,...)
{
...
/* Lookup gpio (using "<con_id>-gpio") in the _DSD */
...
if (!acpi_can_fallback_to_crs(adev, con_id))
return ERR_PTR(-ENOENT);
...
/* Falling back to _CRS is allowed, Lookup gpio in the _CRS */
...
}
Note that this means that if the ACPI has _DSD properties, the kernel
will never use _CRS for the lookup (Because acpi_can_fallback_to_crs()
will always be false for any device hat has _DSD entries).
The SDHCI driver is thus currently broken on a modern BIOS, even if
BIOS provides both _CRS (for index based lookup) and _DSD entries (for
string based lookup). Ironically, none of these will be used for the
lookup currently because:
* Since the con_id is NULL, acpi_find_gpio() does not find a matching
entry in DSDT. (The _DSDT entry has the property name = "cd-gpios")
* Because ACPI contains DSDT entries, thus acpi_can_fallback_to_crs()
returns false (because device properties have been populated from
_DSD), thus the _CRS is never used for the lookup.
Fix:
Try "cd" for lookup in the _DSD before falling back to using NULL so
as to try looking up in the _CRS.
I've tested this patch successfully with both Legacy BIOS (that
provide only _CRS method) as well as modern BIOS (that provide both
_CRS and _DSD). Also the use of "cd" appears to be fairly consistent
across other users of this API (other MMC host controller drivers).
Link: https://lkml.org/lkml/2018/9/25/1113
Signed-off-by: Rajat Jain <rajatja@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: f10e4bf6632b ("gpio: acpi: Even more tighten up ACPI GPIO lookups")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"The main updates in this cycle were:
- Lots of perf tooling changes too voluminous to list (big perf trace
and perf stat improvements, lots of libtraceevent reorganization,
etc.), so I'll list the authors and refer to the changelog for
details:
Benjamin Peterson, Jérémie Galarneau, Kim Phillips, Peter
Zijlstra, Ravi Bangoria, Sangwon Hong, Sean V Kelley, Steven
Rostedt, Thomas Gleixner, Ding Xiang, Eduardo Habkost, Thomas
Richter, Andi Kleen, Sanskriti Sharma, Adrian Hunter, Tzvetomir
Stoyanov, Arnaldo Carvalho de Melo, Jiri Olsa.
... with the bulk of the changes written by Jiri Olsa, Tzvetomir
Stoyanov and Arnaldo Carvalho de Melo.
- Continued intel_rdt work with a focus on playing well with perf
events. This also imported some non-perf RDT work due to
dependencies. (Reinette Chatre)
- Implement counter freezing for Arch Perfmon v4 (Skylake and newer).
This allows to speed up the PMI handler by avoiding unnecessary MSR
writes and make it more accurate. (Andi Kleen)
- kprobes cleanups and simplification (Masami Hiramatsu)
- Intel Goldmont PMU updates (Kan Liang)
- ... plus misc other fixes and updates"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (155 commits)
kprobes/x86: Use preempt_enable() in optimized_callback()
x86/intel_rdt: Prevent pseudo-locking from using stale pointers
kprobes, x86/ptrace.h: Make regs_get_kernel_stack_nth() not fault on bad stack
perf/x86/intel: Export mem events only if there's PEBS support
x86/cpu: Drop pointless static qualifier in punit_dev_state_show()
x86/intel_rdt: Fix initial allocation to consider CDP
x86/intel_rdt: CBM overlap should also check for overlap with CDP peer
x86/intel_rdt: Introduce utility to obtain CDP peer
tools lib traceevent, perf tools: Move struct tep_handler definition in a local header file
tools lib traceevent: Separate out tep_strerror() for strerror_r() issues
perf python: More portable way to make CFLAGS work with clang
perf python: Make clang_has_option() work on Python 3
perf tools: Free temporary 'sys' string in read_event_files()
perf tools: Avoid double free in read_event_file()
perf tools: Free 'printk' string in parse_ftrace_printk()
perf tools: Cleanup trace-event-info 'tdata' leak
perf strbuf: Match va_{add,copy} with va_end
perf test: S390 does not support watchpoints in test 22
perf auxtrace: Include missing asm/bitsperlong.h to get BITS_PER_LONG
tools include: Adopt linux/bits.h
...
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce a host helper function to share re-tuning progress
MMC host:
- sdhci: Add support for v4 host mode
- sdhci-of-arasan: Add Support for AM654 MMC and PHY
- sdhci-sprd: Add support for Spreadtrum's host controller
- sdhci-tegra: Add support for HS400 enhanced strobe
- sdhci-tegra: Enable UHS/HS200 modes for Tegra186/210
- sdhci-tegra: Add support for HS400 delay line calibration
- sdhci-tegra: Add support for pad calibration
- sdhci-of-dwcmshc: Address 128MB DMA boundary limitation
- sdhci-of-esdhc: Add support for tuning erratum A008171
- sdhci-iproc: Add ACPI support
- mediatek: Add support for MT8183
- mediatek: Improve the support for tuning
- mediatek: Add bus clock control for MT2712
- jz4740: Add support for the JZ4725B
- mmci: Add support for the stm32 sdmmc variant
- mmci: Add support for an optional reset control
- mmci: Add some new variant specific properties/callbacks
- mmci: Re-structure DMA code to prepare for new variants
- renesas_sdhi: Add support for r8a77470, r8a7744 and r8a774a1
- renesas_sdhi_internal_dmac: Whitelist r8a77970 and r8a774a1
- tmio/uniphier-sd: Add new UniPhier SD/eMMC controller driver
- tmio/renesas_sdhi: Deal properly with SCC detection during re-tune
- tmio/renesas_sdhi: Refactor/consolidate clock management
- omap_hsmmc: Drop cover detection and some unused platform data
- dw_mmc-exynos: Enable tuning for more speed modes
- sunxi: Clarify the new timing mode and enable it for the A64 controller
- various: Convert to slot GPIO descriptors"
* tag 'mmc-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (129 commits)
mmc: mediatek: drop too much code of tuning method
mmc: mediatek: add MT8183 MMC driver support
mmc: mediatek: tune CMD/DATA together
mmc: mediatek: fix cannot receive new request when msdc_cmd_is_ready fail
mmc: mediatek: fill the actual clock for mmc debugfs
mmc: dt-bindings: add support for MT8183 SoC
mmc: uniphier-sd: avoid using broken DMA RX channel
mmc: uniphier-sd: fix DMA disabling
mmc: tmio: simplify the DMA mode test
mmc: tmio: remove TMIO_MMC_HAVE_HIGH_REG flag
mmc: tmio: move MFD variant reset to a platform hook
mmc: renesas_sdhi: Add r8a77470 SDHI1 support
dt-bindings: mmc: renesas_sdhi: Add r8a77470 support
mmc: mmci: add stm32 sdmmc variant
dt-bindings: mmci: add stm32 sdmmc variant
mmc: mmci: add stm32 sdmmc registers
mmc: mmci: add clock divider for stm32 sdmmc
mmc: mmci: add optional reset property
dt-bindings: mmci: add optional reset property
mmc: mmci: add variant property to not read datacnt
...
|
|
Pull block layer updates from Jens Axboe:
"This is the main pull request for block changes for 4.20. This
contains:
- Series enabling runtime PM for blk-mq (Bart).
- Two pull requests from Christoph for NVMe, with items such as;
- Better AEN tracking
- Multipath improvements
- RDMA fixes
- Rework of FC for target removal
- Fixes for issues identified by static checkers
- Fabric cleanups, as prep for TCP transport
- Various cleanups and bug fixes
- Block merging cleanups (Christoph)
- Conversion of drivers to generic DMA mapping API (Christoph)
- Series fixing ref count issues with blkcg (Dennis)
- Series improving BFQ heuristics (Paolo, et al)
- Series improving heuristics for the Kyber IO scheduler (Omar)
- Removal of dangerous bio_rewind_iter() API (Ming)
- Apply single queue IPI redirection logic to blk-mq (Ming)
- Set of fixes and improvements for bcache (Coly et al)
- Series closing a hotplug race with sysfs group attributes (Hannes)
- Set of patches for lightnvm:
- pblk trace support (Hans)
- SPDX license header update (Javier)
- Tons of refactoring patches to cleanly abstract the 1.2 and 2.0
specs behind a common core interface. (Javier, Matias)
- Enable pblk to use a common interface to retrieve chunk metadata
(Matias)
- Bug fixes (Various)
- Set of fixes and updates to the blk IO latency target (Josef)
- blk-mq queue number updates fixes (Jianchao)
- Convert a bunch of drivers from the old legacy IO interface to
blk-mq. This will conclude with the removal of the legacy IO
interface itself in 4.21, with the rest of the drivers (me, Omar)
- Removal of the DAC960 driver. The SCSI tree will introduce two
replacement drivers for this (Hannes)"
* tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block: (204 commits)
block: setup bounce bio_sets properly
blkcg: reassociate bios when make_request() is called recursively
blkcg: fix edge case for blk_get_rl() under memory pressure
nvme-fabrics: move controller options matching to fabrics
nvme-rdma: always have a valid trsvcid
mtip32xx: fully switch to the generic DMA API
rsxx: switch to the generic DMA API
umem: switch to the generic DMA API
sx8: switch to the generic DMA API
sx8: remove dead IF_64BIT_DMA_IS_POSSIBLE code
skd: switch to the generic DMA API
ubd: remove use of blk_rq_map_sg
nvme-pci: remove duplicate check
drivers/block: Remove DAC960 driver
nvme-pci: fix hot removal during error handling
nvmet-fcloop: suppress a compiler warning
nvme-core: make implicit seed truncation explicit
nvmet-fc: fix kernel-doc headers
nvme-fc: rework the request initialization code
nvme-fc: introduce struct nvme_fcp_op_w_sgl
...
|
|
Commit b9762bebc633 ("gpiolib: Pass bitmaps, not integer arrays, to
get/set array") changed the way GPIO values are passed to
gpiod_get/set_array_value() and friends. The new code introduced into
mmc_pwrseq_simple_set_gpios_value() incorrectly interpretes the 'value'
argument as a bitmap of GPIO values and assigns it directly to the
'values' bitmap variable passed to gpiod_set_array_value_cansleep()
instead of filling that bitmap with bits equal to the 'value' argument.
As a result, only member 0 of the array is handled correctly.
Moreover, wrong assumption is taken about the 'values' bitmap size not
exceding the number of bits of the 'value' argument type.
Fix it.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
the tuning code is becoming more and more bloated, let's make the
set cmd/data delay to inline function to avoid too much redundant code.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
MT8183 puts the tune register at top layer, so need add new code
to support it.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
for MSDC IP which supports both data tune and async fifo, it can
tune cmd/data together. which can save the time and make the tune
result of CMD more stable as data line are 4bit or 8bit.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
when msdc_cmd_is_ready return fail, the req_timeout work has not been
inited and cancel_delayed_work() will return false, then, the request
return directly and never call mmc_request_done().
so need call mod_delayed_work() before msdc_cmd_is_ready()
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
as the mmc core layer has the mmc->actual_clock, so fill it
and drop msdc_host->sclk.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
host->chan_rx is NULL when UNIPHIER_SD_CAP_BROKEN_DMA_RX quirk flag
is set. In this case, it should not set up DMA.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Once DMA is enabled, it is not possible to disable it because
uniphier_sd_dma_endisable() always sets the DMA_ENABLE_DMASDRW bit
regardless of the argument 'enable'. It should disable DMA when
'enable' is false.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
host->chan_{rx,tx} represents the DMA capability of the platform.
Even if DMA is supported, there are cases where we want to use PIO,
for example, data length is short enough as commit 5f52c3552946
("mmc: tmio: use PIO for short transfers") mentioned.
Regarding the hardware control flow, we are interested in whether DMA
is currently enabled or not, instead of whether the platform has the
DMA capability.
Hence, the several conditionals in tmio_mmc_core.c end up with
checking host->chan_{rx,tx} and !host->force_pio. This is not nice.
Let's flip the flag host->force_pio into host->dma_on.
host->dma_on represents whether the DMA is currently enabled or not.
This flag is set false in the beginning of each command, then should
be set true by tmio_mmc_start_dma() when the DMA is turned on.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
TMIO_MMC_HAVE_HIGH_REG is confusing due to its counter-intuitive name.
All the TMIO MMC variants (TMIO MMC, Renesas SDHI, UniPhier SD) actually
have high registers. It is just that each of them implements its own
registers there. The original IP from Panasonic only defines registers
0x00-0xff in the bus_shift=1 review. The register area above them is
platform-dependent.
In fact, TMIO_MMC_HAVE_HIGH_REG is set only by tmio-mmc.c and used to
test the accessibility of CTL_SDIO_REGS. Because it is specific to
the TMIO MFD variant, the right thing to do is to move such registers
to tmio_mmc.c and delete the TMIO_MMC_HAVE_HIGH_REG flag.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
CTL_RESET_SDIO register is specific to the TMIO MFD (tmio_mmc.c).
Add a new hook host->reset() for performing a platform-specific
reset sequence, and move CTL_RESET_SDIO over there.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The RZ/G1C (a.k.a. R8A77470) comes with three SDHI interfaces,
SDHI0 and SDHI2 are compatible with the R-Car Gen2 SDHIs, SDHI1
is compatible with R-Car Gen3 SDHIs and it can be used as
eMMC as well. This patch adds driver compatibility, and makes
sure both drivers get compiled for the R8A77470.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
|
|
On some SD cards over SPI, reading with the multiblock read command the last
sector will leave the card in a bad state.
Remove last sectors from the multiblock reading cmd.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds a stm32 sdmmc variant, rev 1.1.
Introduces a new Manufacturer id "0x53, ascii 'S' to define
new stm32 sdmmc family with clean range of amba
revision/configurations bits (corresponding to sdmmc_ver
register with major/minor fields).
Add 2 variants properties:
-dma_lli, to enable link list support.
-stm32_idmabsize_mask, defines the range of SDMMC_IDMABSIZER register
which specify the number bytes per buffer.
DT properties for sdmmc:
-Indicate signal directions (only one property
for d0dir, d123dir, cmd_dir)
-Select command and data phase relation.
-Select "clock in" from an external driver.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds stm32 sdmmc specific registers.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The STM32 sdmmc variant has a different clock divider.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds a optional reset management.
STM32 sdmmc variant needs to reset hardware block
during the power cycle procedure (for re-initialization).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds a boolean property to not read datacnt register.
Needed to support the STM32 sdmmc variant. MMCIDATACNT
register should be read only after the data transfer is completed.
When reading after an error event the read data count value may be
different from the real number of data bytes transferred.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds a boolean property to allow to write datactrl
before to send command, whatever the command type (read or write).
Needed to support the STM32 sdmmc variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch allows to define specific pio mask for variants.
Needed to support the STM32 sdmmc variant which has some bits
with different meaning (bits: 21,20,13,12,9)
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds datactrl variant property to define
dpsm enable bit. Needed to support the STM32 variant
(STM32 has no dpsm enable bit).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds command variant properties to define
cpsm enable bit and responses.
Needed to support the STM32 variant (shift of cpsm bit,
specific definition of commands response).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
All variants don't pretend to have a startbiterr.
-While data error check, if status register return an error
(like MCI_DATACRCFAIL) we must avoid to check MCI_STARTBITERR
(if not desired).
-expand start_err to MCI_IRQENABLE to avoid to set this bit by default.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch allows to define a datactrl block size
by variant, requested by STM32 sdmmc variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds set_clkreg and set_pwrreg callbacks
at mmci_host_ops to allow to call specific variant.
extends visibility of mmci_write_clk/pwrreg functions
to be used into specific file variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds validate_data callback at mmci_host_ops
to check specific constraints of variant.
Move mmci_validate_data function to regroup mmci_host_ops interfaces.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds dma_error callback at mmci_host_ops
to allow to call specific variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds dma_finalize callback at mmci_host_ops
to allow to call specific variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds dma_start callback to mmci_host_ops.
Create a generic mmci_dma_start function which regroup
common action between variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds get_next_data callback to mmci_host_ops.
Generic mmci_get_next_data factorizes next_cookie check and
the host ops call.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch adds prepare/unprepare callbacks to mmci_host_ops.
Like this mmci_pre/post_request can be generic, mmci_prepare_data
and mmci_unprepare_data provide common next_cookie management.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch merges the prepare data functions.
This allows to define a single access to prepare data service.
This prepares integration for mmci host ops.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
