| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 77693 datasheet describes the interrupt line as active low
with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210602110445.33536-3-krzysztof.kozlowski@canonical.com
|
|
Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Replace GPL v2.0+ license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds muic of_compatible in order to use the muic device
driver in device tree.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Correct smasung.com into samsung.com.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The consumer of max77693 regulators on Trats2 board (samsung-usb2-phy
driver) supports deferred probing so the max77693 main MFD driver can be
built now as a module. This gives more flexibility and removes manual
ordering of init calls.
Suggested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
Core Frameworks:
- New Base API to traverse devices and their children in reverse order
Bug Fixes:
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
Fix-ups:
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures"
* tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: jz4740-adc: Init mask cache in generic IRQ chip
mfd: cros_ec: spi: Add OF match table
mfd: stmpe: Add OF match table
mfd: max77686: Split out regulator part from the DT binding
mfd: Add DT binding for Maxim MAX77802 IC
mfd: max77686: Use a generic name for the PMIC node in the example
mfd: max77686: Don't suggest in binding to use a deprecated property
mfd: Add MFD_CROS_EC dependencies
mfd: cros_ec: Remove CROS_EC_PROTO dependency for SPI and I2C drivers
mfd: axp20x: Add a cell for the usb power_supply part of the axp20x PMICs
mfd: axp20x: Add missing registers, and mark more registers volatile
mfd: arizona: Fixup some formatting/white space errors
mfd: wm8994: Fix NULL pointer exception on missing pdata
of: Add vendor prefix for Nuvoton
mfd: mt6397: Implement wake handler and suspend/resume to handle wake up event
mfd: atmel-hlcdc: Add support for new SoCs
mfd: Export OF module alias information in missing drivers
mfd: stw481x: Export I2C module alias information
mfd: da9062: Support for the DA9063 OnKey in the DA9062 core
mfd: max899x: Avoid redundant irq_data lookup
...
|
|
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This prepares for merging some of the drivers between max77693 and
max77843 so the child MFD driver can be attached to any parent MFD main
driver.
Move the state container to common header file. Additionally add
consistent 'i2c' prefixes to its members (of 'struct i2c_client' type).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Change flash cell identifiers from max77693-flash to max77693-led
to avoid confusion with NOR/NAND Flash.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Changes to the core:
- Honour PLATFORM_DEVID_NONE and PLATFORM_DEVID_AUTO dev IDs
Changes to existing drivers:
- IRQ additions/fixes; axp20x, da9063-core
- Code simplification; i2c-dln2
- Regmap additions/fixes; max77693
- Error checking/handling improvements; dln2, db8500-prcmu
- Bug fixes; dln2, wm8350-core
- DT support/documentation; max77693, max77686, tps65217, twl4030-power,
gpio-tc3589x
- Decouple syscon interface from platform devices
- Use MFD hotplug registration; rtsx_usb, viperboard, hid-sensor-hub
- Regulator fixups; sec-core
- Power Management additions/fixes; rts5227, tc6393xb
- Remove relic/redundant code; ab8500-sysctrl, lpc_sch, max77693-private
- Clean-up/coding style changes; tps65090
- Clk additions/fixes; tc6393xb, tc6387xb, t7l66xb
- Add USB-SPI support; dln2
- Trivial changes; max14577, arizona-spi, lpc_sch, wm8997-tables, wm5102-tables
wm5110-tables, axp20x, atmel-hlcdc, rtsx_pci
New drivers/supported devices:
- axp288 PMIC support added to axp20x
- s2mps13 support added to sec-core
- New support for Diolan DLN-2
- New support for atmel-hlcdc"
* tag 'mfd-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (55 commits)
mfd: rtsx: Add func to split u32 into register
mfd: atmel-hlcdc: Add Kconfig option description and name
mfd: da9063: Get irq base dynamically before registering device
mfd: max14577: Fix obvious typo in company name in copyright
mfd: axp20x: Constify axp20x_acpi_match and rid unused warning
mfd: t7l66xb: prepare/unprepare clocks
mfd: tc6387xb: prepare/unprepare clocks
mfd: dln2: add support for USB-SPI module
mfd: wm5110: Add missing registers for AIF2 channels 3-6
mfd: tc3589x: get rid of static base
mfd: arizona: Document HP_CTRL_1L and HP_CTRL_1R registers
mfd: wm8997: Mark INTERRUPT_STATUS_2_MASK as readable
mfd: tc6393xb: Prepare/unprepare clocks
mfd: tps65090: Fix bonkers indenting strategy
mfd: tc6393xb: Fail ohci suspend if full state restore is required
mfd: lpc_sch: Don't call mfd_remove_devices()
mfd: wm8350-core: Fix probable mask then right shift defect
mfd: ab8500-sysctrl: Drop ab8500_restart
mfd: db8500-prcmu: Provide sane error path values
mfd: db8500-prcmu: Check return of devm_ioremap for error
...
|
|
Add a "maxim,max77693-charger" of_compatible to the mfd_cell so the MFD
child device (the charger) will have its own of_node set. This will be
used by the max77693 charger driver in next patches to obtain battery
configuration from DTS.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch add haptic of_compatible in order to use the haptic
device driver using Devicetree.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch add regmap_haptic initialization to use haptic register map
in haptic device driver.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
All interrupts coming from MUIC were ignored because interrupt source
register was masked.
The Maxim 77693 has a "interrupt source" - a separate register and interrupts
which give information about PMIC block triggering the individual
interrupt (charger, topsys, MUIC, flash LED).
By default bootloader could initialize this register to "mask all"
value. In such case (observed on Trats2 board) MUIC interrupts won't be
generated regardless of their mask status. Regmap irq chip was unmasking
individual MUIC interrupts but the source was masked
Before introducing regmap irq chip this interrupt source was unmasked,
read and acked. Reading and acking is not necessary but unmasking is.
Fixes: 342d669c1ee4 ("mfd: max77693: Handle IRQs using regmap")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Interrupts coming from Maxim77693 MUIC block (MicroUSB Interface
Controller) were not handled at all because wrong regmap was used for
MUIC's regmap_irq_chip.
The MUIC component of Maxim 77693 uses different I2C address thus second
regmap is created and used by max77693 extcon driver. The registers for
MUIC interrupts are also in that block and should be handled by that
second regmap.
However the regmap irq chip for MUIC was configured with default regmap
which could not read MUIC registers.
Fixes: 342d669c1ee4 ("mfd: max77693: Handle IRQs using regmap")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch improves support for the flash cell of
max77693 mfd by adding relevant of_compatible field
and a structure for caching related platform data.
Added are also FLASH registers related macro definitions.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch modifies mfd driver to use regmap for handling interrupts.
It allows to simplify irq handling process. This modifications needed
to make small changes in function drivers, which use interrupts.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch removes wrapper functions used to access regmap, and
make driver using regmap_*() functions instead.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Array of struct of_device_id may be be const as expected by
of_match_table field.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
During probe the driver allocates dummy I2C devices for MUIC and haptic
with i2c_new_dummy() but it does not check the return value of this
calls.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by devm_regmap_init_i2c() and i2c_unregister_device().
If i2c_new_dummy() fails for MUIC or haptic devices, fail also the probe
for main MFD driver.
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The MUIC block in max77693 has different I2C address than PMIC. The
driver allocated two regmaps: for PMIC and MUIC. However it used the
same regmap_config (with max_register field) for both regmaps. Actual
maximum address of register for MUIC is different than for PMIC.
Define another regmap_config for MUIC with proper max_register value.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
As of commit 03e361b25ee8dfb1fd9b890072c23c4aae01c6c7 ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds only of_match_table. There are no device specific
properties.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The patch removes wakeup related code from the driver and plaftorm
data - it is already handled by i2c core using I2C_CLIENT_WAKE flag
from struct i2c_board_info. As a result MFD itself do not requires
platform data.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Current code uses max77693->dev in the dev_err call before setting it to
&i2c->dev. Fix it.
This patch also includes below cleanups:
- Move checking pdata earlier and show dev_err if no platform data found.
- Remove unnecessary err_regmap goto label.
- Unregister i2c devices if regmap init for muic fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch initialize register map of MUIC device because mfd driver
of Maxim MAX77693 use regmap-muic instance of MUIC device when irqs of
Maxim MAX77693 is initialized before call max77693-muic probe() function.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Currently the MFD core supports remapping MFD cell interrupts using an
irqdomain but only if the MFD is being instantiated using device tree
and only if the device tree bindings use the pattern of registering IPs
in the device tree with compatible properties. This will be actively
harmful for drivers which support non-DT platforms and use this pattern
for their DT bindings as it will mean that the core will silently change
remapping behaviour and it is also limiting for drivers which don't do
DT with this particular pattern. There is also a potential fragility if
there are interrupts not associated with MFD cells and all the cells are
omitted from the device tree for some reason.
Instead change the code to take an IRQ domain as an optional argument,
allowing drivers to take the decision about the parent domain for their
interrupts. The one current user of this feature is ab8500-core, it has
the domain lookup pushed out into the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
We need to call max77693_irq_exit() in max77693_i2c_probe error patch and
max77693_i2c_remove.
Current code already uses devm_kzalloc() to allocate memory for max77693.
Thus we should not call kfree(max77693), otherwise we got double free.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
They're not referenced outside this file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Now this driver is using regmap APIs, the iolock mutex is not used and can be
removed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch supports IRQ handling for MAX77693.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch adds MFD driver for MAX77693 to enable its sub devices.
The MAX77693 is a multi-function devices. It includes PMIC,
MUIC(Micro USB Interface Controller), flash LED control and
haptic motor control.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
