| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc and other tiny driver subsystem
updates for 5.16-rc1.
Loads of things in here, all of which have been in linux-next for a
while with no reported problems (except for one called out below.)
Included are:
- habanana labs driver updates, including dma_buf usage, reviewed and
acked by the dma_buf maintainers
- iio driver update (going through this tree not staging as they
really do not belong going through that tree anymore)
- counter driver updates
- hwmon driver updates that the counter drivers needed, acked by the
hwmon maintainer
- xillybus driver updates
- binder driver updates
- extcon driver updates
- dma_buf module namespaces added (will cause a build error in arm64
for allmodconfig, but that change is on its way through the drm
tree)
- lkdtm driver updates
- pvpanic driver updates
- phy driver updates
- virt acrn and nitr_enclaves driver updates
- smaller char and misc driver updates"
* tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (386 commits)
comedi: dt9812: fix DMA buffers on stack
comedi: ni_usb6501: fix NULL-deref in command paths
arm64: errata: Enable TRBE workaround for write to out-of-range address
arm64: errata: Enable workaround for TRBE overwrite in FILL mode
coresight: trbe: Work around write to out of range
coresight: trbe: Make sure we have enough space
coresight: trbe: Add a helper to determine the minimum buffer size
coresight: trbe: Workaround TRBE errata overwrite in FILL mode
coresight: trbe: Add infrastructure for Errata handling
coresight: trbe: Allow driver to choose a different alignment
coresight: trbe: Decouple buffer base from the hardware base
coresight: trbe: Add a helper to pad a given buffer area
coresight: trbe: Add a helper to calculate the trace generated
coresight: trbe: Defer the probe on offline CPUs
coresight: trbe: Fix incorrect access of the sink specific data
coresight: etm4x: Add ETM PID for Kryo-5XX
coresight: trbe: Prohibit trace before disabling TRBE
coresight: trbe: End the AUX handle on truncation
coresight: trbe: Do not truncate buffer on IRQ
coresight: trbe: Fix handling of spurious interrupts
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space and
avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace to
work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction, by
exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP buffer
pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x and
Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we can
add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements to
CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies"
* tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2122 commits)
Revert "net: avoid double accounting for pure zerocopy skbs"
selftests: net: add arp_ndisc_evict_nocarrier
net: ndisc: introduce ndisc_evict_nocarrier sysctl parameter
net: arp: introduce arp_evict_nocarrier sysctl parameter
libbpf: Deprecate AF_XDP support
kbuild: Unify options for BTF generation for vmlinux and modules
selftests/bpf: Add a testcase for 64-bit bounds propagation issue.
bpf: Fix propagation of signed bounds from 64-bit min/max into 32-bit.
bpf: Fix propagation of bounds from 64-bit min/max into 32-bit and var_off.
net: vmxnet3: remove multiple false checks in vmxnet3_ethtool.c
net: avoid double accounting for pure zerocopy skbs
tcp: rename sk_wmem_free_skb
netdevsim: fix uninit value in nsim_drv_configure_vfs()
selftests/bpf: Fix also no-alu32 strobemeta selftest
bpf: Add missing map_delete_elem method to bloom filter map
selftests/bpf: Add bloom map success test for userspace calls
bpf: Add alignment padding for "map_extra" + consolidate holes
bpf: Bloom filter map naming fixups
selftests/bpf: Add test cases for struct_ops prog
bpf: Add dummy BPF STRUCT_OPS for test purpose
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New driver for SK Hynix Hi-846 8M pixel camera
- New driver for the ov13b10 camera
- New driver for Renesas R-Car ISP
- mtk-vcodec gained support for version 2 of decoder firmware ABI
- The legacy sir_ir driver got removed
- videobuf2: the vb2_mem_ops kAPI had some improvements
- lots of cleanups, fixes and new features at device drivers
* tag 'media/v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (328 commits)
media: venus: core: Add sdm660 DT compatible and resource struct
media: dt-bindings: media: venus: Add sdm660 dt schema
media: venus: vdec: decoded picture buffer handling during reconfig sequence
media: venus: Handle fatal errors during encoding and decoding
media: venus: helpers: Add helper to mark fatal vb2 error
media: venus: hfi: Check for sys error on session hfi functions
media: venus: Make sys_error flag an atomic bitops
media: venus: venc: Use pmruntime autosuspend
media: allegro: write vui parameters for HEVC
media: allegro: nal-hevc: implement generator for vui
media: allegro: write correct colorspace into SPS
media: allegro: extract nal value lookup functions to header
media: allegro: correctly scale the bit rate in SPS
media: allegro: remove external QP table
media: allegro: fix row and column in response message
media: allegro: add control to disable encoder buffer
media: allegro: add encoder buffer support
media: allegro: add pm_runtime support
media: allegro: lookup VCU settings
media: allegro: fix module removal if initialization failed
...
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it go through appropriate helpers.
Convert media from memcpy(... 6) and memcpy(... addr_len) to
eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, 6)
+ eth_hw_addr_set(dev, np)
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
Make sure we don't cast off const qualifier from dev->dev_addr.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to better track where in the kernel the dma-buf code is used,
put the symbols in the namespace DMA_BUF and modify all users of the
symbols to properly import the namespace to not break the build at the
same time.
Now the output of modinfo shows the use of these symbols, making it
easier to watch for users over time:
$ modinfo drivers/misc/fastrpc.ko | grep import
import_ns: DMA_BUF
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20211010124628.17691-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the SDM660 DT compatible and its resource structure in order
to support the Venus IP in SDM630, SDM636, SDM660 and SDA variants.
This SoC features Venus 4.4 (HFI3XX) with only one subcore, used
for both encoding and decoding, and switched on with one main and
one subcore dedicated GDSC.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
In existing implementation, driver is freeing and un-mapping all the
decoded picture buffers(DPB) as part of dynamic resolution change(DRC)
handling. As a result, when firmware try to access the DPB buffer, from
previous sequence, SMMU context fault is seen due to the buffer being
already unmapped.
With this change, driver defines ownership of each DPB buffer. If a buffer
is owned by firmware, driver would skip from un-mapping the same.
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
According to stateful decoder docs a fatal failure of decoding
(and encoding) could be recover it by closing the corresponding
file handle and open new one or reinitialize decoding (and encoding)
by stop streaming on both queues. In order to satisfy this
requirement we add a mechanism ins sys_error_handler and
corresponding decoder and encoder drivers to wait for sys_error_done
waitqueue in reqbuf.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Vikash Garodia <vgarodia@codeaurora.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add a helper to mark source and destination vb2 queues fatal
unrecoverable error.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Vikash Garodia <vgarodia@codeaurora.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Check sys error flag for all hfi_session_xxx functions and
exit with EIO in case of an error.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Vikash Garodia <vgarodia@codeaurora.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Make the sys_error flag an atomic bitops in order to avoid
locking in sys_error readers.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Vikash Garodia <vgarodia@codeaurora.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Migrate encoder to pm-runtime autosuspend.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Vikash Garodia <vgarodia@codeaurora.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The vui parameters are optional. However, the vui data allows to specify
the color space of the encoded video. Write the vui parameters to make
sure that decoders are able to pick up the correct color space.
Also implement the necessary lookup functions to convert the values from
the V4L2 controls to the values specified in the hevc standard.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The NAL unit generator for HEVC does not support the generation of vui
parameters. Implement it to allow drivers to set the vui parameters in
the coded video stream.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently, the driver always writes PAL as video format into the SPS of
the encoded stream.
Set the video format to the default value 5 (unspecified) and use the
color description that is already configured on the channel as color
space. This fixes the color space definition in the coded data to
reflect the configured color space of the video data that is encoded.
Add lookup functions to convert the color primaries, transfer function
and matrix coefficients from the V4L2 control values to the values
specified in the h.264 standard.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The lookup of the h.264 or hevc values for the respective V4L2 controls
is done by the driver that uses the sps/pps generator and not in the
generator. Therefore, it is more intuitive to define these functions
directly in the header and not in the module.
Extract the functions to the headers as static inline functions.
Also simplify the function name and add kernel-doc for the hevc
functions.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The bit rate in the SPS can be scaled by an exponent, which allows to
reduce the number of bits in the SPS in case of high bit rates.
The driver did not scale the bitrate, but used a scaling exponent of 0.
Fix this by properly calculating the scaling factor and writing the bit
rate as value and scaling factor into the SPS.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The VCU allows to specify the QP per frame and coding unit. A buffer
that specifies the QP is passed via the ep2 field in the ENCODE_FRAME
message.
The driver currently does not support the external QP table. Simplify
the driver by not setting the ep2 fields at all.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The fields for the number of rows and columns in the encode frame
response message are switched. This causes broken PPS, if the encoder
uses tiles for encoding and the number of rows and columns differ.
Write the fields of the response message into the correct fields of the
the internal data structure when parsing the response message.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The encoder buffer can have a negative impact on the quality of the
encoded video.
Add a control to allow user space to disable the encoder buffer per
channel if the VCU supports the encoder buffer but the quality is not
sufficient.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The encoder buffer serves as a cache for reference frames during the
encoding process. The encoder buffer significantly reduces the bandwidth
requirement for read accesses on the AXI ports of the VCU, but slightly
reduces the quality of the encoded video.
The encoder buffer must be configured as a whole during the firmware
initialization and later explicitly enabled for every channel that shall
use the encoder buffer.
Prior to firmware version 2019.2, it was necessary to explicitly set the
size of the encoder buffer for every channel. Since 2019.2 it is
sufficient to enable the encoder buffer and leave the rest to the
firmware. Therefore, only support the encoder buffer for firmware 2019.2
and later.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The allegro driver must ensure that the mcu and core clocks are enabled
and set to the expected clock rate before trying to load the firmware
and to reset the MCU.
Up until now, the driver assumed that the clocks are always enabled in
the PL (programming logic), because the xlnx_vcu driver did not export
the clocks to other drivers. This has changed and by explicitly enabling
the clocks in the driver, this assumption can be dropped.
It might even be possible to disable the clocks for the encoder if the
encoder is not used. However, the behavior is not documented and it
might be necessary to reinitialize the encoder after deactivating the
clocks. Play it safe by sticking to the current behavior.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The VCU provides information about its configuration in a dedicated
register space. These settings include, for example, the expected clock
rates and the configuration of the encoder buffer. In the device tree,
the settings are described by the "xlnx,vcu-settings" compatible.
The settings are needed to correctly configure the clocks and the
encoder buffer.
Lookup the VCU settings in the device tree and make it accessible to the
driver via a regmap.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
If the module probe finished, but the firmware initialization failed,
removing the module must not revert the firmware initialization.
Add a field to track the status of the firmware initialization and only
roll it back, if the firmware was successfully initialized.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The mailbox is initialized after the interrupt handler is installed. As
the firmware is loaded and started even later, it should not happen that
the interrupt occurs without the mailbox being initialized.
As the Linux Driver Verification project (linuxtesting.org) keeps
reporting this as an error, add a check to ignore interrupts before the
mailbox is initialized to fix this potential null pointer dereference.
Reported-by: Yuri Savinykh <s02190703@gse.cs.msu.ru>
Reported-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
On an Intel NUC6iSYK, no IR is reported after a receive overflow.
When a receiver overflow occurs, this condition is only cleared by
reading the fifo. Make sure we read anything in the fifo.
Fixes: 28c7afb07ccf ("media: ite-cir: check for receive overflow")
Suggested-by: Bryan Pass <bryan.pass@gmail.com>
Tested-by: Bryan Pass <bryan.pass@gmail.com>
Cc: stable@vger.kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This driver is a port of the lirc_sir driver to rc-core. However, for
this driver I could not find any hardware to test, so it was done without
testing. This is a mistake.
There are clear bugs in the code. For example the two arguments
to ktime_us_delta() are reversed, which means the result is garbage.
The driver has been in the kernel for four years, and noone has ever
reported an issue. So, remove this driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
commit f0c15b360fb6 ("media: ir_toy: prevent device from hanging during
transmit") removed a cpu_to_be16() cast, which causes a sparse warning.
Fixes: f0c15b360fb6 ("media: ir_toy: prevent device from hanging during transmit")
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Prevent the use of page table macros and types from 2 conflicting
places. This fixes multiple build errors and warnings, e.g.:
../arch/x86/include/asm/pgtable_64_types.h:21:34: error: conflicting types for ‘pte_t’
typedef struct { pteval_t pte; } pte_t;
^~~~~
In file included from ../include/linux/mm_types_task.h:16:0,
from ../include/linux/mm_types.h:5,
from ../include/linux/buildid.h:5,
from ../include/linux/module.h:14,
from ../drivers/media/pci/ivtv/ivtv-driver.h:40,
from ../drivers/media/pci/ivtv/ivtvfb.c:29:
../arch/um/include/asm/page.h:57:39: note: previous declaration of ‘pte_t’ was here
typedef struct { unsigned long pte; } pte_t;
../arch/x86/include/asm/pgtable_types.h:284:43: error: expected ‘)’ before ‘prot’
static inline pgprot_t pgprot_nx(pgprot_t prot)
^
../include/linux/pgtable.h:914:26: note: in definition of macro ‘pgprot_nx’
#define pgprot_nx(prot) (prot)
^~~~
In file included from ../arch/x86/include/asm/memtype.h:6:0,
from ../drivers/media/pci/ivtv/ivtvfb.c:40:
../arch/x86/include/asm/pgtable_types.h:288:0: warning: "pgprot_nx" redefined
#define pgprot_nx pgprot_nx
../arch/x86/include/asm/page_types.h:11:0: warning: "PAGE_SIZE" redefined
#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT)
In file included from ../include/linux/mm_types_task.h:16:0,
from ../include/linux/mm_types.h:5,
from ../include/linux/buildid.h:5,
from ../include/linux/module.h:14,
from ../drivers/media/pci/ivtv/ivtv-driver.h:40,
from ../drivers/media/pci/ivtv/ivtvfb.c:29:
../arch/um/include/asm/page.h:14:0: note: this is the location of the previous definition
#define PAGE_SIZE (_AC(1, UL) << PAGE_SHIFT)
Fixes: 68f5d3f3b654 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: linux-um@lists.infradead.org
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Save some power by disabling/enabling the jpeg clocks with
every stream stop/start.
Do not use DL_FLAG_RPM_ACTIVE in mxc_jpeg_attach_pm_domains,
to ensure power domains are off after probe.
Signed-off-by: Mirela Rabulea <mirela.rabulea@oss.nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
ADV7610 is another HDMI receiver chip, very similar to
the ADV7611.
Also: print chip names in upper case.
Fix an error message claiming that no ADV761x has been found,
while in reality a chip different than requested (though still
supported) may have been found.
Tested on TinyRex BaseBoard Lite.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The TDA1997x (HDMI receiver) driver currently uses a specific video
format detection scheme. The frame (or field in interlaced mode), line
and HSync pulse durations are compared to those of known, standard video
modes. If a match is found, the mode is assumed to be detected,
otherwise -ERANGE is returned (then possibly ignored). This means that:
- another mode with similar timings will be detected incorrectly
(e.g. 2x faster clock and lines twice as long)
- non-standard modes will not work.
This patch replaces this scheme with a direct read of geometry
registers. This way all modes recognized by the chip are supported.
In interlaced modes, the code assumes the V sync signal has the same
duration for both fields. While this may be not necessarily true,
I can't see any way to get the "other" V sync width. This is most
probably harmless.
All tests have been performed on Gateworks' Ventana GW54xx board, with
a TDA19971 chip.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Newer clang versions are suspicious of definitions that mix concatenated
strings with comma-separated arrays of strings, this has found real bugs
elsewhere, but this seems to be a false positive:
drivers/media/usb/gspca/gl860/gl860-mi1320.c:62:37: error: suspicious concatenation of string literals in an array initialization; did you
mean to separate the elements with a comma? [-Werror,-Wstring-concatenation]
"\xd3\x02\xd4\x28\xd5\x01\xd0\x02" "\xd1\x18\xd2\xc1"
^
,
drivers/media/usb/gspca/gl860/gl860-mi1320.c:62:2: note: place parentheses around the string literal to silence warning
"\xd3\x02\xd4\x28\xd5\x01\xd0\x02" "\xd1\x18\xd2\xc1"
Replace the string literals by compound initializers, using normal hex numbers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Similar configuration to Kworld PC150-U.
Tested: Composite, S-Video, NTSC, ATSC
Unsupported: IR remote
Signed-off-by: Scott K Logan <logans@cottsay.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
To show video real-time information as below:
Capture:
Signal : Unlock
Width : 1920
Height : 1080
FRC : 30
Performance:
Frame# : 0
Frame Duration(ms) :
Now : 0
Min : 0
Max : 0
FPS : 0
[hverkuil: make aspeed_video_proc_open() static, fixes sparse warning]
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
We need to always link allocated vb2_dc_buf back to vb2_buffer because
we dereference vb2 in prepare() and finish() callbacks.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This adds g/s_parm ioctls for parallel interface.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
I came across a link failure from randconfig builds:
x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_remove':
ths8200.c:(.text+0x491): undefined reference to `v4l2_async_unregister_subdev'
x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_probe':
ths8200.c:(.text+0xe49): undefined reference to `v4l2_async_register_subdev'
x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_remove':
tw9910.c:(.text+0x467): undefined reference to `v4l2_async_unregister_subdev'
x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_probe':
tw9910.c:(.text+0x1123): undefined reference to `v4l2_async_register_subdev'
These clearly lack a 'select' statement, but I don't know why
this started happening only now. I had a bit of a look around to find
other configs that have the same problem, but could not come up with
a reliable way and found nothing else through experimentation.
It is likely that other symbols like these exist that need an extra
select.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Adding kfree(dvb) to vidtv_bridge_remove() will remove the memory
too soon: if an application still has an open filehandle to the device
when the driver is unloaded, then when that filehandle is closed, a
use-after-free access takes place to the freed memory.
Move the kfree(dvb) to vidtv_bridge_dev_release() instead.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 76e21bb8be4f ("media: vidtv: Fix memory leak in remove")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
|
|
In dibusb_read_eeprom_byte(), if dibusb_i2c_msg() fails, val gets
assigned an value that's not properly initialized.
Using kzalloc() in place of kmalloc() for the buffer fixes this issue,
as the val can now be set to 0 in the event dibusb_i2c_msg() fails.
Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Tested-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
After freed the dev->urb_list, we should set it to NULL as well as set
counter to zero.
Requested-by: Sean Young <sean@mess.org>
Signed-off-by: Nil Yi <teroincn@163.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
mn88443x_cmn_power_on() did not handle possible errors of
clk_prepare_enable() and always finished successfully so that its caller
mn88443x_probe() did not care about failed preparing/enabling of clocks
as well.
Add missed error handling in both mn88443x_cmn_power_on() and
mn88443x_probe(). This required to change the return value of the former
from "void" to "int".
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0f408ce8941f ("media: dvb-frontends: add Socionext MN88443x ISDB-S/T demodulator driver")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Don't populate the read-only arrays on the stack but instead them
static const. Also makes the object code smaller by 154 bytes:
Before:
text data bss dec hex filename
42949 22424 0 65373 ff5d media/dvb-frontends/mb86a20s.o
After:
text data bss dec hex filename
42731 22488 0 65219 fec3 media/dvb-frontends/mb86a20s.o
(gcc version 11.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Use v4l2 control API helpers to support the events.
Fixes v4l2-compliance:
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
If num_planes is different than zero num_planes and sizes must be
checked to support the format.
Fix the following v4l2-compliance error:
Buffer ioctls (Input 0):
fail: v4l2-test-buffers.cpp(717): q.create_bufs(node, 1, &fmt) != EINVAL
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: FAIL
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add a V4L2 driver for Renesas R-Car Image Signal Processor. The driver
supports the R-Car V3U SoC where the ISP IP sits between the R-Car CSI-2
receiver and VIN and filters the CSI-2 data based on VC/DT and directs
the video stream to different VIN IPs.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The SK Hynix Hi-846 is a 1/4" 8M Pixel CMOS Image Sensor. It supports
usual features like I2C control, CSI-2 for frame data, digital/analog
gain control or test patterns.
This driver supports the 640x480, 1280x720 and 1632x1224 resolution
modes. It supports runtime PM in order not to draw any unnecessary power.
The part is also called YACG4D0C9SHC and a datasheet can be found at
https://product.skhynix.com/products/cis/cis.go
The large sets of partly undocumented register values are for example
found when searching for the hi846_mipi_raw_Sensor.c Android driver.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
