| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The s5p-fimc directory now contains drivers for multiple IP blocks
found in multiple Samsung application processors. This includes FIMC
(CAMIF), MIPI CSIS and FIMC LITE. FIMC-IS (Imaging Subsystem) driver
is going to be put into same directory. Hence we rename it to
exynos4-is as s5p-fimc was only relevant for early version of this
driver, when it only supported FIMC IP block.
The imaging subsystem drivers for Exynos4 SoC series and S5PV210 will
be included in drivers/media/platform/exynos4-is directory, with some
modules shared with exynos5 series, while the rest of exynos5 specific
modules will find their home in drivers/media/platform/exynos5-is.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Drop fimc-lite.h header inclusion to make the exynos-fimc-lite
module independent on other modules. Move struct fimc_fmt
declaration to the driver's private headers as it is used in
multiple modules.
Reported-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Since the FIMC-IS firmware communicates with an image sensor directly
through the ISP I2C bus controllers the sub-devices power supplies
cannot be simply enabled from left to right or disabled from right
to left along the processing pipeline. Thus a subdev index to call
s_power() on is looked up from a table, rather than doing the op call
based on increasing/decreasing indexes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Since the FIMC-IS firmware communicates with an image sensor directly
through the ISP I2C bus controllers data streaming cannot be simply
enabled from left to right or disabled from right to left along the
processing pipeline. Thus a subdev index to call s_stream() on is
looked up from a table, rather than doing the op call based on
increasing/decreasing indexes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
In configurations where FIMC-LITE is used to capture image signal
from an external sensor only we need to ensure one of FIMC devices
is in active power state and the "fimc" gate clock is enabled.
Otherwise the CAMCLK clock output signal will be masked off
preventing an external sensor's operation.
This affect processing pipelines like:
- sensor -> FIMC-LITE -> memory
- sensor -> MIPI-CSIS -> FIMC-LITE -> memory
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
A second sink pad is added to each FIMC.N subdev that will be used
to link it to the FIMC-IS-ISP subdev. Only V4L2_MBUS_FMT_YUV10_1X30
format is supported at this pad (FIMC_SD_PAD_SINK_FIFO).
The routine checking for mismatch in the image formats at sides of
the links is updated to account for the fact FIMC.X subdevs now have
sink pads at the pad indexes 0, 1 and source pad at pad index 2.
If link to FIMC.X pad 1 is activated we switch FIMC input data bus
type to the ISP Writeback. Only a single active link to FIMC.X pad 0
or 1 will be allowed at any time.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch ads handling of clocks for the CAMBLK subsystem which
is a glue logic for FIMC-IS or LCD controller and FIMC IP.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
We cannot assume that the passed entity the fimc_pipeline_prepare()
function is supposed to start the media graph traversal from will
always have its sink pad at pad index 0. Find the starting media
entity's sink pad by iterating over its all pads and checking the
pad flags. This ensures proper handling of FIMC, FIMC-LITE and
FIMC-IS-ISP subdevs that have more than one sink and one source pad.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
set_stream error for pipelines is logged or reported to user
space if possible.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Before the camera ports can be used the pinmux needs to be configured
properly. This patch adds a function to set the camera ports pinctrl
to a default state within the media driver's probe().
The camera port(s) are then configured for the video bus operation.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The sensor (I2C and/or SPI client) devices are instantiated by their
corresponding control bus drivers. Since the I2C client's master clock
is often provided by a video bus receiver (host interface) or other
than I2C/SPI controller device, the drivers of those client devices
are not accessing hardware in their driver's probe() callback. Instead,
after enabling clock, the host driver calls back into a sub-device
when it wants to activate them. This pattern is used by some in-tree
drivers and this patch also uses it for DT case. This patch is intended
as a first step for adding device tree support to the S5P/Exynos SoC
camera drivers. The second one is adding support for asynchronous
sub-devices registration and clock control from sub-device driver
level. The bindings shall not change when asynchronous probing support
is added.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch adds changes required for the main camera media device
driver corresponding to the top level 'camera' device node.
The drivers of devices corresponding to child nodes of the 'camera'
node are looked up and and registered as sub-devices to the top
level driver. The main driver's probing is deferred if any of the
sub-device drivers is not yet initialized and ready.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch adds the device tree support for FIMC-LITE device
driver. The bindings include compatible property for the Exynos5
SoC series, however the actual implementation for these SoCs will
be added in a separate patch.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch adds device tree support for FIMC driver on S5PV210
and Exynos4 SoCs.
The FIMC IP block's features and quirks encoded statically in
the driver are now parsed from the device tree. Once all relevant
platforms are converted to device tree based booting the FIMC
variant data structures will all be removed from the driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch support for binding the driver to the MIPI-CSIS
devices instantiated from device tree and parsing the SoC
and board specific properties. The MIPI CSI-2 channel is
determined by the value of reg property placed in csis'
port subnode.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Replace some ioctl, file and video buffer queue operation handlers
with the videobuf2 helpers. This allows to get rid of significant
amount of boilerplate.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
mmap/poll file operation and several ioctl handlers are replaced
with the vb2 helper functions. Some helpers are used indirectly
to maintain the buffer queue ownership.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
It doesn't matter whether we start from the sensor of from
the video node entity. Remove use of pipeline->subdevs array
where possible, so we can partly drop dependency on struct
fimc_pipeline in the fimc-lite module, which is also used
by the exynos5-is driver.
Also make sure we revert any media entity pipeline operations
when vb2_streamon() function fails.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Not all drivers use monotonic timestamps. This patch adds a way to set the
timestamp type per every queue.
In addition, set proper timestamp type in drivers that I am sure that use
either MONOTONIC or COPY timestamps. Other drivers will correctly report
UNKNOWN timestamp type instead of assuming that all drivers use monotonic
timestamps.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Some cleanups at V4L2 documentation
- new drivers: ts2020 frontend, ov9650 sensor, s5c73m3 sensor,
sh-mobile veu mem2mem driver, radio-ma901, davinci_vpfe staging
driver
- Lots of missing MAINTAINERS entries added
- several em28xx driver improvements, including its conversion to
videobuf2
- several fixups on drivers to make them to better comply with the API
- DVB core: add support for DVBv5 stats, allowing the implementation of
statistics for new standards like ISDB
- mb86a20s: add statistics to the driver
- lots of new board additions, cleanups, and driver improvements.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (596 commits)
[media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff)
[media] rtl28xxu: Add USB IDs for Compro VideoMate U620F
[media] em28xx: add usb id for terratec h5 rev. 3
[media] media: rc: gpio-ir-recv: add support for device tree parsing
[media] mceusb: move check earlier to make smatch happy
[media] radio-si470x doc: add info about v4l2-ctl and sox+alsa
[media] staging: media: Remove unnecessary OOM messages
[media] sh_vou: Use vou_dev instead of vou_file wherever possible
[media] sh_vou: Use video_drvdata()
[media] drivers/media/platform/soc_camera/pxa_camera.c: use devm_ functions
[media] mt9t112: mt9t111 format set up differs from mt9t112
[media] sh-mobile-ceu-camera: fix SHARPNESS control default
Revert "[media] fc0011: Return early, if the frequency is already tuned"
[media] cx18/ivtv: fix regression: remove __init from a non-init function
[media] em28xx: fix analog streaming with USB bulk transfers
[media] stv0900: remove unnecessary null pointer check
[media] fc0011: Return early, if the frequency is already tuned
[media] fc0011: Add some sanity checks and cleanups
[media] fc0011: Fix xin value clamping
Revert "[media] [PATH,1/2] mxl5007 move reset to attach"
...
|
|
Clear the proper array when deregistering FIMC-LITE devices. Now
fimc[] array is erroneously accessed instead of fimc_lite[] and
fimc_md_unregister_entities() function call can result in an oops
from NULL pointer dereference, since fmd->fimc[] is cleared earlier.
This might happen in normal conditions when the driver's probing
is deferred and then retried.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Move e_clkput label after the clk_disable() call so a not acquired clock
is not attempted to be disabled. This fixes runtime warnings like:
s5p-mipi-csis 11880000.csis: failed to get clock: sclk_csis
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:478 clk_disable+0x24/0x34()
Modules linked in:
[<c001603c>] (unwind_backtrace+0x0/0x13c) from [<c0022060>] (warn_slowpath_common+0x54/0x64)
[<c0022060>] (warn_slowpath_common+0x54/0x64) from [<c002208c>] (warn_slowpath_null+0x1c/0x24)
[<c002208c>] (warn_slowpath_null+0x1c/0x24) from [<c033f868>] (clk_disable+0x24/0x34)
[<c033f868>] (clk_disable+0x24/0x34) from [<c02feff8>] (s5pcsis_probe+0x25c/0x4c8)
[<c02feff8>] (s5pcsis_probe+0x25c/0x4c8) from [<c0268e34>] (platform_drv_probe+0x18/0x1c)
[<c0268e34>] (platform_drv_probe+0x18/0x1c) from [<c0267700>] (driver_probe_device+0xa4/0x368)
[<c0267700>] (driver_probe_device+0xa4/0x368) from [<c0267a50>] (__driver_attach+0x8c/0x90)
[<c0267a50>] (__driver_attach+0x8c/0x90) from [<c0265c94>] (bus_for_each_dev+0x60/0x8c)
[<c0265c94>] (bus_for_each_dev+0x60/0x8c) from [<c02665e8>] (bus_add_driver+0x20c/0x2d4)
[<c02665e8>] (bus_add_driver+0x20c/0x2d4) from [<c0268064>] (driver_register+0x78/0x194)
[<c0268064>] (driver_register+0x78/0x194) from [<c0008668>] (do_one_initcall+0x34/0x188)
[<c0008668>] (do_one_initcall+0x34/0x188) from [<c03de57c>] (kernel_init+0x180/0x2f0)
[<c03de57c>] (kernel_init+0x180/0x2f0) from [<c000f0d8>] (ret_from_fork+0x14/0x3c)
---[ end trace 0c5a55345c42530b ]---
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Newer Exynos4 SoC are equipped with a local camera ISP that
controls external raw image sensor directly. Such sensors
can be connected through FIMC-LITEn (and MIPI-CSISn) IPs to
the ISP, which then feeds image data to the FIMCn IP. Thus
there can be two busses associated with an image source
(sensor). Rename struct s5p_fimc_isp_info describing external
image sensor (video decoder) to struct fimc_source_info to
avoid confusion. bus_type is split into fimc_bus_type and
sensor_bus_type. The bus type enumeration is extended to
include both FIMC Writeback input types.
The bus_type enumeration and the data structure name in the
board files are modified according to the above changes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add clk_prepare(), clk_unprepare() calls for the sclk_cam clocks
to ensure the driver works on platforms with the common clocks
API enabled.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The V4L2_SEL_TGT_CROP_BOUNDS, V4L2_SEL_TGT_COMPOSE_BOUNDS selection
targets are not supposed to be handled in the set_selection ioctl.
Remove the code that doesn't do anything sensible now and make sure
ctx->state is modified with the spinlock held.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Make sure a valid image format is initially set on both the CAPTURE
and the OUTPUT buffer queue.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
With presence of some faults, e.g. caused by wrong platform data or
the device tree structure the IDX_SENSOR entry in the array may be NULL,
so make sure it is not dereferenced then.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
clk_set_rate(), clk_enable() functions can fail, so check the return
values to avoid surprises. While at it use ERR_PTR() value to indicate
an invalid clock.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
clk_set_rate(), clk_enable() functions can fail, so check the return
values to avoid surprises. While at it use ERR_PTR() value to indicate
an invalid clock.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The previous method of registering platform entities into the main
driver using driver_find() and then iterating over devices bound to
a driver was racy and is being removed here. Nothing was preventing
module from unloading during a call to try_module_get(driver->owner).
Instead, we look up a device first and then check for its driver while
holding device lock.
The platform sub-devices are looked up and registered to the top
level driver. When any sub-device is not yet initialized and ready
the main driver's probe() will be deferred.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add missing line breaks in the debug traces.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
devm_regulator_bulk_get is device managed and saves some cleanup
and exit code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch fixes regression introduced in commit 6319d6a002beb26631
'[media] fimc-lite: Add ISP FIFO output support'.
In case of a configuration where video is captured at the video node
exposed by the FIMC-LITE driver there is a following video pipeline:
sensor -> MIPI-CSIS.n -> FIMC-LITE.n subdev -> FIMC-LITE.n video node
In this situation s_stream() handler of the FIMC-LITE.n is called
back from within VIDIOC_STREAMON/OFF ioctl of the FIMC-LITE.n video
node, through vb2_stream_on/off(), start/stop_streaming and
fimc_pipeline_call(set_stream). The fimc->lock mutex is already held
then, before invoking vidioc_streamon/off. So it must not be taken
again in the s_stream() callback in this case, to avoid a deadlock.
This patch makes fimc->out_path atomic_t so the mutex don't need
to be taken in the FIMC-LITE subdev s_stream() callback in the DMA
output case.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyugmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The .s_power FIMC-LITE subdev callback is now empty and
unneeded. The FIMC-LITE IP power handling will be done
by the FIMC-IS driver, so just remove the callback.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Make sure bytesperline for Cb, Cr planes for V4L2_PIX_FMT_YUV420M
format is half of the Y plane value, rather than having same
bytesperline for all planes.
While at it, simplify the bytesperline parameter handling by
storing it when image format is set and returning those values
when getting the format, instead of recalculating bytesperline
from intermediate parameters.
Reported-by: Sebastian Dröge <sebastian.droege@collabora.co.uk>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This resolves a gpio driver merge issue pointed out in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
* v4l_for_linus: (464 commits)
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
Linux 3.8-rc3
mm: reinstante dropped pmd_trans_splitting() check
cred: Remove tgcred pointer from struct cred
drm/ttm: fix fence locking in ttm_buffer_object_transfer
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
drm/prime: drop reference on imported dma-buf come from gem
xen/netfront: improve truesize tracking
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
sctp: fix Kconfig bug in default cookie hmac selection
EDAC: Cleanup device deregistering path
...
Conflicts:
drivers/media/pci/dm1105/dm1105.c
drivers/media/platform/soc_camera/mx2_camera.c
|
|
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Kyungmin Park <kyungmin.park@samsung.com>
CC: Sylwester Nawrocki <s.nawrocki@samsung.com>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Linux 3.8-rc3
* tag 'v3.8-rc3': (11110 commits)
Linux 3.8-rc3
mm: reinstante dropped pmd_trans_splitting() check
cred: Remove tgcred pointer from struct cred
drm/ttm: fix fence locking in ttm_buffer_object_transfer
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
drm/prime: drop reference on imported dma-buf come from gem
xen/netfront: improve truesize tracking
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
sctp: fix Kconfig bug in default cookie hmac selection
EDAC: Cleanup device deregistering path
EDAC: Fix EDAC Kconfig menu
EDAC: Fix kernel panic on module unloading
ALSA: hda - add mute LED for HP Pavilion 17 (Realtek codec)
...
|
|
This patch patch eliminates potential AB-BA deadlock when one process calls
open(), or VIDIOC_S/TRY_FMT ioctl on the FIMC capture video node, while
other thread is reconfiguring media links via media device node:
/dev/video? open() /dev/media? MEDIA_IOC_SETUP_LINK ioctl
mutex_lock(video_lock) mutex_lock(graph_lock)
fimc_pipeline_open() fimc_md_link_notify()
mutex_lock(graph_lock) mutex_lock(video_lock)
... ...
The deadlock is avoided by always taking the graph mutex first in video
node open() or an ioctl, before the video lock is acquired. Reversed
order seems impossible, since media device driver's link_notify callback
is called with media graph mutex already held.
To ensure proper locking order VIDIOC_S_FMT and VIDIOC_TRY_FMT ioctls are
not serialized in the v4l2-core and the driver takes care of it itself.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Replace IS_ERR_OR_NULL with IS_ERR on clk_get results.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Replace the hard coded csi_sensors[] array size with a relevant
constant to make sure we don't iterate beyond the actual array.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This fixes following issue found with a static analysis tool:
Pointer 'ffmt' returned from call to function 'fimc_capture_try_format'
at line 1522 may be NULL and may be dereferenced at line 1535.
Although it shouldn't happen in practice, add the NULL pointer check
to be on the safe side.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Make sure 'ret' is not used uninitialized.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
spinlock_t should always be used.
Could not get this to build with allmodconfig:
mcgrof@frijol ~/linux-next (git::(no branch))$ make C=1 M=drivers/media/platform/s5p-fimc/
WARNING: Symbol version dump /home/mcgrof/linux-next/Module.symvers
is missing; modules will have no dependencies and modversions.
LD drivers/media/platform/s5p-fimc/built-in.o
Building modules, stage 2.
MODPOST 0 modules
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Make the pipeline try format routine more generic to support any
number of subdevs in the pipeline, rather than hard coding it for
only a sensor, MIPI-CSIS and FIMC subdevs and the FIMC video node.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Some sensors can have more than one pad (case of S5C73M3).
In such cases FIMC assumes the last pad of the sensor is
the source pad.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
