| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
During the system suspend path we must set all queues to operate in
polled mode as it is possible for any protocol built using this mailbox,
such as TISCI, to require communication during the no irq phase of suspend,
and we cannot rely on interrupts there.
Polled mode is implemented by allowing the mailbox user to define an
RX channel as part of the message that is sent which is what gets polled
for a response. If polled mode is enabled, this will immediately be
polled for a response at the end of the mailbox send_data op before
returning success for the data send or timing out if no response is
received.
Finally, to ensure polled mode is always enabled during system suspend,
iterate through all queues to set RX queues to polled mode during system
suspend and disable polled mode for all in the resume handler.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Refactor the portion of code that actually reads received messages from
a queue into its own function, ti_msgmgr_queue_rx_data, that is called
by the interrupt handler instead of reading directly from the handler.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Add i.MX93 S401 MU cfg
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
i.MX93 S401 MU support two interrupts: tx empty and rx full.
- Introduce a new flag IMX_MU_V2_IRQ for the dual interrupt case
- Update Copyright
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
To i.MX93 S401 MU, there are two interrupts: rx full and tx empty.
So extend irq to an array to prepare i.MX93 S401 MU support.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
i.MX8/8X SECO firmware IPC is an implementation of passing messages.
But current imx-mailbox driver only support one word message,
i.MX8/8X linux side firmware has to request four TX, four RX and a
TXDB to support IPC to SECO firmware. This is low efficent and
more interrupts triggered compared with one TX and one RX.
To make SECO MU work,
- parse the size of msg.
- Only enable TR0/RR0 interrupt for transmit/receive message.
- For TX/RX, only support one TX channel and one RX channel
- For RX, support receive msg of any size, limited by hardcoded value
of 30.
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Add a rxdb callback to prepare for i.MX8 SECO MU rxdb which has a
different logic.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Mailbox driver needs to wait and read all the words in response to a
SCFW API call, else the protocol gets messed up and results in kernel hang.
When the responses are longer than 3 words its possible that SCFW will
take some time to fill up the rest of the words in the MU, a timeout of
100us is arbritrary and too short. While waiting for Linux to consume the
first 3 words of the response SCFW can be busy doing other stuff and hence
Linux needs to wait for the rest of the words.
Similar restriction applies when writing messages that are longer than
3 words.
This patch increases the timeout to 5secs while waiting for response
or writing long messages to SCFW.
Signed-off-by: Ranjani Vaidyanathan <ranjani.vaidyanathan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
check 'priv->clk' before 'imx_mu_read()' otherwise crash happens on
i.mx8ulp, since clock not enabled.
Fixes: 4f0b776ef5831 ("mailbox: imx-mailbox: support i.MX8ULP MU")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Since IRQF_NO_SUSPEND used for imx mailbox driver, that means this irq
can't be used for wakeup source so that can't wakeup from freeze mode.
Add pm_system_wakeup() to wakeup from freeze mode.
Fixes: b7b2796b9b31e("mailbox: imx: ONLY IPC MU needs IRQF_NO_SUSPEND flag")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
This patch is to for MediaTek ADSP IPC mailbox controller driver
It is used to send short messages between processors with adsp
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Reviewed-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
MSM8976 APCS block is similar to one found in MSM8994.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
The txdone can re-fill the mailbox. Keep polling the mailbox during the
flush until all the messages have been delivered.
This fixes an issue with the Tegra Combined UART (TCU) where output can
get truncated under high traffic load.
Signed-off-by: Pekka Pessi <ppessi@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: 91b1b1c3da8a ("mailbox: tegra-hsp: Add support for shared mailboxes")
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- qcom: misc updates to qcom-ipcc driver
- mpfs: change compatible string
- pcc:
- fix handling of subtypes
- avoid uninitialized variable
- mtk:
- add missing of_node_put
- enable control_by_sw
- silent probe-defer prints
- fix gce_num for mt8192
- zynq: add missing of_node_put
- imx: check for NULL instead of IS_ERR
- appple: switch to generic compatibles
- hi3660: convert comments to kernel-doc notation
* tag 'mailbox-v5.17' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
dt-bindings: mailbox: Add more protocol and client ID
mailbox: qcom-ipcc: Support interrupt wake up from suspend
mailbox: qcom-ipcc: Support more IPCC instance
mailbox: qcom-ipcc: Dynamic alloc for channel arrangement
mailbox: change mailbox-mpfs compatible string
mailbox: pcc: Handle all PCC subtypes correctly in pcc_mbox_irq
mailbox: pcc: Avoid using the uninitialized variable 'dev'
mailbox: mtk: add missing of_node_put before return
mailbox: zynq: add missing of_node_put before return
mailbox: imx: Fix an IS_ERR() vs NULL bug
mailbox: hi3660: convert struct comments to kernel-doc notation
mailbox: add control_by_sw for mt8195
mailbox: mtk-cmdq: Silent EPROBE_DEFER errors for clks
mailbox: fix gce_num of mt8192 driver data
mailbox: apple: Bind to generic compatibles
dt-bindings: mailbox: apple,mailbox: Add generic and t6000 compatibles
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI irq updates from Thomas Gleixner:
"Rework of the MSI interrupt infrastructure.
This is a treewide cleanup and consolidation of MSI interrupt handling
in preparation for further changes in this area which are necessary
to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space"
* tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
genirq/msi: Populate sysfs entry only once
PCI/MSI: Unbreak pci_irq_get_affinity()
genirq/msi: Convert storage to xarray
genirq/msi: Simplify sysfs handling
genirq/msi: Add abuse prevention comment to msi header
genirq/msi: Mop up old interfaces
genirq/msi: Convert to new functions
genirq/msi: Make interrupt allocation less convoluted
platform-msi: Simplify platform device MSI code
platform-msi: Let core code handle MSI descriptors
bus: fsl-mc-msi: Simplify MSI descriptor handling
soc: ti: ti_sci_inta_msi: Remove ti_sci_inta_msi_domain_free_irqs()
soc: ti: ti_sci_inta_msi: Rework MSI descriptor allocation
NTB/msi: Convert to msi_on_each_desc()
PCI: hv: Rework MSI handling
powerpc/mpic_u3msi: Use msi_for_each-desc()
powerpc/fsl_msi: Use msi_for_each_desc()
powerpc/pasemi/msi: Convert to msi_on_each_dec()
powerpc/cell/axon_msi: Convert to msi_on_each_desc()
powerpc/4xx/hsta: Rework MSI handling
...
|
|
Use IRQF_NO_SUSPEND flag instead of enable_irq_wake to
support interrupt wake up from suspend.
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Since hardware is supporting multiple IPCC instance,
use ipcc_%d instead of ipcc as the irq name to support
in driver.
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Dynamic alloc for channel arrangement instead of static alloced
array, it is more flexible and can reduce memory usage.
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
The Polarfire SoC is currently using two different compatible string
prefixes. Fix this by changing "polarfire-soc-*" strings to "mpfs-*" in
its system controller in order to match the compatible string used in
the soc binding and device tree.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Commit c45ded7e1135 ("mailbox: pcc: Add support for PCCT extended PCC
subspaces(type 3/4)") enabled the type3/4 of PCCT, but the change in
pcc_mbox_irq breaks the other PCC subtypes.
The kernel reports a warning on an Ampere eMag server
-->8
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.16.0-rc4 #127
Hardware name: MiTAC RAPTOR EV-883832-X3-0001/RAPTOR, BIOS 0.14 02/22/2019
Call trace:
dump_backtrace+0x0/0x200
show_stack+0x20/0x30
dump_stack_lvl+0x68/0x84
dump_stack+0x18/0x34
__report_bad_irq+0x54/0x17c
note_interrupt+0x330/0x428
handle_irq_event_percpu+0x90/0x98
handle_irq_event+0x4c/0x148
handle_fasteoi_irq+0xc4/0x188
generic_handle_domain_irq+0x44/0x68
gic_handle_irq+0x84/0x2ec
call_on_irq_stack+0x28/0x34
do_interrupt_handler+0x88/0x90
el1_interrupt+0x48/0xb0
el1h_64_irq_handler+0x18/0x28
el1h_64_irq+0x7c/0x80
Fixes: c45ded7e1135 ("mailbox: pcc: Add support for PCCT extended PCC subspaces(type 3/4)")
Reported-by: Justin He <justin.he@arm.com>
Tested-by: Justin He <justin.he@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Smatch static checker warns:
| drivers/mailbox/pcc.c:292 pcc_mbox_request_channel()
| error: uninitialized symbol 'dev'.
Fix the same by using pr_err instead of dev_err as the variable 'dev'
is uninitialized at that stage.
Fixes: ce028702ddbc ("mailbox: pcc: Move bulk of PCCT parsing into pcc_mbox_probe")
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Fix following coccicheck warning:
WARNING: Function "for_each_child_of_node"
should have of_node_put() before return.
Early exits from for_each_child_of_node should decrement the
node reference counter.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Fix following coccicheck warning:
WARNING: Function "for_each_available_child_of_node"
should have of_node_put() before return.
Early exits from for_each_available_child_of_node should decrement the
node reference counter.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
The devm_kzalloc() function does not return error pointers, it returns
NULL on failure.
Fixes: 97961f78e8bc ("mailbox: imx: support i.MX8ULP S4 MU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Convert hi3660 struct comments to kernel-doc notation and fix
other kernel-doc warnings:
drivers/mailbox/hi3660-mailbox.c:47: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Hi3660 mailbox channel information
drivers/mailbox/hi3660-mailbox.c:62: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Hi3660 mailbox controller data
hi3660-mailbox.c:53: warning: contents before sections
hi3660-mailbox.c:67: warning: contents before sections
Fixes: 41c0e939d70d ("mailbox: Add support for Hi3660 mailbox")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Ruyi Wang <wangruyi@huawei.com>
Cc: Kaihua Zhong <zhongkaihua@huawei.com>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
To make sure the GCE request signal to SPM is not trigger by
other HW modules and cause suspend premature wake.
Set 0x7 (the bit 0~2 as 1) to GCE_GCTL_VALUE, to configure the
request signal control by SW and release the request to SPM.
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Silent the error if it's EPROBE_DEFER for clks.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Because mt8192 only have 1 gce, the gce_num should be 1.
Fixes: 85dfdbfc13ea ("mailbox: cmdq: add multi-gce clocks support for mt8195")
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
As with other blocks, we intend to have drivers bind to generic
compatibles as long as there are no SoC-specific quirks. This allows
forward-compatibility with future SoCs.
No upstream DTs instantiate this yet, so it's still safe to make this
breaking change.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
No point in retrieving the MSI descriptors. Just query the Linux interrupt
number.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20211210221815.148331680@linutronix.de
|
|
Use the common msi_index member and get rid of the pointless wrapper struct.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20211210221814.413638645@linutronix.de
|
|
The driver uses irq_set_affinity_hint() to:
- Set the affinity_hint which is consumed by the userspace for
distributing the interrupts
- Enforce affinity
As per commit 6ac17fe8c14a ("mailbox: bcm-flexrm-mailbox: Set IRQ affinity
hint for FlexRM ring IRQs") the latter is done to ensure that the FlexRM
ring interrupts are evenly spread across all available CPUs. However, since
commit a0c9259dc4e1 ("irq/matrix: Spread interrupts on allocation") the
spreading of interrupts is dynamically performed at the time of allocation.
Hence, there is no need for the drivers to enforce their own affinity for
the spreading of interrupts.
Also, irq_set_affinity_hint() applying the provided cpumask as an affinity
for the interrupt is an undocumented side effect. To remove this side
effect irq_set_affinity_hint() has been marked as deprecated and new
interfaces have been introduced. Hence, replace the irq_set_affinity_hint()
with the new interface irq_update_affinity_hint() that only sets the
affinity_hint pointer.
Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Link: https://lore.kernel.org/r/20210903152430.244937-11-nitesh@redhat.com
|
|
Like i.MX8 SCU, i.MX8ULP S4 also has vendor specific protocol.
- bind SCU/S4 MU part to share one tx/rx/init API to make code simple.
- S4 msg max size is very large, so alloc the space at driver probe,
not use local on stack variable.
- S4 MU has 8 TR and 4 RR which is different with i.MX8 MU, so adapt
code to reflect this.
Tested on i.MX8MP, i.MX8ULP
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Move the PCCT subspace parsing and allocation into pcc_mbox_probe so
that we can get rid of global PCC channel and mailbox controller data.
It also helps to make use of devm_* APIs for all the allocations.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
With all the plumbing in place to avoid accessing PCCT type and other
fields directly from the PCCT table all the time, let us now add the
support for extended PCC subspaces(type 3 and 4).
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
pcc_chan_reg_init now checks if the register bit width is within the
list [8, 16, 32, 64] and flags error if that is not the case. Therefore
there is no need to handling invalid bit-width in both read_register
and write_register. We can drop that along with the return values for
these 2 functions.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Now that the con_priv is availvale solely for PCC mailbox controller
driver, let us use the same to save the channel specific information
in it so that we can it whenever required instead of parsing the PCCT
table entries every time in both pcc_send_data and pcc_mbox_irq.
We can now use the newly introduces PCC register bundle to simplify both
saving of channel specific information and accessing them without repeated
checks for the subspace type.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Extended PCC subspaces introduces more registers into the PCCT. In order
to consolidate access to these registers and to keep all the details
contained in one place, let us introduce PCC register bundle that holds
the ACPI Generic Address Structure as well as the virtual address for
the same if it is mapped in the OS.
It also contains the various masks used to access the register and
the associated read, write and read-modify-write accessors.
We can also clean up the initialisations by having a helper function
for the same.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
The specification refers this register and associated bitmask as platform
interrupt acknowledge register. Let us rename it so that it is easier to
map and understand.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Now that we have all the shared memory region information populated in
the pcc_mbox_chan, let us propagate the pointer to the same as the
return value to pcc_mbox_request channel.
This eliminates the need for the individual users of PCC mailbox to
parse the PCCT subspace entries and fetch the shmem information. This
also eliminates the need for PCC mailbox controller to set con_priv to
PCCT subspace entries. This is required as con_priv is private to the
controller driver to attach private data associated with the channel and
not meant to be used by the mailbox client/users.
Let us convert all the users of pcc_mbox_{request,free}_channel to use
new interface.
Cc: Jean Delvare <jdelvare@suse.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Currently PCC mailbox controller sets con_priv in each channel to hold
the pointer to pcct subspace entry it corresponds to. The mailbox user
will then fetch this pointer from the channel descriptor they get when
they request for the channel. Using that pointer they then parse the
pcct entry again to fetch all the information about shared memory region.
In order to remove individual users of PCC mailbox parsing the PCCT
subspace entries to fetch same information, let us consolidate the same
in pcc mailbox controller by parsing all the shared memory region
information into a structure that can also hold the mbox_chan pointer it
represent.
This can then be used as main PCC mailbox channel pointer that we can
return as part of pcc_mbox_request_channel instead of standard mailbox
channel pointer.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Extended PCC subspaces(Type 3 and 4) differ from generic(Type 0) and
HW-Reduced Communication(Type 1 and 2) subspace structures. However some
fields share same offsets and same type of structure can be use to
extract the fields. In order to simplify that, let us move all the doorbell
register parsing into pcc_parse_subspace_db_reg and consolidate there.
It will be easier to extend it if required within the same.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Extended PCC subspaces(Type 3 and 4) differ from generic(Type 0) and
HW-Reduced Communication(Type 1 and 2) subspace structures. However some
fields share same offsets and same type of structure can be use to extract
the fields. In order to simplify that, let us move all the IRQ related
information parsing into pcc_parse_subspace_irq and consolidate there.
It will be easier to extend it if required within the same.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Currently all the PCC channel specific information are stored/maintained
in global individual arrays for each of those information. It is not
scalable and not clean if we have to stash more channel specific
information. Couple of reasons to stash more information are to extend
the support to Type 3/4 PCCT subspace and also to avoid accessing the
PCCT table entries themselves each time we need the information.
This patch moves all those PCC channel specific information into a
separate structure pcc_chan_info.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Kernel doc validation script is unhappy and complains with the below set
of warnings.
| drivers/mailbox/pcc.c:179: warning: Function parameter or member 'irq'
| not described in 'pcc_mbox_irq'
| drivers/mailbox/pcc.c:179: warning: Function parameter or member 'p'
| not described in 'pcc_mbox_irq'
| drivers/mailbox/pcc.c:378: warning: expecting prototype for
| parse_pcc_subspaces(). Prototype was for parse_pcc_subspace() instead
Fix it.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Apple SoCs such as the M1 come with various co-processors. Mailboxes
are used to communicate with those. This driver adds support for
two variants of those mailboxes.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
In the probe function, the clock IDs were pointed to local variables
which should only be used in the same code block, and any access to them
after the probing stage becomes an use-after-free case.
Since there are only limited variants of the gce clock names so far, we
can just declare them as static constants to fix the issue.
Fixes: 85dfdbfc13ea ("mailbox: cmdq: add multi-gce clocks support for mt8195")
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
of_alias_get_id() may return -ENODEV which leads to illegal access to
the cmdq->clocks array.
Adding a check over alias_id to prevent the unexpected behavior.
Fixes: 85dfdbfc13ea ("mailbox: cmdq: add multi-gce clocks support for mt8195")
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Because mtk_drm_crtc_update_config is not using cmdq_pkt_flush_async,
it won't have pkt->async_cb.cb anymore.
So remove the WARN_ON check of pkt->async_cb.cb at cmdq_exec_done.
Fixes: 1b6b0ce2240e ("mailbox: mtk-cmdq: Use mailbox rx_callback")
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Enable QCM2290 APCS IPC support by adding the compatible. It reuses
msm8994_apcs_data.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
