| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A small fixup to ili210x touchscreen driver, and updated maintainer
entry for the device tree binding of Mediatek 6779 keypad:
- fix reset timing of Ilitek touchscreens
- update maintainer entry of DT binding of Mediatek 6779 keypad"
* tag 'input-for-v5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ili210x - use one common reset implementation
Input: ili210x - fix reset timing
dt-bindings: input: mediatek,mt6779-keypad: update maintainer
|
|
Merge changes to ChromeOS EC Keyboard driver.
|
|
Rename ili251x_hardware_reset() to ili210x_hardware_reset(), change its
parameter from struct device * to struct gpio_desc *, and use it as one
single consistent reset implementation all over the driver. Also increase
the minimum reset duration to 12ms, to make sure the reset is really
within the spec.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518210423.106555-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.
This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.
Fixes: 201f3c803544c ("Input: ili210x - add reset GPIO support")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220518204901.93534-1-marex@denx.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Now that we are using oneshot threaded IRQ this method is not used anymore.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[arnd: add the db1300 change as well]
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Instead of manually disabling and enabling interrupts and scheduling work
to access the device, let's use threaded oneshot interrupt handler. It
simplifies things.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
To avoid a dependency on the pxa platform header files with
hardcoded registers, change the driver to call a wrapper
in the pxa2xx-ac97-lib that encapsulates all the other
ac97 stuff.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: linux-input@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The two drivers are almost identical and can work on a variety
of hardware in principle. The mainstone driver supports additional
hardware, and the zylonite driver has a few cleanup patches.
Sync the two by adding the zylonite changes into the mainstone
one, and checking for the zylonite board to order to keep the
default behavior (interrupt enabled) there.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-input@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There are two different ways of flushing the ac97 queue
in this driver, selected by a compile time option.
Change this to a runtime selection to make it work when both
are enabled.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: linux-input@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The mach/mfp.h header is only used by this one driver
for hardcoded gpio numbers. Change that to use a lookup
table instead.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-input@vger.kernel.org
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This driver hardcodes gpio numbers without a header file.
Use lookup tables instead.
Cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-input@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The mach/hardware.h is included in lots of places, and it provides
three different things on pxa:
- the cpu_is_pxa* macros
- an indirect inclusion of mach/addr-map.h
- the __REG() and io_pv2() helper macros
Split it up into separate <linux/soc/pxa/cpu.h> and mach/pxa-regs.h
headers, then change all the files that use mach/hardware.h to
include the exact set of those three headers that they actually
need, allowing for further more targeted cleanup.
linux/soc/pxa/cpu.h can remain permanently exported and is now in
a global location along with similar headers. pxa-regs.h and
addr-map.h are only used in a very small number of drivers now
and can be moved to arch/arm/mach-pxa/ directly when those drivers
are to pass the necessary data as resources.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-leds@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a revert of a patch resetting extra buttons on touchpads claiming to
be buttonpads as this caused regression on certain Dell devices
- a new driver for Mediatek MT6779 keypad
- a new driver for Imagis touchscreen
- rework of Google/Chrome OS "Vivaldi" keyboard handling
- assorted driver fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (31 commits)
Revert "Input: clear BTN_RIGHT/MIDDLE on buttonpads"
Input: adi - remove redundant variable z
Input: add Imagis touchscreen driver
dt-bindings: input/touchscreen: bindings for Imagis
Input: synaptics - enable InterTouch on ThinkPad T14/P14s Gen 1 AMD
Input: stmfts - fix reference leak in stmfts_input_open
Input: add bounds checking to input_set_capability()
Input: iqs5xx - use local input_dev pointer
HID: google: modify HID device groups of eel
HID: google: Add support for vivaldi to hid-hammer
HID: google: extract Vivaldi hid feature mapping for use in hid-hammer
Input: extract ChromeOS vivaldi physmap show function
HID: google: switch to devm when registering keyboard backlight LED
Input: mt6779-keypad - fix signedness bug
Input: mt6779-keypad - add MediaTek keypad driver
dt-bindings: input: Add bindings for Mediatek matrix keypad
Input: da9063 - use devm_delayed_work_autocancel()
Input: goodix - fix race on driver unbind
Input: goodix - use input_copy_abs() helper
Input: add input_copy_abs() function
...
|
|
Prepare input updates for 5.18 merge window.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- a major reorg at platform Kconfig/Makefile files, organizing them per
vendor. The other media Kconfig/Makefile files also sorted
- New sensor drivers: hi847, isl7998x, ov08d10
- New Amphion vpu decoder stateful driver
- New Atmel microchip csi2dc driver
- tegra-vde driver promoted from staging
- atomisp: some fixes for it to work on BYT
- imx7-mipi-csis driver promoted from staging and renamed
- camss driver got initial support for VFE hardware version Titan 480
- mtk-vcodec has gained support for MT8192
- lots of driver changes, fixes and improvements
* tag 'media/v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (417 commits)
media: nxp: Restrict VIDEO_IMX_MIPI_CSIS to ARCH_MXC or COMPILE_TEST
media: amphion: cleanup media device if register it fail
media: amphion: fix some issues to improve robust
media: amphion: fix some error related with undefined reference to __divdi3
media: amphion: fix an issue that using pm_runtime_get_sync incorrectly
media: vidtv: use vfree() for memory allocated with vzalloc()
media: m5mols/m5mols.h: document new reset field
media: pixfmt-yuv-planar.rst: fix PIX_FMT labels
media: platform: Remove unnecessary print function dev_err()
media: amphion: Add missing of_node_put() in vpu_core_parse_dt()
media: mtk-vcodec: Add missing of_node_put() in mtk_vdec_hw_prob_done()
media: platform: amphion: Fix build error without MAILBOX
media: spi: Kconfig: Place SPI drivers on a single menu
media: i2c: Kconfig: move camera drivers to the top
media: atomisp: fix bad usage at error handling logic
media: platform: rename mediatek/mtk-jpeg/ to mediatek/jpeg/
media: media/*/Kconfig: sort entries
media: Kconfig: cleanup VIDEO_DEV dependencies
media: platform/*/Kconfig: make manufacturer menus more uniform
media: platform: Create vendor/{Makefile,Kconfig} files
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus
types, causing updates to most SPI device drivers. The branch with
that on has been cross merged with a couple of other trees which added
new SPI drivers this cycle, I'm not expecting any build issues
resulting from the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than
numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021"
[ And this is obviously where that spi change that snuck into the
regulator tree _should_ have been :^]
* tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits)
spi: fsi: Implement a timeout for polling status
spi: Fix erroneous sgs value with min_t()
spi: tegra20: Use of_device_get_match_data()
spi: mediatek: add ipm design support for MT7986
spi: Add compatible for MT7986
spi: sun4i: fix typos in comments
spi: mediatek: support tick_delay without enhance_timing
spi: Update clock-names property for arm pl022
spi: rockchip-sfc: fix platform_get_irq.cocci warning
spi: s3c64xx: Add spi port configuration for Tesla FSD SoC
spi: dt-bindings: samsung: Add fsd spi compatible
spi: topcliff-pch: Prevent usage of potentially stale DMA device
spi: tegra210-quad: combined sequence mode
spi: tegra210-quad: add acpi support
spi: npcm-fiu: Fix typo ("npxm")
spi: Fix Tegra QSPI example
spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ
spi: cadence: fix platform_get_irq.cocci warning
spi: Update NXP Flexspi maintainer details
dt-bindings: mfd: maxim,max77802: Convert to dtschema
...
|
|
Add support for the IST3038C touchscreen IC from Imagis, based on
downstream driver. The driver supports multi-touch (10 touch points)
The IST3038C IC supports touch keys, but the support isn't added
because the touch screen used for testing doesn't utilize touch keys.
Looking at the downstream driver, it is possible to add support
for other Imagis ICs of IST30**C series.
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Link: https://lore.kernel.org/r/20220305165330.13061-3-markuss.broks@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
pm_runtime_get_sync() will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put_noidle will result
in reference leak in stmfts_input_open, so we should fix it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20220317131604.53538-1-zhengyongjun3@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Both iqs5xx_axis_init() and iqs5xx_irq() already define a local
input_dev pointer 'input'. Use this instead of iqs5xx->input so
as to make the code a bit smaller.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20220320025707.404544-1-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
media Kconfig has two entries associated to V4L API:
VIDEO_DEV and VIDEO_V4L2.
On Kernel 2.6.x, there were two V4L APIs, each one with its own flag.
VIDEO_DEV were meant to:
1) enable Video4Linux and make its Kconfig options to appear;
2) it makes the Kernel build the V4L core.
while VIDEO_V4L2 where used to distinguish between drivers that
implement the newer API and drivers that implemented the former one.
With time, such meaning changed, specially after the removal of
all V4L version 1 drivers.
At the current implementation, VIDEO_DEV only does (1): it enables
the media options related to V4L, that now has:
menu "Video4Linux options"
visible if VIDEO_DEV
source "drivers/media/v4l2-core/Kconfig"
endmenu
but it doesn't affect anymore the V4L core drivers.
The rationale is that the V4L2 core has a "soft" dependency
at the I2C bus, and now requires to select a number of other
Kconfig options:
config VIDEO_V4L2
tristate
depends on (I2C || I2C=n) && VIDEO_DEV
select RATIONAL
select VIDEOBUF2_V4L2 if VIDEOBUF2_CORE
default (I2C || I2C=n) && VIDEO_DEV
In the past, merging them would be tricky, but it seems that it is now
possible to merge those symbols, in order to simplify V4L dependencies.
Let's keep VIDEO_DEV, as this one is used on some make *defconfig
configurations.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for meson-vdec & meson-ge2d
Acked-by: Andrzej Pietrasiewicz <andrzejtp2010@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Sync up with mainline to again get the latest changes in HID subsystem.
|
|
I observed the following problem with the BT404 touch pad
running the Phosh UI:
When e.g. typing on the virtual keyboard pressing "g" would
produce "ggg".
After some analysis it turns out the firmware reports that three
fingers hit that coordinate at the same time, finger 0, 2 and
4 (of the five available 0,1,2,3,4).
DOWN
Zinitix-TS 3-0020: finger 0 down (246, 395)
Zinitix-TS 3-0020: finger 1 up (0, 0)
Zinitix-TS 3-0020: finger 2 down (246, 395)
Zinitix-TS 3-0020: finger 3 up (0, 0)
Zinitix-TS 3-0020: finger 4 down (246, 395)
UP
Zinitix-TS 3-0020: finger 0 up (246, 395)
Zinitix-TS 3-0020: finger 2 up (246, 395)
Zinitix-TS 3-0020: finger 4 up (246, 395)
This is one touch and release: i.e. this is all reported on
touch (down) and release.
There is a field in the struct touch_event called finger_cnt
which is actually a bitmask of the fingers active in the
event.
Rename this field finger_mask as this matches the use contents
better, then use for_each_set_bit() to iterate over just the
fingers that are actally active.
Factor out a finger reporting function zinitix_report_fingers()
to handle all fingers.
Also be more careful in reporting finger down/up: we were
reporting every event with input_mt_report_slot_state(..., true);
but this should only be reported on finger down or move,
not on finger up, so also add code to check p->sub_status
to see what is happening and report correctly.
After this my Zinitix BT404 touchscreen report fingers
flawlessly.
The vendor drive I have notably does not use the "finger_cnt"
and contains obviously incorrect code like this:
if (touch_dev->touch_info.finger_cnt > MAX_SUPPORTED_FINGER_NUM)
touch_dev->touch_info.finger_cnt = MAX_SUPPORTED_FINGER_NUM;
As MAX_SUPPORTED_FINGER_NUM is an ordinal and the field is
a bitmask this seems quite confused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220228233017.2270599-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Because there is no way to detect if the touchscreen has pen support,
the driver is allocating and registering the input_pen input_dev on
receiving the first pen event.
But this means that the input_dev gets allocated after the request_irq()
call which means that the devm framework will free it before disabling
the irq, leaving a window where the irq handler may run and reference the
free-ed input_dev.
To fix this move the allocation of the input_pen input_dev to before
the request_irq() call, while still only registering it on the first pen
event so that the driver does not advertise pen capability on touchscreens
without it (most goodix touchscreens do not have pen support).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131143539.109142-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Use the new input_copy_abs() helper and move the 2 input_abs_set_res()
calls up to be directly after the 2 input_copy_abs() calls, so that
the calls initializing the X and Y axis are all together.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131143539.109142-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Interrupt() resource
ACPI/x86 devices with a Cherry Trail SoC should have a GpioInt + a regular
GPIO ACPI resource in their ACPI tables.
Some CHT devices have a bug, where the also is bogus interrupt resource
(likely copied from a previous Bay Trail based generation of the device).
The i2c-core-acpi code will assign the bogus, non-working, interrupt
resource to client->irq. Add a workaround to fix this up.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=2043960
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220228111613.363336-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Use the new soc_intel_is_byt() helper from linux/platform_data/x86/soc.h.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220131143539.109142-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Merge with mainline to get the Intel ASoC generic helpers header and
other changes.
|
|
Sync up with mainline to get the latest changes in HID subsystem.
|
|
Since Commit ed7c9870c9bc ("Input: of_touchscreen - add support for
inverted / swapped axes"), the of_touchscreen interface supports axis
inverting and swapping through device tree properties. Make use of this
feature.
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Link: https://lore.kernel.org/r/20220209223933.1672782-1-y.bas@phytec.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This driver works just fine with the BT404 version of the touchscreen
as well. Tested on the Samsung GT-I8160 (Codina) mobile phone.
Add all the new variants from the binding document so people can
easily test them, we believe most of them work more or less.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220214234033.1052681-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.17
Quite a few fixes here, including an unusually large set in the core
spurred on by various testing efforts as well as the usual small driver
fixes. There are quite a few fixes for out of bounds writes in both the
core and the various Qualcomm drivers, plus a couple of fixes for
locking in the DPCM code.
|
|
Since the commit in the Fixes tag below, 'wm->input_dev' is a managed
resource that doesn't need to be explicitly unregistered or freed (see
devm_input_allocate_device() documentation)
So, remove some unless line of code to slightly simplify it.
Fixes: c72f61e74073 ("Input: wm97xx: split out touchscreen registering")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87dce7e80ea9b191843fa22415ca3aef5f3cc2e6.1643529968.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Sync up with mainline to bring in the latest API changes.
|
|
Prepare input updates for 5.17 merge window.
|
|
change 'postion' to 'position'
Signed-off-by: Qinghua Jin <qhjin.dev@gmail.com>
Link: https://lore.kernel.org/r/20220106084215.355295-1-qhjin.dev@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"A small fixup to the Zinitix touchscreen driver to avoid enabling the
IRQ line before we successfully requested it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: zinitix - make sure the IRQ is allocated before it gets enabled
|
|
Zinitix BT532 is another touch controller that seem to implement the
same interface as an already supported BT541. Add it to the driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-5-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The supply names of the Zinitix touchscreen were a bit confused, the new
bindings rectifies this.
To deal with old and new devicetrees, first check if we have "vddo" and in
case that exists assume the old supply names. Else go and look for the new
ones.
We cannot just get the regulators since we would get an OK and a dummy
regulator: we need to check explicitly for the old supply name.
Use struct device *dev as a local variable instead of the I2C client since
the device is what we are actually obtaining the resources from.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Slightly changed the legacy regulator detection]
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-4-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.
Fix that by moving the irq request before the input device registration.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652c85e ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A few small updates to drivers.
Of note we are now deferring probes of i8042 on some Asus devices as
the controller is not ready to respond to queries first time around
when the driver is compiled into the kernel"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elants_i2c - do not check Remark ID on eKTH3900/eKTH5312
Input: atmel_mxt_ts - fix double free in mxt_read_info_block
Input: goodix - fix memory leak in goodix_firmware_upload
Input: goodix - add id->model mapping for the "9111" model
Input: goodix - try not to touch the reset-pin on x86/ACPI devices
Input: i8042 - enable deferred probe quirk for ASUS UM325UA
Input: elantech - fix stack out of bound access in elantech_change_report_id()
Input: iqs626a - prohibit inlining of channel parsing functions
Input: i8042 - add deferred probe support
|
|
The eKTH3900/eKTH5312 series do not support the firmware update rules of
Remark ID. Exclude these two series from checking it when updating the
firmware in touch controllers.
Signed-off-by: Johnny Chuang <johnny.chuang.emc@gmail.com>
Link: https://lore.kernel.org/r/1639619603-20616-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Variable penup is assigned a value but penup is never read later, it
is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211205000525.153999-1-colin.i.king@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The open delay time has to be applied only on the first sample of the
X/Y coordinates because on the following samples the ADC channel is not
changed. Removing this time from the samples after the first one,
"ti,coordinate-readouts" greater than 1, decreases the total acquisition
time, allowing to increase the number of acquired coordinates in the time
unit.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-4-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The Z2 step configuration doesn't erase the SEL_INP_SWC_3_0 bit-field
before setting the ADC channel. This way its value could be corrupted by
the ADC channel selected for the Z1 coordinate.
Fixes: 8c896308feae ("input: ti_am335x_adc: use only FIFO0 and clean up a little")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-3-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
As reported by the STEPCONFIG[1-16] registered field descriptions of the
TI reference manual, for the ADC "in single ended, SEL_INM_SWC_3_0 must
be 1xxx".
Unlike the Y and Z coordinates, this bit has not been set for the step
configuration registers used to sample the X coordinate.
Fixes: 1b8be32e6914 ("Input: add support for TI Touchscreen controller")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-2-dariobin@libero.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Some Silead touchscreens have support for an active (battery powered)
pen, add support for this.
So far pen-support has only been seen on X86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new properties are deliberately not added
to the existing silead devicetree-bindings documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211122220637.11386-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
coordinates
Unfortunately, at the time of writing this commit message, we have been
unable to get permission from Silead, or from device OEMs, to distribute
the necessary Silead firmware files in linux-firmware.
On a whole bunch of devices the UEFI BIOS code contains a touchscreen
driver, which contains an embedded copy of the firmware. The fw-loader
code has a "platform" fallback mechanism, which together with info on the
firmware from drivers/platform/x86/touchscreen_dmi.c will use the firmware
from the UEFI driver when the firmware is missing from /lib/firmware. This
makes the touchscreen work OOTB without users needing to manually download
the firmware.
The firmware bundled with the original Windows/Android is usually newer
then the firmware in the UEFI driver and it is better calibrated. This
better calibration can lead to significant differences in the reported
min/max coordinates.
Add support for a new (optional) "silead,efi-fw-min-max" property which
provides a set of alternative min/max values to use for the x/y axis when
the EFI embedded firmware is used.
The new property is only used on (x86) devices which do not use devicetree,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added to the
existing silead devicetree-bindings documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211122220637.11386-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
2 small fixes for pen support
1. Set the id.vendor field for the pen input_dev
2. Fix a typo in a comment
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211212124242.81019-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
goodix_get_gpio_config() errors are fatal (abort probe()) so log them
at KERN_ERR level rather then as debug messages.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211212124242.81019-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
