| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Modern devices may redraw display at 60 Hz, make sure we have one input
sample per one frame. Reduce sample period to 15ms, so we would get up
to 66.6 samples per second, although realistically with all the jitter
and extra scheduling wiggle room, we would end up just above 60 samples
per second. This should be a good compromise between sampling too often
and sampling too seldom.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108114145.84118-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Currently the ili210x driver implements a threaded interrupt handler which
starts upon edge on the interrupt line, and then polls the touch controller
for samples. Every time a sample is obtained from the controller, the thread
function checks whether further polling is required, and if so, waits fixed
amount of time before polling for next sample.
The delay between consecutive samples can thus vary greatly, because the
I2C transfer required to retrieve the sample from the controller takes
different amount of time on different platforms. Furthermore, different
models of the touch controllers supported by this driver require different
delays during retrieval of samples too.
Instead of waiting fixed amount of time before polling for next sample,
determine how much time passed since the beginning of sampling cycle and
then wait only the remaining amount of time within the sampling cycle.
This makes the driver deliver samples with equal spacing between them.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005216.480525-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The ili251x touch controller needs 5ms delay between sending I2C device
address and register address, and, writing or reading register data.
According to downstream ili251x example code, this 5ms delay is not
required when reading touch samples out of the controller. Implement
such a special case.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005259.480545-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The ili251x firmware can be updated, this is used when switching between
different modes of operation of the touch surface, e.g. glove operation.
This patch implements the firmware update mechanism triggered by a write
into an sysfs attribute.
The firmware itself is distributed as an intel hex file with non-standard
types. The first two lines are of type 0xad, which indicates the start of
DataFlash payload, that is always at address 0xf000 on the ili251x, so it
can be dropped, and 0xac which indicates the position of firmware info in
the Application payload, that is always at address 0x2020 on the ili251x
and we do not care. The rest of the firmware is data of type 0x00, and we
care about that. To convert the firmware hex file into something usable
by the kernel, remove the first two lines and then use ihex2fw:
$ tail -n +3 input.hex > temp.hex
$ ./tools/firmware/ihex2fw temp.hex firmware/ilitek/ili251x.bin
To trigger the firmware update, place firmware file ilitek/ili251x.bin
into /lib/firmware/, write into firmware_update sysfs attribute and wait
about 30-40 seconds. The firmware update is slow. Afterward, verify the
firmware_version and mode sysfs attributes to check whether the firmware
got updated and the controller switched back to application (AP) mode by
reading out 'mode' attribute in sysfs.
Note that the content of firmware_version, e.g. 0600.0005.abcd.aa04 can
be matched to the content of the firmware hex file. The first four bytes,
0x06 0x00 0x00 0x05 can be found at ^:102030 00 05000006, the next four
bytes 0xab 0xcd 0xaa 0x04 at ^:10F000 00 nnnnnnnn ABCDAA04.
Note that the protocol differs considerably between the ili2xxx devices,
this patch therefore implements this functionality only for ili251x that
I can test.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-3-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The ili251x firmware protocol permits readout of firmware version,
protocol version, mcu version and current mode (application, boot
loader, forced update). These information are useful when updating
the firmware on the il251x, e.g. to avoid updating the same firmware
into the device multiple times. The locking is now necessary to avoid
races between interrupt handler and the sysfs readouts.
Note that the protocol differs considerably between the ili2xxx devices,
this patch therefore implements this functionality only for ili251x that
I can test.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-2-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The ili251x firmware protocol permits readout of panel resolution,
implement this, but make it possible to override this value using
DT bindings. This way, older DTs which contain touchscreen-size-x
and touchscreen-size-y properties will behave just like before and
new DTs may avoid specifying these for ILI251x.
Note that the command format is different on other controllers, so
this functionality is isolated to ILI251x.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This adds the negation needed for proper finger detection on Ilitek
ili2107/ili210x. This fixes polling issues (on Amazon Kindle Fire)
caused by returning false for the cooresponding finger on the touchscreen.
Signed-off-by: Hansem Ro <hansemro@outlook.com>
Fixes: e3559442afd2a ("ili210x - rework the touchscreen sample processing")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The ILI251x seems to report pressure information in the 5th byte of
each per-finger touch data element. On the available hardware, this
information has the values ranging from 0x0 to 0xa, which is also
matching the downstream example code. Report pressure information
on the ILI251x.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20201224071238.160098-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This adds support for the Ilitek ili2120 touchscreen found in the
Fairphone 2 smartphone.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20200209151904.661210-1-luca@z3ntu.xyz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The is_visible function expects the permissions associated with an
attribute of the sysfs group or 0 if an attribute is not visible.
Change the code to return the attribute permissions when the attribute
should be visible which resolves the warning:
Attribute calibrate: Invalid permissions 01
Fixes: cc12ba1872c6 ("Input: ili210x - optionally show calibrate sysfs attribute")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20200209145628.649409-1-luca@z3ntu.xyz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Only show the 'calibrate' sysfs attribute on chip flavours
which support calibration by writing to a calibration register.
Do this by adding a flag to the chip operations structure.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191112210148.3535-2-TheSven73@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Optionally allow the touch screen resolution to be set by adding
it to the chip operations structure. If it is omitted (left zero),
the resolution defaults to 64K. Which is the previously hard-coded
value.
Set the ili2117 resolution to 2048, as indicated in its datasheet.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191112210148.3535-1-TheSven73@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The driver's method to retrieve the firmware version on ili2117/
ili2118 chip flavours is incorrect. The firmware version register
address and layout are wrong.
The firmware version is not actually used anywhere inside or
outside this driver. There is a dev_dbg() print, but that is
only visible when the developer explicitly compiles in debug
support.
Don't make the code more complicated to preserve a feature that
no-one is using. Remove all code associated with chip firmware
version.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191112164429.11225-1-TheSven73@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When I2C client is instantiated with I2C_CLIENT_WAKE flag (either via
"wakeup-source" device property, or via board info flag), it will mark the
main IRQ line as wakeup IRQ, which will ensure that it will be enabled for
wakeup when system transitions to suspend state. Since our suspend/resume
handlers were only managing IRQ wakeup state, they are no longer needed,
and can be removed.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
I2C devices that are supposed to be wakeup sources should be instantiated
with I2C_CLIENT_WAKE flag (which can be either set by in board info, or
retrieved from "wakeup-source" property); individual drivers should not be
marking devices as wakeup sources unconditionally.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Instead of doing if/else if/else on the chip's model number let's define
chip operations structure and use it to perform indirect calls. With number
of protocols supported by the driver growing, this makes it better
maintainable.
This change includes fixes to checks whether the driver should continue
polling the controller by Sven Van Asbroeck <thesven73@gmail.com>.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We are using devm_input_allocate_device() that set's up the parent for
us, no need to do it ourselves.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
input_mt_init_slots() may fail and we need to handle such failures.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Let's switch the driver to using threaded IRQ so that we do not need to
manage the interrupt and work separately, and we do not acknowledge
interrupt until we finished handling it completely.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Tested-by: Marek Vasut <marex@denx.de> # ILI2117
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add support for ILI2117 touch controller. This controller is similar
to the ILI210x and ILI251x, except for the following differences:
- Reading out of touch data must happen at most 300 mS after the
interrupt line was asserted. No command must be sent, the data
are returned upon pure I2C read of 43 bytes long.
- Supports 10 simultaneous touch inputs.
- Touch data format is slightly different.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org> # for DT binding
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fetching the geometry from the ILI251x registers seems unreliable and
sometimes returns all zeroes. Add support for fetching the geometry and
axis inversion from DT instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
By switching to devm_device_add_group() we can complete driver conversion
to using managed resources and get rid of ili210x_i2c_remove().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add support for ILI251x touch controller. This controller is similar
to the ILI210x, except for the following differences:
- Does not support I2C R-W transfer, Read must be followed by an
obscenely long delay, and then followed by Write
- Does support 10 simultaneous touch inputs.
- Touch data format is slightly different, pressure reporting does not
work although the touch data contain such information.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add OF match table for the ili210x touchscreen.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Perform the register access only after the I2C client data are set,
this is only done in preparation for the subsequent patch which
uses the I2C client data in the register IO function.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Get rid of the packed structures for representing data as that does not
apply to other similar Ilitek touchscreens. Instead, implement a function
which parses the data and reports touch events and coordinates.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Convert the driver to devm_request_irq(), drop the related unmanaged
deregistration code and add ili210x_irq_teardown() to tear the IRQ
down and cancel possible touchscreen pending work.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The touchscreen can have a reset GPIO connected to it, add support
for such an arrangement.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Convert the driver to dev-managed allocations.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The .get_pendown_state callback is set only by the platform data code,
which was just removed. Thus, get_pendown_state() always returns false,
so drop that altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
There is not a single user of the ili210x platform data in the kernel,
just drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Since there is no call to dev_get_drvdata() or input_get_drvdata(),
the call to input_set_drvdata() is unnecessary and can be dropped.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
If a function declares a variable to access a structure element,
use it consistently.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
"calibrate" attribute does not provide "show" methods and thus we should
not mark it as readable.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov:
"Drivers, drivers, drivers... No interesting input core changes this
time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (74 commits)
Input: elan_i2c - use iap_version to get firmware information
Input: max8997_haptic - fix module alias
Input: elan_i2c - fix typos for validpage_count
Input: psmouse - add small delay for IBM trackpoint pass-through mode
Input: synaptics - fix handling of disabling gesture mode
Input: elan_i2c - enable ELAN0100 acpi panels
Input: gpio-keys - report error when disabling unsupported key
Input: sur40 - fix error return code
Input: sentelic - silence some underflow warnings
Input: zhenhua - switch to using bitrev8()
Input: cros_ec_keyb - replace KEYBOARD_CROS_EC dependency
Input: cap11xx - add LED support
Input: elants_i2c - fix for devm_gpiod_get API change
Input: elan_i2c - enable asynchronous probing
Input: elants_i2c - enable asynchronous probing
Input: elants_i2c - wire up regulator support
Input: do not emit unneeded EV_SYN when suspending
Input: elants_i2c - disable idle mode before updating firmware
MAINTAINERS: Add maintainer for atmel_mxt_ts
Input: atmel_mxt_ts - remove warning on zero T44 count
...
|
|
This patch fix spelling typo inv various part of sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Use __maybe_unused instead of ifdef guards around suspend/resume
functions, in order to increase build coverage and fix build warnings.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Use the wrapper function for retrieving the platform data instead
of accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Preparing to move more repeated code into the mt core, add a flags
argument to the input_mt_slots_init() function.
Reviewed-and-tested-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Tested-by: Ping Cheng <pingc@wacom.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
|
|
The driver supports chipsets ILI2102, ILI2102s, ILI2103, ILI2103s and
ILI2105. Such kind of controllers can be found in Amazon Kindle Fire
devices.
Reviewed-by: Jan Paesmans <jan.paesmans@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
