| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit f78ca48a8ba9cdec96e8839351e49eec3233b177 upstream.
Currently we set SMBHSTCNT_LAST_BYTE only after the host has started
receiving the last byte. If we get e.g. preempted before setting
SMBHSTCNT_LAST_BYTE, the host may be finished with receiving the byte
before SMBHSTCNT_LAST_BYTE is set.
Therefore change the code to set SMBHSTCNT_LAST_BYTE before writing
SMBHSTSTS_BYTE_DONE for the byte before the last byte. Now the code
is also consistent with what we do in i801_isr_byte_done().
Reported-by: Jean Delvare <jdelvare@suse.com>
Closes: https://lore.kernel.org/linux-i2c/20230828152747.09444625@endymion.delvare/
Cc: stable@vger.kernel.org
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8183fa10c25c7b3c20670bf2b430ddcc1ee03c0 upstream.
During SMBus block data read process, we have seen high interrupt rate
because of TX_EMPTY irq status while waiting for block length byte (the
first data byte after the address phase). The interrupt handler does not
do anything because the internal state is kept as STATUS_WRITE_IN_PROGRESS.
Hence, we should disable TX_EMPTY IRQ until I2C DesignWare receives
first data byte from I2C device, then re-enable it to resume SMBus
transaction.
It takes 0.789 ms for host to receive data length from slave.
Without the patch, i2c_dw_isr() is called 99 times by TX_EMPTY interrupt.
And it is none after applying the patch.
Cc: stable@vger.kernel.org
Co-developed-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Chuong Tran <chuong@os.amperecomputing.com>
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b211c7671212cad0b83603c674838c7e824d845 upstream.
This reverts commit 0b01392c18b9993a584f36ace1d61118772ad0ca.
Conversion of PXA to generic I2C recovery, makes the I2C bus completely
lock up if recovery pinctrl is present in the DT and I2C recovery is
enabled.
So, until the generic I2C recovery can also work with PXA lets revert
to have working I2C and I2C recovery again.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: stable@vger.kernel.org # 5.11+
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa49c90894d06e18a1ee7c095edbd2f37c232d02 upstream.
Since bae1d3a05a8b, i2c transfers are non-atomic if preemption is
disabled. However, non-atomic i2c transfers require preemption (e.g. in
wait_for_completion() while waiting for the DMA).
panic() calls preempt_disable_notrace() before calling
emergency_restart(). Therefore, if an i2c device is used for the
restart, the xfer should be atomic. This avoids warnings like:
[ 12.667612] WARNING: CPU: 1 PID: 1 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch+0x33c/0x6b0
[ 12.676926] Voluntary context switch within RCU read-side critical section!
...
[ 12.742376] schedule_timeout from wait_for_completion_timeout+0x90/0x114
[ 12.749179] wait_for_completion_timeout from tegra_i2c_wait_completion+0x40/0x70
...
[ 12.994527] atomic_notifier_call_chain from machine_restart+0x34/0x58
[ 13.001050] machine_restart from panic+0x2a8/0x32c
Use !preemptible() instead, which is basically the same check as
pre-v5.2.
Fixes: bae1d3a05a8b ("i2c: core: remove use of in_atomic()")
Cc: stable@vger.kernel.org # v5.2+
Suggested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Link: https://lore.kernel.org/r/20230327-tegra-pmic-reboot-v7-2-18699d5dcd76@skidata.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cc9c54232f04aef3a5d7f64a0ece7df00f1aaa3d ]
i2c-dev.c utilizes memdup_user() to copy a userspace array. This is done
without an overflow check.
Use the new wrapper memdup_array_user() to copy the array more safely.
Suggested-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5ac61d26b8baff5b2e5a9f3dc1ef63297e4b53e7 ]
Make sure we don't OOPS in case clock-frequency is set to 0 in a DT. The
variable set here is later used as a divisor.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6af79f7fe748fe6a3c5c3a63d7f35981a82c2769 ]
Yang Yingliang reported a memleak:
===
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff888014aec078 (size 8):
comm "xrun", pid 356, jiffies 4294910619 (age 16.332s)
hex dump (first 8 bytes):
31 2d 30 30 31 63 00 00 1-001c..
backtrace:
[<00000000eb56c0a9>] __kmalloc_track_caller+0x1a6/0x300
[<000000000b220ea3>] kvasprintf+0xad/0x140
[<00000000b83203e5>] kvasprintf_const+0x62/0x190
[<000000002a5eab37>] kobject_set_name_vargs+0x56/0x140
[<00000000300ac279>] dev_set_name+0xb0/0xe0
[<00000000b66ebd6f>] i2c_new_client_device+0x7e4/0x9a0
If device_register() returns error in i2c_new_client_device(),
the name allocated by i2c_dev_set_name() need be freed. As
comment of device_register() says, it should use put_device()
to give up the reference in the error path.
===
I think this solution is less intrusive and more robust than he
originally proposed solutions, though.
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Closes: http://patchwork.ozlabs.org/project/linux-i2c/patch/20221124085448.3620240-1-yangyingliang@huawei.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ba15a14399c262f91ce30c19fcbdc952262dd1be ]
Add the code to handle an invalid state when both bits S_RX_EVENT
(indicating a transaction) and S_START_BUSY (indicating the end
of transaction - transition of START_BUSY from 1 to 0) are set in
the interrupt status register during a slave read.
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
Fixes: 1ca1b4516088 ("i2c: iproc: handle Master aborted error")
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 54f1840ddee9bbdc8dd89fbbfdfa632401244146 upstream.
When the `CONFIG_I2C_SLAVE` option is enabled and the device operates
as a slave, a situation arises where the master sends a START signal
without the accompanying STOP signal. This action results in a
persistent I2C bus timeout. The core issue stems from the fact that
the i2c controller remains in a slave read state without a timeout
mechanism. As a consequence, the bus perpetually experiences timeouts.
In this case, the i2c bus will be reset, but the slave_state reset is
missing.
Fixes: fee465150b45 ("i2c: aspeed: Reset the i2c controller when timeout occurs")
Signed-off-by: Jian Zhang <zhangjian.3032@bytedance.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c896ff2dd8f30a6b0a922c83a96f6d43f05f0e92 upstream.
In case of SMBUS byte read with PEC enabled, the whole transfer
is split into two commands. A first write command, followed by
a read command. The write command does not have any PEC byte
and a PEC byte is appended at the end of the read command.
(cf Read byte protocol with PEC in SMBUS specification)
Within the STM32 I2C controller, handling (either sending
or receiving) of the PEC byte is done via the PECBYTE bit in
register CR2.
Currently, the PECBYTE is set at the beginning of a transfer,
which lead to sending a PEC byte at the end of the write command
(hence losing the real last byte), and also does not check the
PEC byte received during the read command.
This patch corrects the function stm32f7_i2c_smbus_xfer_msg
in order to only set the PECBYTE during the read command.
Fixes: 9e48155f6bfe ("i2c: i2c-stm32f7: Add initial SMBus protocols support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0fb118de5003028ad092a4e66fc6d07b86c3bc94 upstream.
i2c-demux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: 50a5ba876908 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3dc0ec46f6e7511fc4fdf6b6cda439382bc957f1 upstream.
i2c-mux-gpmux uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: ac8498f0ce53 ("i2c: i2c-mux-gpmux: new driver")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3171d37b58a76e1febbf3f4af2d06234a98cf88b upstream.
i2c-mux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: c4aee3e1b0de ("i2c: mux: pinctrl: remove platform_data")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b13e59e74ff71a1004e0508107e91e9a84fd7388 ]
I2C_CLASS_DEPRECATED is a flag and not an actual class.
There's nothing speaking against both, parent and child, having
I2C_CLASS_DEPRECATED set. Therefore exclude it from the check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 3914784553f68c931fc666dbe7e86fe881aada38 upstream.
We have to unregister tco_pdev also if i2c_add_adapter() fails.
Fixes: 9424693035a5 ("i2c: i801: Create iTCO device on newer Intel PCHs")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 92e73d807b68b2214fcafca4e130b5300a9d4b3c ]
Sometimes, our completions race with new master transfers and override
the bus->operation and bus->master_or_slave variables. This causes
transactions to timeout and kernel crashes less frequently.
To remedy this, we re-order all completions to the very end of the
function.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: William A. Kennington III <william@wkennington.com>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 59851fb05d759f13662be143eff0aae605815b0e ]
The error paths for xiic_reinit() return negative values on failure
and 0 on success - this error message therefore is triggered on
_success_ rather than failure. Correct the condition so it's only
shown on failure as intended.
Fixes: 8fa9c9388053 ("i2c: xiic: return value of xiic_reinit")
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit db6aee6083a56ac4a6cd1b08fff7938072bcd0a3 ]
In i2c_mux_gpio_probe_fw(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 98b2b712bc85 ("i2c: i2c-mux-gpio: Enable this driver in ACPI land")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7c0195fa9a9e263df204963f88a22b21688ffb66 ]
devm_kstrdup() returns pointer to allocated string on success,
NULL on failure. So it is better to check the return value of it.
Fixes: e35478eac030 ("i2c: mux: demux-pinctrl: run properly with multiple instances")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit fee465150b458351b6d9b9f66084f3cc3022b88b upstream.
Reset the i2c controller when an i2c transfer timeout occurs.
The remaining interrupts and device should be reset to avoid
unpredictable controller behavior.
Fixes: 2e57b7cebb98 ("i2c: aspeed: Add multi-master use case support")
Cc: <stable@vger.kernel.org> # v5.1+
Signed-off-by: Tommy Huang <tommy_huang@aspeedtech.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1a50d9403fb90cbe4dea0ec9fd0351d2ecbd8924 upstream.
When loading a DT overlay that creates a device, the device is not
probed, unless the DT overlay is unloaded and reloaded again.
After the recent refactoring to improve fw_devlink, it no longer depends
on the "compatible" property to identify which device tree nodes will
become struct devices. fw_devlink now picks up dangling consumers
(consumers pointing to descendent device tree nodes of a device that
aren't converted to child devices) when a device is successfully bound
to a driver. See __fw_devlink_pickup_dangling_consumers().
However, during DT overlay, a device's device tree node can have
sub-nodes added/removed without unbinding/rebinding the driver. This
difference in behavior between the normal device instantiation and
probing flow vs. the DT overlay flow has a bunch of implications that
are pointed out elsewhere[1]. One of them is that the fw_devlink logic
to pick up dangling consumers is never exercised.
This patch solves the fw_devlink issue by marking all DT nodes added by
DT overlays with FWNODE_FLAG_NOT_DEVICE (fwnode that won't become
device), and by clearing the flag when a struct device is actually
created for the DT node. This way, fw_devlink knows not to have
consumers waiting on these newly added DT nodes, and to propagate the
dependency to an ancestor DT node that has the corresponding struct
device.
Based on a patch by Saravana Kannan, which covered only platform and spi
devices.
[1] https://lore.kernel.org/r/CAGETcx_bkuFaLCiPrAWCPQz+w79ccDp6=9e881qmK=vx3hBMyg@mail.gmail.com
Fixes: 4a032827daa89350 ("of: property: Simplify of_link_to_phandle()")
Link: https://lore.kernel.org/r/CAGETcx_+rhHvaC_HJXGrr5_WAd2+k5f=rWYnkCZ6z5bGX-wj4w@mail.gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Link: https://lore.kernel.org/r/e1fa546682ea4c8474ff997ab6244c5e11b6f8bc.1680182615.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 69f035c480d76f12bf061148ccfd578e1099e5fc upstream.
In the I2C_FUNC_SMBUS_BLOCK_DATA case, the invalid length byte value
(outside of 1-32) of the SMBus block data response from the Slave device
is not correctly handled by the I2C Designware driver.
In case IC_EMPTYFIFO_HOLD_MASTER_EN==1, which cannot be detected
from the registers, the Master can be disabled only if the STOP bit
is set. Without STOP bit set, the Master remains active, holding the bus
until receiving a block data response length. This hangs the bus and
is unrecoverable.
Avoid this by issuing another dump read to reach the stop condition when
an invalid length byte is received.
Cc: stable@vger.kernel.org
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230726080001.337353-3-tamnguyenchi@os.amperecomputing.com
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49d4db3953cb9004ff94efc0c176e026c820af5a upstream.
Commit 0daede80f870 ("i2c: designware: Convert driver to using regmap API")
changes the logic to validate the whole 32-bit return value of
DW_IC_DATA_CMD register instead of 8-bit LSB without reason.
Later, commit f53f15ba5a85 ("i2c: designware: Get right data length"),
introduced partial fix but not enough because the "tmp > 0" still test
tmp as 32-bit value and is wrong in case the IC_DATA_CMD[11] is set.
Revert the logic to just before commit 0daede80f870
("i2c: designware: Convert driver to using regmap API").
Fixes: f53f15ba5a85 ("i2c: designware: Get right data length")
Fixes: 0daede80f870 ("i2c: designware: Convert driver to using regmap API")
Cc: stable@vger.kernel.org
Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com>
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230726080001.337353-2-tamnguyenchi@os.amperecomputing.com
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 27ec43c77b5db780a56fc3a6d6de6bf2f74614f7 upstream.
Tegra processors prior to Tegra186 used APB DMA for I2C requiring
CONFIG_TEGRA20_APB_DMA=y while Tegra186 and later use GPC DMA requiring
CONFIG_TEGRA186_GPC_DMA=y.
The check for if the processor uses APB DMA is inverted and so the wrong
DMA config options are checked.
This means if CONFIG_TEGRA20_APB_DMA=y but CONFIG_TEGRA186_GPC_DMA=n
with a Tegra186 or later processor the driver will incorrectly think DMA is
enabled and attempt to request DMA channels that will never be availible,
leaving the driver in a perpetual EPROBE_DEFER state.
Fixes: 48cb6356fae1 ("i2c: tegra: Add GPCDMA support")
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Akhil R <akhilrajeev@nvidia.com>
Link: https://lore.kernel.org/r/fcfcf9b3-c8c4-9b34-2ff8-cd60a3d490bd@connecttech.com
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fff67c1b17ee093947bdcbac6f64d072e644159a upstream.
The controller may be shared with other port, for example the firmware.
Handle the interrupt from other sources will cause crash since some
data are not initialized. So only handle the interrupt of the driver's
transfer and discard others.
Fixes: d62fbdb99a85 ("i2c: add support for HiSilicon I2C controller")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230801124625.63587-1-yangyicong@huawei.com
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4caf4cb1eaed469742ef719f2cc024b1ec3fa9e6 upstream.
iproc_i2c_rd_reg() and iproc_i2c_wr_reg() are called from both
interrupt context (e.g. bcm_iproc_i2c_isr) and process context
(e.g. bcm_iproc_i2c_suspend). Therefore, interrupts should be
disabled to avoid potential deadlock. To prevent this scenario,
use spin_lock_irqsave().
Fixes: 9a1038728037 ("i2c: iproc: add NIC I2C support")
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 05f933d5f7318b03ff2028c1704dc867ac16f2c7 ]
Since commit 235602146ec9 ("i2c-nomadik: turn the platform driver to an amba
driver"), there is no more request_mem_region() call in this driver.
So remove the release_mem_region() call from the remove function which is
likely a left over.
Fixes: 235602146ec9 ("i2c-nomadik: turn the platform driver to an amba driver")
Cc: <stable@vger.kernel.org> # v3.6+
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9c7174db4cdd111e10d19eed5c36fd978a14c8a2 ]
Replace the pair of functions, devm_clk_get() and
clk_prepare_enable(), with a single function
devm_clk_get_enabled().
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 05f933d5f731 ("i2c: nomadik: Remove a useless call in the remove function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1c5d33fff0d375e4ab7c4261dc62a286babbb4c6 ]
The err_no_mem goto label doesn't do anything. Remove it.
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 05f933d5f731 ("i2c: nomadik: Remove a useless call in the remove function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 06e989578232da33a7fe96b04191b862af8b2cec ]
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding
size determination a bit safer according to the Linux coding style
convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 05f933d5f731 ("i2c: nomadik: Remove a useless call in the remove function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6b3b21a8542fd2fb6ffc61bc13b9419f0c58ebad ]
These issues were detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 05f933d5f731 ("i2c: nomadik: Remove a useless call in the remove function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a7fbfd44c0204f0629288edfd0d77829edb4a2f8 upstream.
power_supply_is_system_supplied() checks whether any power
supplies are present that aren't batteries to decide whether
the system is running on DC or AC. Downstream drivers use
this to make performance decisions.
Navi dGPUs include an UCSI function that has been exported
since commit 17631e8ca2d3 ("i2c: designware: Add driver
support for AMD NAVI GPU").
This UCSI function registers a power supply since commit
992a60ed0d5e ("usb: typec: ucsi: register with power_supply class")
but this is not a system power supply.
As the power supply for a dGPU is only for powering devices connected
to dGPU, create a device property to indicate that the UCSI endpoint
is only for the scope of `POWER_SUPPLY_SCOPE_DEVICE`.
Link: https://lore.kernel.org/lkml/20230516182541.5836-2-mario.limonciello@amd.com/
Reviewed-by: Evan Quan <evan.quan@amd.com>
Tested-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 430b38764fbb931c6dbd1af13c8b2e4508994662 upstream.
Now the Cypress CCG driver has been updated to support the
'firmware-name' property to align with device-tree, remove the
'ccgx,firmware-build' property as this is no longer needed.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20230131175748.256423-5-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f510b0a3565b9231e828e23a7e0f9790b97edf96 upstream.
Device-tree uses the 'firmware-name' string property to pass a name of
the firmware build to the Cypress CCGx driver. Add a new ACPI string
property to the NVIDIA GPU I2C driver to align with device-tree so that
we can migrate to using a common property name for both ACPI and
device-tree.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Co-developed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20230131175748.256423-3-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cd9489623c29aa2f8cc07088168afb6e0d5ef06d upstream.
Smatch Warns:
drivers/i2c/busses/i2c-qup.c:1784 qup_i2c_probe()
warn: missing unwind goto?
The goto label "fail_runtime" and "fail" will disable qup->pclk,
but here qup->pclk failed to obtain, in order to be consistent,
change the direct return to goto label "fail_dma".
Fixes: 9cedf3b2f099 ("i2c: qup: Add bam dma capabilities")
Signed-off-by: Shuai Jiang <d202180596@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cb6e45c9a0ad9e0f8664fd06db0227d185dc76ab ]
In xiic_process, it is possible that error events such as arbitration
lost or TX error can be raised in conjunction with other interrupt flags
such as TX FIFO empty or bus not busy. Error events result in the
controller being reset and the error returned to the calling request,
but the function could potentially try to keep handling the other
events, such as by writing more messages into the TX FIFO. Since the
transaction has already failed, this is not helpful and will just cause
issues.
This problem has been present ever since:
commit 7f9906bd7f72 ("i2c: xiic: Service all interrupts in isr")
which allowed non-error events to be handled after errors, but became
more obvious after:
commit 743e227a8959 ("i2c: xiic: Defer xiic_wakeup() and
__xiic_start_xfer() in xiic_process()")
which reworked the code to add a WARN_ON which triggers if both the
xfer_more and wakeup_req flags were set, since this combination is
not supposed to happen, but was occurring in this scenario.
Skip further interrupt handling after error flags are detected to avoid
this problem.
Fixes: 7f9906bd7f72 ("i2c: xiic: Service all interrupts in isr")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e69b9bc170c6d93ee375a5cbfd15f74c0fb59bdd ]
Claim clkhi and clklo as integer type to avoid possible calculation
errors caused by data overflow.
Fixes: a55fa9d0e42e ("i2c: imx-lpi2c: add low power i2c bus driver")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7ebfd881abe9e0ea9557b29dab6aa28d294fabb4 ]
Rather than casting pci1xxxx_i2c_shutdown to an incompatible function type,
update the type to match that expected by __devm_add_action.
Reported by clang-16 with W-1:
.../i2c-mchp-pci1xxxx.c:1159:29: error: cast from 'void (*)(struct pci1xxxx_i2c *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
ret = devm_add_action(dev, (void (*)(void *))pci1xxxx_i2c_shutdown, i2c);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/device.h:251:29: note: expanded from macro 'devm_add_action'
__devm_add_action(release, action, data, #action)
^~~~~~
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Tharun Kumar P<tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ca0aa17f2db3468fd017038d23a78e17388e2f67 ]
If pm runtime resume fails the .remove callback used to exit early. This
resulted in an error message by the driver core but the device gets
removed anyhow. This lets the registered i2c adapter stay around with an
unbound parent device.
So only skip clk disabling if resume failed, but do delete the adapter.
Fixes: 8b9ec0719834 ("i2c: Add Spreadtrum I2C controller driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5578d0a79b6430fa1543640dd6f2d397d0886ce7 ]
There seems to be a bug within the mv64xxx I2C controller, wherein the
status register may not necessarily contain valid value immediately
after the IFLG flag is set in the control register.
My theory is that the controller:
- first sets the IFLG in control register
- then updates the status register
- then raises an interrupt
This may sometime cause weird bugs when in atomic mode, since in this
mode we do not wait for an interrupt, but instead we poll the control
register for IFLG and read status register immediately after.
I encountered -ENXIO from mv64xxx_i2c_fsm() due to this issue when using
this driver in atomic mode.
Note that I've only seen this issue on Armada 385, I don't know whether
other SOCs with this controller are also affected. Also note that this
fix has been in U-Boot for over 4 years [1] without anybody complaining,
so it should not cause regressions.
[1] https://source.denx.de/u-boot/u-boot/-/commit/d50e29662f78
Fixes: 544a8d75f3d6 ("i2c: mv64xxx: Add atomic_xfer method to driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9f855779a3874eee70e9f6be57b5f7774f14e510 ]
Update the msg->len value correctly for SMBUS block read. The discrepancy
went unnoticed as msg->len is used in SMBUS transfers only when a PEC
byte is added.
Fixes: d7583c8a5748 ("i2c: tegra: Add SMBus block read function")
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d663d93bb47e7ab45602b227701022d8aa16040a ]
The xiic_xfer() function gets a runtime PM reference when the function is
entered. This reference is released when the function is exited. There is
currently one error path where the function exits directly, which leads to
a leak of the runtime PM reference.
Make sure that this error path also releases the runtime PM reference.
Fixes: fdacc3c7405d ("i2c: xiic: Switch from waitqueue to completion")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ae1664f04f504a998737f5bb563f16b44357bcca ]
The cdns_i2c_master_xfer() function gets a runtime PM reference when the
function is entered. This reference is released when the function is
exited. There is currently one error path where the function exits
directly, which leads to a leak of the runtime PM reference.
Make sure that this error path also releases the runtime PM reference.
Fixes: 1a351b10b967 ("i2c: cadence: Added slave support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c770657bd2611b077ec1e7b1fe6aa92f249399bd upstream.
Using standard mode, rare false ACK responses were appearing with
i2cdetect tool. This was happening due to NACK interrupt triggering
ISR thread before register access interrupt was ready. Removing the
NACK interrupt's ability to trigger ISR thread lets register access
ready interrupt do this instead.
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 3b2f8f82dad7 ("i2c: omap: switch to threaded IRQ support")
Signed-off-by: Reid Tonking <reidt@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f8160d3b35fc94491bb0cb974dbda310ef96c0e2 ]
In polling mode, no stop condition is generated after a timeout. This
causes SCL to remain low and thereby block the bus. If this happens
during a transfer it can cause slaves to misinterpret the subsequent
transfer and return wrong values.
To solve this, pass the ETIMEDOUT error up from ocores_process_polling()
instead of setting STATE_ERROR directly. The caller is adjusted to call
ocores_process_timeout() on error both in polling and in IRQ mode, which
will set STATE_ERROR and generate a stop condition.
Fixes: 69c8c0c0efa8 ("i2c: ocores: add polling interface")
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aa874cdfec07d4dd9c6f0c356d65c609ba31a26f ]
Update I2C timing registers based on latest hardware design.
This fix does not break functionality of chips with older design and
existing users will not be affected.
Fixes: 361693697249 ("i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch")
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cc9812a3096d1986caca9a23bee99effc45c08df ]
After issuing all the messages we can disable the TX_EMPTY interrupts
to avoid handling redundant interrupts. For doing a sinlge bus
detection (i2cdetect -y -r 0) we can reduce ~97% interrupts (before
~12000 after ~400).
Signed-off-by: Sheng Feng <fengsheng5@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 987dd36c0141f6ab9f0fbf14d6b2ec3342dedb2f ]
When start sending a new message clear the Rx & Tx buffer pointers in
order to avoid using stale pointers.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 92fbb6d1296f81f41f65effd7f5f8c0f74943d15 upstream.
The data->block[0] variable comes from user and is a number between
0-255. Without proper check, the variable may be very large to cause
an out-of-bounds when performing memcpy in slimpro_i2c_blkwr.
Fix this bug by checking the value of writelen.
Fixes: f6505fbabc42 ("i2c: add SLIMpro I2C device driver on APM X-Gene platform")
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d98263512684a47e81bcb72a5408958ecd1e60b0 ]
The controller will always generate a completion interrupt when the
transfer is finished normally or not. Currently we use either error or
completion interrupt to finish, this may result the completion
interrupt unhandled and corrupt the next transfer, especially at low
speed mode. Since on error case, the error interrupt will come first
then is the completion interrupt. So only use the completion interrupt
to finish the whole transfer process.
Fixes: d62fbdb99a85 ("i2c: add support for HiSilicon I2C controller")
Reported-by: Sheng Feng <fengsheng5@huawei.com>
Signed-off-by: Sheng Feng <fengsheng5@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
