| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Use loops for reading temp_max and initialising FAN_MIN/TEMP_MAX rather
than duplicating code.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200924085102.15219-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Zen3 thermal info is supported via a new PCI device ID. Also the voltage
telemetry registers and the current factors need to be defined. k10temp
driver then searches for CPU family 0x19 and configures k10temp_data
accordingly.
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Link: https://lore.kernel.org/r/20200914200715.1997757-1-wei.huang2@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
0-day rightfully complains about a sometimes uninitialized variable
in pmbus_get_boolean().
drivers/hwmon/pmbus/pmbus_core.c:903:13: warning:
variable 'ret' is used uninitialized whenever 'if' condition is true
} else if (!s1 || !s2) {
While that is technically true, it won't be hit in the field since the
condition indicates a programming error. Move the check of that condition
into the code generating the attribute entry, and refuse generating the
attribute if the condition is true. Swap the condition check in
pmbus_get_boolean() to ensure that static analyzers don't get a hiccup
(because we check if s1 and s2 are NULL, static analyzers may believe
that they can be NULL independently of each other).
Reported-by: kernel test robot <lkp@intel.com>
Cc: Alex Qiu <xqiu@google.com>
Reviewed-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Enable runtime debug control of whether the PEC byte is exchanged with
the PMBus device.
Some manufacturers have asked for the PEC to be disabled as part of
debugging driver communication issues with devices.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20200910021106.2958382-1-andrew@aj.id.au
[groeck: Replace %1llu with %llu]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Caching register values can be very expensive for PMBus chips. Some
modern chips may have 10 or more pages, with several sensors supported
per page. For example, MAX16601 creates more than 90 sysfs attributes.
Register caching for such chips is time consuming, especially if only a
few attributes are read on a regular basis. For MAX16601, it was observed
that it can take up to two seconds to read all attributes on a slow I2C
bus. In this situation, register caching results in the opposite of its
intention: It increases the number of I2C operations, in some cases
substantially, and it results in large latency when trying to access
individual sensor data.
Drop all register caching to solve the problem. Since it is no longer
necessary, drop status register mapping as part of the change, and specify
status registers directly.
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alex Qiu <xqiu@google.com>
Tested-by: Alex Qiu <xqiu@google.com>
Link: https://lore.kernel.org/r/20200904163314.259087-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The debugfs code was intended to aid figuring out functionality
of undocumented registers. Turns out that wasn't very helpful,
since register locations change too much between AMD chip revisions,
and the data isn't really valuable for chips where it isn't already
supported. On top of that, its existence has been used as argument
for providing pseudo-API debugfs functions in other drivers.
So let's just take it out.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add a fan sensor to report RPM's from a fan tach input.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The voltage telemetry registers for Zen2 are different from Zen1. Also
the factors of CPU current values are changed on Zen2. Add new definitions
for these register.
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Link: https://lore.kernel.org/r/20200827054242.2347-2-wei.huang2@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Many SMN thermal registers in Zen CPU families are common across different
generations. For long-term code maintenance, it is better to rename these
macro and function names to Zen.
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Link: https://lore.kernel.org/r/20200827054242.2347-1-wei.huang2@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use semicolons and braces.
Signed-off-by: Joe Perches <joe@perches.com>
Link: https://lore.kernel.org/r/5e1ca60df261e3bfd0e6510e388581a1d1f52c77.1598331149.git.joe@perches.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use the nvmem kernel api to expose the black box
chip functionality to userspace.
Using this feature, the device is capable of recording
to nonvolatile flash memory the vital data about the
system status that caused the system to perform a
black box write.
A blackbox is 64 bytes of data containing all the
status registers, last two states of the sequencer,
timestamp and counters. The mapping of this data is
described in the adm1266 datasheet.
On power-up the driver sets the unix time to
the adm1266 using the SET_RTC command. This value
is incremented by an internal clock and it is used
as timestamp for the black box feature.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-6-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add a debugfs entry which prints the current state
of the adm1266 sequencer.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-5-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Adm1266 exposes 9 GPIOs and 16 PDIOs which are currently read-only. They
are controlled by the internal sequencing engine.
This patch makes adm1266 driver expose GPIOs and PDIOs to user-space
using GPIO provider kernel api.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-4-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
PmBus devices support Block Write-Block Read Process
Call described in SMBus specification v 2.0 with the
exception that Block writes and reads are permitted to
have up 255 data bytes instead of max 32 bytes (SMBus).
This patch adds Block WR process call support for ADM1266.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-3-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add pmbus probing driver for the adm1266 Cascadable
Super Sequencer with Margin Control and Fault Recording.
Driver is using the pmbus_core, creating sysfs files
under hwmon for inputs: vh1->vh4 and vp1->vp13.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-2-alexandru.tachici@analog.com
[groeck: Use .probe_new function, adjust for changed pmbus_do_probe API]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for DTS bindings for the sensirion shtc1,shtw1 and shtc3.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200815012227.32538-2-chris.ruehl@gtsys.com.hk
[groeck: Resolved conflicts]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1597649673-22329-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160035.590142-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160159.591293-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160231.592571-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Many hwmon drivers don't use the id information provided by the old
i2c probe function, and the remainder can easily be adapted to the new
form ("probe_new") by calling i2c_match_id explicitly.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified to call i2c_match_id() with the same level of
error-handling (if any) as before.
This patch wraps up the transition for hwmon, with four stragglers not
included in the previous large patch.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160354.594715-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162851.1519546-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162704.1517951-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162544.1516647-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162300.1514695-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162026.1512242-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813161845.1511261-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/20200813161129.1507599-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813160958.1506536-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Many hwmon drivers don't use the id information provided by the old
i2c probe function, and the remainder can easily be adapted to the new
form ("probe_new") by calling i2c_match_id explicitly.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
A few drivers aren't included in this patch because they have a
different set of maintainers. They will be covered by other patches.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813160222.1503401-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
pmbus_do_probe doesn't use the id information provided in its second
argument, so this can be removed, which then allows using the
single-parameter i2c probe function ("probe_new") for probes.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* configured v. probed comparisons are performed by comparing the
configured name to the detected name, instead of the ids; this
involves strcmp but is still cheaper than comparing all the device
names when scanning the tables;
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
Additionally, the mismatch message in the ltc2978 driver is adjusted
so that it no longer assumes that the driver_data is an index into
ltc2978_id.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200808210004.30880-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Adding implementation for new attributes (rated_min/rated_max) to
cover PMBus specification about rated values reporting:
MFR_VIN_MIN, MFR_VIN_MAX, MFR_IIN_MAX, MFR_PIN_MAX, MFR_VOUT_MIN,
MFR_VOUT_MAX, MFR_IOUT_MAX, MFR_POUT_MAX, MFR_MAX_TEMP_1/2/3.
Tested with OpenBMC stack. All rated attributes were available
and reported correct values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-4-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Adding implementation for new attributes (rated_min/rated_max) for
currentX, inX, powerX, tempX and humidityX.
Tested with OpenBMC stack and simple hwmon driver using
rated_min/rated_max for the following types of sensors: hwmon_temp,
hwmon_in, hwmon_curr, hwmon_power, hwmon_humidity.
For each sensor rated attributes were available and returned
expected values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-3-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Smatch has a new check for resource leaks which found a bug in probe:
drivers/hwmon/w83627ehf.c:2417 w83627ehf_probe()
warn: 'res->start' not released on lines: 2412.
We need to clean up if devm_hwmon_device_register_with_info() fails.
Fixes: 266cd5835947 ("hwmon: (w83627ehf) convert to with_info interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20200921125212.GA1128194@mwanda
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Starting with MAX34451, the chips of this series support STATUS_IOUT and
STATUS_TEMPERATURE commands, and no longer report over-current and
over-temperature status with STATUS_MFR_SPECIFIC.
Fixes: 7a001dbab4ade ("hwmon: (pmbus/max34440) Add support for MAX34451.")
Fixes: 50115ac9b6f35 ("hwmon: (pmbus/max34440) Add support for MAX34460 and MAX34461")
Reported-by: Steve Foreman <foremans@google.com>
Cc: Steve Foreman <foremans@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
If the temperature is read before the internal calibration is
completed, the driver returns -EIO. Instead it should return -EAGAIN
to encourage repeating the operation.
Note (groeck): Returning -EAGAIN to userspace may result in hard loops;
some userspace code interprets -EAGAIN as request to retry immediately.
I would prefer -ENODATA, but it turns out that the thermal subsystem only
handles -EAGAIN silently, so we'll have to stick with that.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200903134704.8949-1-lars.povlsen@microchip.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the hardware monitoring controller of the sl28cpld board
management controller. This driver is part of a multi-function device.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We need the driver core changes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Shrink pmbus code by using devm_hwmon_device_register_with_groups()
and devm_krealloc() instead of their non-managed variants.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200824173859.4910-3-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix tempeerature scale in gsc-hwmon driver
- Fix divide by 0 error in nct7904 driver
- Drop non-existing attribute from pmbus/isl68137 driver
- Fix status check in applesmc driver
* tag 'hwmon-for-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (gsc-hwmon) Scale temperature to millidegrees
hwmon: (applesmc) check status earlier.
hwmon: (nct7904) Correct divide by 0
hwmon: (pmbus/isl68137) remove READ_TEMPERATURE_1 telemetry for RAA228228
|
|
The GSC registers report temperature in decidegrees celcius so we
need to scale it to represent the hwmon sysfs API of millidegrees.
Cc: stable@vger.kernel.org
Fixes: 3bce5377ef66 ("hwmon: Add Gateworks System Controller support")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://lore.kernel.org/r/1598548824-16898-1-git-send-email-tharvey@gateworks.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
clang static analysis reports this representative problem
applesmc.c:758:10: warning: 1st function call argument is an
uninitialized value
left = be16_to_cpu(*(__be16 *)(buffer + 6)) >> 2;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
buffer is filled by the earlier call
ret = applesmc_read_key(LIGHT_SENSOR_LEFT_KEY, ...
This problem is reported because a goto skips the status check.
Other similar problems use data from applesmc_read_key before checking
the status. So move the checks to before the use.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Henrik Rydberg <rydberg@bitmath.org>
Link: https://lore.kernel.org/r/20200820131932.10590-1-trix@redhat.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
We hit a kernel panic due to a divide by 0 in nct7904_read_fan() for
the hwmon_fan_min case. Extend the check to hwmon_fan_input case as well
for safety.
[ 1656.545650] divide error: 0000 [#1] SMP PTI
[ 1656.545779] CPU: 12 PID: 18010 Comm: sensors Not tainted 5.4.47 #1
[ 1656.546065] RIP: 0010:nct7904_read+0x1e9/0x510 [nct7904]
...
[ 1656.546549] RAX: 0000000000149970 RBX: ffffbd6b86bcbe08 RCX: 0000000000000000
...
[ 1656.547548] Call Trace:
[ 1656.547665] hwmon_attr_show+0x32/0xd0 [hwmon]
[ 1656.547783] dev_attr_show+0x18/0x50
[ 1656.547898] sysfs_kf_seq_show+0x99/0x120
[ 1656.548013] seq_read+0xd8/0x3e0
[ 1656.548127] vfs_read+0x89/0x130
[ 1656.548234] ksys_read+0x7d/0xb0
[ 1656.548342] do_syscall_64+0x48/0x110
[ 1656.548451] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: d65a5102a99f5 ("hwmon: (nct7904) Convert to use new hwmon registration API")
Signed-off-by: Jason Baron <jbaron@akamai.com>
Link: https://lore.kernel.org/r/1598026814-2604-1-git-send-email-jbaron@akamai.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
There are multiple drivers using the private adc interface.
It seems unlikely that they would ever get converted to iio,
so make the current state official by making the header file
global.
The s3c2410_ts driver needs a couple of register definitions
as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-22-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Per the RAA228228 datasheet, READ_TEMPERATURE_1 is not a supported PMBus
command.
Signed-off-by: Grant Peltier <grantpeltier93@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some
types of hardware can generate the full range of signals that they're
capable of.
The remainder is mostly minor fixes and cleanups"
* tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: bcm-iproc: handle clk_get_rate() return
pwm: Replace HTTP links with HTTPS ones
pwm: omap-dmtimer: Repair pwm_omap_dmtimer_chip's broken kerneldoc header
pwm: mediatek: Provide missing kerneldoc description for 'soc' arg
pwm: bcm-kona: Remove impossible comparison when validating duty cycle
pwm: bcm-iproc: Remove impossible comparison when validating duty cycle
pwm: iqs620a: Use lowercase hexadecimal literals for consistency
pwm: Convert period and duty cycle to u64
clk: pwm: Use 64-bit division function
backlight: pwm_bl: Use 64-bit division function
pwm: sun4i: Use nsecs_to_jiffies to avoid a division
pwm: sifive: Use 64-bit division macro
pwm: iqs620a: Use 64-bit division
pwm: imx27: Use 64-bit division macro
pwm: imx-tpm: Use 64-bit division macro
pwm: clps711x: Use 64-bit division macro
hwmon: pwm-fan: Use 64-bit division macro
drm/i915: Use 64-bit division macro
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Highlights:
- New driver for Sparx5 SoC temperature sensot
- New driver for Corsair Commander Pro
- MAX20710 support added to max20730 driver
Enhancements:
- max6697: Allow max6581 to create tempX_offset attributes
- gsc (Gateworks System Controller): add 16bit pre-scaled voltage mode
- adm1275: Enable adm1278 ADM1278_TEMP1_EN
- dell-smm: Add Latitude 5480 to fan control whitelist
Fixes:
- adc128d818: Fix advanced configuration register init
- pmbus/core: Use s64 instead of long for calculations to fix
overflow issues with 32-bit architectures
Plus various cleanups in several drivers"
* tag 'hwmon-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (32 commits)
hwmon: (adc128d818) Fix advanced configuration register init
hwmon: (axi-fan-control) remove duplicate macros
hwmon: (i5k_amb, vt8231) Drop uses of pci_read_config_*() return value
hwmon: (sparx5) Make symbol 's5_temp_match' static
hwmon: (corsair-cpro) add reading pwm values
hwmon: sparx5: Add Sparx5 SoC temperature driver
dt-bindings: hwmon: Add Sparx5 temperature sensor
hwmon: (tmp401) Replace HTTP links with HTTPS ones
hwmon: (lm95234) Replace HTTP links with HTTPS ones
hwmon: (lm90) Replace HTTP links with HTTPS ones
hwmon: (k8temp) Replace HTTP links with HTTPS ones
hwmon: (jc42) Replace HTTP links with HTTPS ones
hwmon: (ina2xx) Replace HTTP links with HTTPS ones
hwmon: (ina209) Replace HTTP links with HTTPS ones
hwmon: Replace HTTP links with HTTPS ones
docs: hwmon: Replace HTTP links with HTTPS ones
hwmon: (adm1025) Replace HTTP links with HTTPS ones
hwmon: add Corsair Commander Pro driver
hwmon: (max6697) Allow max6581 to create tempX_offset
hwmon: (tmmp513) Replace HTTP links with HTTPS links
...
|
|
If the operation mode is non-zero and an external reference voltage is set,
first the operation mode is written to the advanced configuration register,
followed by the externel reference enable bit,
resetting the configuration mode to 0.
To fix this, first compose the value of the advanced configuration register
based on the configuration mode and the external reference voltage.
The advanced configuration register is then written to the device,
if it is different from the default register value (0x0).
Signed-off-by: Roy van Doormaal <roy.van.doormaal@prodrive-technologies.com>
Link: https://lore.kernel.org/r/20200728151846.231785-1-roy.van.doormaal@prodrive-technologies.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
