| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
All DPT FB color plane surface base addresses must be 2MB aligned. On
ADL_P this means that the offsets in CCS FB object must be also 2MB
aligned. Adjusting unaligned offsets for these FBs during commit time
(compensating with the x/y offsets) doesn't work, since the big
alignment would most probably lead to an x/y offset mismatch error
between the main and CCS planes.
We can overcome this limitation by remapping CCS FBs, so that each color
plane is at an aligned offset, leaving x/y for each plane unadjusted
during commit and so not causing an x/y mismatch error. However
remapping for CCS FBs will be done as a follow-up, so for now require
that user space allocates the FB obj with properly aligned planes.
v2: s/SZ_2M/512*4k/ for clarity. (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210524172703.2113058-1-imre.deak@intel.com
|
|
The driver currently disables the LTTPR non-transparent link training
mode for sinks with a DPCD_REV<1.4, based on the following description
of the LTTPR DPCD register range in DP standard 2.0 (at the 0xF0000
register description):
""
LTTPR-related registers at DPCD Addresses F0000h through F02FFh are valid
only for DPCD r1.4 (or higher).
"""
The transparent link training mode should still work fine, however the
implementation for this in some retimer FWs seems to be broken, see the
References: link below.
After discussions with DP standard authors the above "DPCD r1.4" does
not refer to the DPCD revision (stored in the DPCD_REV reg at 0x00000),
rather to the "LTTPR field data structure revision" stored in the
0xF0000 reg. An update request has been filed at vesa.org (see
wg/Link/documentComment/3746) for the upcoming v2.1 specification to
clarify the above description along the following lines:
"""
LTTPR-related registers at DPCD Addresses F0000h through F02FFh are
valid only for LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV 1.4 (or
higher)
"""
Based on my tests Windows uses the non-transparent link training mode
for DPCD_REV==1.2 sinks as well (so presumably for all DPCD_REVs), and
forcing it to use transparent mode on ICL/TGL platforms leads to the
same LT failure as reported at the References: link.
Based on the above let's assume that the transparent link training mode
is not well tested/supported and align the code to the correct
interpretation of what the r1.4 version refers to.
Reported-and-tested-by: Casey Harkins <caseyharkins@gmail.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
References: https://gitlab.freedesktop.org/drm/intel/-/issues/3415
Fixes: 264613b406eb ("drm/i915: Disable LTTPR support when the DPCD rev < 1.4")
Cc: <stable@vger.kernel.org> # v5.11+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512212809.1234701-1-imre.deak@intel.com
(cherry picked from commit cb4920cc40f630b5a247f4ed7d3dea66749df588)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/1621840854-105978-1-git-send-email-zou_wei@huawei.com
|
|
When main component is not probed, by example when the dw-hdmi module is
not loaded yet or in probe defer, the following crash appears on shutdown:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000038
...
pc : meson_drv_shutdown+0x24/0x50
lr : platform_drv_shutdown+0x20/0x30
...
Call trace:
meson_drv_shutdown+0x24/0x50
platform_drv_shutdown+0x20/0x30
device_shutdown+0x158/0x360
kernel_restart_prepare+0x38/0x48
kernel_restart+0x18/0x68
__do_sys_reboot+0x224/0x250
__arm64_sys_reboot+0x24/0x30
...
Simply check if the priv struct has been allocated before using it.
Fixes: fa0c16caf3d7 ("drm: meson_drv add shutdown function")
Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430082744.3638743-1-narmstrong@baylibre.com
|
|
Fix table returned when port_clock > 270000:
drivers/gpu/drm/i915/display/intel_ddi_buf_trans.c:752:47: error: variable 'adlp_dkl_phy_dp_ddi_trans_hbr2_hbr3' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
Initial version of the patch had it in a single table, but on second
version the table got split, but we continued to reference just one of
them.
Fixes: ca962882268a ("drm/i915/adl_p: Define and use ADL-P specific DP translation tables")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210521005209.4058702-1-lucas.demarchi@intel.com
|
|
The PM Runtime docs specifically call out the need to call
pm_runtime_dont_use_autosuspend() in the remove() callback if
pm_runtime_use_autosuspend() was called in probe():
> Drivers in ->remove() callback should undo the runtime PM changes done
> in ->probe(). Usually this means calling pm_runtime_disable(),
> pm_runtime_dont_use_autosuspend() etc.
We should do this. This fixes a warning splat that I saw when I was
testing out the panel-simple's remove().
Fixes: 3235b0f20a0a ("drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210517130450.v7.1.I9e947183e95c9bd067c9c1d51208ac6a96385139@changeid
|
|
It looks like some displays (like the LG 27UL850-W) don't enable the
scrambling when the HDMI driver enables it. However, if we set later the
scrambler enable bit, the display will work as expected.
Let's create delayed work queue to periodically look at the display
scrambling status, and if it's not set yet try to enable it again.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-12-maxime@cerno.tech
|
|
The HDMI controller on the BCM2711 includes a scrambler in order to
reach the HDMI 2.0 modes that require it. Let's add the support for it.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-11-maxime@cerno.tech
|
|
In order to reach the frequencies needed to output at 594MHz, the
firmware needs to be configured with the appropriate parameters in the
config.txt file (enable_hdmi_4kp60 and force_turbo).
Let's detect it at bind time, warn the user if we can't, and filter out
the relevant modes.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-10-maxime@cerno.tech
|
|
The BVB clock rate computation doesn't take into account a mode clock of
594MHz that we're going to need to support 4k60.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-9-maxime@cerno.tech
|
|
We'll need to have the HVS binding before the HDMI controllers so that
we can check whether the firmware allows to run in 4kp60. Reorder a bit
the component list, and document the current constraints we're aware of.
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-8-maxime@cerno.tech
|
|
Since we fixed the hooks to disable the encoder at boot, we now have an
unbalanced clk_disable call at boot since we never enabled them in the
first place.
Let's mimic the state of the hardware and enable the clocks at boot if
the controller is enabled to get the use-count right.
Cc: <stable@vger.kernel.org> # v5.10+
Fixes: 09c438139b8f ("drm/vc4: hdmi: Implement finer-grained hooks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-7-maxime@cerno.tech
|
|
At boot, we can't rely on the vc4_get_crtc_encoder since we don't have a
state yet and thus will not be able to figure out which connector is
attached to our CRTC.
However, we have a muxing bit in the CRTC register we can use to get the
encoder currently connected to the pixelvalve. We can thus read that
register, lookup the associated register through the vc4_pv_data
structure, and then pass it to vc4_crtc_disable so that we can perform
the proper operations.
Fixes: 875a4d536842 ("drm/vc4: drv: Disable the CRTC at boot time")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-6-maxime@cerno.tech
|
|
The vc4_get_crtc_encoder function currently only works when the
connector->state->crtc pointer is set, which is only true when the
connector is currently enabled.
However, we use it as part of the disable path as well, and our lookup
will fail in that case, resulting in it returning a null pointer we
can't act on.
We can access the connector that used to be connected to that crtc
though using the old connector state in the disable path.
Since we want to support both the enable and disable path, we can
support it by passing the state accessor variant as a function pointer,
together with the atomic state.
Fixes: 792c3132bc1b ("drm/vc4: encoder: Add finer-grained encoder callbacks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-5-maxime@cerno.tech
|
|
The vc4_crtc_config_pv will need to access the drm_atomic_state
structure and its only parent function, vc4_crtc_atomic_enable already
has access to it. Let's pass it as a parameter.
Fixes: 792c3132bc1b ("drm/vc4: encoder: Add finer-grained encoder callbacks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-4-maxime@cerno.tech
|
|
The vc4_set_crtc_possible_masks is meant to run over all the encoders
and then set their possible_crtcs mask to their associated pixelvalve.
However, since the commit 39fcb2808376 ("drm/vc4: txp: Turn the TXP into
a CRTC of its own"), the TXP has been turned to a CRTC and encoder of
its own, and while it does indeed register an encoder, it no longer has
an associated pixelvalve. The code will thus run over the TXP encoder
and set a bogus possible_crtcs mask, overriding the one set in the TXP
bind function.
In order to fix this, let's skip any virtual encoder.
Cc: <stable@vger.kernel.org> # v5.9+
Fixes: 39fcb2808376 ("drm/vc4: txp: Turn the TXP into a CRTC of its own")
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-3-maxime@cerno.tech
|
|
The current code does a binary OR on the possible_crtcs variable of the
TXP encoder, while we want to set it to that value instead.
Cc: <stable@vger.kernel.org> # v5.9+
Fixes: 39fcb2808376 ("drm/vc4: txp: Turn the TXP into a CRTC of its own")
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-2-maxime@cerno.tech
|
|
The VEC's DAC on BCM2711 is slightly different compared to the one on
BCM283x and needs different configuration. In particular, bit 3
(mask 0x8) switches the BCM2711 DAC input to "self-test input data",
which makes the output unusable. Separating two compatible variants in
devicetrees and the DRM driver was therefore necessary.
The configurations used for both variants have been borrowed from
Raspberry Pi (model 3B for BCM283x, 4B for BCM2711) firmware defaults.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210520150344.273900-4-maxime@cerno.tech
|
|
On the BCM2711 (Raspberry Pi 4), the VEC is actually connected to
output 2 of pixelvalve3.
NOTE: This contradicts the Broadcom docs, but has been empirically
tested and confirmed by Raspberry Pi firmware devs.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210520150344.273900-2-maxime@cerno.tech
|
|
Propogate changes to macros name containing CSR_*
to DMC_* from display side.
Fixes: 0633cdcbaa77 ("drm/i915/dmc: Rename macro names containing csr")
Cc: intel-gvt-dev@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210521174047.3861-1-anusha.srivatsa@intel.com
|
|
Backmerging from drm/drm-next to the patches for AMD devices
for v5.14.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210511091344.4508-1-thunder.leizhen@huawei.com
|
|
The dev_info():s in the DSI driver are very talkative,
depromote these to dev_dbg().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313230913.4108256-1-linus.walleij@linaro.org
|
|
The first parameter passed to container_of() is the pointer to the work
structure passed to the worker and never NULL. The NULL check on the
result of container_of() is therefore unnecessary and misleading.
Remove it.
This change was made automatically with the following Coccinelle script.
@@
type t;
identifier v;
statement s;
@@
<+...
(
t v = container_of(...);
|
v = container_of(...);
)
...
when != v
- if (\( !v \| v == NULL \) ) s
...+>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Eliminate the follow smatch warning:
drivers/gpu/drm/amd/amdgpu/sdma_v5_0.c:449
sdma_v5_0_ring_emit_mem_sync() warn: inconsistent indenting.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Try the handle from ATPX first since this is the most
common case.
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Treat it like ATIF and check both the dGPU and APU for
the method. This is required because ATCS may be hung
off of the APU in ACPI on A+A systems.
v2: add back accidently removed ACPI handle check.
v3: Fix incorrect atif check (Colin)
Fix uninitialized variable (Colin)
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Avoid spamming the log. The backlight controller on DCN chips
gets powered down when the display is off, so if you attempt to
set the backlight level when the display is off, you'll get this
message. This isn't a problem as we cache the requested backlight
level if it's adjusted when the display is off and set it again
during modeset.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: nicholas.choi@amd.com
Cc: harry.wentland@amd.com
|
|
[Why]
FS video support regressed GPU scaling and the scaled buffer ends up
stuck in the top left of the screen at native size - full, aspect,
center scaling modes do not function.
This is because decide_crtc_timing_for_drm_display_mode() does not
get called when scaling is enabled.
[How]
Split recalculate timing and scaling into two different flags.
We don't want to call drm_mode_set_crtcinfo() for scaling, but we
do want to call it for FS video.
Optimize and move preferred_refresh calculation next to
decide_crtc_timing_for_drm_display_mode() like it used to be since
that's not used for FS video.
We don't need to copy over the VIC or polarity in the case of FS video
modes because those don't change.
Fixes: 6f59f229f8ed7a ("drm/amd/display: Skip modeset for front porch change")
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
KFD userptr BOs and SG BOs used for DMA mappings can be preempted with
CWSR. Therefore we can use preemptible placement and avoid unwanted
evictions due to GTT accounting.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
SG BOs such as dmabuf imports and userptr BOs do not consume system
resources directly. Instead they point to resources owned elsewhere.
They typically get evicted by DMABuf move notifiers of MMU notifiers.
If those notifiers don't need to wait for hardware fences (i.e. the SG
BOs are used in a preemptible context), then we don't need to limit
them to the GTT size and we don't need TTM to evict them.
Create a new placement for such preemptible SG BOs that does not impose
artificial size limits and TTM evictions.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Bandwidth calculations are triggered for non zero streams, and
in case of 0 streams, these calculations were skipped with
pstate status not being updated.
[How]
As the pstate status is applicable for non zero streams, check
added for allowing 0 streams inline with dcn internal bandwidth
validations.
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For default cases,we should return 0. Otherwise resume will
abort because of the wrong return value.
Signed-off-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Correct reserved number according to the latest struct in drm-next
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There is no need to keep the dentry around for the debugfs kvmgt cache
file, as we can just look it up when we want to remove it later on.
Simplify the structure by removing the dentry and relying on debugfs
to find the dentry to remove when we want to.
By doing this change, we remove the last in-kernel user that was storing
the result of debugfs_create_long(), so that api can be cleaned up.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: intel-gvt-dev@lists.freedesktop.org
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210518161705.3697143-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'smuio_v13_0_is_host_gpu_xgmi_supported()' header
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/smuio_v13_0.c:99: warning: expecting prototype for smuio_v13_0_supports_host_gpu_xgmi(). Prototype was for smuio_v13_0_is_host_gpu_xgmi_supported() instead
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/gfx_v10_0.c:51: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/vcn_v1_0.c:775: warning: expecting prototype for vcn_v1_0_start(). Prototype was for vcn_v1_0_start_spg_mode() instead
drivers/gpu/drm/amd/amdgpu/vcn_v1_0.c:1111: warning: expecting prototype for vcn_v1_0_stop(). Prototype was for vcn_v1_0_stop_spg_mode() instead
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/sdma_v5_2.c:501: warning: expecting prototype for sdma_v_0_ctx_switch_enable(). Prototype was for sdma_v5_2_ctx_switch_enable() instead
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/amdgpu_vce.c:98: warning: expecting prototype for amdgpu_vce_init(). Prototype was for amdgpu_vce_sw_init() instead
drivers/gpu/drm/amd/amdgpu/amdgpu_vce.c:214: warning: expecting prototype for amdgpu_vce_fini(). Prototype was for amdgpu_vce_sw_fini() instead
drivers/gpu/drm/amd/amdgpu/amdgpu_vce.c:590: warning: expecting prototype for amdgpu_vce_cs_validate_bo(). Prototype was for amdgpu_vce_validate_bo() instead
drivers/gpu/drm/amd/amdgpu/amdgpu_vce.c:724: warning: expecting prototype for amdgpu_vce_cs_parse(). Prototype was for amdgpu_vce_ring_parse_cs() instead
drivers/gpu/drm/amd/amdgpu/amdgpu_vce.c:960: warning: expecting prototype for amdgpu_vce_cs_parse_vm(). Prototype was for amdgpu_vce_ring_parse_cs_vm() instead
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/sdma_v5_0.c:563: warning: expecting prototype for sdma_v_0_ctx_switch_enable(). Prototype was for sdma_v5_0_ctx_switch_enable() instead
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/sdma_v4_0.c:764: warning: expecting prototype for sdma_v4_0_page_ring_set_wptr(). Prototype was for sdma_v4_0_ring_set_wptr() instead
drivers/gpu/drm/amd/amdgpu/sdma_v4_0.c:830: warning: expecting prototype for sdma_v4_0_ring_set_wptr(). Prototype was for sdma_v4_0_page_ring_set_wptr() instead
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
'sdma_v2_4_ring_emit_hdp_flush()'
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/sdma_v2_4.c:281: warning: expecting prototype for sdma_v2_4_hdp_flush_ring_emit(). Prototype was for sdma_v2_4_ring_emit_hdp_flush() instead
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/gfx_v9_4_2.c:1008:5: warning: no previous prototype for ‘gfx_v9_4_2_query_ras_error_count’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/gfx_v9_4_2.c:1054:6: warning: no previous prototype for ‘gfx_v9_4_2_reset_ras_error_count’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/gfx_v9_4_2.c:1063:5: warning: no previous prototype for ‘gfx_v9_4_2_ras_error_inject’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/gfx_v9_4_2.c:1133:6: warning: no previous prototype for ‘gfx_v9_4_2_query_ras_error_status’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/gfx_v9_4_2.c:1143:6: warning: no previous prototype for ‘gfx_v9_4_2_reset_ras_error_status’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/gfx_v9_4_2.c:1153:6: warning: no previous prototype for ‘gfx_v9_4_2_enable_watchdog_timer’ [-Wmissing-prototypes]
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/radeon/r100.c:1423: warning: expecting prototype for r100_cs_packet_next_vline(). Prototype was for r100_cs_packet_parse_vline() instead
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/gmc_v10_0.c:955: warning: expecting prototype for gmc_v8_0_gart_fini(). Prototype was for gmc_v10_0_gart_fini() instead
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
'mmhub_v9_4_set_fault_enable_default()'
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/mmhub_v9_4.c:446: warning: expecting prototype for mmhub_v1_0_set_fault_enable_default(). Prototype was for mmhub_v9_4_set_fault_enable_default() instead
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/gmc_v7_0.c:526: warning: expecting prototype for gmc_v8_0_set_fault_enable_default(). Prototype was for gmc_v7_0_set_fault_enable_default() instead
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:259:29: warning: ‘XGMI2_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:252:29: warning: ‘XGMI1_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:245:29: warning: ‘XGMI0_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:238:29: warning: ‘WAFL1_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:231:29: warning: ‘WAFL0_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:161:29: warning: ‘PCIE0_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:119:29: warning: ‘L2IMU0_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:112:29: warning: ‘L1IMUPCIE0_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:105:29: warning: ‘L1IMUIOAGR0_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:98:29: warning: ‘IOHC0_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:91:29: warning: ‘IOAPIC0_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:84:29: warning: ‘IOAGR0_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:63:29: warning: ‘FUSE_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:49:29: warning: ‘DBGU_IO0_BASE’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../include/aldebaran_ip_offset.h:42:29: warning: ‘CLK_BASE’ defined but not used [-Wunused-const-variable=]
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/radeon/radeon_vm.c:61: warning: expecting prototype for radeon_vm_num_pde(). Prototype was for radeon_vm_num_pdes() instead
drivers/gpu/drm/radeon/radeon_vm.c:642: warning: expecting prototype for radeon_vm_update_pdes(). Prototype was for radeon_vm_update_page_directory() instead
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
