| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Only tpm_tis and tpm_tis_synquacer have a dedicated way to access
multiple bytes at once, every other driver will just fall back to
read_bytes/write_bytes. Therefore, remove the read16/read32/write32
calls and move their logic to read_bytes/write_bytes.
Suggested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Johannes Holland <johannes.holland@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In commit c46ed2281bbe ("tpm_tis_spi: add missing SPI device ID entries")
we added SPI IDs for all the DT aliases to handle the fact that we always
use SPI modaliases to load modules even when probed via DT however the
mentioned commit missed that the SPI and OF device ID entries did not
match and were different and so DT nodes with compatible
"tcg,tpm_tis-spi" will not match. Add an extra ID for tpm_tis-spi
rather than just fix the existing one since what's currently there is
going to be better for anyone actually using SPI IDs to instantiate.
Fixes: c46ed2281bbe ("tpm_tis_spi: add missing SPI device ID entries")
Fixes: 96c8395e2166 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
The SPI core always reports a "MODALIAS=spi:<foo>", even if the device was
registered via OF. This means that this module won't auto-load if a DT has
for example has a node with a compatible "infineon,slb9670" string.
In that case kmod will expect a "MODALIAS=of:N*T*Cinfineon,slb9670" uevent
but instead will get a "MODALIAS=spi:slb9670", which is not present in the
kernel module aliases:
$ modinfo drivers/char/tpm/tpm_tis_spi.ko | grep alias
alias: of:N*T*Cgoogle,cr50C*
alias: of:N*T*Cgoogle,cr50
alias: of:N*T*Ctcg,tpm_tis-spiC*
alias: of:N*T*Ctcg,tpm_tis-spi
alias: of:N*T*Cinfineon,slb9670C*
alias: of:N*T*Cinfineon,slb9670
alias: of:N*T*Cst,st33htpm-spiC*
alias: of:N*T*Cst,st33htpm-spi
alias: spi:cr50
alias: spi:tpm_tis_spi
alias: acpi*:SMO0768:*
To workaround this issue, add in the SPI device ID table all the entries
that are present in the OF device ID table.
Reported-by: Alexander Wellbrock <a.wellbrock@mailbox.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
In DSDT table, TPM _CID was SMO0768, and no _HID definition. After a
kernel upgrade from 4.19 to 5.10, TPM probe function was changed which
causes device probe fails. In order to make newer kernel to be
compatible with the older acpi definition, it would be best set default
probe function.
Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
On a Chromebook I'm working on I noticed a big (~1 second) delay
during bootup where nothing was happening. Right around this big
delay there were messages about the TPM:
[ 2.311352] tpm_tis_spi spi0.0: TPM ready IRQ confirmed on attempt 2
[ 3.332790] tpm_tis_spi spi0.0: Cr50 firmware version: ...
I put a few printouts in and saw that tpm_tis_spi_init() (specifically
tpm_chip_register() in that function) was taking the lion's share of
this time, though ~115 ms of the time was in cr50_print_fw_version().
Let's make a one-line change to prefer async probe for tpm_tis_spi.
There's no reason we need to block other drivers from probing while we
load.
NOTES:
* It's possible that other hardware runs through the init sequence
faster than Cr50 and this isn't such a big problem for them.
However, even if they are faster they are still doing _some_
transfers over a SPI bus so this should benefit everyone even if to
a lesser extent.
* It's possible that there are extra delays in the code that could be
optimized out. I didn't dig since once I enabled async probe they
no longer impacted me.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
During flow control we are just reading from the TPM, yet our spi_xfer
has the tx_buf and rx_buf both non-NULL which means we're requesting a
full duplex transfer.
SPI is always somewhat of a full duplex protocol anyway and in theory
the other side shouldn't really be looking at what we're sending it
during flow control, but it's still a bit ugly to be sending some
"random" data when we shouldn't.
The default tpm_tis_spi_flow_control() tries to address this by
setting 'phy->iobuf[0] = 0'. This partially avoids the problem of
sending "random" data, but since our tx_buf and rx_buf both point to
the same place I believe there is the potential of us sending the
TPM's previous byte back to it if we hit the retry loop.
Another flow control implementation, cr50_spi_flow_control(), doesn't
address this at all.
Let's clean this up and just make the tx_buf NULL before we call
flow_control(). Not only does this ensure that we're not sending any
"random" bytes but it also possibly could make the SPI controller
behave in a slightly more optimal way.
NOTE: no actual observed problems are fixed by this patch--it's was
just made based on code inspection.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
In a recent change to the SPI subsystem [1], a new 'delay' struct was added
to replace the 'delay_usecs'. This change replaces the current
'delay_usecs' with 'delay' for this driver.
The 'spi_transfer_delay_exec()' function [in the SPI framework] makes sure
that both 'delay_usecs' & 'delay' are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272df6485 ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Revert tpm_tis_spi_mod.ko back to tpm_tis_spi.ko as the rename could
break user space scripts. This can be achieved by renaming tpm_tis_spi.c
as tpm_tis_spi_main.c. Then tpm_tis_spi-y can be used inside the
makefile.
Cc: Andrey Pronin <apronin@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: stable@vger.kernel.org # 5.5.x
Fixes: 797c0113c9a4 ("tpm: tpm_tis_spi: Support cr50 devices")
Reported-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
