| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Interrupts specified through an "Interrupt" ACPI resource (versus through
a "GpioInt" resource) are now always assumed to be active low.
When this change was originally made the Thinkpad 8 quirk was kept around
because it was uncertain if the Thinkpad 8 uses an "Interrupt" or a
"GpioInt" resource.
Bug https://bugzilla.kernel.org/show_bug.cgi?id=196701 has a DSDT for the
Thinkpad 8 attached and it uses an "Interrupt" resource, so the quirk is
not necessary and the quirk, as well as the irq-active-low quirk handling
code can be removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Meegopad T08 hdmi-stick (think Intel computestick) has a brcm43430
wifi/bt combo chip. The BCM2E90 ACPI device describing the BT part does
contain a valid ActiveLow GpioInt entry, but the GPIO it points to never
goes low, so either the IRQ pin is not connected, or the ACPI resource-
table points to the wrong GPIO.
Eitherway things will not work if we try to use the specified IRQ, this
commits adds a DMI based broken-irq blacklist and disables use of the IRQ
and thus also runtime-pm for devices on this list.
This blacklist starts with the the Meegopad T08, fixing bluetooth not
working on this hdmi-stick. Since this is not a battery powered device
the loss of runtime-pm is not really an issue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
As Interrupt resource specified IRQs are now assumed to be always
active-low the DMI quirk for the MINIX Z83-4 is no longer required.
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Now that we need just an ACPI HID in the table, and the driver auto-
configures itself otherwise, we can easily add a bunch of known ACPI HIDs.
This avoids having to add these 1 by 1 as devices with one are encountered
by users.
This commit may seem as if it simply adds all IDs between BCM2E00-BCM2EAC,
but that is not true, all these IDs were found in actual .inf files and
the range is not entirely continuous, the following IDs are not added:
BCM2E6A, BCM2E6C, BCM2E8F and BCM2E91 because I did not see these in any
.inf files. As for the large amount of IDs this seems to be caused by
Broadcom using a separate ID for every bluetooth module using their
chips. E.g. BCM2EA6 seems to be specifically for the Raspberry Pi 3.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Since I've been doing a lot of work on Linux Bay Trail / Cherry Trail
support, I've gathered a collection of ACPI DSDTs from about 50 such
machines.
Looking at these DSTDs many have an ACPI device entry describing a bcm
bluetooth device (often disabled in the DSDT), quite a few of these ACPI
device entries have a resource-table where the order does not match with
the order currently associated with the HID of that entry in the
bcm_acpi_match table.
Looking at the Windows .inf files, there is nothing indicating a specific
order there, so I believe that there is no 1:1 mapping between the ACPI
HID and the order in which the resources are listed.
Therefor this commit replaces the hardcoded mapping based on ACPI HID,
with code which actually checks in which order the resources are listed
and bases the gpio-mapping on that.
This should ensure that we always pick the right mapping and this will
make adding new ACPI HIDs to the driver easier.
This has been tested on the following devices:
-Asus T100CHI BCM2E39 / brcmfmac43241b4-sdio / BCM4324B3-37.4M.hcd
-Asus T100TA BCM2E39 / brcmfmac43241b4-sdio / BCM4324B3-37.4M.hcd
-Asus T200TA BCM2E65 / brcmfmac43340-sdio / BCM43341B0-37.4M.hcd
-Jumper ezPad mini 3 BCM2E74 / brcmfmac43430a0-sdio / BCM4343A0-26M.hcd
-Acer Iconia Tab8 w1-8 BCM2E83 / brcmfmac4330-sdio / BCM4330B1-26M.hcd
-Chuwi Vi8 plus(CWI519) BCM2EAA / brcmfmac43430-sdio / BCM43430A1-26M.hcd
Which together cover all 3 combinations of using an Interrupt resource /
GpioInt resource as first resource / GpioInt resource as last resource.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
We declare the same set of const acpi_gpio_params twice with different
names, besides the needless duplication this naming leads to a sortof
double indirection which also makes it harder to see how the mapping is
actually setup.
This commit renames the first set to have generic names, which better
describe the contents of the mapping and drops the second set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add 6 new ACPI HIDs to enable bluetooth on devices using these HIDs,
I've tested the following HIDs / devices:
BCM2E74: Jumper ezPad mini 3
BCM2E83: Acer Iconia Tab8 w1-810
BCM2E90: Meegopad T08
BCM2EAA: Chuwi Vi8 plus (CWI519)
The reporter of Red Hat bugzilla 1554835 has tested:
BCM2E84: Lenovo Yoga2
The reporter of kernel bugzilla 274481 has tested:
BCM2E38: Toshiba Encore
Note the Lenovo Yoga2 and Toshiba Encore also needs the earlier patch to
treat all Interrupt ACPI resources as active low.
Cc: stable@vger.kernel.org
Buglink: https://bugzilla.kernel.org/attachment.cgi?id=274481
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1554835
Reported-and-tested-by: Robert R. Howell <rhowell@uwyo.edu>
Reported-and-tested-by: Christian Herzog <daduke@daduke.org>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Older devices with a serdev attached bcm bt hci, use an Interrupt ACPI
resource to describe the IRQ (rather then a GpioInt resource).
These device seem to all claim the IRQ is active-high and seem to all need
a DMI quirk to treat it as active-low. Instead simply always assume that
Interrupt resource specified IRQs are always active-low.
This fixes the bt device not being able to wake the host from runtime-
suspend on the: Asus T100TAM, Asus T200TA, Lenovo Yoga2 and the Toshiba
Encore, without the need to add 4 new DMI quirks for these models.
This also allows us to remove 2 DMI quirks for the Asus T100TA and Asus
T100CHI series. Likely the 2 remaining quirks can also be removed but I
could not find a DSDT of these devices to verify this.
Cc: stable@vger.kernel.org
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=198953
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1554835
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add irq_polarity module option for easier troubleshooting of irq-polarity
issues.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In case the shutdown GPIO is not wired up, it is impossible to reset the
Bluetooth controller to its original state. This include the initial
default baud rate which leads to issues when reloading the module or
when something unexpected happens. To avoid any kind of runtime
deadlocks, stick with the initial default baud rate.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Some GPIO controller drivers request sleepable context and so can't
be accessed from IRQ context. Using gpiod_set/get_value accessors
with such controller leads to a kernel warning since they are
reserved for atomic context (according to the documentation).
Use the postfixed _cansleep version instead, indicating that context
is safe for sleeping if necessary. Note that this is the case here
since we never toggle the gpio neither from IRQ nor from a spinlocked
section.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The IRQ output of the bcm bt-device is really a level IRQ signal, which
signals a logical high as long as the device's buffer contains data. Since
the draining in the buffer is done in the tty driver, we cannot (easily)
wait in a threaded interrupt handler for the draining, after which the
IRQ should go low again.
So instead we treat the IRQ as an edge interrupt. This opens the window
for a theoretical race where we wakeup, read some data and then autosuspend
*before* the IRQ has gone (logical) low, followed by the device just at
that moment receiving more data, causing the IRQ to stay high and we never
see an edge.
Since we call pm_runtime_mark_last_busy() on every received byte, there
should be plenty time for the IRQ to go (logical) low before we ever
suspend, so this should never happen, but after commit 43fff7683468
("Bluetooth: hci_bcm: Streamline runtime PM code"), which has been reverted
since, this was actually happening causing the device to get stuck in
runtime suspend.
The bcm bt-device actually has a workaround for this, if we set the
pulsed_host_wake flag in the sleep parameters, then the device monitors
if the host is draining the buffer and if not then after a timeout the
device will pulse the IRQ line, causing us to see an edge, fixing the
stuck in suspend condition.
This commit sets the pulsed_host_wake flag to fix the (mostly theoretical)
race caused by us treating the IRQ as an edge IRQ.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This reverts commit 43fff7683468 ("Bluetooth: hci_bcm: Streamline runtime
PM code"). The commit msg for this commit states "No functional change
intended.", but replacing:
pm_runtime_get();
pm_runtime_mark_last_busy();
pm_runtime_put_autosuspend();
with:
pm_request_resume();
Does result in a functional change, pm_request_resume() only calls
pm_runtime_mark_last_busy() if the device was suspended before the call.
This results in the following happening:
1) Device is runtime suspended
2) Device drives host_wake IRQ logically high as it starts receiving data
3) bcm_host_wake() gets called, causes the device to runtime-resume,
current time gets marked as last_busy time
4) After 5 seconds the autosuspend timer expires and the dev autosuspends
as no one has been calling pm_runtime_mark_last_busy(), the device was
resumed during those 5 seconds, so all the pm_request_resume() calls
while receiving data and/or bcm_host_wake() calls were nops
5) If 4) happens while the device has (just received) data in its buffer to
be read by the host the IRQ line is *already* / still logically high
when we autosuspend and since we use an edge triggered IRQ, the IRQ
will never trigger, causing the device to get stuck in suspend
Therefor this commit has to be reverted, so that we avoid the device
getting stuck in suspend.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
According to the devicetree binding the shutdown and device wake
GPIOs are optional. Since commit 3e81a4ca51a1 ("Bluetooth: hci_bcm:
Mandate presence of shutdown and device wake GPIO") this driver
won't probe anymore on Raspberry Pi 3 and Zero W (no device wake GPIO
connected). So fix this regression by reverting this commit partially.
Fixes: 3e81a4ca51a1 ("Bluetooth: hci_bcm: Mandate presence of shutdown and device wake GPIO")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Commit 8bfa7e1e03ac ("Bluetooth: hci_bcm: Handle errors properly")
introduced error checking for the bcm_gpio_set_power() call in bcm_open()
but the error-path it introduces unsets dev->hu, which is correct for
platform_device instantiated bcm_dev-s but not for serdev instantiated
devs. For serdev instantiated devs serdev_device_close() should be called
instead (and dev->hu should be left set).
Cc: Lukas Wunner <lukas@wunner.de>
Fixes: 8bfa7e1e03ac ("Bluetooth: hci_bcm: Handle errors properly")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
According to the documentation for Laird SD40 radio modules (which use
the BCM4329 chipset), the order of the Enable_BREAK_To_Host and
Pulsed_HOST_WAKE parameters in the sleep mode struct is reversed
vis-à-vis our struct declaration. See page 46 of this PDF:
http://cdn.lairdtech.com/home/brandworld/files/Application%20Note%20-%2040%20Series%20Bluetooth.pdf
The documentation is dated Oct 2015, so fairly recent, making it appear
more likely that the documentation is correct and our code is wrong.
Amend our code to be in congruence with the documentation.
Cc: Sue White <sue.white@lairdtech.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The driver calls mdelay(15) in the ->suspend, ->resume, ->runtime_suspend
and ->runtime_resume hook, however spinning for such a long period of
time is discouraged as per Documentation/timers/timers-howto.txt.
The use of mdelay() seems unnecessary, it is allowed to sleep in the
system sleep and runtime PM hooks (with the exception of ->suspend_noirq
and ->resume_noirq) and the driver itself also does not rely on a
non-sleeping ->runtime_resume as the only place where a synchronous
resume is performed, in bcm_dequeue(), is called from a work item in
hci_ldisc.c and hci_serdev.c.
So replace the mdelay(15) with msleep(15).
Note that the delay is inserted after asserting or deasserting the
device wake pin, but in bcm_gpio_set_power() that pin is asserted or
deasserted *without* observing a delay. It is thus unclear if the delay
is necessary at all. It is likewise unclear why it is exactly 15 ms,
the commit introducing it, 118612fb9165 ("Bluetooth: hci_bcm: Add
suspend/resume PM functions"), does not provide a rationale.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Suggested-and-reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The host wake IRQ is optional, but if none is found, "BCM irq: -22" is
logged which may irritate users. This is really a debug message, so use
dev_dbg() instead of dev_info(). If users are interested in the IRQ,
they can always consult /proc/interrupts.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Enable Bluetooth on the following Macs which provide custom ACPI methods
to toggle the GPIOs for device wake and shutdown instead of accessing
the pins directly:
MacBook8,1 2015 12"
MacBook9,1 2016 12"
MacBook10,1 2017 12"
MacBookPro13,1 2016 13"
MacBookPro13,2 2016 13" with Touch Bar
MacBookPro13,3 2016 15" with Touch Bar
MacBookPro14,1 2017 13"
MacBookPro14,2 2017 13" with Touch Bar
MacBookPro14,3 2017 15" with Touch Bar
On the MacBook8,1 Bluetooth is muxed with a second device (a debug port
on the SSD) under the control of PCH GPIO 36. Because serdev cannot
deal with multiple slaves yet, it is currently necessary to patch the
DSDT and remove the SSDC device.
The custom ACPI methods are called:
BTLP (Low Power) takes one argument, toggles device wake GPIO
BTPU (Power Up) tells SMC to drive shutdown GPIO high
BTPD (Power Down) tells SMC to drive shutdown GPIO low
BTRS (Reset) calls BTPD followed by BTPU
BTRB unknown, not present on all MacBooks
Search for the BTLP, BTPU and BTPD methods on ->probe and cache them in
struct bcm_device if the machine is a Mac.
Additionally, set the init_speed based on a custom device property
provided by Apple in lieu of _CRS resources. The Broadcom UART's speed
is fixed on Apple Macs: Any attempt to change it results in Bluetooth
status code 0x0c and bcm_set_baudrate() thus always returns -EBUSY.
By setting only the init_speed and leaving oper_speed at zero, we can
achieve that the host UART's speed is adjusted but the Broadcom UART's
speed is left as is.
The host wake pin goes into the SMC which handles it independently
of the OS, so there's no IRQ for it.
Thanks to Ronald Tschalär who did extensive debugging and testing of
this patch and contributed fixes.
ACPI snippet containing the custom methods and device properties
(taken from a MacBook8,1):
Method (BTLP, 1, Serialized)
{
If (LEqual (Arg0, 0x00))
{
Store (0x01, GD54) /* set PCH GPIO 54 direction to input */
}
If (LEqual (Arg0, 0x01))
{
Store (0x00, GD54) /* set PCH GPIO 54 direction to output */
Store (0x00, GP54) /* set PCH GPIO 54 value to low */
}
}
Method (BTPU, 0, Serialized)
{
Store (0x01, \_SB.PCI0.LPCB.EC.BTPC)
Sleep (0x0A)
}
Method (BTPD, 0, Serialized)
{
Store (0x00, \_SB.PCI0.LPCB.EC.BTPC)
Sleep (0x0A)
}
Method (BTRS, 0, Serialized)
{
BTPD ()
BTPU ()
}
Method (_DSM, 4, NotSerialized) // _DSM: Device-Specific Method
{
If (LEqual (Arg0, ToUUID ("a0b5b7c6-1318-441c-b0c9-fe695eaf949b")))
{
Store (Package (0x08)
{
"baud",
Buffer (0x08)
{ 0xC0, 0xC6, 0x2D, 0x00, 0x00, 0x00, 0x00, 0x00 },
"parity",
Buffer (0x08)
{ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 },
"dataBits",
Buffer (0x08)
{ 0x08, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 },
"stopBits",
Buffer (0x08)
{ 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }
}, Local0)
DTGP (Arg0, Arg1, Arg2, Arg3, RefOf (Local0))
Return (Local0)
}
Return (0x00)
}
Link: https://github.com/Dunedan/mbp-2016-linux/issues/29
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=110901
Reported-by: Leif Liddy <leif.liddy@gmail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Max Shavrick <mxms@me.com> [MacBook8,1]
Tested-by: Leif Liddy <leif.liddy@gmail.com> [MacBook9,1]
Tested-by: Daniel Roschka <danielroschka@phoenitydawn.de> [MacBookPro13,2]
Tested-by: Ronald Tschalär <ronald@innovation.ch> [MacBookPro13,3]
Tested-by: Peter Y. Chuang <peteryuchuang@gmail.com> [MacBookPro14,1]
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
A significant portion of this driver lacks error handling. As a first
step, add error paths to bcm_gpio_set_power(), bcm_open(), bcm_close(),
bcm_suspend_device(), bcm_resume_device(), bcm_resume(), bcm_probe() and
bcm_serdev_probe(). (I've also scrutinized bcm_suspend() but think it's
fine as is.)
Those are all the functions accessing the device wake and shutdown GPIO.
On Apple Macs the pins are accessed through ACPI methods, which may fail
for various reasons, hence proper error handling is necessary. Non-Macs
access the pins directly, which may fail as well but the GPIO core does
not yet pass back errors to consumers.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
MacBooks provides custom ACPI methods to toggle the GPIOs for device
wake and shutdown instead of accessing the pins directly. Prepare for
their support by adding callbacks to toggle the GPIOs, which on non-Macs
do nothing more but call gpiod_set_value().
No functional change intended.
Suggested-and-reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
If devm_request_irq() fails, the driver bails out of bcm_request_irq()
but continues to ->setup the device (because the IRQ is optional).
The driver subsequently calls devm_free_irq(), enable_irq_wake() and
disable_irq_wake() on the IRQ even though requesting it failed.
Avoid by invalidating the IRQ on request failure.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
On ->setup, pm_runtime_enable() is only called if a valid IRQ was found,
but on ->close(), pm_runtime_disable() is called unconditionally.
Disablement of runtime PM is recorded in a counter, so every
pm_runtime_disable() needs to be balanced. Fix it.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reported-and-reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Upon ->close, the driver powers the Bluetooth controller down, deasserts
the device wake pin, updates the runtime PM status to "suspended" and
finally frees the IRQ.
Because the IRQ is freed last, a runtime resume can take place after
the controller was powered down. The impact is not grave, the worst
thing that can happen is that the device wake pin is reasserted (should
have no effect while the regulator is off) and that setting the runtime
PM status to "suspended" does not reflect reality.
Still, it's wrong, so free the IRQ first.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
pm_runtime_disable() and pm_runtime_set_suspended() are replaced with
empty inlines if CONFIG_PM is disabled, so there's no need to #ifdef
them.
device_init_wakeup() is likewise replaced with an inline, though it's
not empty, but it and devm_free_irq() can be made conditional on
IS_ENABLED(CONFIG_PM), which is preferable to #ifdef as per section 20
of Documentation/process/coding-style.rst.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The ->close, ->suspend and ->resume hooks assume presence of a valid IRQ
if the device is wakeup capable. However it's entirely possible that
wakeup was enabled by some other entity besides this driver and in this
case the user will get a WARN splat if no valid IRQ was found. Avoid by
checking if the IRQ is valid, i.e. > 0.
Case in point: On recent MacBook Pros, the Bluetooth device lacks an
IRQ (because host wakeup is handled by the SMC, independently of the
operating system), but it does possess a _PRW method (which specifies
the SMC's GPE as wake event). The ACPI core therefore automatically
marks the physical Bluetooth device wakeup capable upon binding it to
its ACPI companion:
device_set_wakeup_capable+0x96/0xb0
acpi_bind_one+0x28a/0x310
acpi_platform_notify+0x20/0xa0
device_add+0x215/0x690
serdev_device_add+0x57/0xf0
acpi_serdev_add_device+0xc9/0x110
acpi_ns_walk_namespace+0x131/0x280
acpi_walk_namespace+0xf5/0x13d
serdev_controller_add+0x6f/0x110
serdev_tty_port_register+0x98/0xf0
tty_port_register_device_attr_serdev+0x3a/0x70
uart_add_one_port+0x268/0x500
serial8250_register_8250_port+0x32e/0x490
dw8250_probe+0x46c/0x720
platform_drv_probe+0x35/0x90
driver_probe_device+0x300/0x450
bus_for_each_drv+0x67/0xb0
__device_attach+0xde/0x160
bus_probe_device+0x9c/0xb0
device_add+0x448/0x690
platform_device_add+0x10e/0x260
mfd_add_device+0x392/0x4c0
mfd_add_devices+0xb1/0x110
intel_lpss_probe+0x2a9/0x610 [intel_lpss]
intel_lpss_pci_probe+0x7a/0xa8 [intel_lpss_pci]
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
[lukas: fix up ->suspend and ->resume as well, add commit message]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Commit 0395ffc1ee05 ("Bluetooth: hci_bcm: Add PM for BCM devices")
amended this driver to request a shutdown and device wake GPIO on probe,
but mandated that only one of them need to be present:
/* Make sure at-least one of the GPIO is defined and that
* a name is specified for this instance
*/
if ((!dev->device_wakeup && !dev->shutdown) || !dev->name) {
dev_err(&pdev->dev, "invalid platform data\n");
return -EINVAL;
}
However the same commit added a call to bcm_gpio_set_power() to the
->probe hook, which unconditionally accesses *both* GPIOs. Luckily,
the resulting NULL pointer deref was never reported, suggesting there's
no machine where either GPIO is missing.
Commit 8a92056837fd ("Bluetooth: hci_bcm: Add (runtime)pm support to the
serdev driver") removed the check whether at least one of the GPIOs is
present without specifying a reason.
Because commit 62aaefa7d038 ("Bluetooth: hci_bcm: improve use of gpios
API") refactored the driver to use devm_gpiod_get_optional() instead of
devm_gpiod_get(), one is now tempted to believe that the driver doesn't
require *any* of the two GPIOs.
Which is wrong, the driver still requires both GPIOs to avoid a NULL
pointer deref. To this end, establish the status quo ante and request
the GPIOs with devm_gpiod_get() again. Bail out of ->probe if either
of them is missing.
Oddly enough, whereas bcm_gpio_set_power() accesses the device wake pin
unconditionally, bcm_suspend_device() and bcm_resume_device() do check
for its presence before accessing it. Those checks are superfluous,
so remove them.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This driver seeks to force the Bluetooth device on for the duration of
5 seconds when the Bluetooth device has woken the host and after a
complete packet has been received. It does that by calling:
pm_runtime_get();
pm_runtime_mark_last_busy();
pm_runtime_put_autosuspend();
The same can be achieved more succinctly with:
pm_request_resume();
That's because after runtime resuming the device, rpm_resume() invokes
pm_runtime_mark_last_busy() followed by rpm_idle(), which will cause
the device to be suspended after expiration of the autosuspend_delay.
No functional change intended.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Asus T100HA laptop uses an ACPI HID of BCM2E72 for the bluetooth
part of the SDIO bcm43340 wifi/bt combo chip.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Tested on a GPD win with a BCM4356 PCI-E wifi/bt combo card.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This was introduced by the rework adding PM support:
drivers/bluetooth/hci_bcm.c: In function 'bcm_device_exists':
drivers/bluetooth/hci_bcm.c:156:22: error: 'struct bcm_device' has no member named 'hu'
if (device && device->hu && device->hu->serdev)
^~
The pointer is not available otherwise, so I'm enclosing
all references in an #ifdef here.
Fixes: 8a92056837fd ("Bluetooth: hci_bcm: Add (runtime)pm support to the serdev driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The MINIX NEO Z83-4 and MINIX NEO Z83-4 Pro devices use an AP6255 chip for
wifi and bluetooth. Bluetooth requires an ACPI device id of BCM2EA4 with
BCM4345 rev C0 firmware.
This patch adds the device id and to use trigger type IRQF_TRIGGER_FALLING
as defined by 'GpioInt' in the ACPI DSDT table:
Device (BLT0)
{
Name (_HID, "BCM2EA4") // _HID: Hardware ID
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (UBUF, ResourceTemplate ()
{
UartSerialBusV2 (0x0001C200, DataBitsEight, StopBitsOne,
0xFC, LittleEndian, ParityTypeNone, FlowControlHardware,
0x0020, 0x0020, "\\_SB.PCI0.URT1",
0x00, ResourceConsumer, , Exclusive,
)
GpioInt (Level, ActiveLow, Exclusive, PullNone, 0x0000,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0005
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0007
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0004
}
})
Return (UBUF) /* \_SB_.PCI0.URT1.BLT0._CRS.UBUF */
}
}
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
As the overwriting of IRQ polarity to active low occurs during the driver
probe using 'bt_dev_warn' to display the warning results in '(null)' being
displayed for the device. This patch uses 'dev_warn' to correctly display
the device in the warning instead.
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Make the serdev driver use struct bcm_device as its driver data and share
all the pm / GPIO / IRQ related code paths with the platform driver.
After this commit the 2 drivers are in essence the same and the serdev
driver interface can be used for all ACPI enumerated HCI UARTs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Use dev_get_drvdata instead of platform_get_drvdata in the suspend /
resume functions. This is a preparation patch for adding (runtime)pm
support to the serdev path.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The ACPI subsys is going to move over to instantiating ACPI enumerated
HCIs as serdevs, rather then as platform devices.
So we need to make bcm_acpi_probe() suitable for use on non platform-
devices too, which means that we cannot rely on platform_get_irq()
getting called.
This commit modifies bcm_acpi_probe() to directly get the irq from
the ACPI resources, this is a preparation patch for adding (runtime)pm
support to the serdev path.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
After our previous changes, there is nothing platform specific about
bcm_platform_probe anymore, rename it to bcm_get_resources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The ACPI subsys is going to move over to instantiating ACPI enumerated
HCIs as serdevs, rather then as platform devices.
This means that the serdev driver paths of hci_bcm.c also need to start
supporting (runtime)pm through GPIOs and a host-wake IRQ.
The hci_bcm code is already mostly independent of how the HCI gets
instantiated, but even though the code only cares about pdev->dev, it
was storing pdev itself in struct bcm_device.
This commit stores pdev->dev rather then pdev in struct bcm_device, this
is a preparation patch for adding (runtime)pm support to the serdev path.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The ACPI subsys is going to move over to instantiating ACPI enumerated
HCIs as serdevs, rather then as platform devices.
Most of the code in bcm_platform_probe is actually not platform
specific and will work with any struct device passed to it, the one
platform specific call in bcm_platform_probe is platform_get_irq.
This commit moves platform_get_irq call to the platform-driver's bcm_probe
function, this is a preparation patch for adding (runtime)pm support to
the serdev path.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Since bcm_acpi_probe calls bcm_platform_probe, bcm_probe always ends up
calling bcm_platform_probe.
This commit simplifies things by making bcm_probe always call
bcm_platform_probe itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This commit fixes 2 issues with host-wake irq trigger type handling
in hci_bcm:
1) bcm_setup_sleep sets sleep_params.host_wake_active based on
bcm_device.irq_polarity, but bcm_request_irq was always requesting
IRQF_TRIGGER_RISING as trigger type independent of irq_polarity.
This was a problem when the irq is described as a GpioInt rather then
an Interrupt in the DSDT as for GpioInt-s the value passed to request_irq
is honored. This commit fixes this by requesting the correct trigger
type depending on bcm_device.irq_polarity.
2) bcm_device.irq_polarity was used to directly store an ACPI polarity
value (ACPI_ACTIVE_*). This is undesirable because hci_bcm is also
used with device-tree and checking for something like ACPI_ACTIVE_LOW
in a non ACPI specific function like bcm_request_irq feels wrong.
This commit fixes this by renaming irq_polarity to irq_active_low
and changing its type to a bool.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Broadcom controller on the Raspberry Pi3 sends an empty packet with
packet type 0x00 after launching the firmware. This will cause logging
of errors.
Bluetooth: hci0: Frame reassembly failed (-84)
Since this seems to be an intented behaviour of the controller, handle
it gracefully by parsing that empty packet with packet type 0x00 and
then just simply report it as diagnostic packet.
With that change no errors are logging and the packet itself is actually
recorded in the Bluetooth monitor traces.
< HCI Command: Broadcom Launch RAM (0x3f|0x004e) plen 4
Address: 0xffffffff
> HCI Event: Command Complete (0x0e) plen 4
Broadcom Launch RAM (0x3f|0x004e) ncmd 1
Status: Success (0x00)
= Vendor Diagnostic (len 0)
< HCI Command: Broadcom Update UART Baud Rate (0x3f|0x0018) plen 6
00 00 00 10 0e 00 ......
> HCI Event: Command Complete (0x0e) plen 4
Broadcom Update UART Baud Rate (0x3f|0x0018) ncmd 1
Status: Success (0x00)
< HCI Command: Reset (0x03|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 4
Reset (0x03|0x0003) ncmd 1
Status: Success (0x00)
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Add basic support for Broadcom serial slave devices.
Probe the serial device, retrieve its maximum speed and
register a new hci uart device.
Tested/compatible with bcm43438 (RPi3).
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Not all Broadcom controller support the 4Mbps operational speed on UART
devices. This is because the UART clock setting changes might not be
supported.
< HCI Command: Broadcom Write UART Clock Setting (0x3f|0x0045) plen 1
01 .
> HCI Event: Command Complete (0x0e) plen 4
Broadcom Write UART Clock Setting (0x3f|0x0045) ncmd 1
Status: Unknown HCI Command (0x01)
To support any operational speed higher than 3Mbps, support for this
command is required. With that respect it is better to not enforce any
operational speed by default. Only when its support is known, then allow
for higher operational speed.
This patch assigns the 4Mbps opertional speed only for devices
discovered through ACPI and leave all others at the default 115200.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
In case of no IRQ resource associated to the bcm_device, requesting
IRQ should return an error in order to not enable low power mgmt.
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Reported-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Just like the T100TA the host-wake irq on the Asus T100CHI is
active low. Having a quirk for this is actually extra important on the
T100CHI as it ships with a bluetooth keyboard dock, which does not
work properly without this quirk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The hci_bcm proto is able to operate without bcm platform device linked
to its uart port. In that case, firmware can be applied, but there is
no power operation (no gpio/irq resources mgmt).
However, the current implementation breaks this use case because of
reporting a ENODEV error in the bcm setup procedure if bcm_request_irq
fails (which is the case if no bcm device linked).
Fix this by removing bcm_request_irq error forwarding.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Reported-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Joe and Bjørn suggested that it'd be nicer to not have the
cast in the fairly common case of doing
*(u8 *)skb_put(skb, 1) = c;
Add skb_put_u8() for this case, and use it across the code,
using the following spatch:
@@
expression SKB, C, S;
typedef u8;
identifier fn = {skb_put};
fresh identifier fn2 = fn ## "_u8";
@@
- *(u8 *)fn(SKB, S) = C;
+ fn2(SKB, C);
Note that due to the "S", the spatch isn't perfect, it should
have checked that S is 1, but there's also places that use a
sizeof expression like sizeof(var) or sizeof(u8) etc. Turns
out that nobody ever did something like
*(u8 *)skb_put(skb, 2) = c;
which would be wrong anyway since the second byte wouldn't be
initialized.
Suggested-by: Joe Perches <joe@perches.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
