Age | Commit message (Collapse) | Author | Files | Lines |
|
The existing values are rejected by the da9063 regulator driver, as they
are unachievable with the declared chip setup (non-merged vcore and bmem
are unable to provide the declared curent).
Fix voltages to match rev3 schematics, which also matches their boot-up
configuration within the chip's available precision.
Declare bcore1/bcore2 and bmem/bio as merged.
Set ldo09 and ldo10 as always-on as their consumers are not declared but
exist.
Drop ldo current limits as there is no current limit feature for these
regulators in the DA9063. Fixes warnings like:
DA9063_LDO3: Operation of current configuration missing
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
These sub-functions are available in the chip revision on this board, so
expose them.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Mark it as read-only as it is factory-programmed with identifying
information, and no executable nor configuration:
- eth MAC address
- board model (PCB version, BoM version)
- board serial number
Accidental modification would cause misidentification which could brick
the board, so marking read-only seem like both a safe and non-constraining
choice.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Follow the pin descriptions given in the version 3 of the board schematics.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Per HiFive Unmatched schematics, the card detect signal of the
micro SD card is connected to gpio pin #15, which should be
reflected in the DT via the <gpios> property, as described in
Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt.
[1] https://sifive.cdn.prismic.io/sifive/6a06d6c0-6e66-49b5-8e9e-e68ce76f4192_hifive-unmatched-schematics-v3.pdf
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Fixes: d573b5558abb ("riscv: dts: add initial board data for the SiFive HiFive Unmatched")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Per HiFive Unleashed schematics, the card detect signal of the
micro SD card is connected to gpio pin #11, which should be
reflected in the DT via the <gpios> property, as described in
Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt.
[1] https://sifive.cdn.prismic.io/sifive/c52a8e32-05ce-4aaf-95c8-7bf8453f8698_hifive-unleashed-a00-schematics-1.pdf
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Fixes: d573b5558abb ("riscv: dts: add initial board data for the SiFive HiFive Unmatched")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
When building external modules, vdso_prepare should not be run. If the
kernel sources are read-only, it will fail.
Fixes: fde9c59aebaf ("riscv: explicitly use symbol offsets for VDSO")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Let's enable KVM RISC-V in RV64 and RV32 defconfigs as module
so that it always built along with the default kernel image.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull more parisc fixes from Helge Deller:
"Fix a build error in stracktrace.c, fix resolving of addresses to
function names in backtraces, fix single-stepping in assembly code and
flush userspace pte's when using set_pte_at()"
* tag 'for-5.16/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc/entry: fix trace test in syscall exit path
parisc: Flush kernel data mapping in set_pte_at() when installing pte for user page
parisc: Fix implicit declaration of function '__kernel_text_address'
parisc: Fix backtrace to always include init funtion names
|
|
Pull arch/sh updates from Rich Felker.
* tag 'sh-for-5.16' of git://git.libc.org/linux-sh:
sh: pgtable-3level: Fix cast to pointer from integer of different size
sh: fix READ/WRITE redefinition warnings
sh: define __BIG_ENDIAN for math-emu
sh: math-emu: drop unused functions
sh: fix kconfig unmet dependency warning for FRAME_POINTER
sh: Cleanup about SPARSE_IRQ
sh: kdump: add some attribute to function
maple: fix wrong return value of maple_bus_init().
sh: boot: avoid unneeded rebuilds under arch/sh/boot/compressed/
sh: boot: add intermediate vmlinux.bin* to targets instead of extra-y
sh: boards: Fix the cacography in irq.c
sh: check return code of request_irq
sh: fix trivial misannotations
|
|
Pull ARM fixes from Russell King:
- Fix early_iounmap
- Drop cc-option fallbacks for architecture selection
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9156/1: drop cc-option fallbacks for architecture selection
ARM: 9155/1: fix early early_iounmap()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Two fixes due to DT node name changes on Arm, Ltd. boards
- Treewide rename of Ingenic CGU headers
- Update ST email addresses
- Remove Netlogic DT bindings
- Dropping few more cases of redundant 'maxItems' in schemas
- Convert toshiba,tc358767 bridge binding to schema
* tag 'devicetree-fixes-for-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: watchdog: sunxi: fix error in schema
bindings: media: venus: Drop redundant maxItems for power-domain-names
dt-bindings: Remove Netlogic bindings
clk: versatile: clk-icst: Ensure clock names are unique
of: Support using 'mask' in making device bus id
dt-bindings: treewide: Update @st.com email address to @foss.st.com
dt-bindings: media: Update maintainers for st,stm32-hwspinlock.yaml
dt-bindings: media: Update maintainers for st,stm32-cec.yaml
dt-bindings: mfd: timers: Update maintainers for st,stm32-timers
dt-bindings: timer: Update maintainers for st,stm32-timer
dt-bindings: i2c: imx: hardware do not restrict clock-frequency to only 100 and 400 kHz
dt-bindings: display: bridge: Convert toshiba,tc358767.txt to yaml
dt-bindings: Rename Ingenic CGU headers to ingenic,*.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 static call update from Thomas Gleixner:
"A single fix for static calls to make the trampoline patching more
robust by placing explicit signature bytes after the call trampoline
to prevent patching random other jumps like the CFI jump table
entries"
* tag 'locking-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
static_call,x86: Robustify trampoline patching
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Borislav Petkov:
- Avoid touching ~100 config files in order to be able to select the
preemption model
- clear cluster CPU masks too, on the CPU unplug path
- prevent use-after-free in cfs
- Prevent a race condition when updating CPU cache domains
- Factor out common shared part of smp_prepare_cpus() into a common
helper which can be called by both baremetal and Xen, in order to fix
a booting of Xen PV guests
* tag 'sched_urgent_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
preempt: Restore preemption model selection configs
arch_topology: Fix missing clear cluster_cpumask in remove_cpu_topology()
sched/fair: Prevent dead task groups from regaining cfs_rq's
sched/core: Mitigate race cpus_share_cache()/update_top_cache_domain()
x86/smp: Factor out parts of native_smp_prepare_cpus()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Prevent unintentional page sharing by checking whether a page
reference to a PMU samples page has been acquired properly before
that
- Make sure the LBR_SELECT MSR is saved/restored too
- Reset the LBR_SELECT MSR when resetting the LBR PMU to clear any
residual data left
* tag 'perf_urgent_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Avoid put_page() when GUP fails
perf/x86/vlbr: Add c->flags to vlbr event constraints
perf/x86/lbr: Reset LBR_SELECT during vlbr reset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Add the model number of a new, Raptor Lake CPU, to intel-family.h
- Do not log spurious corrected MCEs on SKL too, due to an erratum
- Clarify the path of paravirt ops patches upstream
- Add an optimization to avoid writing out AMX components to sigframes
when former are in init state
* tag 'x86_urgent_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add Raptor Lake to Intel family
x86/mce: Add errata workaround for Skylake SKX37
MAINTAINERS: Add some information to PARAVIRT_OPS entry
x86/fpu: Optimize out sigframe xfeatures when in init state
|
|
commit 8779e05ba8aa ("parisc: Fix ptrace check on syscall return")
fixed testing of TI_FLAGS. This uncovered a bug in the test mask.
syscall_restore_rfi is only used when the kernel needs to exit to
usespace with single or block stepping and the recovery counter
enabled. The test however used _TIF_SYSCALL_TRACE_MASK, which
includes a lot of bits that shouldn't be tested here.
Fix this by using TIF_SINGLESTEP and TIF_BLOCKSTEP directly.
I encountered this bug by enabling syscall tracepoints. Both in qemu and
on real hardware. As soon as i enabled the tracepoint (sys_exit_read,
but i guess it doesn't really matter which one), i got random page
faults in userspace almost immediately.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
user page
For years, there have been random segmentation faults in userspace on
SMP PA-RISC machines. It occurred to me that this might be a problem in
set_pte_at(). MIPS and some other architectures do cache flushes when
installing PTEs with the present bit set.
Here I have adapted the code in update_mmu_cache() to flush the kernel
mapping when the kernel flush is deferred, or when the kernel mapping
may alias with the user mapping. This simplifies calls to
update_mmu_cache().
I also changed the barrier in set_pte() from a compiler barrier to a
full memory barrier. I know this change is not sufficient to fix the
problem. It might not be needed.
I have had a few days of operation with 5.14.16 to 5.15.1 and haven't
seen any random segmentation faults on rp3440 or c8000 so far.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@kernel.org # 5.12+
|
|
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
I noticed that sometimes at kernel startup the backtraces did not
included the function names of init functions. Their address were not
resolved to function names and instead only the address was printed.
Debugging shows that the culprit is is_ksym_addr() which is called
by the backtrace functions to check if an address belongs to a function in
the kernel. The problem occurs only for CONFIG_KALLSYMS_ALL=y.
When looking at is_ksym_addr() one can see that for CONFIG_KALLSYMS_ALL=y
the function only tries to resolve the address via is_kernel() function,
which checks like this:
if (addr >= _stext && addr <= _end)
return 1;
On parisc the init functions are located before _stext, so this check fails.
Other platforms seem to have all functions (including init functions)
behind _stext.
The following patch moves the _stext symbol at the beginning of the
kernel and thus includes the init section. This fixes the check and does
not seem to have any negative side effects on where the kernel mapping
happens in the map_pages() function in arch/parisc/mm/init.c.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@kernel.org # 5.4+
|
|
Pull more kvm updates from Paolo Bonzini:
"New x86 features:
- Guest API and guest kernel support for SEV live migration
- SEV and SEV-ES intra-host migration
Bugfixes and cleanups for x86:
- Fix misuse of gfn-to-pfn cache when recording guest steal time /
preempted status
- Fix selftests on APICv machines
- Fix sparse warnings
- Fix detection of KVM features in CPUID
- Cleanups for bogus writes to MSR_KVM_PV_EOI_EN
- Fixes and cleanups for MSR bitmap handling
- Cleanups for INVPCID
- Make x86 KVM_SOFT_MAX_VCPUS consistent with other architectures
Bugfixes for ARM:
- Fix finalization of host stage2 mappings
- Tighten the return value of kvm_vcpu_preferred_target()
- Make sure the extraction of ESR_ELx.EC is limited to architected
bits"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (34 commits)
KVM: SEV: unify cgroup cleanup code for svm_vm_migrate_from
KVM: x86: move guest_pv_has out of user_access section
KVM: x86: Drop arbitrary KVM_SOFT_MAX_VCPUS
KVM: Move INVPCID type check from vmx and svm to the common kvm_handle_invpcid()
KVM: VMX: Add a helper function to retrieve the GPR index for INVPCID, INVVPID, and INVEPT
KVM: nVMX: Clean up x2APIC MSR handling for L2
KVM: VMX: Macrofy the MSR bitmap getters and setters
KVM: nVMX: Handle dynamic MSR intercept toggling
KVM: nVMX: Query current VMCS when determining if MSR bitmaps are in use
KVM: x86: Don't update vcpu->arch.pv_eoi.msr_val when a bogus value was written to MSR_KVM_PV_EOI_EN
KVM: x86: Rename kvm_lapic_enable_pv_eoi()
KVM: x86: Make sure KVM_CPUID_FEATURES really are KVM_CPUID_FEATURES
KVM: x86: Add helper to consolidate core logic of SET_CPUID{2} flows
kvm: mmu: Use fast PF path for access tracking of huge pages when possible
KVM: x86/mmu: Properly dereference rcu-protected TDP MMU sptep iterator
KVM: x86: inhibit APICv when KVM_GUESTDBG_BLOCKIRQ active
kvm: x86: Convert return type of *is_valid_rdpmc_ecx() to bool
KVM: x86: Fix recording of guest steal time / preempted status
selftest: KVM: Add intra host migration tests
selftest: KVM: Add open sev dev helper
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull vm86 fix from Eric Biederman:
"Just the removal of an unnecessary (and incorrect) test from a BUG_ON"
* 'exit-cleanups-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
signal/vm86_32: Remove pointless test in BUG_ON
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Vasily Gorbik:
- Add PCI automatic error recovery.
- Fix tape driver timer initialization broken during timers api
cleanup.
- Fix bogus CPU measurement counters values on CPUs offlining.
- Check the validity of subchanel before reading other fields in the
schib in cio code.
* tag 's390-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: check the subchannel validity for dev_busid
s390/cpumf: cpum_cf PMU displays invalid value after hotplug remove
s390/tape: fix timer initialization in tape_std_assign()
s390/pci: implement minimal PCI error recovery
PCI: Export pci_dev_lock()
s390/pci: implement reset_slot for hotplug slot
s390/pci: refresh function handle in iomap
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for time namespaces in the VDSO, along with some associated
cleanups.
- Support for building rv32 randconfigs.
- Improvements to the XIP port that allow larger kernels to function
- Various device tree cleanups for both the SiFive and Microchip boards
- A handful of defconfig updates, including enabling Nouveau.
There are also various small cleanups.
* tag 'riscv-for-linus-5.16-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: defconfig: enable DRM_NOUVEAU
riscv/vdso: Drop unneeded part due to merge issue
riscv: remove .text section size limitation for XIP
riscv: dts: sifive: add missing compatible for plic
riscv: dts: microchip: add missing compatibles for clint and plic
riscv: dts: sifive: drop duplicated nodes and properties in sifive
riscv: dts: sifive: fix Unleashed board compatible
riscv: dts: sifive: use only generic JEDEC SPI NOR flash compatible
riscv: dts: microchip: use vendor compatible for Cadence SD4HC
riscv: dts: microchip: drop unused pinctrl-names
riscv: dts: microchip: drop duplicated MMC/SDHC node
riscv: dts: microchip: fix board compatible
riscv: dts: microchip: drop duplicated nodes
dt-bindings: mmc: cdns: document Microchip MPFS MMC/SDHCI controller
riscv: add rv32 and rv64 randconfig build targets
riscv: mm: don't advertise 1 num_asid for 0 asid bits
riscv: set default pm_power_off to NULL
riscv/vdso: Add support for time namespaces
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull more MIPS updates from Thomas Bogendoerfer:
- Config updates for BMIPS platform
- Build fixes
- Makefile cleanups
* tag 'mips_5.16_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
mips: decompressor: do not copy source files while building
MIPS: boot/compressed/: add __bswapdi2() to target for ZSTD decompression
MIPS: fix duplicated slashes for Platform file path
MIPS: fix *-pkg builds for loongson2ef platform
PCI: brcmstb: Allow building for BMIPS_GENERIC
MIPS: BMIPS: Enable PCI Kconfig
MIPS: VDSO: remove -nostdlib compiler flag
mips: BCM63XX: ensure that CPU_SUPPORTS_32BIT_KERNEL is set
MIPS: Update bmips_stb_defconfig
MIPS: Allow modules to set board_be_handler
|
|
kernel test robot <oliver.sang@intel.com> writes[1]:
>
> Greeting,
>
> FYI, we noticed the following commit (built with gcc-9):
>
> commit: 1a4d21a23c4ca7467726be7db9ae8077a62b2c62 ("signal/vm86_32: Replace open coded BUG_ON with an actual BUG_ON")
> https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git master
>
> in testcase: trinity
> version: trinity-static-i386-x86_64-1c734c75-1_2020-01-06
> with following parameters:
>
>
> [ 70.645554][ T3747] kernel BUG at arch/x86/kernel/vm86_32.c:109!
> [ 70.646185][ T3747] invalid opcode: 0000 [#1] SMP
> [ 70.646682][ T3747] CPU: 0 PID: 3747 Comm: trinity-c6 Not tainted 5.15.0-rc1-00009-g1a4d21a23c4c #1
> [ 70.647598][ T3747] EIP: save_v86_state (arch/x86/kernel/vm86_32.c:109 (discriminator 3))
> [ 70.648113][ T3747] Code: 89 c3 64 8b 35 60 b8 25 c2 83 ec 08 89 55 f0 8b 96 10 19 00 00 89 55 ec e8 c6 2d 0c 00 fb 8b 55 ec 85 d2 74 05 83 3a 00 75 02 <0f> 0b 8b 86 10 19 00 00 8b 4b 38 8b 78 48 31 cf 89 f8 8b 7a 4c 81
> [ 70.650136][ T3747] EAX: 00000001 EBX: f5f49fac ECX: 0000000b EDX: f610b600
> [ 70.650852][ T3747] ESI: f5f79cc0 EDI: f5f79cc0 EBP: f5f49f04 ESP: f5f49ef0
> [ 70.651593][ T3747] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 EFLAGS: 00010246
> [ 70.652413][ T3747] CR0: 80050033 CR2: 00004000 CR3: 35fc7000 CR4: 000406d0
> [ 70.653169][ T3747] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
> [ 70.653897][ T3747] DR6: fffe0ff0 DR7: 00000400
> [ 70.654382][ T3747] Call Trace:
> [ 70.654719][ T3747] arch_do_signal_or_restart (arch/x86/kernel/signal.c:792 arch/x86/kernel/signal.c:867)
> [ 70.655288][ T3747] exit_to_user_mode_prepare (kernel/entry/common.c:174 kernel/entry/common.c:209)
> [ 70.655854][ T3747] irqentry_exit_to_user_mode (kernel/entry/common.c:126 kernel/entry/common.c:317)
> [ 70.656450][ T3747] irqentry_exit (kernel/entry/common.c:406)
> [ 70.656897][ T3747] exc_page_fault (arch/x86/mm/fault.c:1535)
> [ 70.657369][ T3747] ? sysvec_kvm_asyncpf_interrupt (arch/x86/mm/fault.c:1488)
> [ 70.657989][ T3747] handle_exception (arch/x86/entry/entry_32.S:1085)
vm86_32.c:109 is: "BUG_ON(!vm86 || !vm86->user_vm86)"
When trying to understand the failure Brian Gerst pointed out[2] that
the code does not need protection against vm86->user_vm86 being NULL.
The copy_from_user code will already handles that case if the address
is going to fault.
Looking futher I realized that if we care about not allowing struct
vm86plus_struct at address 0 it should be do_sys_vm86 (the system
call) that does the filtering. Not way down deep when the emulation
has completed in save_v86_state.
So let's just remove the silly case of attempting to filter a
userspace address with a BUG_ON. Existing userspace can't break and
it won't make the kernel any more attackable as the userspace access
helpers will handle it, if it isn't a good userspace pointer.
I have run the reproducer the fuzzer gave me before I made this change
and it reproduced, and after I made this change and I have not seen
the reported failure. So it does looks like this fixes the reported
issue.
[1] https://lkml.kernel.org/r/20211112074030.GB19820@xsang-OptiPlex-9020
[2] https://lkml.kernel.org/r/CAMzpN2jkK5sAv-Kg_kVnCEyVySiqeTdUORcC=AdG1gV6r8nUew@mail.gmail.com
Suggested-by: Brian Gerst <brgerst@gmail.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/arm64 fixes for 5.16, take #1
- Fix the host S2 finalization by solely iterating over the memblocks
instead of the whole IPA space
- Tighten the return value of kvm_vcpu_preferred_target() now that
32bit support is long gone
- Make sure the extraction of ESR_ELx.EC is limited to the architected
bits
- Comment fixups
|
|
Add model ID for Raptor Lake.
[ dhansen: These get added as soon as possible so that folks doing
development can leverage them. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20211112182835.924977-1-tony.luck@intel.com
|
|
Errata SKX37 is word-for-word identical to the other errata listed in
this workaround. I happened to notice this after investigating a CMCI
storm on a Skylake host. While I can't confirm this was the root cause,
spurious corrected errors does sound like a likely suspect.
Fixes: 2976908e4198 ("x86/mce: Do not log spurious corrected mce errors")
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20211029205759.GA7385@codemonkey.org.uk
|
|
Naresh and Antonio ran into a build failure with latest Debian
armhf compilers, with lots of output like
tmp/ccY3nOAs.s:2215: Error: selected processor does not support `cpsid i' in ARM mode
As it turns out, $(cc-option) fails early here when the FPU is not
selected before CPU architecture is selected, as the compiler
option check runs before enabling -msoft-float, which causes
a problem when testing a target architecture level without an FPU:
cc1: error: '-mfloat-abi=hard': selected architecture lacks an FPU
Passing e.g. -march=armv6k+fp in place of -march=armv6k would avoid this
issue, but the fallback logic is already broken because all supported
compilers (gcc-5 and higher) are much more recent than these options,
and building with -march=armv5t as a fallback no longer works.
The best way forward that I see is to just remove all the checks, which
also has the nice side-effect of slightly improving the startup time for
'make'.
The -mtune=marvell-f option was apparently never supported by any mainline
compiler, and the custom Codesourcery gcc build that did support is
now too old to build kernels, so just use -mtune=xscale unconditionally
for those.
This should be safe to apply on all stable kernels, and will be required
in order to keep building them with gcc-11 and higher.
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=996419
Reported-by: Antonio Terceiro <antonio.terceiro@linaro.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Cc: Matthias Klose <doko@debian.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Currently __set_fixmap() bails out with a warning when called in early boot
from early_iounmap(). Fix it, and while at it, make the comment a bit easier
to understand.
Cc: <stable@vger.kernel.org>
Fixes: b089c31c519c ("ARM: 8667/3: Fix memory attribute inconsistencies when using fixmap")
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Use the same cleanup code independent of whether the cgroup to be
uncharged and unref'd is the source or the destination cgroup. Use a
bool to track whether the destination cgroup has been charged, which also
fixes a bug in the error case: the destination cgroup must be uncharged
only if it does not match the source.
Fixes: b56639318bb2 ("KVM: SEV: Add support for SEV intra host migration")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When UBSAN is enabled, the code emitted for the call to guest_pv_has
includes a call to __ubsan_handle_load_invalid_value. objtool
complains that this call happens with UACCESS enabled; to avoid
the warning, pull the calls to user_access_begin into both arms
of the "if" statement, after the check for guest_pv_has.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Tidy up a bit the tree, by prefixing all include/dt-bindings/clock/ files
related to Ingenic SoCs with 'ingenic,'.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211016133322.40771-1-paul@crapouillou.net
|
|
Merge more updates from Andrew Morton:
"The post-linux-next material.
7 patches.
Subsystems affected by this patch series (all mm): debug,
slab-generic, migration, memcg, and kasan"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
kasan: add kasan mode messages when kasan init
mm: unexport {,un}lock_page_memcg
mm: unexport folio_memcg_{,un}lock
mm/migrate.c: remove MIGRATE_PFN_LOCKED
mm: migrate: simplify the file-backed pages validation when migrating its mapping
mm: allow only SLUB on PREEMPT_RT
mm/page_owner.c: modify the type of argument "order" in some functions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
"Only two changes.
One removes the now unused CONFIG_MCPU32 symbol. The other sets a
default for the CONFIG_MEMORY_RESERVE config symbol (this aids
scripting and other automation) so you don't interactively get asked
for a value at configure time.
Summary:
- remove unused CONFIG_MCPU32 symbol
- default CONFIG_MEMORY_RESERVE value (for scripting)"
* tag 'm68knommu-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: Remove MCPU32 config symbol
m68k: set a default value for MEMORY_RESERVE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, can and netfilter.
Current release - regressions:
- bpf: do not reject when the stack read size is different from the
tracked scalar size
- net: fix premature exit from NAPI state polling in napi_disable()
- riscv, bpf: fix RV32 broken build, and silence RV64 warning
Current release - new code bugs:
- net: fix possible NULL deref in sock_reserve_memory
- amt: fix error return code in amt_init(); fix stopping the
workqueue
- ax88796c: use the correct ioctl callback
Previous releases - always broken:
- bpf: stop caching subprog index in the bpf_pseudo_func insn
- security: fixups for the security hooks in sctp
- nfc: add necessary privilege flags in netlink layer, limit
operations to admin only
- vsock: prevent unnecessary refcnt inc for non-blocking connect
- net/smc: fix sk_refcnt underflow on link down and fallback
- nfnetlink_queue: fix OOB when mac header was cleared
- can: j1939: ignore invalid messages per standard
- bpf, sockmap:
- fix race in ingress receive verdict with redirect to self
- fix incorrect sk_skb data_end access when src_reg = dst_reg
- strparser, and tls are reusing qdisc_skb_cb and colliding
- ethtool: fix ethtool msg len calculation for pause stats
- vlan: fix a UAF in vlan_dev_real_dev() when ref-holder tries to
access an unregistering real_dev
- udp6: make encap_rcv() bump the v6 not v4 stats
- drv: prestera: add explicit padding to fix m68k build
- drv: felix: fix broken VLAN-tagged PTP under VLAN-aware bridge
- drv: mvpp2: fix wrong SerDes reconfiguration order
Misc & small latecomers:
- ipvs: auto-load ipvs on genl access
- mctp: sanity check the struct sockaddr_mctp padding fields
- libfs: support RENAME_EXCHANGE in simple_rename()
- avoid double accounting for pure zerocopy skbs"
* tag 'net-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (123 commits)
selftests/net: udpgso_bench_rx: fix port argument
net: wwan: iosm: fix compilation warning
cxgb4: fix eeprom len when diagnostics not implemented
net: fix premature exit from NAPI state polling in napi_disable()
net/smc: fix sk_refcnt underflow on linkdown and fallback
net/mlx5: Lag, fix a potential Oops with mlx5_lag_create_definer()
gve: fix unmatched u64_stats_update_end()
net: ethernet: lantiq_etop: Fix compilation error
selftests: forwarding: Fix packet matching in mirroring selftests
vsock: prevent unnecessary refcnt inc for nonblocking connect
net: marvell: mvpp2: Fix wrong SerDes reconfiguration order
net: ethernet: ti: cpsw_ale: Fix access to un-initialized memory
net: stmmac: allow a tc-taprio base-time of zero
selftests: net: test_vxlan_under_vrf: fix HV connectivity test
net: hns3: allow configure ETS bandwidth of all TCs
net: hns3: remove check VF uc mac exist when set by PF
net: hns3: fix some mac statistics is always 0 in device version V2
net: hns3: fix kernel crash when unload VF while it is being reset
net: hns3: sync rx ring head in echo common pull
net: hns3: fix pfc packet number incorrect after querying pfc parameters
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fix from Greg KH:
"Here is a single fix for 5.16-rc1 to resolve a build problem that came
in through the coresight tree (and as such came in through the
char/misc tree merge in the 5.16-rc1 merge window).
It resolves a build problem with 'allmodconfig' on arm64 and is acked
by the proper subsystem maintainers. It has been in linux-next all
week with no reported problems"
* tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
arm64: cpufeature: Export this_cpu_has_cap helper
|
|
There are multiple kasan modes. It makes sense that we add some
messages to know which kasan mode is active when booting up [1].
Link: https://bugzilla.kernel.org/show_bug.cgi?id=212195 [1]
Link: https://lkml.kernel.org/r/20211020094850.4113-1-Kuan-Ying.Lee@mediatek.com
Signed-off-by: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com>
Reviewed-by: Marco Elver <elver@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: Yee Lee <yee.lee@mediatek.com>
Cc: Nicholas Tang <nicholas.tang@mediatek.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
MIGRATE_PFN_LOCKED is used to indicate to migrate_vma_prepare() that a
source page was already locked during migrate_vma_collect(). If it
wasn't then the a second attempt is made to lock the page. However if
the first attempt failed it's unlikely a second attempt will succeed,
and the retry adds complexity. So clean this up by removing the retry
and MIGRATE_PFN_LOCKED flag.
Destination pages are also meant to have the MIGRATE_PFN_LOCKED flag
set, but nothing actually checks that.
Link: https://lkml.kernel.org/r/20211025041608.289017-1-apopple@nvidia.com
Signed-off-by: Alistair Popple <apopple@nvidia.com>
Reviewed-by: Ralph Campbell <rcampbell@nvidia.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* Fix misuse of gfn-to-pfn cache when recording guest steal time / preempted status
* Fix selftests on APICv machines
* Fix sparse warnings
* Fix detection of KVM features in CPUID
* Cleanups for bogus writes to MSR_KVM_PV_EOI_EN
* Fixes and cleanups for MSR bitmap handling
* Cleanups for INVPCID
* Make x86 KVM_SOFT_MAX_VCPUS consistent with other architectures
|
|
Add support for AMD SEV and SEV-ES intra-host migration support. Intra
host migration provides a low-cost mechanism for userspace VMM upgrades.
In the common case for intra host migration, we can rely on the normal
ioctls for passing data from one VMM to the next. SEV, SEV-ES, and other
confidential compute environments make most of this information opaque, and
render KVM ioctls such as "KVM_GET_REGS" irrelevant. As a result, we need
the ability to pass this opaque metadata from one VMM to the next. The
easiest way to do this is to leave this data in the kernel, and transfer
ownership of the metadata from one KVM VM (or vCPU) to the next. In-kernel
hand off makes it possible to move any data that would be
unsafe/impossible for the kernel to hand directly to userspace, and
cannot be reproduced using data that can be handed to userspace.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM_CAP_NR_VCPUS is used to get the "recommended" maximum number of
VCPUs and arm64/mips/riscv report num_online_cpus(). Powerpc reports
either num_online_cpus() or num_present_cpus(), s390 has multiple
constants depending on hardware features. On x86, KVM reports an
arbitrary value of '710' which is supposed to be the maximum tested
value but it's possible to test all KVM_MAX_VCPUS even when there are
less physical CPUs available.
Drop the arbitrary '710' value and return num_online_cpus() on x86 as
well. The recommendation will match other architectures and will mean
'no CPU overcommit'.
For reference, QEMU only queries KVM_CAP_NR_VCPUS to print a warning
when the requested vCPU number exceeds it. The static limit of '710'
is quite weird as smaller systems with just a few physical CPUs should
certainly "recommend" less.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211111134733.86601-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Handle #GP on INVPCID due to an invalid type in the common switch
statement instead of relying on the callers (VMX and SVM) to manually
validate the type.
Unlike INVVPID and INVEPT, INVPCID is not explicitly documented to check
the type before reading the operand from memory, so deferring the
type validity check until after that point is architecturally allowed.
Signed-off-by: Vipin Sharma <vipinsh@google.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211109174426.2350547-3-vipinsh@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
INVVPID, and INVEPT
handle_invept(), handle_invvpid(), handle_invpcid() read the same reg2
field in vmcs.VMX_INSTRUCTION_INFO to get the index of the GPR that
holds the invalidation type. Add a helper to retrieve reg2 from VMX
instruction info to consolidate and document the shift+mask magic.
Signed-off-by: Vipin Sharma <vipinsh@google.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211109174426.2350547-2-vipinsh@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Clean up the x2APIC MSR bitmap intereption code for L2, which is the last
holdout of open coded bitmap manipulations. Freshen up the SDM/PRM
comment, rename the function to make it abundantly clear the funky
behavior is x2APIC specific, and explain _why_ vmcs01's bitmap is ignored
(the previous comment was flat out wrong for x2APIC behavior).
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211109013047.2041518-5-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add builder macros to generate the MSR bitmap helpers to reduce the
amount of copy-paste code, especially with respect to all the magic
numbers needed to calc the correct bit location.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211109013047.2041518-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Always check vmcs01's MSR bitmap when merging L0 and L1 bitmaps for L2,
and always update the relevant bits in vmcs02. This fixes two distinct,
but intertwined bugs related to dynamic MSR bitmap modifications.
The first issue is that KVM fails to enable MSR interception in vmcs02
for the FS/GS base MSRs if L1 first runs L2 with interception disabled,
and later enables interception.
The second issue is that KVM fails to honor userspace MSR filtering when
preparing vmcs02.
Fix both issues simultaneous as fixing only one of the issues (doesn't
matter which) would create a mess that no one should have to bisect.
Fixing only the first bug would exacerbate the MSR filtering issue as
userspace would see inconsistent behavior depending on the whims of L1.
Fixing only the second bug (MSR filtering) effectively requires fixing
the first, as the nVMX code only knows how to transition vmcs02's
bitmap from 1->0.
Move the various accessor/mutators that are currently buried in vmx.c
into vmx.h so that they can be shared by the nested code.
Fixes: 1a155254ff93 ("KVM: x86: Introduce MSR filtering")
Fixes: d69129b4e46a ("KVM: nVMX: Disable intercept for FS/GS base MSRs in vmcs02 when possible")
Cc: stable@vger.kernel.org
Cc: Alexander Graf <graf@amazon.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211109013047.2041518-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Check the current VMCS controls to determine if an MSR write will be
intercepted due to MSR bitmaps being disabled. In the nested VMX case,
KVM will disable MSR bitmaps in vmcs02 if they're disabled in vmcs12 or
if KVM can't map L1's bitmaps for whatever reason.
Note, the bad behavior is relatively benign in the current code base as
KVM sets all bits in vmcs02's MSR bitmap by default, clears bits if and
only if L0 KVM also disables interception of an MSR, and only uses the
buggy helper for MSR_IA32_SPEC_CTRL. Because KVM explicitly tests WRMSR
before disabling interception of MSR_IA32_SPEC_CTRL, the flawed check
will only result in KVM reading MSR_IA32_SPEC_CTRL from hardware when it
isn't strictly necessary.
Tag the fix for stable in case a future fix wants to use
msr_write_intercepted(), in which case a buggy implementation in older
kernels could prove subtly problematic.
Fixes: d28b387fb74d ("KVM/VMX: Allow direct access to MSR_IA32_SPEC_CTRL")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211109013047.2041518-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
written to MSR_KVM_PV_EOI_EN
When kvm_gfn_to_hva_cache_init() call from kvm_lapic_set_pv_eoi() fails,
MSR write to MSR_KVM_PV_EOI_EN results in #GP so it is reasonable to
expect that the value we keep internally in KVM wasn't updated.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211108152819.12485-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|