| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The imx6 SMP system has the same DMA memory coherency issue [1] with
pl310 L2 controller. With this shared override bit set, the customer
reports the DMA coherency issue is gone. Besides, I have tested
the performance using USB ethernet with/without this bit, it shows
no difference.
[1] http://patchwork.ozlabs.org/patch/469362/
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
With the SION bit set a pin can be read as GPIO even though it's not muxed
as GPIO. This is useful at times. The downside however is that the signal
is not only routed to the GPIO IP but also all other IPs that can make use
of the pin. This resulted in more than one issue for me in the past. Things
like spi transfers that result in usb reenumeration or setting a GPIO to a
value that triggers an RTS irq for an UART.
This convinces me that the SION bit does more harm than good and so all
SION bits are removed that are not known to be needed.
Note that this has no influence on GPIOs under Linux as the gpio-mxc
driver just reports the level the pin is driven to for outputs and not
the level as seen on the pin.
If this commit introduces a regression for you, please report which SION
bit is essential for your setup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add "dis_rxdet_inp3_quirk" boolean property to USB3 node. This property
is used to disable rx detection in P3 PHY mode.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PCI reset GPIO is active low, so represent it with the
GPIO_ACTIVE_LOW flag.
Even though the imx6 PCI driver will not take the polarity into account
in this case, it is better to provide a correct description in device-tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license. In particular, the Utilite Pro
devicetree file (which includes imx6q-cm-fx6.dts) is already dual
licensed under GPLv2/X11.
Hence, relicense imx6q-cm-fx6.dts under GPLv2/X11 dual license.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The CompuLab Utilite Pro is a miniature fanless desktop pc based on
the i.MX6 Quad powered cm-fx6 module. It features two serial ports,
USB OTG, 4x USB, analog audio and S/PDIF, 2x Gb Ethernet, HDMI and
DVI ports, an on-board 32GB SSD, a mmc slot, and on-board wifi/bt.
Add initial support for it including USB, Ethernet (both ports), sata
and HDMI support.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The cm-fx6 module has an on-board spi-flash chip for its firmware, an
eeprom (containing e.g. the mac address of the on-board Ethernet),
a sata port, a pcie controller, an USB hub, and an USB otg port.
Enable support for them. In addition, enable syscon poweroff support.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The imx6q-cm-fx6 iomuxc container node is not required. Remove it.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This fixes the following dtc warning by removing the unnecessary unit:
Warning (unit_address_vs_reg): Node /matrix-keypad@0 has a unit name,
but no reg property
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This fixes the following dtc warning by removing the unnecessary unit:
Warning (unit_address_vs_reg): Node /onewire@0 has a unit name,
but no reg property
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds the missing reg properties for the regulator nodes
in order to fix the dtc warnings.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds the missing reg properties for the MXS GPIO banks
in order to fix the dtc warnings.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Auvidea H100 is a baseboard for the SolidRun MicroSOM.
Its primary feature is a Toshiba TC358743 HDMI to CSI decoder,
allowing the board to work as HDMI passthrough and framegrabber.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the DT property to all boards that have the hardware workaround
for erratum ERR006687 present. This allows the CPUidle driver to use
the deep idle states, even if the FEC is active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This node describes the DI1 port of IPU, fix the node name to reflect this.
There's currently no user of this node in mainline, so this change should
not break any supported platforms.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the LCD8000-43T display and for the backlight
controlled via PWM1.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
As of commit 1006ed7e1b258dac ("serial: imx: Use generic uart-has-rtscts
DT property"), the Freescale IMX UART driver recognizes the generic
"uart-has-rtscts" DT property, deprecating the vendor-specific
"fsl,uart-has-rtscts" DT property. Hence replace the latter by the
former in all DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
As of commit 182cdcb8bb16e687 ("serial: mxs-auart: Use generic
uart-has-rtscts DT property"), the Freescale MXS AUART driver recognizes
the generic "uart-has-rtscts" DT property, deprecating the
vendor-specific "fsl,uart-has-rtscts" DT property. Hence replace the
latter by the former in all DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for this small MP3 player based on STMP3780 (rev.3).
Currently supported are both external microSD and internal SD-NAND
bridge, PWM and USB gadget.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for this small MP3 player based on STMP3780 (rev.4).
Currently supported is both external microSD and internal SD-NAND
bridge, PWM and USB gadget.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add 2-pin pinmux settings for AUART2.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add pinmux configuration for SSP2 port in SD mode, both for
the 4-bit and 8-bit case.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This enables support for the CAN controller located in the FPGA.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable FPGA's IRQ controller. It is in charge of dispatching interrupts
generated by IPs in the FPGA. The SoC is notified that an interrupt
occurred through a GPIO.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add input mux for UART2 RX in DTE mode. This allows to use the pad
UART2_TX_DATA_ALT0 as UART2 RX. This particular input select seems
to be missing in current reference manuals (Rev. B), but when looking
at the tables and other UART input select registers (e.g. UART3) it
seems naturally that this input mux register also has a fourth pad
option for UART2_TX_DATA_ALT0. It has also been proven to be required
to use UART2 in DTE mode and the particular pads on the Colibri iMX7
platform.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pass "fsl,sai-mclk-direction-output" to the sai2 node, so that the
SAI2_MCLK can be an output.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add SAI alias entries, which makes it possibe for the SAI driver
to retrieve the port instance.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Building with W=1 option leads to several warnings like:
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-1p1@110 has a unit name, but no reg property
Fix them by removing the unneeded unit-addresses.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add clocks property for ocotp node.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add clocks property for ocotp node.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull more MIPS updates from Ralf Baechle:
"This is the secondnd batch of MIPS patches for 4.7. Summary:
CPS:
- Copy EVA configuration when starting secondary VPs.
EIC:
- Clear Status IPL.
Lasat:
- Fix a few off by one bugs.
lib:
- Mark intrinsics notrace. Not only are the intrinsics
uninteresting, it would cause infinite recursion.
MAINTAINERS:
- Add file patterns for MIPS BRCM device tree bindings.
- Add file patterns for mips device tree bindings.
MT7628:
- Fix MT7628 pinmux typos.
- wled_an pinmux gpio.
- EPHY LEDs pinmux support.
Pistachio:
- Enable KASLR
VDSO:
- Build microMIPS VDSO for microMIPS kernels.
- Fix aliasing warning by building with `-fno-strict-aliasing' for
debugging but also tracing them might result in recursion.
Misc:
- Add missing FROZEN hotplug notifier transitions.
- Fix clk binding example for varioius PIC32 devices.
- Fix cpu interrupt controller node-names in the DT files.
- Fix XPA CPU feature separation.
- Fix write_gc0_* macros when writing zero.
- Add inline asm encoding helpers.
- Add missing VZ accessor microMIPS encodings.
- Fix little endian microMIPS MSA encodings.
- Add 64-bit HTW fields and fix its configuration.
- Fix sigreturn via VDSO on microMIPS kernel.
- Lots of typo fixes.
- Add definitions of SegCtl registers and use them"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (49 commits)
MIPS: Add missing FROZEN hotplug notifier transitions
MIPS: Build microMIPS VDSO for microMIPS kernels
MIPS: Fix sigreturn via VDSO on microMIPS kernel
MIPS: devicetree: fix cpu interrupt controller node-names
MIPS: VDSO: Build with `-fno-strict-aliasing'
MIPS: Pistachio: Enable KASLR
MIPS: lib: Mark intrinsics notrace
MIPS: Fix 64-bit HTW configuration
MIPS: Add 64-bit HTW fields
MAINTAINERS: Add file patterns for mips device tree bindings
MAINTAINERS: Add file patterns for mips brcm device tree bindings
MIPS: Simplify DSP instruction encoding macros
MIPS: Add missing tlbinvf/XPA microMIPS encodings
MIPS: Fix little endian microMIPS MSA encodings
MIPS: Add missing VZ accessor microMIPS encodings
MIPS: Add inline asm encoding helpers
MIPS: Spelling fix lets -> let's
MIPS: VR41xx: Fix typo
MIPS: oprofile: Fix typo
MIPS: math-emu: Fix typo
...
|
|
Pull string hash improvements from George Spelvin:
"This series does several related things:
- Makes the dcache hash (fs/namei.c) useful for general kernel use.
(Thanks to Bruce for noticing the zero-length corner case)
- Converts the string hashes in <linux/sunrpc/svcauth.h> to use the
above.
- Avoids 64-bit multiplies in hash_64() on 32-bit platforms. Two
32-bit multiplies will do well enough.
- Rids the world of the bad hash multipliers in hash_32.
This finishes the job started in commit 689de1d6ca95 ("Minimal
fix-up of bad hashing behavior of hash_64()")
The vast majority of Linux architectures have hardware support for
32x32-bit multiply and so derive no benefit from "simplified"
multipliers.
The few processors that do not (68000, h8/300 and some models of
Microblaze) have arch-specific implementations added. Those
patches are last in the series.
- Overhauls the dcache hash mixing.
The patch in commit 0fed3ac866ea ("namei: Improve hash mixing if
CONFIG_DCACHE_WORD_ACCESS") was an off-the-cuff suggestion.
Replaced with a much more careful design that's simultaneously
faster and better. (My own invention, as there was noting suitable
in the literature I could find. Comments welcome!)
- Modify the hash_name() loop to skip the initial HASH_MIX(). This
would let us salt the hash if we ever wanted to.
- Sort out partial_name_hash().
The hash function is declared as using a long state, even though
it's truncated to 32 bits at the end and the extra internal state
contributes nothing to the result. And some callers do odd things:
- fs/hfs/string.c only allocates 32 bits of state
- fs/hfsplus/unicode.c uses it to hash 16-bit unicode symbols not bytes
- Modify bytemask_from_count to handle inputs of 1..sizeof(long)
rather than 0..sizeof(long)-1. This would simplify users other
than full_name_hash"
Special thanks to Bruce Fields for testing and finding bugs in v1. (I
learned some humbling lessons about "obviously correct" code.)
On the arch-specific front, the m68k assembly has been tested in a
standalone test harness, I've been in contact with the Microblaze
maintainers who mostly don't care, as the hardware multiplier is never
omitted in real-world applications, and I haven't heard anything from
the H8/300 world"
* 'hash' of git://ftp.sciencehorizons.net/linux:
h8300: Add <asm/hash.h>
microblaze: Add <asm/hash.h>
m68k: Add <asm/hash.h>
<linux/hash.h>: Add support for architecture-specific functions
fs/namei.c: Improve dcache hash function
Eliminate bad hash multipliers from hash_32() and hash_64()
Change hash_64() return value to 32 bits
<linux/sunrpc/svcauth.h>: Define hash_str() in terms of hashlen_string()
fs/namei.c: Add hashlen_string() function
Pull out string hash to <linux/stringhash.h>
|
|
This will improve the performance of hash_32() and hash_64(), but due
to complete lack of multi-bit shift instructions on H8, performance will
still be bad in surrounding code.
Designing H8-specific hash algorithms to work around that is a separate
project. (But if the maintainers would like to get in touch...)
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
|
|
Microblaze is an FPGA soft core that can be configured various ways.
If it is configured without a multiplier, the standard __hash_32()
will require a call to __mulsi3, which is a slow software loop.
Instead, use a shift-and-add sequence for the constant multiply.
GCC knows how to do this, but it's not as clever as some.
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
|
|
This provides a multiply by constant GOLDEN_RATIO_32 = 0x61C88647
for the original mc68000, which lacks a 32x32-bit multiply instruction.
Yes, the amount of optimization effort put in is excessive. :-)
Shift-add chain found by Yevgen Voronenko's Hcub algorithm at
http://spiral.ece.cmu.edu/mcm/gen.html
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Philippe De Muyter <phdm@macq.eu>
Cc: linux-m68k@lists.linux-m68k.org
|
|
This is just the infrastructure; there are no users yet.
This is modelled on CONFIG_ARCH_RANDOM; a CONFIG_ symbol declares
the existence of <asm/hash.h>.
That file may define its own versions of various functions, and define
HAVE_* symbols (no CONFIG_ prefix!) to suppress the generic ones.
Included is a self-test (in lib/test_hash.c) that verifies the basics.
It is NOT in general required that the arch-specific functions compute
the same thing as the generic, but if a HAVE_* symbol is defined with
the value 1, then equality is tested.
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Philippe De Muyter <phdm@macq.eu>
Cc: linux-m68k@lists.linux-m68k.org
Cc: Alistair Francis <alistai@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
|
|
The corresponding FROZEN hotplug notifier transitions used on
suspend/resume are ignored. Therefore the switch case action argument
is masked with the frozen hotplug notifier transition mask.
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: rt@linutronix.de
Patchwork: https://patchwork.linux-mips.org/patch/13351/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
MicroMIPS kernels may be expected to run on microMIPS only cores which
don't support the normal MIPS instruction set, so be sure to pass the
-mmicromips flag through to the VDSO cflags.
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.4.x-
Patchwork: https://patchwork.linux-mips.org/patch/13349/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
In microMIPS kernels, handle_signal() sets the isa16 mode bit in the
vdso address so that the sigreturn trampolines (which are offset from
the VDSO) get executed as microMIPS.
However commit ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
changed the offsets to come from the VDSO image, which already have the
isa16 mode bit set correctly since they're extracted from the VDSO
shared library symbol table.
Drop the isa16 mode bit handling from handle_signal() to fix sigreturn
for cores which support both microMIPS and normal MIPS. This doesn't fix
microMIPS only cores, since the VDSO is still built for normal MIPS, but
thats a separate problem.
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.4.x-
Patchwork: https://patchwork.linux-mips.org/patch/13348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Here is the quote from [1]:
The unit-address must match the first address specified
in the reg property of the node. If the node has no reg property,
the @ and unit-address must be omitted and the node-name alone
differentiates the node from other nodes at the same level
This patch adjusts MIPS dts-files and devicetree binding
documentation in accordance with [1].
[1] Power.org(tm) Standard for Embedded Power Architecture(tm)
Platform Requirements (ePAPR). Version 1.1 – 08 April 2011.
Chapter 2.2.1.1 Node Name Requirements
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13345/
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Avoid an aliasing issue causing a build error in VDSO:
In file included from include/linux/srcu.h:34:0,
from include/linux/notifier.h:15,
from ./arch/mips/include/asm/uprobes.h:9,
from include/linux/uprobes.h:61,
from include/linux/mm_types.h:13,
from ./arch/mips/include/asm/vdso.h:14,
from arch/mips/vdso/vdso.h:27,
from arch/mips/vdso/gettimeofday.c:11:
include/linux/workqueue.h: In function 'work_static':
include/linux/workqueue.h:186:2: error: dereferencing type-punned pointer will break strict-aliasing rules [-Werror=strict-aliasing]
return *work_data_bits(work) & WORK_STRUCT_STATIC;
^
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/vdso/gettimeofday.o] Error 1
with a CONFIG_DEBUG_OBJECTS_WORK configuration and GCC 5.2.0. Include
`-fno-strict-aliasing' along with compiler options used, as required for
kernel code, fixing a problem present since the introduction of VDSO
with commit ebb5e78cc634 ("MIPS: Initial implementation of a VDSO").
Thanks to Tejun for diagnosing this properly!
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.3+
Patchwork: https://patchwork.linux-mips.org/patch/13357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Allow KASLR to be selected on Pistachio based systems. Tested on a
Creator Ci40.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13356/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
On certain MIPS32 devices, the ftrace tracer "function_graph" uses
__lshrdi3() during the capturing of trace data. ftrace then attempts to
trace __lshrdi3() which leads to infinite recursion and a stack overflow.
Fix this by marking __lshrdi3() as notrace. Mark the other compiler
intrinsics as notrace in case the compiler decides to use them in the
ftrace path.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: <linux-mips@linux-mips.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <stable@vger.kernel.org> # 4.2.x-
Patchwork: https://patchwork.linux-mips.org/patch/13354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The Hardware page Table Walker (HTW) is being misconfigured on 64-bit
kernels. The PWSize.PS (pointer size) bit determines whether pointers
within directories are loaded as 32-bit or 64-bit addresses, but was
never being set to 1 for 64-bit kernels where the unsigned long in pgd_t
is 64-bits wide.
This actually reduces rather than improves performance when the HTW is
enabled on P6600 since the HTW is initiated lots, but walks are all
aborted due I think to bad intermediate pointers.
Since we were already taking the width of the PTEs into account by
setting PWSize.PTEW, which is the left shift applied to the page table
index *in addition to* the native pointer size, we also need to reduce
PTEW by 1 when PS=1. This is done by calculating PTEW based on the
relative size of pte_t compared to pgd_t.
Finally in order for the HTW to be used when PS=1, the appropriate
XK/XS/XU bits corresponding to the different 64-bit segments need to be
set in PWCtl. We enable only XU for now to enable walking for XUSeg.
Supporting walking for XKSeg would be a bit more involved so is left for
a future patch. It would either require the use of a per-CPU top level
base directory if supported by the HTW (a bit like pgd_current but with
a second entry pointing at swapper_pg_dir), or the HTW would prepend bit
63 of the address to the global directory index which doesn't really
match how we split user and kernel page directories.
Fixes: cab25bc7537b ("MIPS: Extend hardware table walking support to MIPS64")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add field definitions for some of the 64-bit specific Hardware page
Table Walker (HTW) register fields in PWSize and PWCtl, in preparation
for fixing the 64-bit HTW configuration.
Also print these fields out along with the others in print_htw_config().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Simplify the DSP instruction wrapper macros which use explicit encodings
for microMIPS and normal MIPS by using the new encoding macros and
removing duplication.
To me this makes it easier to read since it is much shorter, but it also
ensures .insn is used, preventing objdump disassembling the microMIPS
code as normal MIPS.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13314/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Hardcoded MIPS instruction encodings are provided for tlbinvf, mfhc0 &
mthc0 instructions, but microMIPS encodings are missing. I doubt any
microMIPS cores exist at present which support these instructions, but
the microMIPS encodings exist, and microMIPS cores may support them in
the future. Add the missing microMIPS encodings using the new macros.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13313/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
When the toolchain doesn't support MSA we encode MSA instructions
explicitly in assembly. Unfortunately we use .word for both MIPS and
microMIPS encodings which is wrong, since 32-bit microMIPS instructions
are made up from a pair of halfwords.
- The most significant halfword always comes first, so for little endian
builds the halves will be emitted in the wrong order.
- 32-bit alignment isn't guaranteed, so the assembler may insert a
16-bit nop instruction to pad the instruction stream to a 32-bit
boundary.
Use the new instruction encoding macros to encode microMIPS MSA
instructions correctly.
Fixes: d96cc3d1ec5d ("MIPS: Add microMIPS MSA support.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <Paul.Burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13312/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Toolchains may be used which support microMIPS but not VZ instructions
(i.e. binutis 2.22 & 2.23), so extend the explicitly encoded versions of
the guest COP0 register & guest TLB access macros to support microMIPS
encodings too, using the new macros.
This prevents non-microMIPS instructions being executed in microMIPS
mode during CPU probe on cores supporting VZ (e.g. M5150), which cause
reserved instruction exceptions early during boot.
Fixes: bad50d79255a ("MIPS: Fix VZ probe gas errors with binutils <2.24")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13311/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
