summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)AuthorFilesLines
2009-10-14[S390] hypfs: Use subcode 6 if subcode 7 is not availableMichael Holzheu1-1/+1
Hypfs never worked on systems that only provide D204 subcode 6. In these cases we nevertheless used subcode 7. With this fix, we use subcode 6, if it is available and the system does not provide subcode 7. Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2009-10-13Merge git://git.infradead.org/~dwmw2/iommu-2.6.32Linus Torvalds1-1/+1
* git://git.infradead.org/~dwmw2/iommu-2.6.32: x86: Move pci_iommu_init to rootfs_initcall() Run pci_apply_final_quirks() sooner. Mark pci_apply_final_quirks() __init rather than __devinit Rename pci_init() to pci_apply_final_quirks(), move it to quirks.c intel-iommu: Yet another BIOS workaround: Isoch DMAR unit with no TLB space intel-iommu: Decode (and ignore) RHSA entries intel-iommu: Make "Unknown DMAR structure" message more informative
2009-10-12ARM: force dcache flush if dcache_dirty bit setNitin Gupta1-6/+3
On ARM, update_mmu_cache() does dcache flush for a page only if it has a kernel mapping (page_mapping(page) != NULL). The correct behavior would be to force the flush based on dcache_dirty bit only. One of the cases where present logic would be a problem is when a RAM based block device[1] is used as a swap disk. In this case, we would have in-memory data corruption as shown in steps below: do_swap_page() { - Allocate a new page (if not already in swap cache) - Issue read from swap disk - Block driver issues flush_dcache_page() - flush_dcache_page() simply sets PG_dcache_dirty bit and does not actually issue a flush since this page has no user space mapping yet. - Now, if swap disk is almost full, this newly read page is removed from swap cache and corrsponding swap slot is freed. - Map this page anonymously in user space. - update_mmu_cache() - Since this page does not have kernel mapping (its not in page/swap cache and is mapped anonymously), it does not issue dcache flush even if dcache_dirty bit is set by flush_dcache_page() above. <user now gets stale data since dcache was never flushed> } Same problem exists on mips too. [1] example: - brd (RAM based block device) - ramzswap (RAM based compressed swap device) Signed-off-by: Nitin Gupta <ngupta@vflare.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-12x86: Move pci_iommu_init to rootfs_initcall()David Woodhouse1-1/+1
We want this to happen after the PCI quirks, which are now running at the very end of the fs_initcalls. This works around the BIOS problems which were originally addressed by commit db8be50c4307dac2b37305fc59c8dc0f978d09ea ('USB: Work around BIOS bugs by quiescing USB controllers earlier'), which was reverted in commit d93a8f829fe1d2f3002f2c6ddb553d12db420412. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-10-12Merge branch 'fix' of ↵Russell King354-5225/+2580
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6
2009-10-12[ARM] pxa: workaround errata #37 by not using half turbo switchingDennis O'Brien1-1/+1
PXA27x Errata #37 implies system will hang when switching into or out of half turbo (HT bit in CLKCFG) mode, workaround this by not using it. Signed-off-by: Dennis O'Brien <dennis.obrien@eqware.net> Cc: stable-2.6.31 <stable@kernel.org> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2009-10-12[ARM] pxa/csb726: adjust duplicate structure field initializationJulia Lawall1-1/+1
Currently the irq_type field of the csb726_lan_config structure is initialized twice. The value in the first case, SMSC911X_IRQ_POLARITY_ACTIVE_LOW, is normally stored in the irq_polarity field, so I have renamed the field in the first initialization to that. Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2009-10-12pci: increase alignment to make more space for hidden codeYinghai Lu1-2/+2
As reported in http://bugzilla.kernel.org/show_bug.cgi?id=13940 on some system when acpi are enabled, acpi clears some BAR for some devices without reason, and kernel will need to allocate devices for them. It then apparently hits some undocumented resource conflict, resulting in non-working devices. Try to increase alignment to get more safe range for unassigned devices. Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-11Merge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6Linus Torvalds17-51/+221
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (21 commits) [S390] dasd: fix race condition in resume code [S390] Add EX_TABLE for addressing exception in usercopy functions. [S390] 64-bit register support for 31-bit processes [S390] hibernate: Use correct place for CPU address in lowcore [S390] pm: ignore time spend in suspended state [S390] zcrypt: Improve some comments [S390] zcrypt: Fix sparse warning. [S390] perf_counter: fix vdso detection [S390] ftrace: drop nmi protection [S390] compat: fix truncate system call wrapper [S390] Provide arch specific mdelay implementation. [S390] Fix enabled udelay for short delays. [S390] cio: allow setting boxed devices offline [S390] cio: make not operational handling consistent [S390] cio: make disconnected handling consistent [S390] Fix memory leak in /proc/cio_ignore [S390] cio: channel path memory leak [S390] module: fix memory leak in s390 module loader [S390] Enable kmemleak on s390. [S390] 3270 console build fix ...
2009-10-11headers: remove sched.h from interrupt.hAlexey Dobriyan12-0/+12
After m68k's task_thread_info() doesn't refer to current, it's possible to remove sched.h from interrupt.h and not break m68k! Many thanks to Heiko Carstens for allowing this. Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
2009-10-11ARM: Add kmap_atomic type debuggingRussell King1-0/+2
Seemingly this support was missed when highmem was added, so DEBUG_HIGHMEM wouldn't have checked the kmap_atomic type. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-11ARM: boolean bit testingJohannes Weiner1-3/+3
Bit testing (test, testset, testclear, testchange) for bit numbers known at compile time returns a word with the tested-for bit set. Change it to return a true boolean value so to make it consistent with the out-of-line path and all the other bitops implementations. Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-11ARM: update die() outputRussell King1-2/+3
Make die() better match x86: - add printing of the last accessed sysfs file - ensure console_verbose() is called under the lock - ensure we panic outside of oops_exit() Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-11ARM: Dump code/mem oops lines with the appropriate log levelRussell King1-16/+17
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-11ARM: Dump memory and backtrace as one printk per lineRussell King1-19/+23
dump_mem and dump_backtrace were both using multiple printk statements to print each line. With DEBUG_LL enabled, this causes OOPS to become very difficult to read. Solve this by only using one printk per line. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-10ARM: 5756/1: ep93xx: introduce clk parentHartley Sweeten1-47/+119
The clock generation system in the ep93xx uses two external oscillator's and two internal PLLs to derive all the internal clocks. Many of these internal clocks can be stopped to save power. This introduces a "parent" hierarchy for the clocks so that the users count can be correctly tracked for power management. The "parent" for the video clock can either be one of the PLL outputs or the external oscillator. In order to correctly track the "parent" for the video clock calc_clk_div() needed to be modified. It now returns an error code if the desired rate cannot be generated. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Ryan Mallon <ryan@bluewatersys.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-10ARM: 5754/1: ep93xx: update i2c supportHartley Sweeten4-16/+51
Update the ep93xx i2c support: 1) The platform init code passes the configuration data for the i2c-gpio driver. This allows any gpio pin do be used for the sda and scl pins. It also allows the platform to specify the udelay and timeout. 2) Program the gpio configuration register to enable/disable the open drain drivers. Note that this really only works if the sda and scl pins are set to EP93XX_GPIO_LINE_EEDAT and EP93XX_GPIO_LINE_EECLK. 3) Update the edb93xx.c platform init to use the new support. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Ryan Mallon <ryan@bluewatersys.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-10ARM: 5753/1: ep93xx: remove old EP93XX_GPIO_* definesHartley Sweeten1-12/+0
Most of the EP93XX_GPIO_*_INT_* register defines in ep93xx-regs.h not required due to how the ep93xx core and gpiolib support handle gpio interrupts. Remove the defines to prevent future confusion. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Ryan Mallon <ryan@bluewatersys.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-10Merge branch 'for-linus' of ↵Linus Torvalds1-39/+39
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: i8042 - print debug data when testing AUX IRQ delivery Input: libps2 - fix dependancy on i8042 Input: fix rx51 board keymap Input: ad7879 - pass up error codes from probe functions Input: xpad - add BigBen Interactive XBOX 360 Controller Input: rotary_encoder - fix relative axis support Input: sparkspkr - move remove() functions to .devexit.text Input: wistron_btns - add DMI entry for Medion WIM2030 laptop
2009-10-10Merge branch 'for-linus' of ↵Linus Torvalds250-4717/+1078
git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: Blackfin: convert to GENERIC_HARDIRQS_NO__DO_IRQ Blackfin: drop all simple-gpio board resources Blackfin: fix framebuffer mmap bug for nommu Blackfin: includecheck fix: mach-bf548, ezkit.c Blackfin: drop cs_change_per_word setting Blackfin: bf533-ezkit: convert to physmap/jedec_probe Blackfin: convert adv7393 resources to new i2c framework Blackfin: fix missed cache config renames Blackfin: cplbinfo: drop d_path() hacks Blackfin: asm/irq.h: pull in mach/anomaly.h for anomaly defines Blackfin: BF51x: add PTP MMR defines Blackfin: mass clean up of copyright/licensing info Blackfin: convert to use arch_gettimeoffset()
2009-10-09Merge branch 'sh/for-2.6.32' of ↵Linus Torvalds12-19/+106
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6 * 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: sh: Don't allocate smaller sized mappings on every iteration sh: Try PMB mapping based on physical address, not mapping size sh: Plug PMB alloc memory leak sh: Sprinkle __uses_jump_to_uncached sh: enable sleep state LEDs on Ecovec24 usb: r8a66597-udc unaligned fifo fix sh: mach-ecovec24: Document DS2 switch settings. sh: Build fix: export __movmem sh: Disable unaligned kernel access printks by default. sh: mach-ecovec24: modify 1st MTD area to read only sh: mach-ecovec24: Add TouchScreen support sh: magicpanelr2 and dreamcast can use the generic I/O base. sh: Don't enable interrupts in the page fault path sh: Set the default I/O port base to P2SEG. sh: Handle ioport_map() cases for >= P1SEG addresses.
2009-10-09sh: Don't allocate smaller sized mappings on every iterationMatt Fleming1-0/+7
Currently, we've got the less than ideal situation where if we need to allocate a 256MB mapping we'll allocate four entries like so, entry 1: 128MB entry 2: 64MB entry 3: 16MB entry 4: 16MB This is because as we execute the loop in pmb_remap() we will progressively try mapping the remaining address space with smaller and smaller sizes. This isn't good because the size we use on one iteration may be the perfect size to use on the next iteration, for instance when the initial size is divisible by one of the PMB mapping sizes. With this patch, we now only need two entries in the PMB to map 256MB of address space, entry 1: 128MB entry 2: 128MB Signed-off-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-10-09sh: Try PMB mapping based on physical address, not mapping sizeMatt Fleming1-1/+1
We should favour PMB mappings when the physical address cannot be reached with 29-bits. Signed-off-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-10-09sh: Plug PMB alloc memory leakMatt Fleming1-6/+24
If we fail to allocate a PMB entry in pmb_remap() we must remember to clear and free any PMB entries that we may have previously allocated, e.g. if we were allocating a multiple entry mapping. Signed-off-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-10-09sh: Sprinkle __uses_jump_to_uncachedMatt Fleming2-3/+3
Fix some callers of jump_to_uncached() and back_to_cached() that were not annotated with __uses_jump_to_uncached. Signed-off-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-10-09sh: enable sleep state LEDs on Ecovec24Magnus Damm1-0/+5
Extend the ecovec24 board code to enable Power Management LEDs showing the current sh7724 sleep state. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-10-08Merge branch 'x86-fixes-for-linus' of ↵Linus Torvalds4-28/+51
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86, pci: Correct spelling in a comment x86: Simplify bound checks in the MTRR code x86: EDAC: carve out AMD MCE decoding logic initcalls: Add early_initcall() for modules x86: EDAC: MCE: Fix MCE decoding callback logic
2009-10-08Merge branch 'sparc-perf-events-fixes-for-linus' of ↵Linus Torvalds1-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'sparc-perf-events-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: mm, perf_event: Make vmalloc_user() align base kernel virtual address to SHMLBA perf_event: Provide vmalloc() based mmap() backing
2009-10-08Merge branch 'timers-fixes-for-linus' of ↵Linus Torvalds2-0/+3
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86, timers: Check for pending timers after (device) interrupts NOHZ: update idle state also when NOHZ is inactive
2009-10-08Merge branch 'omap-fixes-for-linus' of ↵Linus Torvalds8-123/+193
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: omapfb: Blizzard: constify register address tables omapfb: Blizzard: fix pointer to be const omapfb: Condition mutex acquisition omap: iovmm: Add missing mutex_unlock omap: iovmm: Fix incorrect spelling omap: SRAM: flush the right address after memcpy in omap_sram_push omap: Lock DPLL5 at boot omap: Fix incorrect 730 vs 850 detection OMAP3: PM: introduce a new powerdomain walk helper OMAP3: PM: Enable GPIO module-level wakeups OMAP3: PM: USBHOST: clear wakeup events on both hosts OMAP3: PM: PRCM interrupt: only handle selected PRCM interrupts OMAP3: PM: PRCM interrupt: check MPUGRPSEL register OMAP3: PM: Prevent hang in prcm_interrupt_handler
2009-10-08x86, timers: Check for pending timers after (device) interruptsArjan van de Ven2-0/+3
Now that range timers and deferred timers are common, I found a problem with these using the "perf timechart" tool. Frans Pop also reported high scheduler latencies via LatencyTop, when using iwlagn. It turns out that on x86, these two 'opportunistic' timers only get checked when another "real" timer happens. These opportunistic timers have the objective to save power by hitchhiking on other wakeups, as to avoid CPU wakeups by themselves as much as possible. The change in this patch runs this check not only at timer interrupts, but at all (device) interrupts. The effect is that: 1) the deferred timers/range timers get delayed less 2) the range timers cause less wakeups by themselves because the percentage of hitchhiking on existing wakeup events goes up. I've verified the working of the patch using "perf timechart", the original exposed bug is gone with this patch. Frans also reported success - the latencies are now down in the expected ~10 msec range. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Tested-by: Frans Pop <elendil@planet.nl> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Mike Galbraith <efault@gmx.de> LKML-Reference: <20091008064041.67219b13@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-10-08Merge branch 'fixes' of ↵Linus Torvalds15-80/+126
git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6 * 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6: agp: parisc-agp.c - use correct page_mask function parisc: Fix linker script breakage. parisc: convert to asm-generic/hardirq.h parisc: Make THREAD_SIZE available to assembly files and linker scripts. parisc: correct use of SHF_ALLOC parisc: rename parisc's vmalloc_start to parisc_vmalloc_start parisc: add me to Maintainers parisc: includecheck fix: signal.c parisc: HAVE_ARCH_TRACEHOOK parisc: add skeleton syscall.h parisc: stop using task->ptrace for {single,block}step flags parisc: split syscall_trace into two halves parisc: add missing TI_TASK macro in syscall.S parisc: tracehook_signal_handler parisc: tracehook_report_syscall
2009-10-08Blackfin: convert to GENERIC_HARDIRQS_NO__DO_IRQMichael Hennerich1-0/+3
Blackfin already sets proper flow handlers on all IRQs, and we don't rely on __do_IRQ, therefore we can simply select GENERIC_HARDIRQS_NO__DO_IRQ. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-08Blackfin: drop all simple-gpio board resourcesMike Frysinger17-255/+0
The simple-gpio has been replaced by the gpio sysfs interface, so drop the unused simple-gpio resources from all Blackfin boards. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-08Blackfin: fix framebuffer mmap bug for nommuThomas Chou2-0/+17
The patch added a special get_unmapped_area for framebuffer which was hooked to the file ops in drivers/video/fbmem.c. This is needed since v2.6.29-rc1 where nommu vma management was updated, and mmap of framebuffer caused kernel BUG panic. You may turn on "Debug the global anon/private NOMMU mapping region tree" config to such message. As Documentation/nommu-mmap.txt said, "To provide shareable character device support, a driver must provide a file->f_op->get_unmapped_area() operation. The mmap() routines will call this to get a proposed address for the mapping." With this change, user space should call mmap for framebuffer using shared map. Or it can try shared map first, then private map if failed. This shared map usage is now consistent between mmu and nommu. The sys_ file may not be a good place for this patch. But there is a similar one for sparc. I tested a similar patch on nios2nommu, though I don't have a blackfin board to test. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Graf Yang <graf.yang@analog.com> Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-08Blackfin: includecheck fix: mach-bf548, ezkit.cJaswinder Singh Rajput1-1/+0
Fix the following 'make includecheck' warning: arch/blackfin/mach-bf548/boards/ezkit.c: linux/input.h is included more than once. Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-08Blackfin: drop cs_change_per_word settingMike Frysinger5-8/+0
Structs get initialized to 0 already, and we want to punt this field, so scrub it from all of our boards. Reported-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-08Blackfin: bf533-ezkit: convert to physmap/jedec_probeMike Frysinger1-25/+41
Now that the common jedec_probe supports the ST PSD4256G6V, no need to use the custom stm_flash driver. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-08Blackfin: convert adv7393 resources to new i2c frameworkMichael Hennerich5-50/+31
Now that the driver has been updated, convert the board resources to the new i2c framework for managing slaves. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-07ARM: 5729/1: ep93xx: define EP93XX_*_PHYS_BASE with macrosHartley Sweeten1-8/+10
Change the #define's for the EP93XX_*_PHYS_BASE addresses to use macros for easier readability. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Ryan Mallon <ryan@bluewatersys.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-07ARM: 5751/1: ep93xx/micro9: Add Micro9-SlimHubert Feurstein2-1/+23
Add Contec Micro9-Slim support Cc: Ryan Mallon <ryan@bluewatersys.com> Requires: 5750/1 Signed-off-by: Hubert Feurstein <hubert.feurstein@contec.at> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-07ARM: 5750/1: ep93xx/micro9: Update platform codeHubert Feurstein3-58/+75
Update Contec Micro9 platform code Cc: Ryan Mallon <ryan@bluewatersys.com> Requires: 5749/1 Signed-off-by: Hubert Feurstein <hubert.feurstein@contec.at> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-07ARM: 5749/1: ep93xx/micro9: Update maintainerHubert Feurstein1-4/+6
Update Contec Micro9 maintainer and add entry in MAINTAINERS Cc: Ryan Mallon <ryan@bluewatersys.com> Requires: 5744/1 Signed-off-by: Hubert Feurstein <hubert.feurstein@contec.at> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Manfred Gruber <m.gruber@tirol.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-07ARM: 5752/1: SA1100: fix building of h3100Dmitry Artamonow1-0/+1
Both iPaqs h3100 and h3600 currently share the same source file - h3600.c But Makefile builds it only if CONFIG_SA1100_H3600 selected, so selecting just CONFIG_SA1100_H3100 results in "no machine record defined" message and aborted compilation. Fix it. Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-07ARM: 5748/1: bcmring: fix build warning messagesLeo Chen2-3/+3
Fix the warning messages during kernel build for bcmring. Signed-off-by: Leo Hao Chen <leochen@broadcom.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-07ARM: 5747/1: Fix the start_pg value in free_memmap()Catalin Marinas1-1/+1
If sparsemem is enabled, the start_pfn passed to the free_memmap() function corresponds to an area of memory not known to the kernel and pfn_to_page returns a wrong value. The (start_pfn - 1), however, is known to the kernel. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-07ARM: 5746/1: Handle possible translation errors in ARMv6/v7 coherent_user_rangeCatalin Marinas2-4/+35
This is needed because applications using the sys_cacheflush system call can pass a memory range which isn't mapped yet even though the corresponding vma is valid. The patch also adds unwinding annotations for correct backtraces from the coherent_user_range() functions. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-07ARM: 5745/1: Change ep93xx gpio_irq static inlines to macrosHartley Sweeten1-12/+4
From: Ryan Mallon <ryan@bluewatersys.com> Change the gpio_to_irq and irq_to_gpio static inline functions to macros so that they can be used in variable initialisers. Signed-off-by: Ryan Mallon <ryan@bluewatersys.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-07ARM: 5744/1: ep93xx: add remaining phys offset selectionsHartley Sweeten3-2/+35
This adds the missing Kconfig options for the first SDRAM bank address on ep93xx boards. Cc: Hubert Feurstein <(address hidden)> Signed-off-by: H Hartley Sweeten <(address hidden)> Acked-by: Ryan Mallon <(address hidden)> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-10-07Blackfin: fix missed cache config renamesGraf Yang1-2/+2
Looks like the big Kconfig cache split/rename missed one spot in the SMP cache lock headers. Signed-off-by: Graf Yang <graf.yang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>