| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add a helper to finish/complete the handling of a guest page, e.g. to
mark the pages accessed and put any held references. In the near
future, this will allow improving the logic without having to copy+paste
changes into all page fault paths. And in the less near future, will
allow sharing the "finish" API across all architectures.
No functional change intended.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-41-seanjc@google.com>
|
|
Deduplicate the prefetching code for indirect and direct MMUs. The core
logic is the same, the only difference is that indirect MMUs need to
prefetch SPTEs one-at-a-time, as contiguous guest virtual addresses aren't
guaranteed to yield contiguous guest physical addresses.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-40-seanjc@google.com>
|
|
Use kvm_release_page_clean() to put prefeteched pages instead of calling
put_page() directly. This will allow de-duplicating the prefetch code
between indirect and direct MMUs.
Note, there's a small functional change as kvm_release_page_clean() marks
the page/folio as accessed. While it's not strictly guaranteed that the
guest will access the page, KVM won't intercept guest accesses, i.e. won't
mark the page accessed if it _is_ accessed by the guest (unless A/D bits
are disabled, but running without A/D bits is effectively limited to
pre-HSW Intel CPUs).
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-39-seanjc@google.com>
|
|
Prefix x86's faultin_pfn helpers with "mmu" so that the mmu-less names can
be used by common KVM for similar APIs.
No functional change intended.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-38-seanjc@google.com>
|
|
Drop the gfn_to_page() lookup when installing KVM's internal memslot for
the APIC access page, as KVM doesn't need to immediately fault-in the page
now that the page isn't pinned. In the extremely unlikely event the
kernel can't allocate a 4KiB page, KVM can just as easily return -EFAULT
on the future page fault.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-37-seanjc@google.com>
|
|
Now that all kvm_vcpu_{,un}map() users pass "true" for @dirty, have them
pass "true" as a @writable param to kvm_vcpu_map(), and thus create a
read-only mapping when possible.
Note, creating read-only mappings can be theoretically slower, as they
don't play nice with fast GUP due to the need to break CoW before mapping
the underlying PFN. But practically speaking, creating a mapping isn't
a super hot path, and getting a writable mapping for reading is weird and
confusing.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-34-seanjc@google.com>
|
|
Mark the APIC access page as dirty when unmapping it from KVM. The fact
that the page _shouldn't_ be written doesn't guarantee the page _won't_ be
written. And while the contents are likely irrelevant, the values _are_
visible to the guest, i.e. dropping writes would be visible to the guest
(though obviously highly unlikely to be problematic in practice).
Marking the map dirty will allow specifying the write vs. read-only when
*mapping* the memory, which in turn will allow creating read-only maps.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-33-seanjc@google.com>
|
|
Add a helper to dedup unmapping the vmcs12 pages. This will reduce the
amount of churn when a future patch refactors the kvm_vcpu_unmap() API.
No functional change intended.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-26-seanjc@google.com>
|
|
Remove vcpu_vmx.msr_bitmap_map and instead use an on-stack structure in
the one function that uses the map, nested_vmx_prepare_msr_bitmap().
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-25-seanjc@google.com>
|
|
Remove the explicit evmptr12 validity check when deciding whether or not
to unmap the eVMCS pointer, and instead rely on kvm_vcpu_unmap() to play
nice with a NULL map->hva, i.e. to do nothing if the map is invalid.
Note, vmx->nested.hv_evmcs_map is zero-allocated along with the rest of
vcpu_vmx, i.e. the map starts out invalid/NULL.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-24-seanjc@google.com>
|
|
Drop @hva from __gfn_to_pfn_memslot() now that all callers pass NULL.
No functional change intended.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-19-seanjc@google.com>
|
|
Remove kvm_page_fault.hva as it is never read, only written. This will
allow removing the @hva param from __gfn_to_pfn_memslot().
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-18-seanjc@google.com>
|
|
Add a pfn error code to communicate that hva_to_pfn() failed because I/O
was needed and disallowed, and convert @async to a constant @no_wait
boolean. This will allow eliminating the @no_wait param by having callers
pass in FOLL_NOWAIT along with other FOLL_* flags.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: David Stevens <stevensd@chromium.org>
Co-developed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-17-seanjc@google.com>
|
|
Drop @atomic from the myriad "to_pfn" APIs now that all callers pass
"false", and remove a comment blurb about KVM running only the "GUP fast"
part in atomic context.
No functional change intended.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-13-seanjc@google.com>
|
|
Rename gfn_to_page_many_atomic() to kvm_prefetch_pages() to try and
communicate its true purpose, as the "atomic" aspect is essentially a
side effect of the fact that x86 uses the API while holding mmu_lock.
E.g. even if mmu_lock weren't held, KVM wouldn't want to fault-in pages,
as the goal is to opportunistically grab surrounding pages that have
already been accessed and/or dirtied by the host, and to do so quickly.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-12-seanjc@google.com>
|
|
Use gfn_to_page_many_atomic() instead of gfn_to_pfn_memslot_atomic() when
prefetching indirect PTEs (direct_pte_prefetch_many() already uses the
"to page" APIS). Functionally, the two are subtly equivalent, as the "to
pfn" API short-circuits hva_to_pfn() if hva_to_pfn_fast() fails, i.e. is
just a wrapper for get_user_page_fast_only()/get_user_pages_fast_only().
Switching to the "to page" API will allow dropping the @atomic parameter
from the entire hva_to_pfn() callchain.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-11-seanjc@google.com>
|
|
Now that KVM doesn't clobber Accessed bits of shadow-present SPTEs,
e.g. when prefetching, mark folios as accessed only when zapping leaf
SPTEs, which is a rough heuristic for "only in response to an mmu_notifier
invalidation". Page aging and LRUs are tolerant of false negatives, i.e.
KVM doesn't need to be precise for correctness, and re-marking folios as
accessed when zapping entire roots or when zapping collapsible SPTEs is
expensive and adds very little value.
E.g. when a VM is dying, all of its memory is being freed; marking folios
accessed at that time provides no known value. Similarly, because KVM
marks folios as accessed when creating SPTEs, marking all folios as
accessed when userspace happens to delete a memslot doesn't add value.
The folio was marked access when the old SPTE was created, and will be
marked accessed yet again if a vCPU accesses the pfn again after reloading
a new root. Zapping collapsible SPTEs is a similar story; marking folios
accessed just because userspace disable dirty logging is a side effect of
KVM behavior, not a deliberate goal.
As an intermediate step, a.k.a. bisection point, towards *never* marking
folios accessed when dropping SPTEs, mark folios accessed when the primary
MMU might be invalidating mappings, as such zappings are not KVM initiated,
i.e. might actually be related to page aging and LRU activity.
Note, x86 is the only KVM architecture that "double dips"; every other
arch marks pfns as accessed only when mapping into the guest, not when
mapping into the guest _and_ when removing from the guest.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-10-seanjc@google.com>
|
|
Mark pages/folios dirty when creating SPTEs to map PFNs into the guest,
not when zapping or modifying SPTEs, as marking folios dirty when zapping
or modifying SPTEs can be extremely inefficient. E.g. when KVM is zapping
collapsible SPTEs to reconstitute a hugepage after disbling dirty logging,
KVM will mark every 4KiB pfn as dirty, even though _at least_ 512 pfns are
guaranteed to be in a single folio (the SPTE couldn't potentially be huge
if that weren't the case). The problem only becomes worse for 1GiB
HugeTLB pages, as KVM can mark a single folio dirty 512*512 times.
Marking a folio dirty when mapping is functionally safe as KVM drops all
relevant SPTEs in response to an mmu_notifier invalidation, i.e. ensures
that the guest can't dirty a folio after access has been removed.
And because KVM already marks folios dirty when zapping/modifying SPTEs
for KVM reasons, i.e. not in response to an mmu_notifier invalidation,
there is no danger of "prematurely" marking a folio dirty. E.g. if a
filesystems cleans a folio without first removing write access, then there
already exists races where KVM could mark a folio dirty before remote TLBs
are flushed, i.e. before guest writes are guaranteed to stop. Furthermore,
x86 is literally the only architecture that marks folios dirty on the
backend; every other KVM architecture marks folios dirty at map time.
x86's unique behavior likely stems from the fact that x86's MMU predates
mmu_notifiers. Long, long ago, before mmu_notifiers were added, marking
pages dirty when zapping SPTEs was logical, and perhaps even necessary, as
KVM held references to pages, i.e. kept a page's refcount elevated while
the page was mapped into the guest. At the time, KVM's rmap_remove()
simply did:
if (is_writeble_pte(*spte))
kvm_release_pfn_dirty(pfn);
else
kvm_release_pfn_clean(pfn);
i.e. dropped the refcount and marked the page dirty at the same time.
After mmu_notifiers were introduced, commit acb66dd051d0 ("KVM: MMU:
don't hold pagecount reference for mapped sptes pages") removed the
refcount logic, but kept the dirty logic, i.e. converted the above to:
if (is_writeble_pte(*spte))
kvm_release_pfn_dirty(pfn);
And for KVM x86, that's essentially how things have stayed over the last
~15 years, without anyone revisiting *why* KVM marks pages/folios dirty at
zap/modification time, e.g. the behavior was blindly carried forward to
the TDP MMU.
Practically speaking, the only downside to marking a folio dirty during
mapping is that KVM could trigger writeback of memory that was never
actually written. Except that can't actually happen if KVM marks folios
dirty if and only if a writable SPTE is created (as done here), because
KVM always marks writable SPTEs as dirty during make_spte(). See commit
9b51a63024bd ("KVM: MMU: Explicitly set D-bit for writable spte."), circa
2015.
Note, KVM's access tracking logic for prefetched SPTEs is a bit odd. If a
guest PTE is dirty and writable, KVM will create a writable SPTE, but then
mark the SPTE for access tracking. Which isn't wrong, just a bit odd, as
it results in _more_ precise dirty tracking for MMUs _without_ A/D bits.
To keep things simple, mark the folio dirty before access tracking comes
into play, as an access-tracked SPTE can be restored in the fast page
fault path, i.e. without holding mmu_lock. While writing SPTEs and
accessing memslots outside of mmu_lock is safe, marking a folio dirty is
not. E.g. if the fast path gets interrupted _just_ after setting a SPTE,
the primary MMU could theoretically invalidate and free a folio before KVM
marks it dirty. Unlike the shadow MMU, which waits for CPUs to respond to
an IPI, the TDP MMU only guarantees the page tables themselves won't be
freed (via RCU).
Opportunistically update a few stale comments.
Cc: David Matlack <dmatlack@google.com>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-9-seanjc@google.com>
|
|
Set the Accessed bit when making a "new" SPTE during SPTE synchronization,
as _clearing_ the Accessed bit is counter-productive, and even if the
Accessed bit wasn't set in the old SPTE, odds are very good the guest will
access the page in the near future, as the most common case where KVM
synchronizes a shadow-present SPTE is when the guest is making the gPTE
read-only for Copy-on-Write (CoW).
Preserving the Accessed bit will allow dropping the logic that propagates
the Accessed bit to the underlying struct page when overwriting an existing
SPTE, without undue risk of regressing page aging.
Note, KVM's current behavior is very deliberate, as SPTE synchronization
was the only "speculative" access type as of commit 947da5383069 ("KVM:
MMU: Set the accessed bit on non-speculative shadow ptes").
But, much has changed since 2008, and more changes are on the horizon.
Spurious clearing of the Accessed (and Dirty) was mitigated by commit
e6722d9211b2 ("KVM: x86/mmu: Reduce the update to the spte in
FNAME(sync_spte)"), which changed FNAME(sync_spte) to only overwrite SPTEs
if the protections are actually changing. I.e. KVM is already preserving
Accessed information for SPTEs that aren't dropping protections.
And with the aforementioned future change to NOT mark the page/folio as
accessed, KVM's SPTEs will become the "source of truth" so to speak, in
which case clearing the Accessed bit outside of page aging becomes very
undesirable.
Suggested-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-8-seanjc@google.com>
|
|
Invert the polarity of "can_unsync" and rename the parameter to
"synchronizing" to allow a future change to set the Accessed bit if KVM
is synchronizing an existing SPTE. Querying "can_unsync" in that case is
nonsensical, as the fact that KVM can't unsync SPTEs doesn't provide any
justification for setting the Accessed bit.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-7-seanjc@google.com>
|
|
Treat attempts to prefetch/prefault MMU SPTEs as spurious if there's an
existing shadow-present SPTE, as overwriting a SPTE that may have been
create by a "real" fault is at best confusing, and at worst potentially
harmful. E.g. mmu_try_to_unsync_pages() doesn't unsync when prefetching,
which creates a scenario where KVM could try to replace a Writable SPTE
with a !Writable SPTE, as sp->unsync is checked prior to acquiring
mmu_unsync_pages_lock.
Note, this applies to three of the four flavors of "prefetch" in KVM:
- KVM_PRE_FAULT_MEMORY
- Async #PF (host or PV)
- Prefetching
The fourth flavor, SPTE synchronization, i.e. FNAME(sync_spte), _only_
overwrites shadow-present SPTEs when calling make_spte(). But SPTE
synchronization specifically uses mmu_spte_update(), and so naturally
avoids the @prefetch check in mmu_set_spte().
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-6-seanjc@google.com>
|
|
Apply make_spte()'s optimization to skip trying to unsync shadow pages if
and only if the old SPTE was a leaf SPTE, as non-leaf SPTEs in direct MMUs
are always writable, i.e. could trigger a false positive and incorrectly
lead to KVM creating a SPTE without write-protecting or marking shadow
pages unsync.
This bug only affects the TDP MMU, as the shadow MMU only overwrites a
shadow-present SPTE when synchronizing SPTEs (and only 4KiB SPTEs can be
unsync). Specifically, mmu_set_spte() drops any non-leaf SPTEs *before*
calling make_spte(), whereas the TDP MMU can do a direct replacement of a
page table with the leaf SPTE.
Opportunistically update the comment to explain why skipping the unsync
stuff is safe, as opposed to simply saying "it's someone else's problem".
Cc: stable@vger.kernel.org
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-5-seanjc@google.com>
|
|
Remove KVM_ERR_PTR_BAD_PAGE and instead return NULL, as "bad page" is just
a leftover bit of weirdness from days of old when KVM stuffed a "bad" page
into the guest instead of actually handling missing pages. See commit
cea7bb21280e ("KVM: MMU: Make gfn_to_page() always safe").
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20241010182427.1434605-2-seanjc@google.com>
|
|
Ignore nCR3[4:0] when loading PDPTEs from memory for nested SVM, as bits
4:0 of CR3 are ignored when PAE paging is used, and thus VMRUN doesn't
enforce 32-byte alignment of nCR3.
In the absolute worst case scenario, failure to ignore bits 4:0 can result
in an out-of-bounds read, e.g. if the target page is at the end of a
memslot, and the VMM isn't using guard pages.
Per the APM:
The CR3 register points to the base address of the page-directory-pointer
table. The page-directory-pointer table is aligned on a 32-byte boundary,
with the low 5 address bits 4:0 assumed to be 0.
And the SDM's much more explicit:
4:0 Ignored
Note, KVM gets this right when loading PDPTRs, it's only the nSVM flow
that is broken.
Fixes: e4e517b4be01 ("KVM: MMU: Do not unconditionally read PDPTE from guest memory")
Reported-by: Kirk Swidowski <swidowski@google.com>
Cc: Andy Nguyen <theflow@google.com>
Cc: 3pvd <3pvd@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20241009140838.1036226-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Reset the segment cache after segment initialization in vmx_vcpu_reset()
to harden KVM against caching stale/uninitialized data. Without the
recent fix to bypass the cache in kvm_arch_vcpu_put(), the following
scenario is possible:
- vCPU is just created, and the vCPU thread is preempted before
SS.AR_BYTES is written in vmx_vcpu_reset().
- When scheduling out the vCPU task, kvm_arch_vcpu_in_kernel() =>
vmx_get_cpl() reads and caches '0' for SS.AR_BYTES.
- vmx_vcpu_reset() => seg_setup() configures SS.AR_BYTES, but doesn't
invoke vmx_segment_cache_clear() to invalidate the cache.
As a result, KVM retains a stale value in the cache, which can be read,
e.g. via KVM_GET_SREGS. Usually this is not a problem because the VMX
segment cache is reset on each VM-Exit, but if the userspace VMM (e.g KVM
selftests) reads and writes system registers just after the vCPU was
created, _without_ modifying SS.AR_BYTES, userspace will write back the
stale '0' value and ultimately will trigger a VM-Entry failure due to
incorrect SS segment type.
Invalidating the cache after writing the VMCS doesn't address the general
issue of cache accesses from IRQ context being unsafe, but it does prevent
KVM from clobbering the VMCS, i.e. mitigates the harm done _if_ KVM has a
bug that results in an unsafe cache access.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Fixes: 2fb92db1ec08 ("KVM: VMX: Cache vmcs segment fields")
[sean: rework changelog to account for previous patch]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20241009175002.1118178-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add a lockdep assertion in kvm_unmap_gfn_range() to ensure that either
mmu_invalidate_in_progress is elevated, or that the range is being zapped
due to memslot removal (loosely detected by slots_lock being held).
Zapping SPTEs without mmu_invalidate_{in_progress,seq} protection is unsafe
as KVM's page fault path snapshots state before acquiring mmu_lock, and
thus can create SPTEs with stale information if vCPUs aren't forced to
retry faults (due to seeing an in-progress or past MMU invalidation).
Memslot removal is a special case, as the memslot is retrieved outside of
mmu_invalidate_seq, i.e. doesn't use the "standard" protections, and
instead relies on SRCU synchronization to ensure any in-flight page faults
are fully resolved before zapping SPTEs.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20241009192345.1148353-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When performing a targeted zap on memslot removal, zap only MMU pages that
shadow guest PTEs, as zapping all SPs that "match" the gfn is inexact and
unnecessary. Furthermore, for_each_gfn_valid_sp() arguably shouldn't
exist, because it doesn't do what most people would it expect it to do.
The "round gfn for level" adjustment that is done for direct SPs (no gPTE)
means that the exact gfn comparison will not get a match, even when a SP
does "cover" a gfn, or was even created specifically for a gfn.
For memslot deletion specifically, KVM's behavior will vary significantly
based on the size and alignment of a memslot, and in weird ways. E.g. for
a 4KiB memslot, KVM will zap more SPs if the slot is 1GiB aligned than if
it's only 4KiB aligned. And as described below, zapping SPs in the
aligned case overzaps for direct MMUs, as odds are good the upper-level
SPs are serving other memslots.
To iterate over all potentially-relevant gfns, KVM would need to make a
pass over the hash table for each level, with the gfn used for lookup
rounded for said level. And then check that the SP is of the correct
level, too, e.g. to avoid over-zapping.
But even then, KVM would massively overzap, as processing every level is
all but guaranteed to zap SPs that serve other memslots, especially if the
memslot being removed is relatively small. KVM could mitigate that issue
by processing only levels that can be possible guest huge pages, i.e. are
less likely to be re-used for other memslot, but while somewhat logical,
that's quite arbitrary and would be a bit of a mess to implement.
So, zap only SPs with gPTEs, as the resulting behavior is easy to describe,
is predictable, and is explicitly minimal, i.e. KVM only zaps SPs that
absolutely must be zapped.
Cc: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Tested-by: Yan Zhao <yan.y.zhao@intel.com>
Message-ID: <20241009192345.1148353-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.12, take #1
- Fix pKVM error path on init, making sure we do not change critical
system registers as we're about to fail
- Make sure that the host's vector length is at capped by a value
common to all CPUs
- Fix kvm_has_feat*() handling of "negative" features, as the current
code is pretty broken
- Promote Joey to the status of official reviewer, while James steps
down -- hopefully only temporarly
|
|
kvm.ko is nothing but library code shared by kvm-intel.ko and kvm-amd.ko.
It provides no functionality on its own and it is unnecessary unless one
of the vendor-specific module is compiled. In particular, /dev/kvm is
not created until one of kvm-intel.ko or kvm-amd.ko is loaded.
Use CONFIG_KVM to decide if it is built-in or a module, but use the
vendor-specific modules for the actual decision on whether to build it.
This also fixes a build failure when CONFIG_KVM_INTEL and CONFIG_KVM_AMD
are both disabled. The cpu_emergency_register_virt_callback() function
is called from kvm.ko, but it is only defined if at least one of
CONFIG_KVM_INTEL and CONFIG_KVM_AMD is provided.
Fixes: 590b09b1d88e ("KVM: x86: Register "emergency disable" callbacks when virt is enabled")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
As was tried in commit 4e103134b862 ("KVM: x86/mmu: Zap only the relevant
pages when removing a memslot"), all shadow pages, i.e. non-leaf SPTEs,
need to be zapped. All of the accounting for a shadow page is tied to the
memslot, i.e. the shadow page holds a reference to the memslot, for all
intents and purposes. Deleting the memslot without removing all relevant
shadow pages, as is done when KVM_X86_QUIRK_SLOT_ZAP_ALL is disabled,
results in NULL pointer derefs when tearing down the VM.
Reintroduce from that commit the code that walks the whole memslot when
there are active shadow MMU pages.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Pull x86 kvm updates from Paolo Bonzini:
"x86:
- KVM currently invalidates the entirety of the page tables, not just
those for the memslot being touched, when a memslot is moved or
deleted.
This does not traditionally have particularly noticeable overhead,
but Intel's TDX will require the guest to re-accept private pages
if they are dropped from the secure EPT, which is a non starter.
Actually, the only reason why this is not already being done is a
bug which was never fully investigated and caused VM instability
with assigned GeForce GPUs, so allow userspace to opt into the new
behavior.
- Advertise AVX10.1 to userspace (effectively prep work for the
"real" AVX10 functionality that is on the horizon)
- Rework common MSR handling code to suppress errors on userspace
accesses to unsupported-but-advertised MSRs
This will allow removing (almost?) all of KVM's exemptions for
userspace access to MSRs that shouldn't exist based on the vCPU
model (the actual cleanup is non-trivial future work)
- Rework KVM's handling of x2APIC ICR, again, because AMD (x2AVIC)
splits the 64-bit value into the legacy ICR and ICR2 storage,
whereas Intel (APICv) stores the entire 64-bit value at the ICR
offset
- Fix a bug where KVM would fail to exit to userspace if one was
triggered by a fastpath exit handler
- Add fastpath handling of HLT VM-Exit to expedite re-entering the
guest when there's already a pending wake event at the time of the
exit
- Fix a WARN caused by RSM entering a nested guest from SMM with
invalid guest state, by forcing the vCPU out of guest mode prior to
signalling SHUTDOWN (the SHUTDOWN hits the VM altogether, not the
nested guest)
- Overhaul the "unprotect and retry" logic to more precisely identify
cases where retrying is actually helpful, and to harden all retry
paths against putting the guest into an infinite retry loop
- Add support for yielding, e.g. to honor NEED_RESCHED, when zapping
rmaps in the shadow MMU
- Refactor pieces of the shadow MMU related to aging SPTEs in
prepartion for adding multi generation LRU support in KVM
- Don't stuff the RSB after VM-Exit when RETPOLINE=y and AutoIBRS is
enabled, i.e. when the CPU has already flushed the RSB
- Trace the per-CPU host save area as a VMCB pointer to improve
readability and cleanup the retrieval of the SEV-ES host save area
- Remove unnecessary accounting of temporary nested VMCB related
allocations
- Set FINAL/PAGE in the page fault error code for EPT violations if
and only if the GVA is valid. If the GVA is NOT valid, there is no
guest-side page table walk and so stuffing paging related metadata
is nonsensical
- Fix a bug where KVM would incorrectly synthesize a nested VM-Exit
instead of emulating posted interrupt delivery to L2
- Add a lockdep assertion to detect unsafe accesses of vmcs12
structures
- Harden eVMCS loading against an impossible NULL pointer deref
(really truly should be impossible)
- Minor SGX fix and a cleanup
- Misc cleanups
Generic:
- Register KVM's cpuhp and syscore callbacks when enabling
virtualization in hardware, as the sole purpose of said callbacks
is to disable and re-enable virtualization as needed
- Enable virtualization when KVM is loaded, not right before the
first VM is created
Together with the previous change, this simplifies a lot the logic
of the callbacks, because their very existence implies
virtualization is enabled
- Fix a bug that results in KVM prematurely exiting to userspace for
coalesced MMIO/PIO in many cases, clean up the related code, and
add a testcase
- Fix a bug in kvm_clear_guest() where it would trigger a buffer
overflow _if_ the gpa+len crosses a page boundary, which thankfully
is guaranteed to not happen in the current code base. Add WARNs in
more helpers that read/write guest memory to detect similar bugs
Selftests:
- Fix a goof that caused some Hyper-V tests to be skipped when run on
bare metal, i.e. NOT in a VM
- Add a regression test for KVM's handling of SHUTDOWN for an SEV-ES
guest
- Explicitly include one-off assets in .gitignore. Past Sean was
completely wrong about not being able to detect missing .gitignore
entries
- Verify userspace single-stepping works when KVM happens to handle a
VM-Exit in its fastpath
- Misc cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (127 commits)
Documentation: KVM: fix warning in "make htmldocs"
s390: Enable KVM_S390_UCONTROL config in debug_defconfig
selftests: kvm: s390: Add VM run test case
KVM: SVM: let alternatives handle the cases when RSB filling is required
KVM: VMX: Set PFERR_GUEST_{FINAL,PAGE}_MASK if and only if the GVA is valid
KVM: x86/mmu: Use KVM_PAGES_PER_HPAGE() instead of an open coded equivalent
KVM: x86/mmu: Add KVM_RMAP_MANY to replace open coded '1' and '1ul' literals
KVM: x86/mmu: Fold mmu_spte_age() into kvm_rmap_age_gfn_range()
KVM: x86/mmu: Morph kvm_handle_gfn_range() into an aging specific helper
KVM: x86/mmu: Honor NEED_RESCHED when zapping rmaps and blocking is allowed
KVM: x86/mmu: Add a helper to walk and zap rmaps for a memslot
KVM: x86/mmu: Plumb a @can_yield parameter into __walk_slot_rmaps()
KVM: x86/mmu: Move walk_slot_rmaps() up near for_each_slot_rmap_range()
KVM: x86/mmu: WARN on MMIO cache hit when emulating write-protected gfn
KVM: x86/mmu: Detect if unprotect will do anything based on invalid_list
KVM: x86/mmu: Subsume kvm_mmu_unprotect_page() into the and_retry() version
KVM: x86: Rename reexecute_instruction()=>kvm_unprotect_and_retry_on_failure()
KVM: x86: Update retry protection fields when forcing retry on emulation failure
KVM: x86: Apply retry protection to "unprotect on failure" path
KVM: x86: Check EMULTYPE_WRITE_PF_TO_SP before unprotecting gfn
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull 'struct fd' updates from Al Viro:
"Just the 'struct fd' layout change, with conversion to accessor
helpers"
* tag 'pull-stable-struct_fd' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
add struct fd constructors, get rid of __to_fd()
struct fd: representation change
introduce fd_file(), convert all accessors to it.
|
|
KVM VMX changes for 6.12:
- Set FINAL/PAGE in the page fault error code for EPT Violations if and only
if the GVA is valid. If the GVA is NOT valid, there is no guest-side page
table walk and so stuffing paging related metadata is nonsensical.
- Fix a bug where KVM would incorrectly synthesize a nested VM-Exit instead of
emulating posted interrupt delivery to L2.
- Add a lockdep assertion to detect unsafe accesses of vmcs12 structures.
- Harden eVMCS loading against an impossible NULL pointer deref (really truly
should be impossible).
- Minor SGX fix and a cleanup.
|
|
KVM SVM changes for 6.12:
- Don't stuff the RSB after VM-Exit when RETPOLINE=y and AutoIBRS is enabled,
i.e. when the CPU has already flushed the RSB.
- Trace the per-CPU host save area as a VMCB pointer to improve readability
and cleanup the retrieval of the SEV-ES host save area.
- Remove unnecessary accounting of temporary nested VMCB related allocations.
|
|
into HEAD
KVM VMX and x86 PAT MSR macro cleanup for 6.12:
- Add common defines for the x86 architectural memory types, i.e. the types
that are shared across PAT, MTRRs, VMCSes, and EPTPs.
- Clean up the various VMX MSR macros to make the code self-documenting
(inasmuch as possible), and to make it less painful to add new macros.
|
|
KVM x86 MMU changes for 6.12:
- Overhaul the "unprotect and retry" logic to more precisely identify cases
where retrying is actually helpful, and to harden all retry paths against
putting the guest into an infinite retry loop.
- Add support for yielding, e.g. to honor NEED_RESCHED, when zapping rmaps in
the shadow MMU.
- Refactor pieces of the shadow MMU related to aging SPTEs in prepartion for
adding MGLRU support in KVM.
- Misc cleanups
|
|
KVM x86 misc changes for 6.12
- Advertise AVX10.1 to userspace (effectively prep work for the "real" AVX10
functionality that is on the horizon).
- Rework common MSR handling code to suppress errors on userspace accesses to
unsupported-but-advertised MSRs. This will allow removing (almost?) all of
KVM's exemptions for userspace access to MSRs that shouldn't exist based on
the vCPU model (the actual cleanup is non-trivial future work).
- Rework KVM's handling of x2APIC ICR, again, because AMD (x2AVIC) splits the
64-bit value into the legacy ICR and ICR2 storage, whereas Intel (APICv)
stores the entire 64-bit value a the ICR offset.
- Fix a bug where KVM would fail to exit to userspace if one was triggered by
a fastpath exit handler.
- Add fastpath handling of HLT VM-Exit to expedite re-entering the guest when
there's already a pending wake event at the time of the exit.
- Finally fix the RSM vs. nested VM-Enter WARN by forcing the vCPU out of
guest mode prior to signalling SHUTDOWN (architecturally, the SHUTDOWN is
supposed to hit L1, not L2).
|
|
Register KVM's cpuhp and syscore callbacks when enabling virtualization in
hardware, as the sole purpose of said callbacks is to disable and re-enable
virtualization as needed.
The primary motivation for this series is to simplify dealing with enabling
virtualization for Intel's TDX, which needs to enable virtualization
when kvm-intel.ko is loaded, i.e. long before the first VM is created.
That said, this is a nice cleanup on its own. By registering the callbacks
on-demand, the callbacks themselves don't need to check kvm_usage_count,
because their very existence implies a non-zero count.
Patch 1 (re)adds a dedicated lock for kvm_usage_count. This avoids a
lock ordering issue between cpus_read_lock() and kvm_lock. The lock
ordering issue still exist in very rare cases, and will be fixed for
good by switching vm_list to an (S)RCU-protected list.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Today whenever a memslot is moved or deleted, KVM invalidates the entire
page tables and generates fresh ones based on the new memslot layout.
This behavior traditionally was kept because of a bug which was never
fully investigated and caused VM instability with assigned GeForce
GPUs. It generally does not have a huge overhead, because the old
MMU is able to reuse cached page tables and the new one is more
scalabale and can resolve EPT violations/nested page faults in parallel,
but it has worse performance if the guest frequently deletes and
adds small memslots, and it's entirely not viable for TDX. This is
because TDX requires re-accepting of private pages after page dropping.
For non-TDX VMs, this series therefore introduces the
KVM_X86_QUIRK_SLOT_ZAP_ALL quirk, enabling users to control the behavior
of memslot zapping when a memslot is moved/deleted. The quirk is turned
on by default, leading to the zapping of all SPTEs when a memslot is
moved/deleted; users however have the option to turn off the quirk,
which limits the zapping only to those SPTEs hat lie within the range
of memslot being moved/deleted.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Pull kvm fix from Paolo Bonzini:
"Do not always honor guest PAT on CPUs that support self-snoop.
This triggers an issue in the bochsdrm driver, which used ioremap()
instead of ioremap_wc() to map the video RAM.
The revert lets video RAM use the WB memory type instead of the slower
UC memory type"
* tag 'for-linus-6.11' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
Revert "KVM: VMX: Always honor guest PAT on CPUs that support self-snoop"
|
|
This reverts commit 377b2f359d1f71c75f8cc352b5c81f2210312d83.
This caused a regression with the bochsdrm driver, which used ioremap()
instead of ioremap_wc() to map the video RAM. After the commit, the
WB memory type is used without the IGNORE_PAT, resulting in the slower
UC memory type. In fact, UC is slow enough to basically cause guests
to not boot... but only on new processors such as Sapphire Rapids and
Cascade Lake. Coffee Lake for example works properly, though that might
also be an effect of being on a larger, more NUMA system.
The driver has been fixed but that does not help older guests. Until we
figure out whether Cascade Lake and newer processors are working as
intended, revert the commit. Long term we might add a quirk, but the
details depend on whether the processors are working as intended: for
example if they are, the quirk might reference bochs-compatible devices,
e.g. in the name and documentation, so that userspace can disable the
quirk by default and only leave it enabled if such a device is being
exposed to the guest.
If instead this is actually a bug in CLX+, then the actions we need to
take are different and depend on the actual cause of the bug.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Remove superfluous RSB filling after a VMEXIT when the CPU already has
flushed the RSB after a VMEXIT when AutoIBRS is enabled.
The initial implementation for adding RETPOLINES added an ALTERNATIVES
implementation for filling the RSB after a VMEXIT in commit 117cc7a908c8
("x86/retpoline: Fill return stack buffer on vmexit").
Later, X86_FEATURE_RSB_VMEXIT was added in commit 9756bba28470
("x86/speculation: Fill RSB on vmexit for IBRS") to handle stuffing the
RSB if RETPOLINE=y *or* KERNEL_IBRS=y, i.e. to also stuff the RSB if the
kernel is configured to do IBRS mitigations on entry/exit.
The AutoIBRS (on AMD) feature implementation added in commit e7862eda309e
("x86/cpu: Support AMD Automatic IBRS") used the already-implemented logic
for EIBRS in spectre_v2_determine_rsb_fill_type_on_vmexit() -- but did not
update the code at VMEXIT to act on the mode selected in that function --
resulting in VMEXITs continuing to clear the RSB when RETPOLINES are
enabled, despite the presence of AutoIBRS.
Signed-off-by: Amit Shah <amit.shah@amd.com>
Link: https://lore.kernel.org/r/20240807123531.69677-1-amit@kernel.org
[sean: massage changeloge, drop comment about AMD not needing RSB_VMEXIT_LITE]
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Set PFERR_GUEST_{FINAL,PAGE}_MASK based on EPT_VIOLATION_GVA_TRANSLATED if
and only if EPT_VIOLATION_GVA_IS_VALID is also set in exit qualification.
Per the SDM, bit 8 (EPT_VIOLATION_GVA_TRANSLATED) is valid if and only if
bit 7 (EPT_VIOLATION_GVA_IS_VALID) is set, and is '0' if bit 7 is '0'.
Bit 7 (a.k.a. EPT_VIOLATION_GVA_IS_VALID)
Set if the guest linear-address field is valid. The guest linear-address
field is valid for all EPT violations except those resulting from an
attempt to load the guest PDPTEs as part of the execution of the MOV CR
instruction and those due to trace-address pre-translation
Bit 8 (a.k.a. EPT_VIOLATION_GVA_TRANSLATED)
If bit 7 is 1:
• Set if the access causing the EPT violation is to a guest-physical
address that is the translation of a linear address.
• Clear if the access causing the EPT violation is to a paging-structure
entry as part of a page walk or the update of an accessed or dirty bit.
Reserved if bit 7 is 0 (cleared to 0).
Failure to guard the logic on GVA_IS_VALID results in KVM marking the page
fault as PFERR_GUEST_PAGE_MASK when there is no known GVA, which can put
the vCPU into an infinite loop due to kvm_mmu_page_fault() getting false
positive on its PFERR_NESTED_GUEST_PAGE logic (though only because that
logic is also buggy/flawed).
In practice, this is largely a non-issue because so GVA_IS_VALID is almost
always set. However, when TDX comes along, GVA_IS_VALID will *never* be
set, as the TDX Module deliberately clears bits 12:7 in exit qualification,
e.g. so that the faulting virtual address and other metadata that aren't
practically useful for the hypervisor aren't leaked to the untrusted host.
When exit is due to EPT violation, bits 12-7 of the exit qualification
are cleared to 0.
Fixes: eebed2438923 ("kvm: nVMX: Add support for fast unprotection of nested guest page tables")
Reviewed-by: Yuan Yao <yuan.yao@intel.com>
Link: https://lore.kernel.org/r/20240831001538.336683-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Use KVM_PAGES_PER_HPAGE() instead of open coding equivalent logic that is
anything but obvious.
No functional change intended, and verified by compiling with the below
assertions:
BUILD_BUG_ON((1UL << KVM_HPAGE_GFN_SHIFT(PG_LEVEL_4K)) !=
KVM_PAGES_PER_HPAGE(PG_LEVEL_4K));
BUILD_BUG_ON((1UL << KVM_HPAGE_GFN_SHIFT(PG_LEVEL_2M)) !=
KVM_PAGES_PER_HPAGE(PG_LEVEL_2M));
BUILD_BUG_ON((1UL << KVM_HPAGE_GFN_SHIFT(PG_LEVEL_1G)) !=
KVM_PAGES_PER_HPAGE(PG_LEVEL_1G));
Link: https://lore.kernel.org/r/20240809194335.1726916-19-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Replace all of the open coded '1' literals used to mark a PTE list as
having many/multiple entries with a proper define. It's hard enough to
read the code with one magic bit, and a future patch to support "locking"
a single rmap will add another.
No functional change intended.
Link: https://lore.kernel.org/r/20240809194335.1726916-17-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Fold mmu_spte_age() into its sole caller now that aging and testing for
young SPTEs is handled in a common location, i.e. doesn't require more
helpers.
Opportunistically remove the use of mmu_spte_get_lockless(), as mmu_lock
is held (for write!), and marking SPTEs for access tracking outside of
mmu_lock is unsafe (at least, as written). I.e. using the lockless
accessor is quite misleading.
No functional change intended.
Link: https://lore.kernel.org/r/20240809194335.1726916-16-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Rework kvm_handle_gfn_range() into an aging-specic helper,
kvm_rmap_age_gfn_range(). In addition to purging a bunch of unnecessary
boilerplate code, this sets the stage for aging rmap SPTEs outside of
mmu_lock.
Note, there's a small functional change, as kvm_test_age_gfn() will now
return immediately if a young SPTE is found, whereas previously KVM would
continue iterating over other levels.
Link: https://lore.kernel.org/r/20240809194335.1726916-15-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Convert kvm_unmap_gfn_range(), which is the helper that zaps rmap SPTEs in
response to an mmu_notifier invalidation, to use __kvm_rmap_zap_gfn_range()
and feed in range->may_block. In other words, honor NEED_RESCHED by way of
cond_resched() when zapping rmaps. This fixes a long-standing issue where
KVM could process an absurd number of rmap entries without ever yielding,
e.g. if an mmu_notifier fired on a PUD (or larger) range.
Opportunistically rename __kvm_zap_rmap() to kvm_zap_rmap(), and drop the
old kvm_zap_rmap(). Ideally, the shuffling would be done in a different
patch, but that just makes the compiler unhappy, e.g.
arch/x86/kvm/mmu/mmu.c:1462:13: error: ‘kvm_zap_rmap’ defined but not used
Reported-by: Peter Xu <peterx@redhat.com>
Link: https://lore.kernel.org/r/20240809194335.1726916-14-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Add a dedicated helper to walk and zap rmaps for a given memslot so that
the code can be shared between KVM-initiated zaps and mmu_notifier
invalidations.
No functional change intended.
Link: https://lore.kernel.org/r/20240809194335.1726916-13-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Add a @can_yield param to __walk_slot_rmaps() to control whether or not
dropping mmu_lock and conditionally rescheduling is allowed. This will
allow using __walk_slot_rmaps() and thus cond_resched() to handle
mmu_notifier invalidations, which usually allow blocking/yielding, but not
when invoked by the OOM killer.
Link: https://lore.kernel.org/r/20240809194335.1726916-12-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
