| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
test_barrier fails on s390 because of the missing KCSAN instrumentation
for several synchronization primitives.
Add it to barriers by defining __mb(), __rmb(), __wmb(), __dma_rmb()
and __dma_wmb(), and letting the common code in asm-generic/barrier.h
do the rest.
Spinlocks require instrumentation only on the unlock path; notify KCSAN
that the CPU cannot move memory accesses outside of the spin lock. In
reality it also cannot move stores inside of it, but this is not
important and can be omitted.
Reported-by: Tobias Huschle <huschle@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Currently it is not detectable from within Linux when PCI instructions
are retried because of a busy condition. Detecting such conditions and
especially how long they lasted can however be quite useful in problem
determination. This patch enables this by adding an s390dbf error log
when a CC 2 is first encountered as well as after the retried
instruction.
Despite being unlikely it may be possible that these added debug
messages drown out important other messages so allow setting the debug
level in zpci_err_insn*() and set their level to 1 so they can be
filtered out if need be.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Currently when a PCI instruction returns a non-zero condition code it
can be very hard to tell from the s390dbf logs what kind of instruction
was executed. In case of PCI memory I/O (MIO) instructions it is even
impossible to tell if we attempted a load, store or block store or how
large the access was because only the address is logged.
Improve this by adding an indicator byte for the instruction type to the
error record and also store the length of the access for MIO
instructions where this can not be deduced from the request.
We use the following indicator values:
- 'l': PCI load
- 's': PCI store
- 'b': PCI store block
- 'L': PCI load (MIO)
- 'S': PCI store (MIO)
- 'B': PCI store block (MIO)
- 'M': MPCIFC
- 'R': RPCIT
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Availability events are logged in s390dbf in s390dbf/pci_error/hex_ascii
even though they don't indicate an error condition.
They have also become redundant as commit 6526a597a2e85 ("s390/pci: add
simpler s390dbf traces for events") added an s390dbf/pci_msg/sprintf log
entry for availability events which contains all non reserved fields of
struct zpci_ccdf_avail. On the other hand the availability entries in
the error log make it easy to miss actual errors and may even overwrite
error entries if the message buffer wraps.
Thus simply remove the availability events from the error log thereby
establishing the rule that any content in s390dbf/pci_error indicates
some kind of error.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
While the zpci_dbg() macro offers a level parameter this is currently
largely unused. The only instance with higher importance than 3 is the
UID checking change debug message which is not actually more important
as the UID uniqueness guarantee is already exposed in sysfs so this
should rather be 3 as well.
On the other hand the "add ..." message which shows what devices are
visible at the lowest level is essential during problem determination.
By setting its level to 1, lowering the debug level can act as a filter
to only show the available functions.
On the error side the default level is set to 6 while all existing
messages are printed at level 0. This is inconsistent and means there is
no room for having messages be invisible on the default level so instead
set the default level to 3 like for errors matching the default for
debug messages.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Randomize the address of vdso if randomize_va_space is enabled.
Note that this keeps the vdso address on the same PMD as the stack
to avoid allocating an extra page table just for vdso.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
In the current code vdso is mapped below the stack. This is
problematic when programs mapped to the top of the address space
are allocating a lot of memory, because the heap will clash with
the vdso. To avoid this map the vdso above the stack and move
STACK_TOP so that it all fits into three level paging.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
This is a preparation patch for adding vdso randomization to s390.
It adds a function vdso_size(), which will be used later in calculating
the STACK_TOP value. It also moves the vdso mapping into a new function
vdso_map(), to keep the code similar to other architectures.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
This basically reverts commit 9e78a13bfb16 ("[S390] reduce miminum
gap between stack and mmap_base"). 32MB is not enough space
between stack and mmap for some programs. Given that compat
task aren't common these days, lets revert back to 128MB.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
This patch tries to fix as much as possible of the
checkpatch.pl --strict findings:
CHECK: Logical continuations should be on the previous line
CHECK: No space is necessary after a cast
CHECK: Alignment should match open parenthesis
CHECK: 'useable' may be misspelled - perhaps 'usable'?
WARNING: Possible repeated word: 'is'
CHECK: spaces preferred around that '*' (ctx:VxV)
CHECK: Comparison to NULL could be written "!msg"
CHECK: Prefer kzalloc(sizeof(*zc)...) over kzalloc(sizeof(struct...)...)
CHECK: Unnecessary parentheses around resp_type->work
CHECK: Avoid CamelCase: <xcRB>
There is no functional change comming with this patch, only
code cleanup, renaming, whitespaces, indenting, ... but no
semantic change in any way. Also the API (zcrypt and pkey
header file) is semantically unchanged.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Jürgen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
This patch does a little cleanup on the CPRBX struct
in zcrypt.h and the redundant CPRB struct definition in
zcrypt_msgtype6.c. Especially some of the misleading
fields from the CPRBX struct have been removed.
There is no semantic change coming with this patch.
The field names changed in the XCRB struct are only related
to reserved fields which should never been used.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Jürgen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Fix the following coccicheck warnings:
./arch/s390/include/asm/scsw.h:695:47-49: WARNING
!A || A && B is equivalent to !A || B
I apply a readable version just to get rid of a warning.
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Link: https://lore.kernel.org/r/1649297808-5048-1-git-send-email-baihaowen@meizu.com
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
SPX instruction called from set_prefix() expects physical
address of the lowcore to be installed, but instead the
virtual address is passed.
Note: this does not fix a bug currently, since virtual and
physical addresses are identical.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
If the facility IPL-complete-control is present then the last diag308
call made by kexec shall set the end-of-ipl flag in the subcode register
to signal the hypervisor that this is the last diag308 call made by Linux.
Only the diag308 calls made during a regular kexec need to set
the end-of-ipl flag, in all other cases the hypervisor will ignore it.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The presence of the IPL-complete-control facility can be derived
from the hypervisor's SCLP info response.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Pull kvm fixes from Paolo Bonzini:
"The main and larger change here is a workaround for AMD's lack of
cache coherency for encrypted-memory guests.
I have another patch pending, but it's waiting for review from the
architecture maintainers.
RISC-V:
- Remove 's' & 'u' as valid ISA extension
- Do not allow disabling the base extensions 'i'/'m'/'a'/'c'
x86:
- Fix NMI watchdog in guests on AMD
- Fix for SEV cache incoherency issues
- Don't re-acquire SRCU lock in complete_emulated_io()
- Avoid NULL pointer deref if VM creation fails
- Fix race conditions between APICv disabling and vCPU creation
- Bugfixes for disabling of APICv
- Preserve BSP MSR_KVM_POLL_CONTROL across suspend/resume
selftests:
- Do not use bitfields larger than 32-bits, they differ between GCC
and clang"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: selftests: introduce and use more page size-related constants
kvm: selftests: do not use bitfields larger than 32-bits for PTEs
KVM: SEV: add cache flush to solve SEV cache incoherency issues
KVM: SVM: Flush when freeing encrypted pages even on SME_COHERENT CPUs
KVM: SVM: Simplify and harden helper to flush SEV guest page(s)
KVM: selftests: Silence compiler warning in the kvm_page_table_test
KVM: x86/pmu: Update AMD PMC sample period to fix guest NMI-watchdog
x86/kvm: Preserve BSP MSR_KVM_POLL_CONTROL across suspend/resume
KVM: SPDX style and spelling fixes
KVM: x86: Skip KVM_GUESTDBG_BLOCKIRQ APICv update if APICv is disabled
KVM: x86: Pend KVM_REQ_APICV_UPDATE during vCPU creation to fix a race
KVM: nVMX: Defer APICv updates while L2 is active until L1 is active
KVM: x86: Tag APICv DISABLE inhibit, not ABSENT, if APICv is disabled
KVM: Initialize debugfs_dentry when a VM is created to avoid NULL deref
KVM: Add helpers to wrap vcpu->srcu_idx and yell if it's abused
KVM: RISC-V: Use kvm_vcpu.srcu_idx, drop RISC-V's unnecessary copy
KVM: x86: Don't re-acquire SRCU lock in complete_emulated_io()
RISC-V: KVM: Restrict the extensions that can be disabled
RISC-V: KVM: Remove 's' & 'u' as valid ISA extension
|
|
Add wrappers to acquire/release KVM's SRCU lock when stashing the index
in vcpu->src_idx, along with rudimentary detection of illegal usage,
e.g. re-acquiring SRCU and thus overwriting vcpu->src_idx. Because the
SRCU index is (currently) either 0 or 1, illegal nesting bugs can go
unnoticed for quite some time and only cause problems when the nested
lock happens to get a different index.
Wrap the WARNs in PROVE_RCU=y, and make them ONCE, otherwise KVM will
likely yell so loudly that it will bring the kernel to its knees.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20220415004343.2203171-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Huge page backed vmalloc memory could benefit performance in many cases.
However, some users of vmalloc may not be ready to handle huge pages for
various reasons: hardware constraints, potential pages split, etc.
VM_NO_HUGE_VMAP was introduced to allow vmalloc users to opt-out huge
pages. However, it is not easy to track down all the users that require
the opt-out, as the allocation are passed different stacks and may cause
issues in different layers.
To address this issue, replace VM_NO_HUGE_VMAP with an opt-in flag,
VM_ALLOW_HUGE_VMAP, so that users that benefit from huge pages could ask
specificially.
Also, remove vmalloc_no_huge() and add opt-in helper vmalloc_huge().
Fixes: fac54e2bfb5b ("x86/Kconfig: Select HAVE_ARCH_HUGE_VMALLOC with HAVE_ARCH_HUGE_VMAP")
Link: https://lore.kernel.org/netdev/14444103-d51b-0fb3-ee63-c3f182f0b546@molgen.mpg.de/"
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Song Liu <song@kernel.org>
Reviewed-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pass a boolean flag to indicate if swiotlb needs to be enabled based on
the addressing needs, and replace the verbose argument with a set of
flags, including one to force enable bounce buffering.
Note that this patch removes the possibility to force xen-swiotlb use
with the swiotlb=force parameter on the command line on x86 (arm and
arm64 never supported that), but this interface will be restored shortly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
s390 defines current_stack_pointer as function while all other
architectures use 'register unsigned long asm("<stackptr reg>").
This make codes like the following from check_stack_object() fail:
if (IS_ENABLED(CONFIG_STACK_GROWSUP)) {
if ((void *)current_stack_pointer < obj + len)
return BAD_STACK;
} else {
if (obj < (void *)current_stack_pointer)
return BAD_STACK;
}
because this would compare the address of current_stack_pointer() and
not the stackpointer value.
Reported-by: Karsten Graul <kgraul@linux.ibm.com>
Fixes: 2792d84e6da5 ("usercopy: Check valid lifetime via stack depth")
Cc: Kees Cook <keescook@chromium.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Just use absolute_pointer() like e.g. in commit 545c272232ca ("alpha:
Silence -Warray-bounds warnings") to get rid of this warning:
arch/s390/kernel/machine_kexec.c:59:9: warning: ‘memcpy’ offset [0, 511] is out of the bounds [0, 0] [-Warray-bounds]
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Add config and compile options which allow to compile with z16
optimizations if the compiler supports it.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Add detection for machine types 0x3931 and 0x3932 and set ELF platform
name to z16.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Pull kvm fixes from Paolo Bonzini:
- Only do MSR filtering for MSRs accessed by rdmsr/wrmsr
- Documentation improvements
- Prevent module exit until all VMs are freed
- PMU Virtualization fixes
- Fix for kvm_irq_delivery_to_apic_fast() NULL-pointer dereferences
- Other miscellaneous bugfixes
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (42 commits)
KVM: x86: fix sending PV IPI
KVM: x86/mmu: do compare-and-exchange of gPTE via the user address
KVM: x86: Remove redundant vm_entry_controls_clearbit() call
KVM: x86: cleanup enter_rmode()
KVM: x86: SVM: fix tsc scaling when the host doesn't support it
kvm: x86: SVM: remove unused defines
KVM: x86: SVM: move tsc ratio definitions to svm.h
KVM: x86: SVM: fix avic spec based definitions again
KVM: MIPS: remove reference to trap&emulate virtualization
KVM: x86: document limitations of MSR filtering
KVM: x86: Only do MSR filtering when access MSR by rdmsr/wrmsr
KVM: x86/emulator: Emulate RDPID only if it is enabled in guest
KVM: x86/pmu: Fix and isolate TSX-specific performance event logic
KVM: x86: mmu: trace kvm_mmu_set_spte after the new SPTE was set
KVM: x86/svm: Clear reserved bits written to PerfEvtSeln MSRs
KVM: x86: Trace all APICv inhibit changes and capture overall status
KVM: x86: Add wrappers for setting/clearing APICv inhibits
KVM: x86: Make APICv inhibit reasons an enum and cleanup naming
KVM: X86: Handle implicit supervisor access with SMAP
KVM: X86: Rename variable smap to not_smap in permission_fault()
...
|
|
Don't actually set a request bit in vcpu->requests when making a request
purely to force a vCPU to exit the guest. Logging a request but not
actually consuming it would cause the vCPU to get stuck in an infinite
loop during KVM_RUN because KVM would see the pending request and bail
from VM-Enter to service the request.
Note, it's currently impossible for KVM to set KVM_REQ_GPC_INVALIDATE as
nothing in KVM is wired up to set guest_uses_pa=true. But, it'd be all
too easy for arch code to introduce use of kvm_gfn_to_pfn_cache_init()
without implementing handling of the request, especially since getting
test coverage of MMU notifier interaction with specific KVM features
usually requires a directed test.
Opportunistically rename gfn_to_pfn_cache_invalidate_start()'s wake_vcpus
to evict_vcpus. The purpose of the request is to get vCPUs out of guest
mode, it's supposed to _avoid_ waking vCPUs that are blocking.
Opportunistically rename KVM_REQ_GPC_INVALIDATE to be more specific as to
what it wants to accomplish, and to genericize the name so that it can
used for similar but unrelated scenarios, should they arise in the future.
Add a comment and documentation to explain why the "no action" request
exists.
Add compile-time assertions to help detect improper usage. Use the inner
assertless helper in the one s390 path that makes requests without a
hardcoded request.
Cc: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220223165302.3205276-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
"Assorted bits and pieces"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
aio: drop needless assignment in aio_read()
clean overflow checks in count_mounts() a bit
seq_file: fix NULL pointer arithmetic warning
uml/x86: use x86 load_unaligned_zeropad()
asm/user.h: killed unused macros
constify struct path argument of finish_automount()/do_add_mount()
fs: Remove FIXME comment in generic_write_checks()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Vasily Gorbik:
- Add kretprobes framepointer verification and return address recovery
in stacktrace.
- Support control domain masks on custom zcrypt devices and filter
admin requests.
- Cleanup timer API usage.
- Rework absolute lowcore access helpers.
- Other various small improvements and fixes.
* tag 's390-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (26 commits)
s390/alternatives: avoid using jgnop mnemonic
s390/pci: rename get_zdev_by_bus() to zdev_from_bus()
s390/pci: improve zpci_dev reference counting
s390/smp: use physical address for SIGP_SET_PREFIX command
s390: cleanup timer API use
s390/zcrypt: fix using the correct variable for sizeof()
s390/vfio-ap: fix kernel doc and signature of group notifier functions
s390/maccess: rework absolute lowcore accessors
s390/smp: cleanup control register update routines
s390/smp: cleanup target CPU callback starting
s390/test_unwind: verify __kretprobe_trampoline is replaced
s390/unwind: avoid duplicated unwinding entries for kretprobes
s390/unwind: recover kretprobe modified return address in stacktrace
s390/kprobes: enable kretprobes framepointer verification
s390/test_unwind: extend kretprobe test
s390/ap: adjust whitespace
s390/ap: use insn format for new instructions
s390/alternatives: use insn format for new instructions
s390/alternatives: use instructions instead of byte patterns
s390/traps: improve panic message for translation-specification exception
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add new environment variables, USERCFLAGS and USERLDFLAGS to allow
additional flags to be passed to user-space programs.
- Fix missing fflush() bugs in Kconfig and fixdep
- Fix a minor bug in the comment format of the .config file
- Make kallsyms ignore llvm's local labels, .L*
- Fix UAPI compile-test for cross-compiling with Clang
- Extend the LLVM= syntax to support LLVM=<suffix> form for using a
particular version of LLVm, and LLVM=<prefix> form for using custom
LLVM in a particular directory path.
- Clean up Makefiles
* tag 'kbuild-v5.18-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: Make $(LLVM) more flexible
kbuild: add --target to correctly cross-compile UAPI headers with Clang
fixdep: use fflush() and ferror() to ensure successful write to files
arch: syscalls: simplify uapi/kapi directory creation
usr/include: replace extra-y with always-y
certs: simplify empty certs creation in certs/Makefile
certs: include certs/signing_key.x509 unconditionally
kallsyms: ignore all local labels prefixed by '.L'
kconfig: fix missing '# end of' for empty menu
kconfig: add fflush() before ferror() check
kbuild: replace $(if A,A,B) with $(or A,B)
kbuild: Add environment variables for userprogs flags
kbuild: unify cmd_copy and cmd_shipped
|
|
$(shell ...) expands to empty. There is no need to assign it to _dummy.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull ptrace cleanups from Eric Biederman:
"This set of changes removes tracehook.h, moves modification of all of
the ptrace fields inside of siglock to remove races, adds a missing
permission check to ptrace.c
The removal of tracehook.h is quite significant as it has been a major
source of confusion in recent years. Much of that confusion was around
task_work and TIF_NOTIFY_SIGNAL (which I have now decoupled making the
semantics clearer).
For people who don't know tracehook.h is a vestiage of an attempt to
implement uprobes like functionality that was never fully merged, and
was later superseeded by uprobes when uprobes was merged. For many
years now we have been removing what tracehook functionaly a little
bit at a time. To the point where anything left in tracehook.h was
some weird strange thing that was difficult to understand"
* tag 'ptrace-cleanups-for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ptrace: Remove duplicated include in ptrace.c
ptrace: Check PTRACE_O_SUSPEND_SECCOMP permission on PTRACE_SEIZE
ptrace: Return the signal to continue with from ptrace_stop
ptrace: Move setting/clearing ptrace_message into ptrace_stop
tracehook: Remove tracehook.h
resume_user_mode: Move to resume_user_mode.h
resume_user_mode: Remove #ifdef TIF_NOTIFY_RESUME in set_notify_resume
signal: Move set_notify_signal and clear_notify_signal into sched/signal.h
task_work: Decouple TIF_NOTIFY_SIGNAL and task_work
task_work: Call tracehook_notify_signal from get_signal on all architectures
task_work: Introduce task_work_pending
task_work: Remove unnecessary include from posix_timers.h
ptrace: Remove tracehook_signal_handler
ptrace: Remove arch_syscall_{enter,exit}_tracehook
ptrace: Create ptrace_report_syscall_{entry,exit} in ptrace.h
ptrace/arm: Rename tracehook_report_syscall report_syscall
ptrace: Move ptrace_report_syscall into ptrace.h
|
|
jgnop mnemonic is only available since binutils 2.36,
kernel minimal required version is 2.23. Stick to brcl
to avoid build errors.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Fixes: 4afeb670710e ("s390/alternatives: use instructions instead of byte patterns")
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Getting a zpci_dev via get_zdev_by_bus() uses the long lived reference
held in zbus->function[devfn]. This is accounted for in
pcibios_add_device() and pcibios_release_device().
Therefore there is no need to increment the reference count in
get_zdev_by_bus() as is done for get_zdev_by_fid(). Instead callers must
not access the device after pcibios_release_device() was called which is
necessary for common PCI code anyway. With this though the very similar
naming may be misleading so rename get_zdev_by_bus() to zdev_from_bus()
emphasizing that we are directly referencing the zdev via the bus.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Currently zpci_dev uses kref based reference counting but only accounts
for one original reference plus one reference from an added pci_dev to
its underlying zpci_dev. Counting just the original reference worked
until the pci_dev reference was added in commit 2a671f77ee49 ("s390/pci:
fix use after free of zpci_dev") because once a zpci_dev goes away, i.e.
enters the reserved state, it would immediately get released. However
with the pci_dev reference this is no longer the case and the zpci_dev
may still appear in multiple availability events indicating that it was
reserved. This was solved by detecting when the zpci_dev is already on
its way out but still hanging around. This has however shown some light
on how unusual our zpci_dev reference counting is.
Improve upon this by modelling zpci_dev reference counting on pci_dev.
Analogous to pci_get_slot() increment the reference count in
get_zdev_by_fid(). Thus all users of get_zdev_by_fid() must drop the
reference once they are done with the zpci_dev.
Similar to pci_scan_single_device(), zpci_create_device() returns the
device with an initial count of 1 and the device added to the zpci_list
(analogous to the PCI bus' device_list). In turn users of
zpci_create_device() must only drop the reference once the device is
gone from the point of view of the zPCI subsystem, it might still be
referenced by the common PCI subsystem though.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Signal processor SIGP_SET_PREFIX command expects physical
address of the lowcore to be installed, but instead the
virtual address is provided.
Note: this does not fix a bug currently, since virtual and
physical addresses are identical.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Macro mem_assign_absolute() is able to access the whole memory, but
is only used and makes sense when updating the absolute lowcore.
Instead, introduce get_abs_lowcore() and put_abs_lowcore() macros
that limit access to absolute lowcore addresses only.
Suggested-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Get rid of duplicate code and redundant data.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Macro mem_assign_absolute() is used to initialize a target
CPU lowcore callback parameters. But despite the macro name
it writes to the absolute lowcore only if the target CPU is
offline. In case the CPU is online the macro does implicitly
write to the normal memory.
That behaviour is correct, but extremely subtle. Sacrifice
few program bits in favour of clarity and distinguish between
online vs offline CPUs and normal vs absolute lowcore pointer.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Reviewed-by: Tobias Huschle <huschle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Currently when unwinding starts from pt_regs or encounters pt_regs along
the way unwinder tries to yield 2 unwinding entries:
1. (reliable) ip1: pt_regs->psw.addr, sp1: regs->gprs[15]
2. (non-reliable) ip2: sp1->gprs[8] (r14), sp2: regs->gprs[15]
In case of kretprobes those are identical and serves no other purpose
than causing confusion over duplicated entries and cause kprobes tests
to fail. So, skip a duplicate non-reliable entry in this case.
With that kretprobes and unwinder implementation now comply with
ARCH_CORRECT_STACKTRACE_ON_KRETPROBE.
Reviewed-by: Tobias Huschle <huschle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Based on commit cd9bc2c92588 ("arm64: Recover kretprobe modified return
address in stacktrace").
"""
Since the kretprobe replaces the function return address with
the __kretprobe_trampoline on the stack, stack unwinder shows it
instead of the correct return address.
This checks whether the next return address is the
__kretprobe_trampoline(), and if so, try to find the correct
return address from the kretprobe instance list.
"""
Original patch series:
https://lore.kernel.org/all/163163030719.489837.2236069935502195491.stgit@devnote2/
Reviewed-by: Tobias Huschle <huschle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Use regs->gprs[15] for framepointer verification. This enables
additional sanity checks for nested kretprobes.
Reviewed-by: Tobias Huschle <huschle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Verify unwinding from kretprobed function.
Reviewed-by: Tobias Huschle <huschle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Adjust indentation of inline assemblies, so all comments
start at the same position.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Use insn format with instruction format specifier instead of plain
longs. This way it is also more obvious that code instead of data is
generated.
The generated code is identical.
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Use insn format with instruction format specifier instead of plain
longs. This way it is also more obvious that code instead of data is
generated.
The generated code is identical.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Use readable nop instructions within the code which generates
the padding areas, instead of unreadable byte patterns.
The generated code is identical.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
There are many different types of translation exceptions but only a
translation-specification exception leads to a kernel panic since it
indicates corrupted page tables, which must never happen.
Improve the panic message so it is a bit more obvious what this is about.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Looks like this endif comment was erroneously unchanged when copied over
from the x86 version.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Link: https://lore.kernel.org/r/20220304090109.29386-1-ruscur@russell.cc
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
