| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Decrease polling rate for erase/trim/discard
- Allow non-sleeping GPIOs for card detect
- Improve mmc block removal path
- Enable support for mmc_sw_reset() for SDIO cards
- Add mmc_sw_reset() to allow users to do a soft reset of the card
- Allow power delay to be tunable via DT
- Allow card detect debounce delay to be tunable via DT
- Enable new quirk to limit clock rate for Marvell 8887 chip
- Don't show eMMC RPMB and BOOT areas in /proc/partitions
- Add capability to avoid 3.3V signaling for fragile HWs
MMC host:
- Improve/fixup support for handle highmem pages
- Remove depends on HAS_DMA in case of platform dependency
- mvsdio: Enable support for erase/trim/discard
- rtsx_usb: Enable support for erase/trim/discard
- renesas_sdhi: Fix WP logic regressions
- renesas_sdhi: Add r8a77965 support
- renesas_sdhi: Add R8A77980 to whitelist
- meson: Add optional support for device reset
- meson: Add support for the Meson-AXG platform
- dw_mmc: Add new driver for BlueField DW variant
- mediatek: Add support for 64G DRAM DMA
- sunxi: Deploy runtime PM support
- jz4740: Add support for JZ4780
- jz4740: Enable support for DT based platforms
- sdhci: Various improvement to timeout handling
- sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
- sdhci-omap: Add support for controller in k2g SoC
- sdhci-omap: Add workarounds for a couple of Erratas
- sdhci-omap: Enable support for generic sdhci DT properties
- sdhci-cadence: Re-send tune request to deal with errata
- sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
- sdhci-pci: Avoid 3.3V signaling on some NI 904x
- sdhci-esdhc-imx: Use watermark levels for PIO access
- sdhci-msm: Improve card detection handling
- sdhci-msm: Add support voltage pad switching"
* tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (104 commits)
mmc: renesas_sdhi: really fix WP logic regressions
mmc: mvsdio: Enable MMC_CAP_ERASE
mmc: mvsdio: Respect card busy time out from mmc core
mmc: sdhci-msm: Remove NO_CARD_NO_RESET quirk
mmc: sunxi: Use ifdef rather than __maybe_unused
mmc: mxmmc: Use ifdef rather than __maybe_unused
mmc: mxmmc: include linux/highmem.h
mmc: sunxi: mark PM functions as __maybe_unused
mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
mmc: au1xmmc: handle highmem pages
mmc: Allow non-sleeping GPIO cd
mmc: sdhci-*: Don't emit error msg if sdhci_add_host() fails
mmc: sd: Define name for default speed dtr
mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
mmc: sdhci-xenon: use match_string() helper
mmc: wbsd: handle highmem pages
mmc: ushc: handle highmem pages
mmc: mxcmmc: handle highmem pages
mmc: atmel-mci: use sg_copy_{from,to}_buffer
mmc: android-goldfish: use sg_copy_{from,to}_buffer
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull time/Y2038 updates from Thomas Gleixner:
- Consolidate SySV IPC UAPI headers
- Convert SySV IPC to the new COMPAT_32BIT_TIME mechanism
- Cleanup the core interfaces and standardize on the ktime_get_* naming
convention.
- Convert the X86 platform ops to timespec64
- Remove the ugly temporary timespec64 hack
* 'timers-2038-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
x86: Convert x86_platform_ops to timespec64
timekeeping: Add more coarse clocktai/boottime interfaces
timekeeping: Add ktime_get_coarse_with_offset
timekeeping: Standardize on ktime_get_*() naming
timekeeping: Clean up ktime_get_real_ts64
timekeeping: Remove timespec64 hack
y2038: ipc: Redirect ipc(SEMTIMEDOP, ...) to compat_ksys_semtimedop
y2038: ipc: Enable COMPAT_32BIT_TIME
y2038: ipc: Use __kernel_timespec
y2038: ipc: Report long times to user space
y2038: ipc: Use ktime_get_real_seconds consistently
y2038: xtensa: Extend sysvipc data structures
y2038: powerpc: Extend sysvipc data structures
y2038: sparc: Extend sysvipc data structures
y2038: parisc: Extend sysvipc data structures
y2038: mips: Extend sysvipc data structures
y2038: arm64: Extend sysvipc compat data structures
y2038: s390: Remove unneeded ipc uapi header files
y2038: ia64: Remove unneeded ipc uapi header files
y2038: alpha: Remove unneeded ipc uapi header files
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timers and timekeeping updates from Thomas Gleixner:
- Core infrastucture work for Y2038 to address the COMPAT interfaces:
+ Add a new Y2038 safe __kernel_timespec and use it in the core
code
+ Introduce config switches which allow to control the various
compat mechanisms
+ Use the new config switch in the posix timer code to control the
32bit compat syscall implementation.
- Prevent bogus selection of CPU local clocksources which causes an
endless reselection loop
- Remove the extra kthread in the clocksource code which has no value
and just adds another level of indirection
- The usual bunch of trivial updates, cleanups and fixlets all over the
place
- More SPDX conversions
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
clocksource/drivers/mxs_timer: Switch to SPDX identifier
clocksource/drivers/timer-imx-tpm: Switch to SPDX identifier
clocksource/drivers/timer-imx-gpt: Switch to SPDX identifier
clocksource/drivers/timer-imx-gpt: Remove outdated file path
clocksource/drivers/arc_timer: Add comments about locking while read GFRC
clocksource/drivers/mips-gic-timer: Add pr_fmt and reword pr_* messages
clocksource/drivers/sprd: Fix Kconfig dependency
clocksource: Move inline keyword to the beginning of function declarations
timer_list: Remove unused function pointer typedef
timers: Adjust a kernel-doc comment
tick: Prefer a lower rating device only if it's CPU local device
clocksource: Remove kthread
time: Change nanosleep to safe __kernel_* types
time: Change types to new y2038 safe __kernel_* types
time: Fix get_timespec64() for y2038 safe compat interfaces
time: Add new y2038 safe __kernel_timespec
posix-timers: Make compat syscalls depend on CONFIG_COMPAT_32BIT_TIME
time: Introduce CONFIG_COMPAT_32BIT_TIME
time: Introduce CONFIG_64BIT_TIME in architectures
compat: Enable compat_get/put_timespec64 always
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull siginfo updates from Eric Biederman:
"This set of changes close the known issues with setting si_code to an
invalid value, and with not fully initializing struct siginfo. There
remains work to do on nds32, arc, unicore32, powerpc, arm, arm64, ia64
and x86 to get the code that generates siginfo into a simpler and more
maintainable state. Most of that work involves refactoring the signal
handling code and thus careful code review.
Also not included is the work to shrink the in kernel version of
struct siginfo. That depends on getting the number of places that
directly manipulate struct siginfo under control, as it requires the
introduction of struct kernel_siginfo for the in kernel things.
Overall this set of changes looks like it is making good progress, and
with a little luck I will be wrapping up the siginfo work next
development cycle"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
signal/sh: Stop gcc warning about an impossible case in do_divide_error
signal/mips: Report FPE_FLTUNK for undiagnosed floating point exceptions
signal/um: More carefully relay signals in relay_signal.
signal: Extend siginfo_layout with SIL_FAULT_{MCEERR|BNDERR|PKUERR}
signal: Remove unncessary #ifdef SEGV_PKUERR in 32bit compat code
signal/signalfd: Add support for SIGSYS
signal/signalfd: Remove __put_user from signalfd_copyinfo
signal/xtensa: Use force_sig_fault where appropriate
signal/xtensa: Consistenly use SIGBUS in do_unaligned_user
signal/um: Use force_sig_fault where appropriate
signal/sparc: Use force_sig_fault where appropriate
signal/sparc: Use send_sig_fault where appropriate
signal/sh: Use force_sig_fault where appropriate
signal/s390: Use force_sig_fault where appropriate
signal/riscv: Replace do_trap_siginfo with force_sig_fault
signal/riscv: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_mceerr where appropriate
signal/openrisc: Use force_sig_fault where appropriate
signal/nios2: Use force_sig_fault where appropriate
...
|
|
Pull documentation updates from Jonathan Corbet:
"There's been a fair amount of work in the docs tree this time around,
including:
- Extensive RST conversions and organizational work in the
memory-management docs thanks to Mike Rapoport.
- An update of Documentation/features from Andrea Parri and a script
to keep it updated.
- Various LICENSES updates from Thomas, along with a script to check
SPDX tags.
- Work to fix dangling references to documentation files; this
involved a fair number of one-liner comment changes outside of
Documentation/
... and the usual list of documentation improvements, typo fixes, etc"
* tag 'docs-4.18' of git://git.lwn.net/linux: (103 commits)
Documentation: document hung_task_panic kernel parameter
docs/admin-guide/mm: add high level concepts overview
docs/vm: move ksm and transhuge from "user" to "internals" section.
docs: Use the kerneldoc comments for memalloc_no*()
doc: document scope NOFS, NOIO APIs
docs: update kernel versions and dates in tables
docs/vm: transhuge: split userspace bits to admin-guide/mm/transhuge
docs/vm: transhuge: minor updates
docs/vm: transhuge: change sections order
Documentation: arm: clean up Marvell Berlin family info
Documentation: gpio: driver: Fix a typo and some odd grammar
docs: ranoops.rst: fix location of ramoops.txt
scripts/documentation-file-ref-check: rewrite it in perl with auto-fix mode
docs: uio-howto.rst: use a code block to solve a warning
mm, THP, doc: Add document for thp_swpout/thp_swpout_fallback
w1: w1_io.c: fix a kernel-doc warning
Documentation/process/posting: wrap text at 80 cols
docs: admin-guide: add cgroup-v2 documentation
Revert "Documentation/features/vm: Remove arch support status file for 'pte_special'"
Documentation: refcount-vs-atomic: Update reference to LKMM doc.
...
|
|
Pull dma-mapping updates from Christoph Hellwig:
- replace the force_dma flag with a dma_configure bus method. (Nipun
Gupta, although one patch is іncorrectly attributed to me due to a
git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few
cleanups to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
* tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits)
dma-direct: don't crash on device without dma_mask
nds32: use generic dma_noncoherent_ops
nds32: implement the unmap_sg DMA operation
nds32: consolidate DMA cache maintainance routines
x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag
x86/pci-dma: remove the explicit nodac and allowdac option
x86/pci-dma: remove the experimental forcesac boot option
Documentation/x86: remove a stray reference to pci-nommu.c
core, dma-direct: add a flag 32-bit dma limits
dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs
dma-debug: check scatterlist segments
c6x: use generic dma_noncoherent_ops
arc: use generic dma_noncoherent_ops
arc: fix arc_dma_{map,unmap}_page
arc: fix arc_dma_sync_sg_for_{cpu,device}
arc: simplify arc_dma_sync_single_for_{cpu,device}
dma-mapping: provide a generic dma-noncoherent implementation
dma-mapping: simplify Kconfig dependencies
riscv: add swiotlb support
riscv: only enable ZONE_DMA32 for 64-bit
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull procfs updates from Al Viro:
"Christoph's proc_create_... cleanups series"
* 'hch.procfs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (44 commits)
xfs, proc: hide unused xfs procfs helpers
isdn/gigaset: add back gigaset_procinfo assignment
proc: update SIZEOF_PDE_INLINE_NAME for the new pde fields
tty: replace ->proc_fops with ->proc_show
ide: replace ->proc_fops with ->proc_show
ide: remove ide_driver_proc_write
isdn: replace ->proc_fops with ->proc_show
atm: switch to proc_create_seq_private
atm: simplify procfs code
bluetooth: switch to proc_create_seq_data
netfilter/x_tables: switch to proc_create_seq_private
netfilter/xt_hashlimit: switch to proc_create_{seq,single}_data
neigh: switch to proc_create_seq_data
hostap: switch to proc_create_{seq,single}_data
bonding: switch to proc_create_seq_data
rtc/proc: switch to proc_create_single_data
drbd: switch to proc_create_single
resource: switch to proc_create_seq_data
staging/rtl8192u: simplify procfs code
jfs: simplify procfs code
...
|
|
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use new return type vm_fault_t for fault handler. For
now, this is just documenting that the function returns
a VM_FAULT value rather than an errno. Once all instances
are converted, vm_fault_t will become a distinct type.
commit 1c8f422059ae ("mm: change return type to vm_fault_t")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
By default, sparse assumes a 64bit machine when compiled on x86-64
and 32bit when compiled on anything else.
This can of course create all sort of problems for the other archs, like
issuing false warnings ('shift too big (32) for type unsigned long'), or
worse, failing to emit legitimate warnings.
Fix this by adding the -m32/-m64 flag, depending on CONFIG_64BIT,
to CHECKFLAGS in the main Makefile (and so for all archs).
Also, remove the now unneeded -m32/-m64 in arch specific Makefiles.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Use 64-bit accesses for 64-bit floating-point general registers with
PTRACE_PEEKUSR, removing the truncation of their upper halves in the
FR=1 mode, caused by commit bbd426f542cb ("MIPS: Simplify FP context
access"), which inadvertently switched them to using 32-bit accesses.
The PTRACE_POKEUSR side is fine as it's never been broken and continues
using 64-bit accesses.
Fixes: bbd426f542cb ("MIPS: Simplify FP context access")
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.15+
Patchwork: https://patchwork.linux-mips.org/patch/19334/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Having PR_FP_MODE_FRE (i.e. Config5.FRE) set without PR_FP_MODE_FR (i.e.
Status.FR) is not supported as the lone purpose of Config5.FRE is to
emulate Status.FR=0 handling on FPU hardware that has Status.FR=1
hardwired[1][2]. Also we do not handle this case elsewhere, and assume
throughout our code that TIF_HYBRID_FPREGS and TIF_32BIT_FPREGS cannot
be set both at once for a task, leading to inconsistent behaviour if
this does happen.
Return unsuccessfully then from prctl(2) PR_SET_FP_MODE calls requesting
PR_FP_MODE_FRE to be set with PR_FP_MODE_FR clear. This corresponds to
modes allowed by `mips_set_personality_fp'.
References:
[1] "MIPS Architecture For Programmers, Vol. III: MIPS32 / microMIPS32
Privileged Resource Architecture", Imagination Technologies,
Document Number: MD00090, Revision 6.02, July 10, 2015, Table 9.69
"Config5 Register Field Descriptions", p. 262
[2] "MIPS Architecture For Programmers, Volume III: MIPS64 / microMIPS64
Privileged Resource Architecture", Imagination Technologies,
Document Number: MD00091, Revision 6.03, December 22, 2015, Table
9.72 "Config5 Register Field Descriptions", p. 288
Fixes: 9791554b45a2 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options for MIPS")
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.0+
Patchwork: https://patchwork.linux-mips.org/patch/19327/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Correct comments across ptrace(2) handlers about an FPU register context
layout discrepancy between MIPS I and later ISAs, which was fixed with
`linux-mips.org' (LMO) commit 42533948caac ("Major pile of FP emulator
changes."), the fix corrected with LMO commit 849fa7a50dff ("R3k FPU
ptrace() handling fixes."), and then broken and fixed over and over
again, until last time fixed with commit 80cbfad79096 ("MIPS: Correct
MIPS I FP context layout").
NB running the GDB test suite for the relevant ABI/ISA and watching out
for regressions is advisable when poking around ptrace(2).
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19326/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Use the pci_info() and pci_err() wrappers for dev_printk() when possible.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: James Hogan <jhogan@kernel.org>
|
|
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Assembly language within the MIPS kernel conventionally indents
instructions which are in a branch delay slot to make them easier to
see. Commit 8483b14aaa81 ("MIPS: lib: memset: Whitespace fixes") rather
inexplicably removed all of these indentations from memset.S. Reinstate
the convention for all instructions in a branch delay slot. This
effectively reverts the above commit, plus other locations introduced
with MIPSR6 support.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19111/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Merge upstream to pick up changes on which pending patches depend on.
|
|
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: James Hogan <jhogan@kernel.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
|
|
Most mips builds fail with
arch/mips/kernel/traps.c: In function ‘force_fcr31_sig’:
arch/mips/kernel/traps.c:732:2: error:
‘si_code’ may be used uninitialized in this function
Fix the problem by initializing si_code with FPE_FLTUNK (undiagnosed
floating point exception).
Fixes: f43a54a0d916 ("signal/mips: Use force_sig_fault where appropriate")
Cc: linux-mips@linux-mips.org
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
|
|
Variants of proc_create{,_data} that directly take a seq_file show
callback and drastically reduces the boilerplate code in the callers.
All trivial callers converted over.
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
When perf is used in non-system mode, i.e. without specifying CPUs to
count on, check_and_calc_range falls into the case when it sets
M_TC_EN_ALL in the counter config_base. This has the impact of always
counting for all of the threads in a core, even when the user has not
requested it. For example this can be seen with a test program which
executes 30002 instructions and 10000 branches running on one VPE and a
busy load on the other VPE in the core. Without this commit, the
expected count is not returned:
taskset 4 dd if=/dev/zero of=/dev/null count=100000 & taskset 8 perf
stat -e instructions:u,branches:u ./test_prog
Performance counter stats for './test_prog':
103235 instructions:u
17015 branches:u
In order to fix this, remove check_and_calc_range entirely and perform
all of the logic in mipsxx_pmu_enable_event. Since
mipsxx_pmu_enable_event now requires the range of the event, ensure that
it is set by mipspmu_perf_event_encode in the same circumstances as
before (i.e. #ifdef CONFIG_MIPS_MT_SMP && num_possible_cpus() > 1).
The logic of mipsxx_pmu_enable_event now becomes:
If the CPU is a BMIPS5000, then use the special vpe_id() implementation
to select which VPE to count.
If the counter has a range greater than a single VPE, i.e. it is a
core-wide counter, then ensure that the counter is set up to count
events from all TCs (though, since this is true by definition, is this
necessary? Just enabling a core-wide counter in the per-VPE case appears
experimentally to return the same counts. This is left in for now as the
logic was present before).
If the event is set up to count a particular CPU (i.e. system mode),
then the VPE ID of that CPU is used for the counter.
Otherwise, the event should be counted on the CPU scheduling this thread
(this was the critical bit missing from the previous implementation) so
the VPE ID of this CPU is used for the counter.
With this commit, the same test as before returns the counts expected:
taskset 4 dd if=/dev/zero of=/dev/null count=100000 & taskset 8 perf
stat -e instructions:u,branches:u ./test_prog
Performance counter stats for './test_prog':
30002 instructions:u
10000 branches:u
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19138/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
There are a couple of FIXME's in the perf code which state that
cpu_data[event->cpu].vpe_id reports 0 for both CPUs. This is no longer
the case, since the vpe_id is used extensively by SMP CPS.
VPE local counting gets around this by using smp_processor_id() instead.
As it happens this does work correctly to count events on the right VPE,
but relies on 2 assumptions:
a) Always having 2 VPEs / core.
b) The hardware only paying attention to the least significant bit of
the PERFCTL.VPEID field.
If either of these assumptions change then the incorrect VPEs events
will be counted.
Fix this by replacing smp_processor_id() with
cpu_vpe_id(¤t_cpu_data), in the vpe_id() macro, and pass vpe_id()
to M_PERFCTL_VPEID() when setting up PERFCTL.VPEID. The FIXME's can also
be removed since they no longer apply.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19137/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
The presence of per TC performance counters is now detected by
cpu-probe.c and indicated by MIPS_CPU_MT_PER_TC_PERF_COUNTERS in
cpu_data. Switch detection of the feature to use this new flag rather
than blindly testing the implementation specific config7 register with a
magic number.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Maciej W. Rozycki <macro@mips.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Robert Richter <rric@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: oprofile-list@lists.sf.net
Patchwork: https://patchwork.linux-mips.org/patch/19142/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Processors implementing the MIPS MT ASE may have performance counters
implemented per core or per TC. Processors implemented by MIPS
Technologies signify presence per TC through a bit in the implementation
specific Config7 register. Currently the code which probes for their
presence blindly reads a magic number corresponding to this bit, despite
it potentially having a different meaning in the CPU implementation.
Since CPU features are generally detected by cpu-probe.c, perform the
detection here instead. Introduce cpu_set_mt_per_tc_perf which checks
the bit in config7 and call it from MIPS CPUs known to implement this
bit and the MT ASE, specifically, the 34K, 1004K and interAptiv.
Once the presence of the per-tc counter is indicated in cpu_data, tests
for it can be updated to use this flag.
Suggested-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Maciej W. Rozycki <macro@mips.com>
Cc: linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/19136/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
The ool_skb_header_pointer() and size_to_len() is unused same as
tmp_offset, therefore remove all of them.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add phy to switch port connections for PCB123 for internal PHYs.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Ocelot has an integrated switch, add support for it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
This work is now performed by the watchdog driver directly.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
The watchdog is an useful piece of hardware, so there's no reason not to
enable it.
Besides, this is important for restart to work after the change in the
next commit.
This commit enables the Kconfig option in the qi_lb60 defconfig.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
- The previous node requested a memory area of 0x100 bytes, while the
driver only manipulates four registers present in the first 0x10 bytes.
- The driver requests for the "rtc" clock, but the previous node did not
provide any.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Mathieu Malaterre <malat@debian.org>
Acked-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Also remove the watchdog platform_device from platform.c, since it
wasn't used anywhere anyway.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree@vger.kernel.org
[jhogan@kernel.org: Drop jz4740_wdt_device declaration from header]
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Trivial fix to spelling mistake in pr_warn message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kernel-janitors@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Re-use kstrtobool_from_user() instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Since struct timespec is not y2038 safe on 32bit machines, this patch
converts update_persistent_clock() to update_persistent_clock64() using
struct timespec64.
The rtc_mips_set_time() and rtc_mips_set_mmss() interfaces were using
'unsigned long' type that is not y2038 safe on 32bit machines, moreover
there is only one platform implementing rtc_mips_set_time() and two
platforms implementing rtc_mips_set_mmss(), so we can just make them each
implement update_persistent_clock64() directly, to get that helper out
of the common mips code by removing rtc_mips_set_time() and
rtc_mips_set_mmss() interfaces.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Since struct timespec is not y2038 safe on 32bit machines, this patch
converts read_persistent_clock() to read_persistent_clock64() using
struct timespec64, as well as converting mktime() to mktime64().
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
The dummy read_persistent_clock() uses a timespec, which is not year
2038 safe on 32bit systems. Thus remove this obsolete interface.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19114/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Check the TIF_32BIT_FPREGS task setting of the tracee rather than the
tracer in determining the layout of floating-point general registers in
the floating-point context, correcting access to odd-numbered registers
for o32 tracees where the setting disagrees between the two processes.
Fixes: 597ce1723e0f ("MIPS: Support for 64-bit FP with O32 binaries")
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Commit b35565bb16a5 ("MIPS: generic: Add support for MIPSfpga") added
and its.S file for xilfpga but forgot to add it to
arch/mips/generic/Platform so it is never used.
Fixes: b35565bb16a5 ("MIPS: generic: Add support for MIPSfpga")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.15+
Patchwork: https://patchwork.linux-mips.org/patch/19245/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
A dtb.o is generated from nexys4ddr.dts but this is never used since it
has been moved to mips/generic with commit b35565bb16a5 ("MIPS: generic:
Add support for MIPSfpga").
Fixes: b35565bb16a5 ("MIPS: generic: Add support for MIPSfpga")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.15+
Patchwork: https://patchwork.linux-mips.org/patch/19244/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Trivial fix to spelling mistake in debugfs_entries text.
Fixes: 669e846e6c4e ("KVM/MIPS32: MIPS arch specific APIs for KVM")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kernel-janitors@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
Correct commit 7aeb753b5353 ("MIPS: Implement task_user_regset_view.")
and expose the FIR register using the unused 4 bytes at the end of the
NT_PRFPREG regset. Without that register included clients cannot use
the PTRACE_GETREGSET request to retrieve the complete FPU register set
and have to resort to one of the older interfaces, either PTRACE_PEEKUSR
or PTRACE_GETFPREGS, to retrieve the missing piece of data. Also the
register is irreversibly missing from core dumps.
This register is architecturally hardwired and read-only so the write
path does not matter. Ignore data supplied on writes then.
Fixes: 7aeb753b5353 ("MIPS: Implement task_user_regset_view.")
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.13+
Patchwork: https://patchwork.linux-mips.org/patch/19273/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
The debug definitions were missing for MACH_JZ4770, resulting in a build
failure when DEBUG_ZBOOT was set.
Since the UART addresses are the same across all Ingenic SoCs, we just
use a #ifdef CONFIG_MACH_INGENIC instead of checking for individual
Ingenic SoCs.
Additionally, I added a #define for the UART0 address in-code and
dropped the <asm/mach-jz4740/base.h> include, for the reason that this
include file is slowly being phased out as the whole platform is being
moved to devicetree.
Fixes: 9be5f3e92ed5 ("MIPS: ingenic: Initial JZ4770 support")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.16
Patchwork: https://patchwork.linux-mips.org/patch/18957/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
When DMA will be performed to a MIPS32 1004K CPS, the L1-cache for the
range needs to be flushed and invalidated first.
The code currently takes one of two approaches.
1/ If the range is less than the size of the dcache, then HIT type
requests flush/invalidate cache lines for the particular addresses.
HIT-type requests a globalised by the CPS so this is safe on SMP.
2/ If the range is larger than the size of dcache, then INDEX type
requests flush/invalidate the whole cache. INDEX type requests affect
the local cache only. CPS does not propagate them in any way. So this
invalidation is not safe on SMP CPS systems.
Data corruption due to '2' can quite easily be demonstrated by
repeatedly "echo 3 > /proc/sys/vm/drop_caches" and then sha1sum a file
that is several times the size of available memory. Dropping caches
means that large contiguous extents (large than dcache) are more likely.
This was not a problem before Linux-4.8 because option 2 was never used
if CONFIG_MIPS_CPS was defined. The commit which removed that apparently
didn't appreciate the full consequence of the change.
We could, in theory, globalize the INDEX based flush by sending an IPI
to other cores. These cache invalidation routines can be called with
interrupts disabled and synchronous IPI require interrupts to be
enabled. Asynchronous IPI may not trigger writeback soon enough. So we
cannot use IPI in practice.
We can already test if IPI would be needed for an INDEX operation with
r4k_op_needs_ipi(R4K_INDEX). If this is true then we mustn't try the
INDEX approach as we cannot use IPI. If this is false (e.g. when there
is only one core and hence one L1 cache) then it is safe to use the
INDEX approach without IPI.
This patch avoids options 2 if r4k_op_needs_ipi(R4K_INDEX), and so
eliminates the corruption.
Fixes: c00ab4896ed5 ("MIPS: Remove cpu_has_safe_index_cacheops")
Signed-off-by: NeilBrown <neil@brown.name>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.8+
Patchwork: https://patchwork.linux-mips.org/patch/19259/
Signed-off-by: James Hogan <jhogan@kernel.org>
|
|
This way we have one central definition of it, and user can select it as
needed. The new option is not user visible, which is the behavior
it had in most architectures, with a few notable exceptions:
- On x86_64 and mips/loongson3 it used to be user selectable, but
defaulted to y. It now is unconditional, which seems like the right
thing for 64-bit architectures without guaranteed availablity of
IOMMUs.
- on powerpc the symbol is user selectable and defaults to n, but
many boards select it. This change assumes no working setup
required a manual selection, but if that turned out to be wrong
we'll have to add another select statement or two for the respective
boards.
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Only mips and unicore32 select CONFIG_NEED_SG_DMA_LENGTH when building
swiotlb. swiotlb itself never merges segements and doesn't accesses the
dma_length field directly, so drop the dependency.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: James Hogan <jhogan@kernel.org>
|
|
Define this symbol if the architecture either uses 64-bit pointers or the
PHYS_ADDR_T_64BIT is set. This covers 95% of the old arch magic. We only
need an additional select for Xen on ARM (why anyway?), and we now always
set ARCH_DMA_ADDR_T_64BIT on mips boards with 64-bit physical addressing
instead of only doing it when highmem is set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: James Hogan <jhogan@kernel.org>
|
|
Instead select the PHYS_ADDR_T_64BIT for 32-bit architectures that need a
64-bit phys_addr_t type directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: James Hogan <jhogan@kernel.org>
|
|
This way we have one central definition of it, and user can select it as
needed. Note that we now also always select it when CONFIG_DMA_API_DEBUG
is select, which fixes some incorrect checks in a few network drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
|
|
This way we have one central definition of it, and user can select it as
needed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
|
|
This avoids selecting IOMMU_HELPER just for this function. And we only
use it once or twice in normal builds so this often even is a size
reduction.
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
