summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)AuthorFilesLines
2018-09-26ARM: tegra: colibri_t30: add missing regulatorsMarcel Ziswiler2-1/+30
Add missing regulators: - reg_module_3v3_audio being VDDA supply of SGTL5000 - VDDD supply of SGTL5000 actually being reg_1v8_vio - reg_lan_v_bus being USB Ethernet chip vbus supply - carrier board HDMI supply being reg_5v0 - carrier board reg_3v3 actually being backlight and panel power supply Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: colibri_t30: regulator clean-upMarcel Ziswiler2-100/+78
Just cosmetic regulator clean-up. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: colibri_t30: reorder host1x/hdmi propertiesMarcel Ziswiler1-4/+3
Reorder Host1x/HDMI properties. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: colibri_t30: add local-mac-address propertyMarcel Ziswiler1-0/+7
Add empty local-mac-address property to be filled in by boot loader (e.g. U-Boot). Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: support v1.1 hardware revisionMarcel Ziswiler4-2/+1457
Support the V1.1 hardware revisions with the following change: Changed power rail for MMC1 interface to a 3.3V/1.8V switchable rail in order to be able to run UHS SD cards in ultra high speed 1.8V mode. [ 207.502011] mmc2: host does not support reading read-only switch, assuming write-enable [ 207.517011] mmc2: new ultra high speed SDR104 SDHC card at address aaaa [ 207.534190] mmcblk2: mmc2:aaaa SE32G 29.7 GiB [ 207.545096] mmcblk2: p1 root@apalis-t30:~# cat /sys/kernel/debug/mmc2/ios clock: 208000000 Hz actual clock: 204000000 Hz vdd: 21 (3.3 ~ 3.4 V) bus mode: 2 (push-pull) chip select: 0 (don't care) power mode: 2 (on) bus width: 2 (4 bits) timing spec: 6 (sd uhs SDR104) signal voltage: 1 (1.80 V) driver type: 0 (driver type B) root@apalis-t30:~# hdparm -t /dev/mmcblk2 /dev/mmcblk2: Timing buffered disk reads: 256 MB in 3.02 seconds = 84.71 MB/sec Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: move hda node from carrier to moduleMarcel Ziswiler2-4/+4
Move the hda node from the carrier board to the module level device tree. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: fix mcp2515 can controller interrupt polarityMarcel Ziswiler1-2/+2
Fix the MCP2515 SPI CAN controller interrupt polarity which according to its datasheet defaults to low-active aka falling edge. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: rename tps65911@2d, stmpe811@41 and tps62362@60Marcel Ziswiler2-4/+4
Rename a few nodes using more common names: - rename tps65911@2d to pmic@2d - rename stmpe811@41 to touchscreen@41 - rename tps62362@60 to regulator@60 Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: rename hdmiddc to hdmi_ddcMarcel Ziswiler2-3/+3
Rename hdmiddc to hdmi_ddc to be more in-line with other device trees. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: hog group for pcie switch reset gpioMarcel Ziswiler1-0/+10
The Apalis Evaluation Board uses Apalis GPIO7 on MXM3 pin 15 as reset signal for its PLX PEX 8605 PCIe Switch. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: drop obsolete spidev nodesMarcel Ziswiler1-12/+0
Drop obsolete spidev device tree nodes as nowadays one should do this by binding the spidev driver to specific instances/chip selects at runtime. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: drop module level model and compatibleMarcel Ziswiler1-3/+0
Drop model and compatible nodes from the module level device tree as they get overridden by the carrier board device tree anyway. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: line break long compatible property lineMarcel Ziswiler1-1/+2
Line break long compatible property line. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: get rid of fake clocks simple busMarcel Ziswiler1-18/+9
Get rid of the fake clocks simple bus and use node names as per the actual schematics. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: enable emmc ddr52 modeMarcel Ziswiler1-0/+1
Add mmc-ddr-1_8v property enabling eMMC DDR52 mode. root@apalis-t30:~# cat /sys/kernel/debug/mmc1/ios clock: 52000000 Hz actual clock: 52000000 Hz vdd: 21 (3.3 ~ 3.4 V) bus mode: 2 (push-pull) chip select: 0 (don't care) power mode: 2 (on) bus width: 3 (8 bits) timing spec: 8 (mmc DDR52) signal voltage: 1 (1.80 V) driver type: 0 (driver type B) root@apalis-t30:~# hdparm -t /dev/mmcblk1 /dev/mmcblk1: Timing buffered disk reads: 232 MB in 3.01 seconds = 77.10 MB/sec Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: add proper emmc vmmc and vqmmc suppliesMarcel Ziswiler1-0/+2
Add proper eMMC vmmc and vqmmc supplies e.g. fixing signalling voltage. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: add i2c-thermtripMarcel Ziswiler1-0/+8
Add i2c-thermtrip which would set the DEV_OFF bit in the DCDC control register of the TPS65911 PMIC. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: further lm95245 temperature sensor annotationMarcel Ziswiler1-1/+1
Further LM95245 temperature sensor annotation. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: use proper irq-gpio for stmpe811Marcel Ziswiler1-2/+1
Use proper irq-gpio for stmpe811 touch controller. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: add missing pinmuxMarcel Ziswiler1-0/+370
Explicitly mux all T30 SoC balls now: - Apalis GPIO - Apalis HDMI1 - Apalis I2C1 - Apalis I2C2 (DDC) - Apalis LCD1 - Apalis Parallel Camera - Apalis SATA1_ACT# - Apalis SPDIF1 - Apalis TS (Low-speed type specific) - Apalis USBH_EN - Apalis USBH_OC# - Apalis VGA1 - on-module i210/i211 LAN control signals - not connected and therefore disabled signals Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: pinmux clean-upMarcel Ziswiler1-43/+45
Clean-up pinmuxing: - white-space clean-up - explicitly disable input of BKL1_ON, BKL1_PWM and BKL1_PWM_EN# - annotate Apalis I2C3 usage for CAM - get rid of nvidia,lock property - add missing eMMC sdmmc4_cmd_pt7 and explicitly enable input - explicitly disable lcd_dc1_pd2 (e.g. LM95245 I2C address pin) - annotate TOUCH_PEN_INT# being on-module - As underscores in node names are not recommended replace them all where possible with dashes. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: drop pwmledsMarcel Ziswiler1-22/+0
Drop pwmleds in favour of using regular PWMs. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: reorder backlight propertiesMarcel Ziswiler1-2/+1
Reorder backlight properties. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: move dr_mode property from phy to controllerMarcel Ziswiler1-1/+1
Move dr_mode property from USB PHY node to controller. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: annotate mmc1/sd1Marcel Ziswiler1-0/+2
Annotate MMC1/SD1. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: drop unused mmc1/sd1 labelsMarcel Ziswiler1-2/+2
Drop unused mmc1/sd1 labels. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: white-space/newline clean-upMarcel Ziswiler2-2/+4
White-space and newline clean-up. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: drop unused cami2c labelMarcel Ziswiler1-1/+1
Drop unused cami2c label. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: annotate uarts and move compatible to boardMarcel Ziswiler2-3/+16
Annotate UARTs and move the serial UART "nvidia,tegra30-hsuart" compatible definitions from the carrier board to the module level device trees. One could still override this in a custom carrier board device tree if required. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: add missing regulatorsMarcel Ziswiler2-1/+20
Add missing regulators: - reg_module_3v3_audio being VDDA supply of SGTL5000 - VDDD supply of SGTL5000 actually being reg_1v8_vio - carrier board HDMI supply being reg_5v0 - carrier board reg_3v3 actually being backlight and panel power supply Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: regulator clean-upMarcel Ziswiler2-114/+88
Just cosmetic regulator clean-up. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: reorder host1x/hdmi propertiesMarcel Ziswiler1-4/+3
Reorder Host1x/HDMI properties. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: annotate/clean-up pcie controller/port nodesMarcel Ziswiler2-6/+5
Annotate PCIe port nodes and clean-up PCIe controller/port status' with respect to carrier board vs. module level device trees. As port 3 connects to the on-module Gigabit Ethernet MACPHY it is always enabled together with the PCIe controller itself. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: reorder pcie propertiesMarcel Ziswiler1-3/+3
Reorder PCIe properties. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: add local-mac-address propertyMarcel Ziswiler1-0/+4
Add empty local-mac-address property to be filled in by boot loader (e.g. U-Boot). Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: pull-up sd card detect pinsMarcel Ziswiler1-2/+2
In order to avoid any floating SD card detect pins as may e.g. happen on Ixora V1.1A pull them all up. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: tegra: apalis_t30: fix mmc1 cmd pull-upMarcel Ziswiler1-3/+3
Fix MMC1 cmd pin pull-up causing issues on carrier boards without external pull-up. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: dts: tegra20/tegra30: add pmu interrupt-affinityMarcel Ziswiler2-0/+6
This is similar to tegra124 and avoids the following being reported upon boot: hw perfevents: no interrupt-affinity property for /pmu, guessing. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: dts: tegra20: restore address orderMarcel Ziswiler1-13/+13
Commit 6c468f109884 ("ARM: dts: tegra: add Tegra20 NAND flash controller node") introduced the nand-controller node. However, it got added at the wrong spot not honoring the address order. Fix this. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-09-26ARM: dts: tegra30: fix xcvr-setup-use-fusesMarcel Ziswiler1-3/+3
There was a dot instead of a comma. Fix this. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2018-08-26Merge tag 'armsoc-late' of ↵Linus Torvalds1-0/+1
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC late updates from Olof Johansson: "A couple of late-merged changes that would be useful to get in this merge window: - Driver support for reset of audio complex on Meson platforms. The audio driver went in this merge window, and these changes have been in -next for a while (just not in our tree). - Power management fixes for IOMMU on Rockchip platforms, getting closer to kexec working on them, including Chromebooks. - Another pass updating "arm,psci" -> "psci" for some properties that have snuck in since last time it was done" * tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: iommu/rockchip: Move irq request past pm_runtime_enable iommu/rockchip: Handle errors returned from PM framework arm64: rockchip: Force CONFIG_PM on Rockchip systems ARM: rockchip: Force CONFIG_PM on Rockchip systems arm64: dts: Fix various entry-method properties to reflect documentation reset: imx7: Fix always writing bits as 0 reset: meson: add meson audio arb driver reset: meson: add dt-bindings for meson-axg audio arb
2018-08-25Merge tag 'kbuild-v4.19-2' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull more Kbuild updates from Masahiro Yamada: - add build_{menu,n,g,x}config targets for compile-testing Kconfig - fix and improve recursive dependency detection in Kconfig - fix parallel building of menuconfig/nconfig - fix syntax error in clang-version.sh - suppress distracting log from syncconfig - remove obsolete "rpm" target - remove VMLINUX_SYMBOL(_STR) macro entirely - fix microblaze build with CONFIG_DYNAMIC_FTRACE - move compiler test for dead code/data elimination to Kconfig - rename well-known LDFLAGS variable to KBUILD_LDFLAGS - misc fixes and cleanups * tag 'kbuild-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: kbuild: rename LDFLAGS to KBUILD_LDFLAGS kbuild: pass LDFLAGS to recordmcount.pl kbuild: test dead code/data elimination support in Kconfig initramfs: move gen_initramfs_list.sh from scripts/ to usr/ vmlinux.lds.h: remove stale <linux/export.h> include export.h: remove VMLINUX_SYMBOL() and VMLINUX_SYMBOL_STR() Coccinelle: remove pci_alloc_consistent semantic to detect in zalloc-simple.cocci kbuild: make sorting initramfs contents independent of locale kbuild: remove "rpm" target, which is alias of "rpm-pkg" kbuild: Fix LOADLIBES rename in Documentation/kbuild/makefiles.txt kconfig: suppress "configuration written to .config" for syncconfig kconfig: fix "Can't open ..." in parallel build kbuild: Add a space after `!` to prevent parsing as file pattern scripts: modpost: check memory allocation results kconfig: improve the recursive dependency report kconfig: report recursive dependency involving 'imply' kconfig: error out when seeing recursive dependency kconfig: add build-only configurator targets scripts/dtc: consolidate include path options in Makefile
2018-08-24ARM: rockchip: Force CONFIG_PM on Rockchip systemsMarc Zyngier1-0/+1
A number of the Rockchip-specific drivers (IOMMU, display controllers) are now assuming that CONFIG_PM is set, and may completely misbehave if that's not the case. Since there is hardly any reason for this configuration option not to be selected anyway, let's require it (in the same way Tegra already does). Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2018-08-24Merge branch 'akpm' (patches from Andrew)Linus Torvalds3-4/+4
Merge yet more updates from Andrew Morton: - the rest of MM - various misc fixes and tweaks * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits) mm: Change return type int to vm_fault_t for fault handlers lib/fonts: convert comments to utf-8 s390: ebcdic: convert comments to UTF-8 treewide: convert ISO_8859-1 text comments to utf-8 drivers/gpu/drm/gma500/: change return type to vm_fault_t docs/core-api: mm-api: add section about GFP flags docs/mm: make GFP flags descriptions usable as kernel-doc docs/core-api: split memory management API to a separate file docs/core-api: move *{str,mem}dup* to "String Manipulation" docs/core-api: kill trailing whitespace in kernel-api.rst mm/util: add kernel-doc for kvfree mm/util: make strndup_user description a kernel-doc comment fs/proc/vmcore.c: hide vmcoredd_mmap_dumps() for nommu builds treewide: correct "differenciate" and "instanciate" typos fs/afs: use new return type vm_fault_t drivers/hwtracing/intel_th/msu.c: change return type to vm_fault_t mm: soft-offline: close the race against page allocation mm: fix race on soft-offlining free huge pages namei: allow restricted O_CREAT of FIFOs and regular files hfs: prevent crash on exit from failed search ...
2018-08-24treewide: convert ISO_8859-1 text comments to utf-8Arnd Bergmann3-4/+4
Almost all files in the kernel are either plain text or UTF-8 encoded. A couple however are ISO_8859-1, usually just a few characters in a C comments, for historic reasons. This converts them all to UTF-8 for consistency. Link: http://lkml.kernel.org/r/20180724111600.4158975-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Simon Horman <horms@verge.net.au> [IPVS portion] Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> [IIO] Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc] Acked-by: Rob Herring <robh@kernel.org> Cc: Joe Perches <joe@perches.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rob Herring <robh+dt@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-08-24kbuild: rename LDFLAGS to KBUILD_LDFLAGSMasahiro Yamada1-2/+2
Commit a0f97e06a43c ("kbuild: enable 'make CFLAGS=...' to add additional options to CC") renamed CFLAGS to KBUILD_CFLAGS. Commit 222d394d30e7 ("kbuild: enable 'make AFLAGS=...' to add additional options to AS") renamed AFLAGS to KBUILD_AFLAGS. Commit 06c5040cdb13 ("kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP") renamed CPPFLAGS to KBUILD_CPPFLAGS. For some reason, LDFLAGS was not renamed. Using a well-known variable like LDFLAGS may result in accidental override of the variable. Kbuild generally uses KBUILD_ prefixed variables for the internally appended options, so here is one more conversion to sanitize the naming convention. I did not touch Makefiles under tools/ since the tools build system is a different world. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
2018-08-24Merge tag 'armsoc-dt' of ↵Linus Torvalds379-4252/+15632
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM device-tree updates from Olof Johansson: "Business as usual -- the bulk of our changes are to devicetree files with new hardware support, new SoCs and platforms, and new board types. New SoCs/platforms: - Raspberry Pi Compute Module (CM1) and IO board - i.MX6SSL from NXP - Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN and PLC interfaces - TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5 controllers, communication and PRU subsystem and lots of other interfaces (PCIe, USB3, etc). New boards and systems: - Several Atmel at91-based boards from Laird - Marvell Armada388-based Helios4 board from SolidRun - Samsung Aires-based phones (s5pv210) - Allwinner A64-based Pinebook laptop In addition to the above, there's the usual amount of new devices described on existing platforms, fixes and tweaks and new minor variants of boards/platforms" * tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits) arm64: dts: sdm845: Add tsens nodes arm64: dts: msm8996: thermal: Initialise via DT and add second controller arm64: dts: sprd: Add one suspend timer arm64: dts: sprd: Add SC27XX ADC device arm64: dts: sprd: Add SC27XX eFuse device arm64: dts: sprd: Add SC27XX vibrator device arm64: dts: sprd: Add SC27XX breathing light controller device arm64: dts: meson-axg: add spdif-dit codec arm64: dts: meson-axg: add lineout codec arm64: dts: meson-axg: add linein codec arm64: dts: meson-axg: add tdm interfaces arm64: dts: meson-axg: add tdmout formatters arm64: dts: meson-axg: add tdmin formatters arm64: dts: meson-axg: add spdifout arm64: dts: rockchip: add led support for Firefly-RK3399 arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399 arm64: dts: rockchip: add power button support for Firefly-RK3399 ARM: dts: aspeed: Add coprocessor interrupt controller arm64: dts: meson-axg: add audio arb reset controller arm64: dts: meson-axg: add usb power regulator ...
2018-08-24Merge tag 'armsoc-defconfig' of ↵Linus Torvalds13-81/+301
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC defconfig updates from Olof Johansson: "We keep these separate since some files are shared and conflict-prone, but there isn't really much to write about here. Some of the churnier pieces is for the Aspeed platforms, which did an overdue refresh of the defconfig, and enabled USB gadget and some drivers from there. Most of the rest are minor additions here and there to turn on drivers that are needed or useful on the various platforms" * tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits) ARM: multi_v7_defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE ARM: config: aspeed: Enable new FSI drivers ARM: config: multi_v5: Enable ASPEED drivers ARM: config: multi_v5: Refresh configuration ARM: config: aspeed: Update defconfig ARM: multi_v7_defconfig: Enable support for RZN1D-DB ARM: shmobile: defconfig: Disable /sbin/hotplug fork-bomb ARM: shmobile: defconfig: Enable support for RZN1D-DB ARM: shmobile: defconfig: Enable reset controller support ARM: shmobile: defconfig: Drop NET_VENDOR_<FOO>=n arm64: defconfig: Enable more peripherals for Samsung Chromebook Plus. arm64: defconfig: Enable CONFIG_MTD_NAND_QCOM for IPQ8074 ARM: qcom_defconfig: Enable QCOM NAND related configs ARM: imx_v6_v7_defconfig: add DMATEST support ARM: mvebu_v7_defconfig: enable SFP support ARM: mvebu_v7_defconfig: sync defconfig ARM: multi_v7_defconfig: Add Marvell NAND controller support arm: configs: Add USB gadget to Aspeed G5 defconfig arm: configs: Add USB gadget to Aspeed G4 defconfig arm64: defconfig: enable HiSilicon PMU driver ...
2018-08-23Merge tag 'armsoc-soc' of ↵Linus Torvalds112-5195/+2098
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM 32-bit SoC platform updates from Olof Johansson: "Most of the SoC updates in this cycle are cleanups and moves to more modern infrastructure: - Davinci was moved to common clock framework - OMAP1-based Amstrad E3 "Superphone" saw a bunch of cleanups to the keyboard interface (bitbanged AT keyboard via GPIO). - Removal of some stale code for Renesas platforms - Power management improvements for i.MX6LL" * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (112 commits) ARM: uniphier: select RESET_CONTROLLER arm64: uniphier: select RESET_CONTROLLER ARM: uniphier: remove empty Makefile ARM: exynos: Clear global variable on init error path ARM: exynos: Remove outdated maintainer information ARM: shmobile: Always enable ARCH_TIMER on SoCs with A7 and/or A15 ARM: shmobile: r8a7779: hide unused r8a7779_platform_cpu_kill soc: r9a06g032: don't build SMP files for non-SMP config ARM: shmobile: Add the R9A06G032 SMP enabler driver ARM: at91: pm: configure wakeup sources for ULP1 mode ARM: at91: pm: add PMC fast startup registers defines ARM: at91: pm: Add ULP1 mode support ARM: at91: pm: Use ULP0 naming instead of slow clock ARM: hisi: handle of_iomap and fix missing of_node_put ARM: hisi: check of_iomap and fix missing of_node_put ARM: hisi: fix error handling and missing of_node_put ARM: mx5: Set the DBGEN bit in ARM_GPC register ARM: imx51: Configure M4IF to avoid visual artifacts ARM: imx: call imx6sx_cpuidle_init() conditionally for 6sll ARM: imx: fix i.MX6SLL build ...
2018-08-23include/linux/compiler*.h: make compiler-*.h mutually exclusiveNick Desaulniers1-12/+1
Commit cafa0010cd51 ("Raise the minimum required gcc version to 4.6") recently exposed a brittle part of the build for supporting non-gcc compilers. Both Clang and ICC define __GNUC__, __GNUC_MINOR__, and __GNUC_PATCHLEVEL__ for quick compatibility with code bases that haven't added compiler specific checks for __clang__ or __INTEL_COMPILER. This is brittle, as they happened to get compatibility by posing as a certain version of GCC. This broke when upgrading the minimal version of GCC required to build the kernel, to a version above what ICC and Clang claim to be. Rather than always including compiler-gcc.h then undefining or redefining macros in compiler-intel.h or compiler-clang.h, let's separate out the compiler specific macro definitions into mutually exclusive headers, do more proper compiler detection, and keep shared definitions in compiler_types.h. Fixes: cafa0010cd51 ("Raise the minimum required gcc version to 4.6") Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com> Suggested-by: Eli Friedman <efriedma@codeaurora.org> Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-02-11 22:37:40 +0300