| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On 66AK2G EVM mmc1 is connected to emmc whereas 66AK2G ICE baord has SD
card slot connected to mmc1. Therefore move emmc specific
ti,non-removable property from SoC file to EVM's dts file.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
spi1 and ecap0 pinmuxes ended up under root node instead of k2g_pinctrl
node. Fix this by moving them under k2g_pinctrl node.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Add DT node for Cadence QSPI IP present in 66AK2G SoC.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
In case of k2l there are 2 more banks with 16 pins each.
Adding the node as the da-vinci driver now supports multiple
banks.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.15:
- A fix for vf610-zii-dev-rev-c board which correct the unit-address
of I2C EEPROM node to match the 'reg' property.
- We thought the RTC block on i.MX53 is compatible with the one found
on i.MX25, and added the device for i.MX53 device tree. But it turns
out that's not the case, and we have to revert the change.
* tag 'imx-fixes-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
Revert "ARM: dts: imx53: add srtc node"
ARM: dts: vf610-zii-dev-rev-c: Fix the I2C EEPROM address
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.15,
please pull the following:
- Stefan provides a fix for the BCM2835 (Raspberry Pi) to fix warnings about
missing "#phy-cells" properties
- Florian provides two fixes for Nortsthar Plus, one that uses the correct
interrupt specifiers for the timer/watchdog and one that disables SATA
on BCM9582**HR boards since that leads to unidentified hangs right now
* tag 'arm-soc/for-4.15/devicetree-fixes-1' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: Fix PPI interrupt types
ARM: dts: NSP: Disable AHCI controller for HR NSP boards
ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC DT Fixes for v4.15
Add missing '#reset-cells' property to cpg nodes.
This flagged by recent dtc.
* tag 'renesas-dt-fixes-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a779x: Add '#reset-cells' in cpg-mssr
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in Marvell dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The rk3066 also has operating points now, but without adjusting
the cpu-regulator will break once higher voltages are needed for
a specific frequency, so add the needed cpu0-regulator.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds the device nodes for flexcan controller(s) present on
LS1021A-Rev2 SoC.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Sakar Arora <Sakar.Arora@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
Reviewed-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The flexcan driver has been modified to check for big-endian dts
property for be read/write to flexcan registers/mb.
An exception to this rule is powerpc P1010RDB, which is always
big-endian, even if big-endian is not present in dts. This is
checked using p1010-flexcan compatible in dts.
Therefore, remove p1010-flexcan compatible from imx series dts,
as their flexcan core is little endian.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Trivial fix to spelling mistake in pr_err error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
commit 200a575b68d2 ("ARM: dts: meson: organize devices in their corresponding busses")
organized all peripherals in busses so that the base register offset of
the bus doesn't have to be included in all child-nodes anymore.
The GPIO interrupt controller however specifies the register offset
without subtracting the "cbus" base address. This leads to a problem
where of_iomap inside the irq-meson-gpio driver fails because it
actually tries to map 0x182209880 (cbus base = 0xc1100000 + 0xc1109880
for the GPIO interrupt controller). Fix this by using 0x9880 as register
offset.
Fixes: 7d32bc03bcfb ("ARM: dts: meson8b: enable gpio interrupt controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Nodes are sorted by their register start address. Move gpio_intc to the
correct position.
No functional changes intended.
Fixes: 7d32bc03bcfb ("ARM: dts: meson8b: enable gpio interrupt controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable following drivers for recently merged devices:
- CEC and S5P CEC driver for all Exynos4 and Exynos5 boards with HDMI
- Sii9234 DRM HDMI-MHL bridge for Trats2
- dedicated Odroid ASoC machine driver for Odroid XU3/XU4
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Enable following drivers for recently merged devices:
- perf events and ARM PMU (Performance Measurement Unit) driver for all
Exynos boards
- CEC and S5P CEC driver for all Exynos4 and Exynos5 boards with HDMI
- Sii9234 DRM HDMI-MHL bridge for Trats2
- dedicated Odroid ASoC machine driver for Odroid XU3/XU4
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 14e3e295b2b9 ("ARM: dts: omap3-n900: Add TLV320AIC3X support")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 4341881d0562 ("ARM: dts: Add devicetree for Gumstix Pepper board")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
In response to compile breakage introduced by a series that added the
pud_write helper to x86, Stephen notes:
did you consider using the other paradigm:
In arch include files:
#define pud_write pud_write
static inline int pud_write(pud_t pud)
.....
Then in include/asm-generic/pgtable.h:
#ifndef pud_write
tatic inline int pud_write(pud_t pud)
{
....
}
#endif
If you had, then the powerpc code would have worked ... ;-) and many
of the other interfaces in include/asm-generic/pgtable.h are
protected that way ...
Given that some architecture already define pmd_write() as a macro, it's
a net reduction to drop the definition of __HAVE_ARCH_PMD_WRITE.
Link: http://lkml.kernel.org/r/151129126721.37405.13339850900081557813.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Oliver OHalloran <oliveroh@au1.ibm.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After emulating instructions we may want return to user-space to handle
single-step debugging. Introduce a helper function, which, if
single-step is enabled, sets the run structure for return and returns
true.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
VTTBR_BADDR_MASK is used to sanity check the size and alignment of the
VTTBR address. It seems to currently be off by one, thereby only
allowing up to 39-bit addresses (instead of 40-bit) and also
insufficiently checking the alignment. This patch fixes it.
This patch is the 32bit pendent of Kristina's arm64 fix, and
she deserves the actual kudos for pinpointing that one.
Fixes: f7ed45be3ba52 ("KVM: ARM: World-switch implementation")
Cc: <stable@vger.kernel.org> # 3.9
Reported-by: Kristina Martsenko <kristina.martsenko@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Map the interrupt numbers for SA1111 through the SA1111 IRQ domain
rather than doing our own translation. This allows us to eliminate
the irq_base sachip member.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Use an IRQ domain for SA1111 interrupts, which allows us to separate the
hardware interrupt number from the Linux interrupt number. We can then
use the hardware interrupt number stored in the irq_data to calculate
the register offsets and mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
SA1111_VBASE, SA1111_p2v, SA1111_v2p, _SA1111, SA1111_ADDR_WIDTH,
SA1111_ADDR_MASK, and SA1111_DMA_ADDR are not used anywhere in the
kernel, so remove these redundant definitions.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Remove the special sa1111 mmio accessors from core sa1111 code, and
their definition in sa1111.h now that all users are gone.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
The legacy device-driver suspend/resume methods are not used by any of
our drivers, so let's remove this redundant code.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings.
With this change in place we can keep device-specific configuration in
the driver and the driver can be able to support CMT1 specific features.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings.
With this change in place we can keep device-specific configuration in
the driver and the driver can be able to support CMT1 specific features.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings.
With this change in place we can keep device-specific configuration in
the driver and the driver can be able to support CMT1 specific features.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings.
With this change in place we can keep device-specific configuration in
the driver and the driver can be able to support CMT1 specific features.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Use the recently updated r8a73a4 CMT1 compat string.
With this change in place we can keep device-specific configuration in
the driver and the driver can be able to support CMT1 specific features.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add the device tree node for the Advanced Power Management Unit (APMU).
Use the "enable-method" prop to point out that the APMU should be used
for the SMP support.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This reverts commit 5b725054147deaf966b3919e10a86c6bfe946a18.
The rtc block on i.MX53 is a completely different hardware than the
one found on i.MX25.
Cc: <stable@vger.kernel.org> #4.14
Reported-by: Noel Vellemans <Noel.Vellemans@visionbms.com>
Suggested-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
at24mac602 should be at the I2C address 0x50, so that it matches the
'reg' property.
Fixes: d4cd158176c3 ("ARM: dts: vf610-zii-dev: Add .dts file for rev. C")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
With the introduction of sharpslpart partition parser we can now read the
offsets from NAND: we specify the list of the parsers as platform data, with
cmdlinepart and ofpart parsers first allowing to override the part. table
written in NAND. This is done here in the board file.
Emulators like qemu will need to pass the mtdparts in the cmdline.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
With the introduction of sharpslpart partition parser we can now read the
offsets from NAND: we specify the list of the parsers as platform data, with
cmdlinepart and ofpart parsers first allowing to override the part. table
written in NAND. This is done here in the board file.
Emulators like qemu will need to pass the mtdparts in the cmdline.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
With the introduction of sharpslpart partition parser we can now read the
offsets from NAND: we specify the list of the parsers as platform data, with
cmdlinepart and ofpart parsers first allowing to override the part. table
written in NAND. This is done here in the board file.
Emulators like qemu will need to pass the mtdparts in the cmdline.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
With the introduction of sharpslpart partition parser we can now read the
offsets from NAND: we specify the list of the parsers as platform data, with
cmdlinepart and ofpart parsers first allowing to override the part. table
written in NAND. This is done here in the board file.
Emulators like qemu will need to pass the mtdparts in the cmdline.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
include/linux/i2c is to be deprecated. Move this platform_data to the
proper platform_data dir.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
Platform data is not the right place for such declarations, use
devices.h in the mach-directory where the rest is located. Note that the
some board files needed an additional include for this to work.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
|
|
|
|
|
