| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In suspend/resume procedure for AT91 architecture different controllers
(PMC, SHDWC, RAM, RAM PHY, SFRBU) are accessed to do the proper settings
for power saving. Commit f0bbf17958e8 ("ARM: at91: pm: add self-refresh
support for sama7g5") introduced the access to RAMC PHY controller for
SAMA7G5. The access to this controller is done after RAMC ports are
closed, thus any TLB walk necessary for RAMC PHY virtual address will
fail. In the development branch this was not encountered. However, on
current kernel the issue is reproducible.
To solve the issue the previous mechanism of pre-loading the TLB with
the RAMC PHY virtual address has been used. However, only the addition
of this new pre-load breaks the functionality for ARMv5 based
devices (SAM9X60). This behavior has been encountered previously
while debugging this code and using the same mechanism for pre-loading
address for different controllers (e.g. pin controller, the assumption
being that other requested translations are replaced from TLB).
To solve this new issue the TLB flush + the extension of pre-loading
the rest of controllers to TLB (e.g. PMC, RAMC) has been added. The
rest of the controllers should have been pre-loaded previously, anyway.
Fixes: f0bbf17958e8 ("ARM: at91: pm: add self-refresh support for sama7g5")
Depends-on: e42cbbe5c9a2 ("ARM: at91: pm: group constants and addresses loading")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-4-claudiu.beznea@microchip.com
|
|
Group constants and addresses loading. This commit prepares the field for
the next one.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-3-claudiu.beznea@microchip.com
|
|
SAMA7G5-EK board has DDR3L type of memory soldered. This needs 1.35V. The
1.35V for DDR3L rail at run-time is selected by the proper configuration
on SELV2 pin (for 1.35V it needs to be in high-z state). When suspended
the MCP16502 PMIC soldered on SAMA7G5-EK will use different sets of
configuration registers to provide proper voltages on its rail. Run-time
configuration registers could be configured differently than suspend
configuration register for MCP16502 (VSEL2 affects only run-time
configuration). In suspend states the DDR3L memory soldered on SAMA7G5-EK
switches to self-refresh. Even on self-refresh it needs to be powered by
a 1.35V rail. Thus, make sure the PMIC is configured properly when system
is suspended.
Fixes: 7540629e2fc7 (ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-2-claudiu.beznea@microchip.com
|
|
Before commit 0e30f47232ab5 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.
Though the spi-nor device on imx6sx-sdb/imx6ul(l/z)-14x14-evk board
do not support PP-1-4-4/PP-1-1-4, but if tx is 4 in dts file, it will also
impact the read mode selection. For the spi-nor device on the upper mentioned
boards, they support read 1-4-4 mode and read 1-1-4 mode according to the
device internal sfdp register. But qspi host controller do not support
read 1-4-4 mode. so need to set the tx to 1, let the common code finally
select read 1-1-4 mode, PP-1-1-1 mode.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Fixes: 0e30f47232ab ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On ARM CPUs that lack div/mod instructions, ALU32 BPF_DIV and BPF_MOD are
implemented using a call to a helper function. Before, the emitted code
for those function calls failed to preserve caller-saved ARM registers.
Since some of those registers happen to be mapped to BPF registers, it
resulted in eBPF register values being overwritten.
This patch emits code to push and pop the remaining caller-saved ARM
registers r2-r3 into the stack during the div/mod function call. ARM
registers r0-r1 are used as arguments and return value, and those were
already saved and restored correctly.
Fixes: 39c13c204bb1 ("arm: eBPF JIT compiler")
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Commit 078fb7aa6a83 ("arm: dts: vexpress: Fix addressing issues with
'motherboard-bus' nodes") broke booting on a couple of 32-bit VExpress
boards. The problem is #address-cells size changed, but interrupt-map
was not updated. This results in the timer interrupt (and all the
other motherboard interrupts) not getting mapped.
As the 'interrupt-map' properties are all just duplicates across boards,
just move them into vexpress-v2m.dtsi and vexpress-v2m-rs1.dtsi.
Strictly speaking, 'interrupt-map' is dependent on the parent
interrupt controller, but it's not likely we'll ever have a different
parent than GICv2 on these old platforms. If there was one,
'interrupt-map' can still be overridden.
Link: https://lore.kernel.org/r/20210924214221.1877686-1-robh@kernel.org
Fixes: 078fb7aa6a83 ("arm: dts: vexpress: Fix addressing issues with 'motherboard-bus' nodes")
Cc: Guillaume Tucker <guillaume.tucker@collabora.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Reported-by: Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay
config") sets the RX/TX delay according to the phy-mode property in the
device tree. For the A20-olinuxino-lime2 board this is "rgmii", which is the
wrong setting.
Following the example of a900cac3750b ("ARM: dts: sun7i: a20: bananapro:
Fix ethernet phy-mode") the phy-mode is changed to "rgmii-id" which gets
the Ethernet working again on this board.
Signed-off-by: Bastien Roucariès <rouca@debian.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210916081721.237137-1-rouca@debian.org
|
|
Invoke rseq_handle_notify_resume() from tracehook_notify_resume() now
that the two function are always called back-to-back by architectures
that have rseq. The rseq helper is stubbed out for architectures that
don't support rseq, i.e. this is a nop across the board.
Note, tracehook_notify_resume() is horribly named and arguably does not
belong in tracehook.h as literally every line of code in it has nothing
to do with tracing. But, that's been true since commit a42c6ded827d
("move key_repace_session_keyring() into tracehook_notify_resume()")
first usurped tracehook_notify_resume() back in 2012. Punt cleaning that
mess up to future patches.
No functional change intended.
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210901203030.1292304-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Enable CONFIG_FB which is nowadays required for CONFIG_DRM_PANEL_LVDS,
CONFIG_DRM_PANEL_SIMPLE, CONFIG_DRM_PANEL_SEIKO_43WVF1G,
CONFIG_FB_MODE_HELPERS, CONFIG_BACKLIGHT_PWM, CONFIG_BACKLIGHT_GPIO,
CONFIG_FRAMEBUFFER_CONSOLE, CONFIG_LOGO, CONFIG_FONTS, CONFIG_FONT_8x8
and CONFIG_FONT_8x16.
Fixes: f611b1e7624c ("drm: Avoid circular dependencies for CONFIG_FB")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently, it is no longer possible to retrieve a DHCP address
on the imx6qdl-pico board.
This issue has been exposed by commit f5d9aa79dfdf ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").
Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.
Fixes: 98670a0bb0ef14bbb3 ("ARM: dts: imx6qdl: Add imx6qdl-pico support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The MIC2025 switch input signal nEN is active low, describe it as such
in the DT. The previous change to this regulator polarity was incorrectly
influenced by broken quirks in gpiolib-of.c, which is now long fixed. So
fix this regulator polarity setting here once and for all.
Fixes: 3c3601cd6a6d3 ("ARM: dts: imx53: Update USB configuration on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The panel already contains pinctrl-0 phandle, but it is missing
the default pinctrl-names property, so the pin configuration is
ignored. Fill in the missing pinctrl-names property, so the pin
configuration is applied.
Fixes: d81765d693db6 ("ARM: dts: imx53: Update LCD panel node on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This reverts commit cc8870bf4c3ab0af385538460500a9d342ed945f.
Since commit cc8870bf4c3a ("ARM: imx6q: drop of_platform_default_populate()
from init_machine") the following errors are seen on boot:
[ 0.123372] imx6q_suspend_init: failed to find ocram device!
[ 0.123537] imx6_pm_common_init: No DDR LPM support with suspend -19!
, which break suspend/resume on imx6q/dl.
Revert the offeding commit to avoid the regression.
Thanks to Tim Harvey for bisecting this problem.
Cc: stable@vger.kernel.org
Fixes: cc8870bf4c3a ("ARM: imx6q: drop of_platform_default_populate() from init_machine")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since the LED multicolor framework support was added in commit
92a81562e695 ("leds: lp55xx: Add multicolor framework support to lp55xx")
LEDs on this platform stopped working.
Author of the framework attempted to accommodate this DT to the
framework in commit b86d3d21cd4c ("ARM: dts: imx6dl-yapp4: Add reg property
to the lp5562 channel node") but that is not sufficient. A color property
is now required even if the multicolor framework is not used, otherwise
the driver probe fails:
lp5562: probe of 1-0030 failed with error -22
Add the color property to fix this.
Fixes: 92a81562e695 ("leds: lp55xx: Add multicolor framework support to lp55xx")
Cc: <stable@vger.kernel.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The legacy clock names (including the _clk suffix) was dropped from the
driver, so update the dts accordingly).
Tested on Nexus 7 2013, no functional changes.
Signed-off-by: David Heidelberg <david@ixit.cz>
[bjorn: Updated commit message]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210829133918.57780-2-david@ixit.cz
|
|
The 'motherboard-bus' node in Arm Ltd boards fails schema checks as
'simple-bus' child nodes must have a unit-address. The 'ranges' handling is
also wrong (or at least strange) as the mapping of SMC chip selects should
be in the 'arm,vexpress,v2m-p1' node rather than a generic 'simple-bus'
node. Either there's 1 too many levels of 'simple-bus' nodes or 'ranges'
should be moved down a level. The latter change is more simple, so let's do
that. As the 'ranges' value doesn't vary for a given motherboard instance,
we can move 'ranges' into the motherboard dtsi files.
Link: https://lore.kernel.org/r/20210819184239.1192395-6-robh@kernel.org
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes
AT91 fixes #1 for 5.15:
- Fixes for newly introduced SAMA7G5 and its Power Management code.
Associated core peripherals need to be instantiated in DT for
benefiting from best PM support like Backup mode with DDR in
Self-Refresh.
- Add chip ID for SAMA7G5 for easing the kernel log identification.
- Avoid Camera Sensor probe error on sama5d27 som1 ek board.
* tag 'at91-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d2_som1_ek: disable ISC node by default
ARM: at91: pm: switch backup area to vbat in backup mode
ARM: dts: at91: sama7g5: add chipid
ARM: dts: at91: sama7g5: add shdwc node
ARM: dts: at91: sama7g5: add securam node
ARM: dts: at91: sama7g5: add ram controllers
ARM: at91: pm: do not panic if ram controllers are not enabled
Link: https://lore.kernel.org/r/20210914162314.54347-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Without a sensor node, the ISC will simply fail to probe, as the
corresponding port node is missing.
It is then logical to disable the node in the devicetree.
If we add a port with a connection to a sensor endpoint, ISC can be enabled.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210902121358.503589-1-eugen.hristev@microchip.com
|
|
Backup area is now switched to VDDIN33 at boot (with the help of
bootloader). When switching to backup mode we need to switch backup area
to VBAT as all the other power sources are cut off. The resuming from
backup mode is done with the help of bootloader, so there is no need to
do something particular in Linux to restore backup area power source.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210830100927.22711-1-claudiu.beznea@microchip.com
|
|
Add chipid node for sama7g5.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210908094329.182477-1-claudiu.beznea@microchip.com
|
|
Add shutdown controller node and enable it.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210823131915.23857-5-claudiu.beznea@microchip.com
|
|
Add securam node.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210823131915.23857-4-claudiu.beznea@microchip.com
|
|
Add RAM and RAMC PHY controllers. These are necessary for platform
specific power management code.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210823131915.23857-3-claudiu.beznea@microchip.com
|
|
In case PM is enabled but there is no RAM controller information
in DT the code will panic. Avoid such scenarios by not initializing
platform specific PM code in case RAM controller is not provided
via DT.
Reported-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: 827de1f123ba0 ("ARM: at91: remove at91_dt_initialize and machine init_early()")
Fixes: 892e1f4a3ae58 ("ARM: at91: pm: add sama7g5 ddr phy controller")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210823131915.23857-2-claudiu.beznea@microchip.com
|
|
DRM_FBDEV_EMULATION previously selected FB and was default y as long as DRM
was enabled. In commit f611b1e7624c ("drm: Avoid circular dependencies for
CONFIG_FB") the select was replaced with a depends on FB, disabling the
drivers that depended on it.
Renable FB so we get back FB_EFI, FB_WM8505, FB_SH_MOBILE_LCDC, FB_SIMPLE and
VIDEO_VIVID.
It must be set to y and not a module as the test driver VIDEO_VIVID
requires it to be built in.
Link: https://lore.kernel.org/r/CAK8P3a18EdBKQdGDOZc9cPKsf=hY8==v2cO0DBE_tyd82Uq-Ng@mail.gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Some drivers have not been built as they gained dependencies in kconfig but those
dependencies were not added to the defconfig.
The MSM pinctrl drivers fell out of the defconfig as of commit be117ca32261
("pinctrl: qcom: Kconfig: Rework PINCTRL_MSM to be a depenency rather then a
selected config"). Add PINCTRL_MSM so these stay enabled.
EDAC depends on RAS, so enable it to ensure the EDAC drivers stay
enabled.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Based on 'ranges', the 'bus@4000000' node unit-address is off by 1 '0'.
Link: https://lore.kernel.org/r/20210819184239.1192395-5-robh@kernel.org
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Drop the '#interrupt-cells' property in the motherboard node which has no
effect as the node is neither an interrupt-controller or interrupt-map
(that's in the parent node).
Drop 'model' as it is not used by software nor documented.
Drop 'arm,v2m-memory-map' as it is not used by software. The purpose was
to describe which memory map, but that's all described by the DT
already.
Link: https://lore.kernel.org/r/20210819184239.1192395-4-robh@kernel.org
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Align the watchdog and mmc device node names with the schema to fix
warnings like:
mmci@50000: $nodename:0: 'mmci@50000' does not match '^mmc(@.*)?$'
wdt@f0000: $nodename:0: 'wdt@f0000' does not match '^watchdog(@.*|-[0-9a-f])?$'
Link: https://lore.kernel.org/r/20210820081733.83976-2-krzysztof.kozlowski@canonical.com
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The 28NM DSI PLL driver for msm8960 calculates with a 27MHz reference
clock and should hence use PXO, not CXO which runs at 19.2MHz.
Note that none of the DSI PHY/PLL drivers currently use this "ref"
clock; they all rely on (sometimes inexistant) global clock names and
usually function normally without a parent clock. This discrepancy will
be corrected in a future patch, for which this change needs to be in
place first.
Fixes: 6969d1d9c615 ("ARM: dts: qcom-apq8064: Set 'cxo_board' as ref clock of the DSI PHY")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20210829203027.276143-2-marijn.suijten@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Also resolves these kernel warnings for APQ8064:
adreno 4300000.adreno-3xx: Using legacy qcom,chipid binding!
adreno 4300000.adreno-3xx: Use compatible qcom,adreno-320.2 instead.
Tested on Nexus 7 2013, no functional changes.
Cc: <stable@vger.kernel.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210818065317.19822-1-david@ixit.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Pull ARM development updates from Russell King:
- Rename "mod_init" and "mod_exit" so that initcall debug output is
actually useful (Randy Dunlap)
- Update maintainers entries for linux-arm-kernel to indicate it is
moderated for non-subscribers (Randy Dunlap)
- Move install rules to arch/arm/Makefile (Masahiro Yamada)
- Drop unnecessary ARCH_NR_GPIOS definition (Linus Walleij)
- Don't warn about atags_to_fdt() stack size (David Heidelberg)
- Speed up unaligned copy_{from,to}_kernel_nofault (Arnd Bergmann)
- Get rid of set_fs() usage (Arnd Bergmann)
- Remove checks for GCC prior to v4.6 (Geert Uytterhoeven)
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9118/1: div64: Remove always-true __div64_const32_is_OK() duplicate
ARM: 9117/1: asm-generic: div64: Remove always-true __div64_const32_is_OK()
ARM: 9116/1: unified: Remove check for gcc < 4
ARM: 9110/1: oabi-compat: fix oabi epoll sparse warning
ARM: 9113/1: uaccess: remove set_fs() implementation
ARM: 9112/1: uaccess: add __{get,put}_kernel_nofault
ARM: 9111/1: oabi-compat: rework fcntl64() emulation
ARM: 9114/1: oabi-compat: rework sys_semtimedop emulation
ARM: 9108/1: oabi-compat: rework epoll_wait/epoll_pwait emulation
ARM: 9107/1: syscall: always store thread_info->abi_syscall
ARM: 9109/1: oabi-compat: add epoll_pwait handler
ARM: 9106/1: traps: use get_kernel_nofault instead of set_fs()
ARM: 9115/1: mm/maccess: fix unaligned copy_{from,to}_kernel_nofault
ARM: 9105/1: atags_to_fdt: don't warn about stack size
ARM: 9103/1: Drop ARCH_NR_GPIOS definition
ARM: 9102/1: move theinstall rules to arch/arm/Makefile
ARM: 9100/1: MAINTAINERS: mark all linux-arm-kernel@infradead list as moderated
ARM: 9099/1: crypto: rename 'mod_init' & 'mod_exit' functions to be module-specific
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are mostly ARM cpufreq driver updates, including one new
MediaTek driver that has just passed all of the reviews, with the
addition of a revert of a recent intel_pstate commit, some core
cpufreq changes and a DT-related update of the operating performance
points (OPP) support code.
Specifics:
- Add new cpufreq driver for the MediaTek MT6779 platform called
mediatek-hw along with corresponding DT bindings (Hector.Yuan).
- Add DCVS interrupt support to the qcom-cpufreq-hw driver (Thara
Gopinath).
- Make the qcom-cpufreq-hw driver set the dvfs_possible_from_any_cpu
policy flag (Taniya Das).
- Blocklist more Qualcomm platforms in cpufreq-dt-platdev (Bjorn
Andersson).
- Make the vexpress cpufreq driver set the CPUFREQ_IS_COOLING_DEV
flag (Viresh Kumar).
- Add new cpufreq driver callback to allow drivers to register with
the Energy Model in a consistent way and make several drivers use
it (Viresh Kumar).
- Change the remaining users of the .ready() cpufreq driver callback
to move the code from it elsewhere and drop it from the cpufreq
core (Viresh Kumar).
- Revert recent intel_pstate change adding HWP guaranteed performance
change notification support to it that led to problems, because the
notification in question is triggered prematurely on some systems
(Rafael Wysocki).
- Convert the OPP DT bindings to DT schema and clean them up while at
it (Rob Herring)"
* tag 'pm-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
Revert "cpufreq: intel_pstate: Process HWP Guaranteed change notification"
cpufreq: mediatek-hw: Add support for CPUFREQ HW
cpufreq: Add of_perf_domain_get_sharing_cpumask
dt-bindings: cpufreq: add bindings for MediaTek cpufreq HW
cpufreq: Remove ready() callback
cpufreq: sh: Remove sh_cpufreq_cpu_ready()
cpufreq: acpi: Remove acpi_cpufreq_cpu_ready()
cpufreq: qcom-hw: Set dvfs_possible_from_any_cpu cpufreq driver flag
cpufreq: blocklist more Qualcomm platforms in cpufreq-dt-platdev
cpufreq: qcom-cpufreq-hw: Add dcvs interrupt support
cpufreq: scmi: Use .register_em() to register with energy model
cpufreq: vexpress: Use .register_em() to register with energy model
cpufreq: scpi: Use .register_em() to register with energy model
dt-bindings: opp: Convert to DT schema
dt-bindings: Clean-up OPP binding node names in examples
ARM: dts: omap: Drop references to opp.txt
cpufreq: qcom-cpufreq-hw: Use .register_em() to register with energy model
cpufreq: omap: Use .register_em() to register with energy model
cpufreq: mediatek: Use .register_em() to register with energy model
cpufreq: imx6q: Use .register_em() to register with energy model
...
|
|
Merge more updates from Andrew Morton:
"147 patches, based on 7d2a07b769330c34b4deabeed939325c77a7ec2f.
Subsystems affected by this patch series: mm (memory-hotplug, rmap,
ioremap, highmem, cleanups, secretmem, kfence, damon, and vmscan),
alpha, percpu, procfs, misc, core-kernel, MAINTAINERS, lib,
checkpatch, epoll, init, nilfs2, coredump, fork, pids, criu, kconfig,
selftests, ipc, and scripts"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
scripts: check_extable: fix typo in user error message
mm/workingset: correct kernel-doc notations
ipc: replace costly bailout check in sysvipc_find_ipc()
selftests/memfd: remove unused variable
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
configs: remove the obsolete CONFIG_INPUT_POLLDEV
prctl: allow to setup brk for et_dyn executables
pid: cleanup the stale comment mentioning pidmap_init().
kernel/fork.c: unexport get_{mm,task}_exe_file
coredump: fix memleak in dump_vma_snapshot()
fs/coredump.c: log if a core dump is aborted due to changed file permissions
nilfs2: use refcount_dec_and_lock() to fix potential UAF
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
trap: cleanup trap_init()
init: move usermodehelper_enable() to populate_rootfs()
...
|
|
This CONFIG option was removed in commit 278b13ce3a89 ("Input: remove
input_polled_dev implementation") so there's no point to keep it in
defconfigs any longer.
Get rid of the leftover for all arches.
Link: https://lkml.kernel.org/r/20210726074741.1062-1-yuzenghui@huawei.com
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are some empty trap_init() definitions in different ARCHs, Introduce
a new weak trap_init() function to clean them up.
Link: https://lkml.kernel.org/r/20210812123602.76356-1-wangkefeng.wang@huawei.com
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> [arm32]
Acked-by: Vineet Gupta [arc]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Stafford Horne <shorne@gmail.com>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <palmerdabbelt@google.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* pm-opp:
dt-bindings: opp: Convert to DT schema
dt-bindings: Clean-up OPP binding node names in examples
ARM: dts: omap: Drop references to opp.txt
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- simplify the Kconfig use of FTRACE and TRACE_IRQFLAGS_SUPPORT
- bootconfig can now start histograms
- bootconfig supports group/all enabling
- histograms now can put values in linear size buckets
- execnames can be passed to synthetic events
- introduce "event probes" that attach to other events and can retrieve
data from pointers of fields, or record fields as different types (a
pointer to a string as a string instead of just a hex number)
- various fixes and clean ups
* tag 'trace-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (35 commits)
tracing/doc: Fix table format in histogram code
selftests/ftrace: Add selftest for testing duplicate eprobes and kprobes
selftests/ftrace: Add selftest for testing eprobe events on synthetic events
selftests/ftrace: Add test case to test adding and removing of event probe
selftests/ftrace: Fix requirement check of README file
selftests/ftrace: Add clear_dynamic_events() to test cases
tracing: Add a probe that attaches to trace events
tracing/probes: Reject events which have the same name of existing one
tracing/probes: Have process_fetch_insn() take a void * instead of pt_regs
tracing/probe: Change traceprobe_set_print_fmt() to take a type
tracing/probes: Use struct_size() instead of defining custom macros
tracing/probes: Allow for dot delimiter as well as slash for system names
tracing/probe: Have traceprobe_parse_probe_arg() take a const arg
tracing: Have dynamic events have a ref counter
tracing: Add DYNAMIC flag for dynamic events
tracing: Replace deprecated CPU-hotplug functions.
MAINTAINERS: Add an entry for os noise/latency
tracepoint: Fix kerneldoc comments
bootconfig/tracing/ktest: Update ktest example for boot-time tracing
tools/bootconfig: Use per-group/all enable option in ftrace2bconf script
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add -s option (strict mode) to merge_config.sh to make it fail when
any symbol is redefined.
- Show a warning if a different compiler is used for building external
modules.
- Infer --target from ARCH for CC=clang to let you cross-compile the
kernel without CROSS_COMPILE.
- Make the integrated assembler default (LLVM_IAS=1) for CC=clang.
- Add <linux/stdarg.h> to the kernel source instead of borrowing
<stdarg.h> from the compiler.
- Add Nick Desaulniers as a Kbuild reviewer.
- Drop stale cc-option tests.
- Fix the combination of CONFIG_TRIM_UNUSED_KSYMS and CONFIG_LTO_CLANG
to handle symbols in inline assembly.
- Show a warning if 'FORCE' is missing for if_changed rules.
- Various cleanups
* tag 'kbuild-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (39 commits)
kbuild: redo fake deps at include/ksym/*.h
kbuild: clean up objtool_args slightly
modpost: get the *.mod file path more simply
checkkconfigsymbols.py: Fix the '--ignore' option
kbuild: merge vmlinux_link() between ARCH=um and other architectures
kbuild: do not remove 'linux' link in scripts/link-vmlinux.sh
kbuild: merge vmlinux_link() between the ordinary link and Clang LTO
kbuild: remove stale *.symversions
kbuild: remove unused quiet_cmd_update_lto_symversions
gen_compile_commands: extract compiler command from a series of commands
x86: remove cc-option-yn test for -mtune=
arc: replace cc-option-yn uses with cc-option
s390: replace cc-option-yn uses with cc-option
ia64: move core-y in arch/ia64/Makefile to arch/ia64/Kbuild
sparc: move the install rule to arch/sparc/Makefile
security: remove unneeded subdir-$(CONFIG_...)
kbuild: sh: remove unused install script
kbuild: Fix 'no symbols' warning when CONFIG_TRIM_UNUSD_KSYMS=y
kbuild: Switch to 'f' variants of integrated assembler flag
kbuild: Shuffle blank line to improve comment meaning
...
|
|
Merge misc updates from Andrew Morton:
"173 patches.
Subsystems affected by this series: ia64, ocfs2, block, and mm (debug,
pagecache, gup, swap, shmem, memcg, selftests, pagemap, mremap,
bootmem, sparsemem, vmalloc, kasan, pagealloc, memory-failure,
hugetlb, userfaultfd, vmscan, compaction, mempolicy, memblock,
oom-kill, migration, ksm, percpu, vmstat, and madvise)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (173 commits)
mm/madvise: add MADV_WILLNEED to process_madvise()
mm/vmstat: remove unneeded return value
mm/vmstat: simplify the array size calculation
mm/vmstat: correct some wrong comments
mm/percpu,c: remove obsolete comments of pcpu_chunk_populated()
selftests: vm: add COW time test for KSM pages
selftests: vm: add KSM merging time test
mm: KSM: fix data type
selftests: vm: add KSM merging across nodes test
selftests: vm: add KSM zero page merging test
selftests: vm: add KSM unmerge test
selftests: vm: add KSM merge test
mm/migrate: correct kernel-doc notation
mm: wire up syscall process_mrelease
mm: introduce process_mrelease system call
memblock: make memblock_find_in_range method private
mm/mempolicy.c: use in_task() in mempolicy_slab_node()
mm/mempolicy: unify the create() func for bind/interleave/prefer-many policies
mm/mempolicy: advertise new MPOL_PREFERRED_MANY
mm/hugetlb: add support for mempolicy MPOL_PREFERRED_MANY
...
|
|
Split off from prev patch in the series that implements the syscall.
Link: https://lkml.kernel.org/r/20210809185259.405936-2-surenb@google.com
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: Jan Engelhardt <jengelh@inai.de>
Cc: Jann Horn <jannh@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Tim Murray <timmurray@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are a lot of uses of memblock_find_in_range() along with
memblock_reserve() from the times memblock allocation APIs did not exist.
memblock_find_in_range() is the very core of memblock allocations, so any
future changes to its internal behaviour would mandate updates of all the
users outside memblock.
Replace the calls to memblock_find_in_range() with an equivalent calls to
memblock_phys_alloc() and memblock_phys_alloc_range() and make
memblock_find_in_range() private method of memblock.
This simplifies the callers, ensures that (unlikely) errors in
memblock_reserve() are handled and improves maintainability of
memblock_find_in_range().
Link: https://lkml.kernel.org/r/20210816122622.30279-1-rppt@kernel.org
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Acked-by: Kirill A. Shutemov <kirill.shtuemov@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> [ACPI]
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Nick Kossifidis <mick@ics.forth.gr> [riscv]
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
flush_kernel_dcache_page is a rather confusing interface that implements a
subset of flush_dcache_page by not being able to properly handle page
cache mapped pages.
The only callers left are in the exec code as all other previous callers
were incorrect as they could have dealt with page cache pages. Replace
the calls to flush_kernel_dcache_page with calls to flush_dcache_page,
which for all architectures does either exactly the same thing, can
contains one or more of the following:
1) an optimization to defer the cache flush for page cache pages not
mapped into userspace
2) additional flushing for mapped page cache pages if cache aliases
are possible
Link: https://lkml.kernel.org/r/20210712060928.4161649-7-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Cc: Alex Shi <alexs@kernel.org>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.15 kernel cycle, no
core changes at all this time, just driver work!
New drivers:
- New subdriver for Intel Keem Bay (an ARM-based SoC)
- New subdriver for Qualcomm MDM9607 and SM6115
- New subdriver for ST Microelectronics STM32MP135
- New subdriver for Freescale i.MX8ULP ("Ultra Low Power")
- New subdriver for Ingenic X2100
- Support for Qualcomm PMC8180, PMC8180C, SA8155p-adp PMIC GPIO
- Support Samsung Exynos850
- Support Renesas RZ/G2L
Enhancements:
- A major refactoring of the Rockchip driver, breaking part of it out
to a separate GPIO driver in drivers/gpio
- Pin bias support on Renesas r8a77995
- Add SCI pins support to Ingenic JZ4755 and JZ4760
- Mediatek device tree bindings converted to YAML"
* tag 'pinctrl-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (53 commits)
pinctrl: renesas: Add RZ/G2L pin and gpio controller driver
pinctrl: samsung: Add Exynos850 SoC specific data
dt-bindings: pinctrl: samsung: Add Exynos850 doc
MAINTAINERS: Add maintainers for amd-pinctrl driver
pinctrl: Add Intel Keem Bay pinctrl driver
dt-bindings: pinctrl: Add bindings for Intel Keembay pinctrl driver
pinctrl: zynqmp: Drop pinctrl_unregister for devm_ registered device
dt-bindings: pinctrl: qcom-pmic-gpio: Remove the interrupts property
dt-bindings: pinctrl: qcom-pmic-gpio: Convert qcom pmic gpio bindings to YAML
dt-bindings: pinctrl: mt8195: Use real world values for drive-strength arguments
dt-bindings: mediatek: convert pinctrl to yaml
arm: dts: mt8183: Move pinfunc to include/dt-bindings/pinctrl
arm: dts: mt8135: Move pinfunc to include/dt-bindings/pinctrl
pinctrl: ingenic: Add .max_register in regmap_config
pinctrl: ingenic: Fix bias config for X2000(E)
pinctrl: ingenic: Fix incorrect pull up/down info
pinctrl: Ingenic: Add pinctrl driver for X2100.
dt-bindings: pinctrl: Add bindings for Ingenic X2100.
pinctrl: Ingenic: Add SSI pins support for JZ4755 and JZ4760.
pinctrl: Ingenic: Improve the code.
...
|
|
Pull dma-mapping updates from Christoph Hellwig:
- fix debugfs initialization order (Anthony Iliopoulos)
- use memory_intersects() directly (Kefeng Wang)
- allow to return specific errors from ->map_sg (Logan Gunthorpe,
Martin Oliveira)
- turn the dma_map_sg return value into an unsigned int (me)
- provide a common global coherent pool іmplementation (me)
* tag 'dma-mapping-5.15' of git://git.infradead.org/users/hch/dma-mapping: (31 commits)
hexagon: use the generic global coherent pool
dma-mapping: make the global coherent pool conditional
dma-mapping: add a dma_init_global_coherent helper
dma-mapping: simplify dma_init_coherent_memory
dma-mapping: allow using the global coherent pool for !ARM
ARM/nommu: use the generic dma-direct code for non-coherent devices
dma-direct: add support for dma_coherent_default_memory
dma-mapping: return an unsigned int from dma_map_sg{,_attrs}
dma-mapping: disallow .map_sg operations from returning zero on error
dma-mapping: return error code from dma_dummy_map_sg()
x86/amd_gart: don't set failed sg dma_address to DMA_MAPPING_ERROR
x86/amd_gart: return error code from gart_map_sg()
xen: swiotlb: return error code from xen_swiotlb_map_sg()
parisc: return error code from .map_sg() ops
sparc/iommu: don't set failed sg dma_address to DMA_MAPPING_ERROR
sparc/iommu: return error codes from .map_sg() ops
s390/pci: don't set failed sg dma_address to DMA_MAPPING_ERROR
s390/pci: return error code from s390_dma_map_sg()
powerpc/iommu: don't set failed sg dma_address to DMA_MAPPING_ERROR
powerpc/iommu: return error code from .map_sg() ops
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Optionally, provide an index of possible printk messages via
<debugfs>/printk/index/. It can be used when monitoring important
kernel messages on a farm of various hosts. The monitor has to be
updated when some messages has changed or are not longer available by
a newly deployed kernel.
- Add printk.console_no_auto_verbose boot parameter. It allows to
generate crash dump even with slow consoles in a reasonable time
frame.
- Remove printk_safe buffers. The messages are always stored directly
to the main logbuffer, even in NMI or recursive context. Also it
allows to serialize syslog operations by a mutex instead of a spin
lock.
- Misc clean up and build fixes.
* tag 'printk-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk/index: Fix -Wunused-function warning
lib/nmi_backtrace: Serialize even messages about idle CPUs
printk: Add printk.console_no_auto_verbose boot parameter
printk: Remove console_silent()
lib/test_scanf: Handle n_bits == 0 in random tests
printk: syslog: close window between wait and read
printk: convert @syslog_lock to mutex
printk: remove NMI tracking
printk: remove safe buffers
printk: track/limit recursion
lib/nmi_backtrace: explicitly serialize banner and regs
printk: Move the printk() kerneldoc comment to its new home
printk/index: Fix warning about missing prototypes
MIPS/asm/printk: Fix build failure caused by printk
printk: index: Add indexing support to dev_printk
printk: Userspace format indexing support
printk: Rework parse_prefix into printk_parse_prefix
printk: Straighten out log_flags into printk_info_flags
string_helpers: Escape double quotes in escape_special
printk/console: Check consistent sequence number when handling race in console_unlock()
|
|
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, the bulk of work in the SoC tree goes into DT files, this
time with a roughly even split between 32-bit and 64-bit SoCs rather
than the usual mostly 64-bit changes.
New SoCs:
- Microchip SAMA7 SoC family based on Cortex-A7, a new 32-bit
platform based on the older SAMA5 series.
- Qualcomm Snapdragon SDM636 and SM8150, variations of the existing
phone SoCs.
- Renesas R-Car H3e-2G and M3e-2G SoCs, variations of older Renesas
SoCs.
New boards:
- Marvell CN913x reference boards
- ASpeed AST2600 BMC implementations for Facebook Cloudripper, Elbert
and Fuji server boards.
- Snapdragon 665 based Sony Xperia 10II
- Snapdragon MSM8916 based Xiaomi Redmi 2
- Snapdragon MSM8226 based Samsung Galaxy S3 Neo
- NXP i.MX based 32-bit boards:
- DHCOM based PicoITX
- DHSOM based DRC0ỉ
- SolidRun SolidSense
- SKOV i.MX6 boards.
- NXP i.MX based 64-bit boards:
- Nitrogen8 SoM and MNT Reform2
- LS1088A based Traverse Ten64
- i.MX8M based GW7902.
- NVIDIA Jetson TX2 NX Developer Kit
- 4KOpen STiH418-b2264 development board
- ux500 based Samsung phones: Gavini, Codina and Kyle
- TI AM335x based Sancloud BBE Lite
- ixp4xx dts files to replace all old board files
Other changes:
- Treewide fixes for dtc warnings
- Rockchips i/o domain support
- TI OMAP/AM3 CPSW switch driver support
- Improved device support for allwinner, aspeed, qualcomm, NXP,
nvidia, Renesas, Samsung, Amlogic, Mediatek, ixp4xx, stm32, sti,
OMAP and actions"
* tag 'dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (412 commits)
arm/arm64: dts: Fix remaining dtc 'unit_address_format' warnings
ARM: dts: rockchip: Add SFC to RV1108
arm64: dts: marvell: armada-37xx: Extend PCIe MEM space
ARM: dts: aspeed: p10bmc: Add power control pins
ARM: dts: aspeed: cloudripper: Add comments for "mdio1"
ARM: dts: aspeed: minipack: Update flash partition table
dt-bindings: arm: fsl: Add Traverse Ten64 (LS1088A) board
dt-bindings: vendor-prefixes: add Traverse Technologies
arm64: dts: add device tree for Traverse Ten64 (LS1088A)
arm64: dts: ls1088a: add missing PMU node
arm64: dts: ls1088a: add internal PCS for DPMAC1 node
ARM: dts: imx6qp-prtwd3: configure ENET_REF clock to 125MHz
ARM: dts: vf610-zii-dev-rev-b: Remove #address-cells and #size-cells property from at93c46d dt node
ARM: dts: add SKOV imx6q and imx6dl based boards
dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards
dt-bindings: vendor-prefixes: Add an entry for SKOV A/S
arm64: dts: imx8mq-reform2: add sound support
arm64: dts: imx8m: drop interrupt-affinity for pmu
arm64: dts: imx8qxp: update pmu compatible
arm64: dts: imx8mm: update pmu compatible
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM defconfig updates from Arnd Bergmann:
"The usual set of defconfig updates, including one new defconfig file
for the new sama7 family of SoCs"
* tag 'defconfig-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: config: aspeed: Regenerate defconfigs
ARM: config: aspeed_g4: Enable EDAC and SPGIO
ARM: config: aspeed: Enable KCS adapter for raw SerIO
ARM: config: aspeed: Enable hardened allocator feature
ARM: imx_v6_v7_defconfig: enable driver of the LTC3676 PMIC
ARM: multi_v7_defconfig: Enable CONFIG_TEGRA30_TSENSOR
ARM: multi_v7_defconfig: Enable Acer A500 drivers
ARM: tegra: Rebuild default configuration
ARM: tegra: Enable CONFIG_CROS_EC
ARM: tegra: Enable Acer A500 drivers
ARM: tegra: Enable CONFIG_FB
ARM: tegra: Enable CONFIG_TEGRA30_TSENSOR
ARM: configs: multi_v7: enable PL35x NAND controller
arm64: defconfig: Enable Qualcomm MSM8996 CPU clock driver
ARM: imx_v6_v7_defconfig: Let CONFIG_SCSI_LOWLEVEL be selected
ARM: imx_v6_v7_defconfig: Select CONFIG_KPROBES
ARM: multi_v7_defconfig: Enable CONFIG_MMC_MESON_MX_SDHC
ARM: multi_v7_defconfig: add sama7g5 SoC
ARM: configs: at91: add defconfig for sama7 family of SoCs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform support
and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas"
* tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
reset: simple: remove ZTE details in Kconfig help
soc: rockchip: io-domain: Remove unneeded semicolon
soc: rockchip: io-domain: add rk3568 support
dt-bindings: power: add rk3568-pmu-io-domain support
bus: ixp4xx: return on error in ixp4xx_exp_probe()
soc: renesas: Prefer memcpy() over strcpy()
firmware: tegra: Stop using seq_get_buf()
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
dt-bindings: soc: ti: pruss: Add dma-coherent property
soc: ti: Remove pm_runtime_irq_safe() usage for smartreflex
soc: ti: pruss: Enable support for ICSSG subsystems on K3 AM64x SoCs
dt-bindings: soc: ti: pruss: Update bindings for K3 AM64x SoCs
firmware: arm_scmi: Use WARN_ON() to check configured transports
firmware: arm_scmi: Fix boolconv.cocci warnings
soc: mediatek: mmsys: Fix missing UFOE component in mt8173 table routing
soc: mediatek: mmsys: add MT8365 support
...
|
|
Pull ARM SoC updates from Arnd Bergmann:
"There are three noteworthy updates for 32-bit arm platforms this time:
- The Microchip SAMA7 family based on Cortex-A7 gets introduced, a
new cousin to the older SAM9 (ARM9xx based) and SAMA5 (Cortex-A5
based) SoCs.
- The ixp4xx platform (based on Intel XScale) is finally converted to
device tree, and all the old board files are getting removed now.
- The Cirrus Logic EP93xx platform loses support for the old
MaverickCrunch FPU. Support for compiling user space applications
was already removed in gcc-4.9, and the kernel support for old
applications could not be built with clang ias. After confirming
that there are no remaining users, removing this from the kernel
seemed better than adding support for unused features to clang.
There are minor updates to the aspeed, omap and samsung platforms"
* tag 'soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
soc: aspeed-lpc-ctrl: Fix clock cleanup in error path
ARM: s3c: delete unneed local variable "delay"
soc: aspeed: Re-enable FWH2AHB on AST2600
soc: aspeed: socinfo: Add AST2625 variant
soc: aspeed: p2a-ctrl: Fix boundary check for mmap
soc: aspeed: lpc-ctrl: Fix boundary check for mmap
ARM: ixp4xx: Delete the Freecom FSG-3 boardfiles
ARM: ixp4xx: Delete GTWX5715 board files
ARM: ixp4xx: Delete Coyote and IXDPG425 boardfiles
ARM: ixp4xx: Delete Intel reference design boardfiles
ARM: ixp4xx: Delete Avila boardfiles
ARM: ixp4xx: Delete the Arcom Vulcan boardfiles
ARM: ixp4xx: Delete Gateway WG302v2 boardfiles
ARM: ixp4xx: Delete Omicron boardfiles
ARM: ixp4xx: Delete the D-Link DSM-G600 boardfiles
ARM: ixp4xx: Delete NAS100D boardfiles
ARM: ixp4xx: Delete NSLU2 boardfiles
arm: omap2: Drop the unused OMAP_PACKAGE_* KConfig entries
arm: omap2: Drop obsolete MACH_OMAP3_PANDORA entry
ARM: ep93xx: remove MaverickCrunch support
...
|
