summaryrefslogtreecommitdiff
path: root/arch/arm64
AgeCommit message (Collapse)AuthorFilesLines
2025-04-27arm64: dts: allwinner: a523: add Avaota-A1 router supportAndre Przywara2-0/+309
The Avaota A1 router board is an Open Source hardware board, designed by YuzukiHD. Pine64 produces some boards and sells them. It uses the Allwinner A527 or T527 SoC, and comes with the following features: - Eight ARM Cortex-A55 cores, Mali-G57 MC1 GPU - 1GiB/2GiB/4GiB LPDDR4 DRAM - AXP717 + AXP323 PMIC - Raspberry-Pi-2 compatible GPIO header - 1 USB 2.0 type A host port, 1 USB 3.0 type A host post - 1 USB 2.0 type C port (OTG + serial debug) - MicroSD slot - eMMC between 16 and 128 GiB - on-board 16MiB bootable SPI NOR flash - two 1Gbps Ethernet ports (via RTL8211F PHYs) - HDMI port - DP port - camera and LCD connectors - 3.5mm headphone jack - (yet) unsupported WiFi/BT chip - 1.3" LC display, connected via SPI - 12 V barrel plug for power supply Add the devicetree file describing the currently supported features. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://patch.msgid.link/20250307005712.16828-12-andre.przywara@arm.com [wens@csie.org: Squash in SD card detect pull resistor fix] Link: https://patch.msgid.link/20250425003422.3465-1-andre.przywara@arm.com Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2025-04-27arm64: dts: rockchip: Assign RT5616 MCLK rate on rk3588-friendlyelec-cm3588Tom Vincent1-0/+4
The Realtek RT5616 audio codec on the FriendlyElec CM3588 module fails to probe correctly due to the missing clock properties. This results in distorted analogue audio output. Assign MCLK to 12.288 MHz, which allows the codec to advertise most of the standard sample rates per other RK3588 devices. Fixes: e23819cf273c ("arm64: dts: rockchip: Add FriendlyElec CM3588 NAS board") Signed-off-by: Tom Vincent <linux@tlvince.com> Link: https://lore.kernel.org/r/20250417081753.644950-1-linux@tlvince.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2025-04-27arm64: dts: rockchip: Align wifi node name with bindings in CB2Krzysztof Kozlowski1-1/+1
Since commit 3c3606793f7e ("dt-bindings: wireless: bcm4329-fmac: Use wireless-controller.yaml schema"), bindings expect 'wifi' as node name: rk3566-bigtreetech-cb2-manta.dtb: sdio-wifi@1: $nodename:0: 'sdio-wifi@1' does not match '^wifi(@.*)?$' Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20250424084729.105182-1-krzysztof.kozlowski@linaro.org Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2025-04-26arm64: dts: rockchip: add dsi controller nodes on rk3588Heiko Stuebner1-0/+57
The RK3588 comes with two DSI2 controllers based on a new Synopsis IP. Add the necessary nodes for them. Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> # RK3588 EVB1 Link: https://lore.kernel.org/r/20250226140942.3825223-3-heiko@sntech.de Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2025-04-26arm64: dts: rockchip: add mipi dcphy nodes to rk3588Heiko Stuebner1-0/+42
Add the two MIPI-DC-phy nodes to the RK3588, that will be used by the DSI2 controllers and hopefully in some future also for camera input. Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> # RK3588 EVB1 Link: https://lore.kernel.org/r/20250226140942.3825223-2-heiko@sntech.de Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2025-04-26crypto: arm64/sha1 - Set finalize for short finupHerbert Xu1-1/+3
Always set sctx->finalize before calling finup as it may not have been set previously on a short final. Reported-by: Corentin LABBE <clabbe.montjoie@gmail.com> Fixes: b97d31100e36 ("crypto: arm64/sha1 - Use API partial block handling") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Tested-by: Corentin LABBE <clabbe.montjoie@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2025-04-25arm64: dts: ti: k3-am625-sk: Enable PWMJudith Mendez1-0/+40
PWM signals can be routed to the user expansion header on am625 SK and am62 lp sk. Enable eCAP0, eCAP1, eHRPWM1, and route the output PWM signals to pins on J3 header. Signed-off-by: Judith Mendez <jm@ti.com> Reviewed-by: Bryan Brattlof <bb@ti.com> Link: https://lore.kernel.org/r/20250422000851.4118545-4-jm@ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-04-25arm64: dts: ti: k3-am62a7-sk: Enable PWMJudith Mendez1-0/+40
PWM signals can be routed to the user expansion header on am62a7 SK. Enable eCAP0, eCAP1, eHRPWM1, and route the output PWM signals to pins on J3 header. Signed-off-by: Judith Mendez <jm@ti.com> Reviewed-by: Bryan Brattlof <bb@ti.com> Link: https://lore.kernel.org/r/20250422000851.4118545-3-jm@ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-04-25arm64: dts: ti: k3-am62p5-sk: Enable PWMJudith Mendez1-0/+54
PWM signals can be routed to the user expansion header on am62p5 SK. Enable eCAP0, eCAP1, eHRPWM0, eHRPWM1 and route the output PWM signals to pins on J4 header. Signed-off-by: Judith Mendez <jm@ti.com> Reviewed-by: Bryan Brattlof <bb@ti.com> Link: https://lore.kernel.org/r/20250422000851.4118545-2-jm@ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-04-25arm64: dts: ti: Add basic support for phyBOARD-Izar-AM68xDominik Haller3-0/+1177
The phyCORE-AM68x/TDA4x [1] is a SoM (System on Module) featuring TI's AM68x/TDA4x SoC. It can be used in combination with different carrier boards. This module can come with different sizes and models for DDR, eMMC, SPI NOR Flash and various SoCs from the AM68x/TDA4x (J721S2) family. A reference carrier board design, called phyBOARD-Izar is used for the phyCORE-AM68x/TDA4x development kit [2]. Supported features: * Debug UART * 2x SPI NOR Flash * eMMC * 2x Ethernet * Micro SD card * I2C EEPROM * I2C RTC * 2x I2C GPIO Expander * LEDs * USB 5 Gbit/s * PCIe For more details see the product pages for the SoM and the development kit: [1] https://www.phytec.eu/en/produkte/system-on-modules/phycore-am68x-tda4x/ [2] https://www.phytec.eu/en/produkte/development-kits/phyboard-izar/ Signed-off-by: Dominik Haller <d.haller@phytec.de> Reviewed-by: Wadim Egorov <w.egorov@phytec.de> Reviewed-by: Udit Kumar <u-kumar1@ti.com> Acked-by: Moteen Shah <m-shah@ti.com> Link: https://lore.kernel.org/r/20250423133635.29897-2-d.haller@phytec.de Signed-off-by: Nishanth Menon <nm@ti.com>
2025-04-25arm64: defconfig: Enable TMP102 as moduleDominik Haller1-0/+1
Enable the driver for the TI TMP102 temperature sensors used on the Phytec phyCORE-AM68x/TDA4x and the phyGATE-Tauri-L-iMX8MM. Signed-off-by: Dominik Haller <d.haller@phytec.de> Reviewed-by: Udit Kumar <u-kumar1@ti.com> Link: https://lore.kernel.org/r/20250423133635.29897-3-d.haller@phytec.de Signed-off-by: Nishanth Menon <nm@ti.com>
2025-04-25arm64: defconfig: Enable hwspinlock and eQEP for K3Judith Mendez1-0/+2
Enable CONFIG_HWSPINLOCK_OMAP to allow usage of these devices across K3 SoC's. Also enable CONFIG_TI_EQEP which is enabled by default on am64x SK board. Signed-off-by: Judith Mendez <jm@ti.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20250421201055.3889680-1-jm@ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-04-25arm64: defconfig: Add CDNS_DSI and CDNS_PHY configJayesh Choudhary1-0/+2
Enable configs for cdns-dsi and cdns-dphy drivers required for DSI display on the following platforms: J721E-EVM, J721E-BeagleBone-AI64, J721S2-EVM, AM68-SK, J722S-EVM, BeagleY-AI, AM62P5-SK, J784S4-EVM and J742S2-EVM The DSI wrapper driver used by all the above mentioned platforms, cdns-dsi-j721e is enabled by default if cdns-dsi config is enabled. Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com> Reviewed-by: Judith Mendez <jm@ti.com> Link: https://lore.kernel.org/r/20250416182930.32132-1-j-choudhary@ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-04-25arm64: dts: ti: k3-j784s4-j742s2-main-common: Fix length of serdes_ln_ctrlSiddharth Vadapalli1-1/+1
Commit under Fixes corrected the "mux-reg-masks" property but did not update the "length" field of the "reg" property to account for the newly added register offsets which extend the region. Fix this. Fixes: 38e7f9092efb ("arm64: dts: ti: k3-j784s4-j742s2-main-common: Fix serdes_ln_ctrl reg-masks") Cc: stable@vger.kernel.org Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Udit Kumar <u-kumar1@ti.com> Link: https://lore.kernel.org/r/20250423151612.48848-1-s-vadapalli@ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-04-25arm64: dts: ti: am65x: Add missing power-supply for Rocktech-rk101 panelAndrew Davis1-0/+12
Add the 5v0 supply that is provided over the display panel cable and used by the LCD. This is required by "simple panels" or we get the following warning from DTBS_CHECK: k3-am654-gp-evm.dtb: display0: 'power-supply' is a required property Signed-off-by: Andrew Davis <afd@ti.com> Link: https://lore.kernel.org/r/20250421214620.3770172-4-afd@ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-04-25arm64: dts: ti: k3-am65-main: Add system controller compatibleJan Kiszka1-1/+1
Now that the TI K3 AM654 system controller bindings also cover the usage in the main domain, add its compatible to address dtbs_check complains: k3-am654-base-board.dtb: scm-conf@100000: compatible: ['syscon', 'simple-mfd'] is too short Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Andrew Davis <afd@ti.com> Link: https://lore.kernel.org/r/20250421214620.3770172-3-afd@ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-04-25arm64: dts: ti: k3-j721e-common-proc-board-infotainment: Update to comply ↵Jayesh Choudhary2-25/+38
with device tree schema Fix hdmi-connector and tfp bridge node as per the bindings, - Remove 'digital' property which is required for DVI connector not HDMI - Add 'ti,deskew' property which is a required property - Fix ports property for tfp410 bridge - Change node names appropriately Redefine the ports for dss and for k3-j721e-common-proc-board.dts, add reg property for the port (@0) to get rid of dtbs_check warnings in infotainment overlay when ports for dss are re-defined. Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com> Reviewed-by: Udit Kumar <u-kumar1@ti.com> Link: https://lore.kernel.org/r/20250424080328.57671-1-j-choudhary@ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
2025-04-25arm64: dts: imx8mq-evk: add pcie[0,1]-ep nodesFrank Li2-0/+23
Add pcie[0,1]-ep nodes and apply imx-pcie1-ep overlay file. Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8mq: add pcie0-ep nodeFrank Li1-0/+35
Add pcie0-ep node for i.MX8QM. Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8mm-evk: add pcie0-ep node and apply pcie0-ep overlay fileFrank Li2-0/+18
Add pcie0-ep node information and apply pcie0-ep overlay file. Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx95: add pcie1 ep overlay file and create pcie-ep dtb filesFrank Li4-0/+42
Create imx95-15x15-evk pcie0-ep and imx95-19x19-evk pcie[0,1]-ep dtb files. Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8: use common imx-pcie0-ep.dtso to enable PCI ep functionFrank Li5-30/+25
Use common imx-pcie0-ep.dtso for imx8mp-evk-pcie-ep and imx8qxp-mek-pcie-ep. No functional change. Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8dxl-evk: Add pcie0-ep node and use unified pcie0 labelFrank Li1-1/+11
Use unified pcie0 label and add pcie0-ep node. Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8dxl-ss-hsio: correct irq number for imx8dxlFrank Li1-0/+2
i.MX8DXL use difference irq number for PCIe EP DMA. Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8: create unified pcie0 and pcie0_ep label for all chipsFrank Li4-15/+24
Add unified pcie<n> and pcie<n>_ep label for existed chipes to prepare applied one overay file to enable EP function. Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8-apalis: Add PCIe and SATA supportMax Krummenacher5-36/+74
The needed drivers to support PCIe and SATA for i.MX 8QM have been added. Configure them for the Apalis iMX8 SoM. The pciea and pcieb blocks each get a single PCIe lane, pciea is available on the carrier boards while pcieb is connected to the on module Wi-Fi/BT module. The SATA lane is available on the carrier boards. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25Revert "arm64: dts: imx93-tqma9352-mba93xxla: enable Open Drain for MDIO"Markus Niebel1-4/+4
Using the MDIO pins with Open Drain causes spec violations of the signals. Revert the changes. This reverts commit 315d7f301e234b99c1b9619f0b14cf288dc7c33f. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25Revert "arm64: dts: imx93-tqma9352-mba93xxca: enable Open Drain for MDIO"Markus Niebel1-4/+4
Using the MDIO pins with Open Drain causes spec violations of the signals. Revert the changes. This reverts commit 9015397c2f2d9d327c0cf88d74e39c4858cb4912. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8mp-beacon: Enable RTC interrupt and wakeup-sourceAdam Ford1-0/+11
Enable the interrupts and wakeup-source to allow the external RTC to be used as an alarm. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8mn-beacon: Enable RTC interrupt and wakeup-sourceAdam Ford1-0/+11
Enable the interrupts and wakeup-source to allow the external RTC to be used as an alarm. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8mm-beacon: Enable RTC interrupt and wakeup-sourceAdam Ford1-0/+11
Enable the interrupts and wakeup-source to allow the external RTC to be used as an alarm. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8mn-beacon: Configure Ethernet PHY reset and GPIO IRQAdam Ford1-0/+4
The Ethernet PHY setup currently assumes that the bootloader will take the PHY out of reset, but this behavior is not guaranteed across all bootloaders. Add the reset GPIO to ensure the kernel can properly control the PHY reset line. Also configure the PHY IRQ GPIO to enable interrupt-driven link status reporting, instead of relying on polling. This ensures more reliable Ethernet initialization and improves PHY event handling. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8mm-beacon: Configure Ethernet PHY reset and GPIO IRQAdam Ford1-0/+4
The Ethernet PHY setup currently assumes that the bootloader will take the PHY out of reset, but this behavior is not guaranteed across all bootloaders. Add the reset GPIO to ensure the kernel can properly control the PHY reset line. Also configure the PHY IRQ GPIO to enable interrupt-driven link status reporting, instead of relying on polling. This ensures more reliable Ethernet initialization and improves PHY event handling. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8mn-beacon: Set SAI5 MCLK direction to output for HDMI audioAdam Ford1-0/+1
The HDMI bridge chip fails to generate an audio source due to the SAI5 master clock (MCLK) direction not being set to output. This prevents proper clocking of the HDMI audio interface. Add the `fsl,sai-mclk-direction-output` property to the SAI5 node to ensure the MCLK is driven by the SoC, resolving the HDMI sound issue. Fixes: 1d6880ceef43 ("arm64: dts: imx8mn-beacon: Add HDMI video with sound") Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8mm-beacon: Set SAI5 MCLK direction to output for HDMI audioAdam Ford1-0/+1
The HDMI bridge chip fails to generate an audio source due to the SAI5 master clock (MCLK) direction not being set to output. This prevents proper clocking of the HDMI audio interface. Add the `fsl,sai-mclk-direction-output` property to the SAI5 node to ensure the MCLK is driven by the SoC, resolving the HDMI sound issue. Fixes: 8ad7d14d99f3 ("arm64: dts: imx8mm-beacon: Add HDMI video with sound") Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8mp-beacon: Fix RTC capacitive loadAdam Ford1-0/+1
Although not noticeable when used every day, the RTC appears to drift when left to sit over time. This is due to the capacitive load not being properly set. Fix RTC drift by correcting the capacitive load setting from 7000 to 12500, which matches the actual hardware configuration. Fixes: 25a5ccdce767 ("arm64: dts: freescale: Introduce imx8mp-beacon-kit") Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8mn-beacon: Fix RTC capacitive loadAdam Ford1-0/+1
Although not noticeable when used every day, the RTC appears to drift when left to sit over time. This is due to the capacitive load not being properly set. Fix RTC drift by correcting the capacitive load setting from 7000 to 12500, which matches the actual hardware configuration. Fixes: 36ca3c8ccb53 ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit") Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8mm-beacon: Fix RTC capacitive loadAdam Ford1-0/+1
Although not noticeable when used every day, the RTC appears to drift when left to sit over time. This is due to the capacitive load not being properly set. Fix RTC drift by correcting the capacitive load setting from 7000 to 12500, which matches the actual hardware configuration. Fixes: 593816fa2f35 ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit") Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: add initial device tree for TQMa93xx/MBa91xxCAMarkus Niebel2-0/+750
This adds support for TQMa93xx module attached to MBa91xxCA board. TQMa93xx is a SOM using i.MX93 SOC. The SOM features PMIC, RAM, e-MMC and some optional peripherals like SPI-NOR, RTC, EEPROM, gyroscope and secure element. TQMa93xxCA can be attached directly while TQMa93xxLA needs an adapter. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: freescale: add Toradex SMARC iMX8MPVitor Soares3-0/+1582
Add DT support for Toradex SMARC iMX8MP SoM and Toradex SMARC Development carrier board. Link: https://www.toradex.com/computer-on-modules/smarc-arm-family/nxp-imx-8m-plus Link: https://www.toradex.com/products/carrier-board/smarc-development-board-kit Co-developed-by: Hiago De Franco <hiago.franco@toradex.com> Signed-off-by: Hiago De Franco <hiago.franco@toradex.com> Signed-off-by: Vitor Soares <vitor.soares@toradex.com> Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: s32gxxxa-rdb: Add PCA85073A RTC module over I2C0Ciprian Marian Costea1-0/+5
Add support for the PCA85073A RTC module connected via I2C0 on S32G274A-RDB2 and S32G399A-RDB3 boards. Note that the PCA85073A RTC module is not battery backed. Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Matthias Brugger <mbrugger@suse.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx95-15x15-evk: enable USB2.0 nodeXu Yang1-0/+16
On this board, USB2.0 is a host-only port, add vbus regulator node and enable USB2.0 node. Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx95-19x19-evk: enable USB2.0 nodeXu Yang1-0/+16
On this board, USB2.0 is a host-only port, add vbus regulator node and enable USB2.0 node. Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx95: add USB2.0 nodesXu Yang1-0/+30
Add USB2.0 controller and phy nodes. Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # TQMa95xxSA Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-25arm64: dts: imx8mp: Add device tree for Nitrogen8M Plus ENC Carrier BoardMartyn Welch3-0/+862
Add support for Boundary Devices/Ezurio Nitrogen8M Plus ENC Carrier Board and it's SOM. Supported interfaces: - Serial Console - EQoS Ethernet - USB - eMMC - HDMI Signed-off-by: Martyn Welch <martyn.welch@collabora.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-04-24Merge tag 'kvmarm-fixes-6.15-2' of ↵Paolo Bonzini4-17/+25
https://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD KVM/arm64 fixes for 6.15, round #2 - Single fix for broken usage of 'multi-MIDR' infrastructure in PI code, adding an open-coded erratum check for everyone's favorite pile of sand: Cavium ThunderX
2025-04-24KVM: arm64, x86: make kvm_arch_has_irq_bypass() inlinePaolo Bonzini2-5/+5
kvm_arch_has_irq_bypass() is a small function and even though it does not appear in any *really* hot paths, it's also not entirely rare. Make it inline---it also works out nicely in preparation for using it in kvm-intel.ko and kvm-amd.ko, since the function is not currently exported. Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2025-04-24arm64: dts: renesas: r8a779h0: Add ISP core function blockNiklas Söderlund1-5/+16
The first ISP instance on V4M has both a channel select and core function block, describe the core region in addition to the existing cs region. While at it update the second ISP to match the new bindings and add the reg-names and interrupt-names property. Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/20250423163113.2961049-5-niklas.soderlund+renesas@ragnatech.se Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2025-04-24arm64: dts: renesas: r8a779g0: Add ISP core function blockNiklas Söderlund1-8/+22
All ISP instances on V4H have both a channel select and core function block, describe the core region in addition to the existing cs region. Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/20250423163113.2961049-4-niklas.soderlund+renesas@ragnatech.se Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2025-04-24arm64: dts: renesas: r8a779a0: Add ISP core function blockNiklas Söderlund1-16/+44
All ISP instances on V3U have both a channel select and core function block, describe the core region in addition to the existing cs region. The interrupt number already described intended to reflect the cs function but did incorrectly describe the core block. This was not noticed until now as the driver do not make use of the interrupt for the cs block. Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/20250423163113.2961049-3-niklas.soderlund+renesas@ragnatech.se Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-13 19:28:29 +0300